/** Does the chip support rev1 DMA packets? */
#define CHIP_HAS_REV1_DMA_PACKETS() 0
+/** Does the chip have an IPI shim? */
+#define CHIP_HAS_IPI() 0
+
#endif /* !__OPEN_SOURCE__ */
#endif /* __ARCH_CHIP_H__ */
/** Does the chip support rev1 DMA packets? */
#define CHIP_HAS_REV1_DMA_PACKETS() 1
+/** Does the chip have an IPI shim? */
+#define CHIP_HAS_IPI() 0
+
#endif /* !__OPEN_SOURCE__ */
#endif /* __ARCH_CHIP_H__ */
/* IRQ numbers used for linux IPIs. */
#define IRQ_RESCHEDULE 1
-/* The HV interrupt state object. */
-DECLARE_PER_CPU(HV_IntrState, dev_intr_state);
-
void ack_bad_irq(unsigned int irq);
/*
- * Paravirtualized drivers should call this when their init calls
- * discover a valid HV IRQ.
+ * Different ways of handling interrupts. Tile interrupts are always
+ * per-cpu; there is no global interrupt controller to implement
+ * enable/disable. Most onboard devices can send their interrupts to
+ * many tiles at the same time, and Tile-specific drivers know how to
+ * deal with this.
+ *
+ * However, generic devices (usually PCIE based, sometimes GPIO)
+ * expect that interrupts will fire on a single core at a time and
+ * that the irq can be enabled or disabled from any core at any time.
+ * We implement this by directing such interrupts to a single core.
+ *
+ * One added wrinkle is that PCI interrupts can be either
+ * hardware-cleared (legacy interrupts) or software cleared (MSI).
+ * Other generic device systems (GPIO) are always software-cleared.
+ *
+ * The enums below are used by drivers for onboard devices, including
+ * the internals of PCI root complex and GPIO. They allow the driver
+ * to tell the generic irq code what kind of interrupt is mapped to a
+ * particular IRQ number.
+ */
+enum {
+ /* per-cpu interrupt; use enable/disable_percpu_irq() to mask */
+ TILE_IRQ_PERCPU,
+ /* global interrupt, hardware responsible for clearing. */
+ TILE_IRQ_HW_CLEAR,
+ /* global interrupt, software responsible for clearing. */
+ TILE_IRQ_SW_CLEAR,
+};
+
+
+/*
+ * Paravirtualized drivers should call this when they dynamically
+ * allocate a new IRQ or discover an IRQ that was pre-allocated by the
+ * hypervisor for use with their particular device. This gives the
+ * IRQ subsystem an opportunity to do interrupt-type-specific
+ * initialization.
+ *
+ * ISSUE: We should modify this API so that registering anything
+ * except percpu interrupts also requires providing callback methods
+ * for enabling and disabling the interrupt. This would allow the
+ * generic IRQ code to proxy enable/disable_irq() calls back into the
+ * PCI subsystem, which in turn could enable or disable the interrupt
+ * at the PCI shim.
*/
-void tile_irq_activate(unsigned int irq);
+void tile_irq_activate(unsigned int irq, int tile_irq_type);
+
+/*
+ * For onboard, non-PCI (e.g. TILE_IRQ_PERCPU) devices, drivers know
+ * how to use enable/disable_percpu_irq() to manage interrupts on each
+ * core. We can't use the generic enable/disable_irq() because they
+ * use a single reference count per irq, rather than per cpu per irq.
+ */
+void enable_percpu_irq(unsigned int irq);
+void disable_percpu_irq(unsigned int irq);
+
+
+void setup_irq_regs(void);
#endif /* _ASM_TILE_IRQ_H */
#include <asm/processor.h>
#include <linux/cpumask.h>
#include <linux/irqreturn.h>
+#include <hv/hypervisor.h>
/* Set up this tile to support receiving hypervisor messages */
void init_messaging(void);
/* Process an IPI message */
void evaluate_message(int tag);
-/* Process an IRQ_RESCHEDULE IPI. */
-irqreturn_t handle_reschedule_ipi(int irq, void *token);
-
/* Boot a secondary cpu */
void online_secondary(void);
#define smp_height (smp_topology.height)
#define smp_width (smp_topology.width)
+/* Convenience functions for converting cpu <-> coords. */
+static inline int cpu_x(int cpu)
+{
+ return cpu % smp_width;
+}
+static inline int cpu_y(int cpu)
+{
+ return cpu / smp_width;
+}
+static inline int xy_to_cpu(int x, int y)
+{
+ return y * smp_width + x;
+}
+
/* Hypervisor message tags sent via the tile send_IPI*() routines. */
#define MSG_TAG_START_CPU 1
#define MSG_TAG_STOP_CPU 2
#define smp_master_cpu 0
#define smp_height 1
#define smp_width 1
+#define cpu_x(cpu) 0
+#define cpu_y(cpu) 0
+#define xy_to_cpu(x, y) 0
#endif /* !CONFIG_SMP */
return bitmap_parselist_crop(buf, cpumask_bits(dstp), nbits);
}
+/* Initialize the IPI subsystem. */
+void ipi_init(void);
+
+/* Function for start-cpu message to cause us to jump to. */
+extern unsigned long start_cpu_function_addr;
+
#endif /* _ASM_TILE_SMP_H */
#ifndef _TILE_HV_H
#define _TILE_HV_H
-#ifdef __tile__
#include <arch/chip.h>
-#else
-/* HACK: Allow use by "tools/cpack/". */
-#include "install/include/arch/chip.h"
-#endif
+
+#include <hv/pagesize.h>
/* Linux builds want unsigned long constants, but assembler wants numbers */
#ifdef __ASSEMBLER__
#define __HV_SIZE_ONE 1UL
#endif
-
/** The log2 of the span of a level-1 page table, in bytes.
*/
#define HV_LOG2_L1_SPAN 32
*/
#define HV_L1_SPAN (__HV_SIZE_ONE << HV_LOG2_L1_SPAN)
-/** The log2 of the size of small pages, in bytes. This value should
- * be verified at runtime by calling hv_sysconf(HV_SYSCONF_PAGE_SIZE_SMALL).
- */
-#define HV_LOG2_PAGE_SIZE_SMALL 16
-
/** The size of small pages, in bytes. This value should be verified
* at runtime by calling hv_sysconf(HV_SYSCONF_PAGE_SIZE_SMALL).
*/
#define HV_PAGE_SIZE_SMALL (__HV_SIZE_ONE << HV_LOG2_PAGE_SIZE_SMALL)
-/** The log2 of the size of large pages, in bytes. This value should be
- * verified at runtime by calling hv_sysconf(HV_SYSCONF_PAGE_SIZE_LARGE).
- */
-#define HV_LOG2_PAGE_SIZE_LARGE 24
-
/** The size of large pages, in bytes. This value should be verified
* at runtime by calling hv_sysconf(HV_SYSCONF_PAGE_SIZE_LARGE).
*/
#define HV_DISPATCH_ENTRY_SIZE 32
/** Version of the hypervisor interface defined by this file */
-#define _HV_VERSION 10
+#define _HV_VERSION 11
/* Index into hypervisor interface dispatch code blocks.
*
/** hv_set_command_line */
#define HV_DISPATCH_SET_COMMAND_LINE 47
-/** hv_dev_register_intr_state */
-#define HV_DISPATCH_DEV_REGISTER_INTR_STATE 48
+#if !CHIP_HAS_IPI()
+
+/** hv_clear_intr */
+#define HV_DISPATCH_CLEAR_INTR 48
/** hv_enable_intr */
#define HV_DISPATCH_ENABLE_INTR 49
/** hv_disable_intr */
#define HV_DISPATCH_DISABLE_INTR 50
+/** hv_raise_intr */
+#define HV_DISPATCH_RAISE_INTR 51
+
/** hv_trigger_ipi */
-#define HV_DISPATCH_TRIGGER_IPI 51
+#define HV_DISPATCH_TRIGGER_IPI 52
+
+#endif /* !CHIP_HAS_IPI() */
/** hv_store_mapping */
-#define HV_DISPATCH_STORE_MAPPING 52
+#define HV_DISPATCH_STORE_MAPPING 53
/** hv_inquire_realpa */
-#define HV_DISPATCH_INQUIRE_REALPA 53
+#define HV_DISPATCH_INQUIRE_REALPA 54
/** hv_flush_all */
-#define HV_DISPATCH_FLUSH_ALL 54
+#define HV_DISPATCH_FLUSH_ALL 55
+
+#if CHIP_HAS_IPI()
+/** hv_get_ipi_pte */
+#define HV_DISPATCH_GET_IPI_PTE 56
+#endif
/** One more than the largest dispatch value */
-#define _HV_DISPATCH_END 55
+#define _HV_DISPATCH_END 57
#ifndef __ASSEMBLER__
*/
int hv_confstr(HV_ConfstrQuery query, HV_VirtAddr buf, int len);
-/** State object used to enable and disable one-shot and level-sensitive
- * interrupts. */
-typedef struct
-{
-#if CHIP_VA_WIDTH() > 32
- __hv64 opaque[2]; /**< No user-serviceable parts inside */
-#else
- __hv32 opaque[2]; /**< No user-serviceable parts inside */
-#endif
-}
-HV_IntrState;
-
-/** A set of interrupts. */
-typedef __hv32 HV_IntrMask;
-
/** Tile coordinate */
typedef struct
{
int y;
} HV_Coord;
+
+#if CHIP_HAS_IPI()
+
+/** Get the PTE for sending an IPI to a particular tile.
+ *
+ * @param tile Tile which will receive the IPI.
+ * @param pl Indicates which IPI registers: 0 = IPI_0, 1 = IPI_1.
+ * @param pte Filled with resulting PTE.
+ * @result Zero if no error, non-zero for invalid parameters.
+ */
+int hv_get_ipi_pte(HV_Coord tile, int pl, HV_PTE* pte);
+
+#else /* !CHIP_HAS_IPI() */
+
+/** A set of interrupts. */
+typedef __hv32 HV_IntrMask;
+
/** The low interrupt numbers are reserved for use by the client in
* delivering IPIs. Any interrupt numbers higher than this value are
* reserved for use by HV device drivers. */
#define HV_MAX_IPI_INTERRUPT 7
-/** Register an interrupt state object. This object is used to enable and
- * disable one-shot and level-sensitive interrupts. Once the state is
- * registered, the client must not read or write the state object; doing
- * so will cause undefined results.
+/** Enable a set of device interrupts.
*
- * @param intr_state Pointer to interrupt state object.
- * @return HV_OK on success, or a hypervisor error code.
+ * @param enab_mask Bitmap of interrupts to enable.
*/
-HV_Errno hv_dev_register_intr_state(HV_IntrState* intr_state);
+void hv_enable_intr(HV_IntrMask enab_mask);
-/** Enable a set of one-shot and level-sensitive interrupts.
+/** Disable a set of device interrupts.
*
- * @param intr_state Pointer to interrupt state object.
- * @param enab_mask Bitmap of interrupts to enable.
+ * @param disab_mask Bitmap of interrupts to disable.
*/
-void hv_enable_intr(HV_IntrState* intr_state, HV_IntrMask enab_mask);
+void hv_disable_intr(HV_IntrMask disab_mask);
-/** Disable a set of one-shot and level-sensitive interrupts.
+/** Clear a set of device interrupts.
*
- * @param intr_state Pointer to interrupt state object.
- * @param disab_mask Bitmap of interrupts to disable.
+ * @param clear_mask Bitmap of interrupts to clear.
*/
-void hv_disable_intr(HV_IntrState* intr_state, HV_IntrMask disab_mask);
+void hv_clear_intr(HV_IntrMask clear_mask);
+
+/** Assert a set of device interrupts.
+ *
+ * @param assert_mask Bitmap of interrupts to clear.
+ */
+void hv_assert_intr(HV_IntrMask assert_mask);
/** Trigger a one-shot interrupt on some tile
*
*/
HV_Errno hv_trigger_ipi(HV_Coord tile, int interrupt);
+#endif // !CHIP_HAS_IPI()
+
/** Store memory mapping in debug memory so that external debugger can read it.
* A maximum of 16 entries can be stored.
*
* it will return to the code which was interrupted by the INTCTRL_1
* interrupt.
*
+ * Under some circumstances, the firing of INTCTRL_1 can race with
+ * the lowering of a device interrupt. In such a case, the
+ * hv_downcall_dispatch service may issue an iret instruction instead
+ * of entering one of the client's actual downcall-handling interrupt
+ * vectors. This will return execution to the location that was
+ * interrupted by INTCTRL_1.
+ *
* Any saving of registers should be done by the actual handling
* vectors; no registers should be changed by the INTCTRL_1 handler.
* In particular, the client should not use a jal instruction to invoke
--- /dev/null
+/*
+ * Copyright 2010 Tilera Corporation. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation, version 2.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, GOOD TITLE or
+ * NON INFRINGEMENT. See the GNU General Public License for
+ * more details.
+ */
+
+/**
+ * @file pagesize.h
+ */
+
+#ifndef _HV_PAGESIZE_H
+#define _HV_PAGESIZE_H
+
+/** The log2 of the size of small pages, in bytes. This value should
+ * be verified at runtime by calling hv_sysconf(HV_SYSCONF_PAGE_SIZE_SMALL).
+ */
+#define HV_LOG2_PAGE_SIZE_SMALL 16
+
+/** The log2 of the size of large pages, in bytes. This value should be
+ * verified at runtime by calling hv_sysconf(HV_SYSCONF_PAGE_SIZE_LARGE).
+ */
+#define HV_LOG2_PAGE_SIZE_LARGE 24
+
+#endif /* _HV_PAGESIZE_H */
hv_confstr = TEXT_OFFSET + 0x105a0;
hv_reexec = TEXT_OFFSET + 0x105c0;
hv_set_command_line = TEXT_OFFSET + 0x105e0;
-hv_dev_register_intr_state = TEXT_OFFSET + 0x10600;
+hv_clear_intr = TEXT_OFFSET + 0x10600;
hv_enable_intr = TEXT_OFFSET + 0x10620;
hv_disable_intr = TEXT_OFFSET + 0x10640;
-hv_trigger_ipi = TEXT_OFFSET + 0x10660;
-hv_store_mapping = TEXT_OFFSET + 0x10680;
-hv_inquire_realpa = TEXT_OFFSET + 0x106a0;
-hv_flush_all = TEXT_OFFSET + 0x106c0;
-hv_glue_internals = TEXT_OFFSET + 0x106e0;
+hv_raise_intr = TEXT_OFFSET + 0x10660;
+hv_trigger_ipi = TEXT_OFFSET + 0x10680;
+hv_store_mapping = TEXT_OFFSET + 0x106a0;
+hv_inquire_realpa = TEXT_OFFSET + 0x106c0;
+hv_flush_all = TEXT_OFFSET + 0x106e0;
+hv_get_ipi_pte = TEXT_OFFSET + 0x10700;
+hv_glue_internals = TEXT_OFFSET + 0x10720;
#include <linux/kernel_stat.h>
#include <linux/uaccess.h>
#include <hv/drv_pcie_rc_intf.h>
+#include <arch/spr_def.h>
+#include <asm/traps.h>
+
+/* Bit-flag stored in irq_desc->chip_data to indicate HW-cleared irqs. */
+#define IS_HW_CLEARED 1
/*
* The set of interrupts we enable for raw_local_irq_enable().
INITIAL_INTERRUPTS_ENABLED;
EXPORT_PER_CPU_SYMBOL(interrupts_enabled_mask);
-/* Define per-tile device interrupt state */
-DEFINE_PER_CPU(HV_IntrState, dev_intr_state);
-
+/* Define per-tile device interrupt statistics state. */
DEFINE_PER_CPU(irq_cpustat_t, irq_stat) ____cacheline_internodealigned_in_smp;
EXPORT_PER_CPU_SYMBOL(irq_stat);
+/*
+ * Define per-tile irq disable mask; the hardware/HV only has a single
+ * mask that we use to implement both masking and disabling.
+ */
+static DEFINE_PER_CPU(unsigned long, irq_disable_mask)
+ ____cacheline_internodealigned_in_smp;
+
+/*
+ * Per-tile IRQ nesting depth. Used to make sure we enable newly
+ * enabled IRQs before exiting the outermost interrupt.
+ */
+static DEFINE_PER_CPU(int, irq_depth);
+
+/* State for allocating IRQs on Gx. */
+#if CHIP_HAS_IPI()
+static unsigned long available_irqs = ~(1UL << IRQ_RESCHEDULE);
+static DEFINE_SPINLOCK(available_irqs_lock);
+#endif
+#if CHIP_HAS_IPI()
+/* Use SPRs to manipulate device interrupts. */
+#define mask_irqs(irq_mask) __insn_mtspr(SPR_IPI_MASK_SET_1, irq_mask)
+#define unmask_irqs(irq_mask) __insn_mtspr(SPR_IPI_MASK_RESET_1, irq_mask)
+#define clear_irqs(irq_mask) __insn_mtspr(SPR_IPI_EVENT_RESET_1, irq_mask)
+#else
+/* Use HV to manipulate device interrupts. */
+#define mask_irqs(irq_mask) hv_disable_intr(irq_mask)
+#define unmask_irqs(irq_mask) hv_enable_intr(irq_mask)
+#define clear_irqs(irq_mask) hv_clear_intr(irq_mask)
+#endif
/*
- * Interrupt dispatcher, invoked upon a hypervisor device interrupt downcall
+ * The interrupt handling path, implemented in terms of HV interrupt
+ * emulation on TILE64 and TILEPro, and IPI hardware on TILE-Gx.
*/
void tile_dev_intr(struct pt_regs *regs, int intnum)
{
- int irq;
+ int depth = __get_cpu_var(irq_depth)++;
+ unsigned long original_irqs;
+ unsigned long remaining_irqs;
+ struct pt_regs *old_regs;
+#if CHIP_HAS_IPI()
/*
- * Get the device interrupt pending mask from where the hypervisor
- * has tucked it away for us.
+ * Pending interrupts are listed in an SPR. We might be
+ * nested, so be sure to only handle irqs that weren't already
+ * masked by a previous interrupt. Then, mask out the ones
+ * we're going to handle.
*/
- unsigned long pending_dev_intr_mask = __insn_mfspr(SPR_SYSTEM_SAVE_1_3);
-
+ unsigned long masked = __insn_mfspr(SPR_IPI_MASK_1);
+ original_irqs = __insn_mfspr(SPR_IPI_EVENT_1) & ~masked;
+ __insn_mtspr(SPR_IPI_MASK_SET_1, original_irqs);
+#else
+ /*
+ * Hypervisor performs the equivalent of the Gx code above and
+ * then puts the pending interrupt mask into a system save reg
+ * for us to find.
+ */
+ original_irqs = __insn_mfspr(SPR_SYSTEM_SAVE_1_3);
+#endif
+ remaining_irqs = original_irqs;
/* Track time spent here in an interrupt context. */
- struct pt_regs *old_regs = set_irq_regs(regs);
+ old_regs = set_irq_regs(regs);
irq_enter();
#ifdef CONFIG_DEBUG_STACKOVERFLOW
{
long sp = stack_pointer - (long) current_thread_info();
if (unlikely(sp < (sizeof(struct thread_info) + STACK_WARN))) {
- printk(KERN_EMERG "tile_dev_intr: "
+ pr_emerg("tile_dev_intr: "
"stack overflow: %ld\n",
sp - sizeof(struct thread_info));
dump_stack();
}
}
#endif
+ while (remaining_irqs) {
+ unsigned long irq = __ffs(remaining_irqs);
+ remaining_irqs &= ~(1UL << irq);
- for (irq = 0; pending_dev_intr_mask; ++irq) {
- if (pending_dev_intr_mask & 0x1) {
- generic_handle_irq(irq);
+ /* Count device irqs; Linux IPIs are counted elsewhere. */
+ if (irq != IRQ_RESCHEDULE)
+ __get_cpu_var(irq_stat).irq_dev_intr_count++;
- /* Count device irqs; IPIs are counted elsewhere. */
- if (irq > HV_MAX_IPI_INTERRUPT)
- __get_cpu_var(irq_stat).irq_dev_intr_count++;
- }
- pending_dev_intr_mask >>= 1;
+ generic_handle_irq(irq);
}
+ /*
+ * If we weren't nested, turn on all enabled interrupts,
+ * including any that were reenabled during interrupt
+ * handling.
+ */
+ if (depth == 0)
+ unmask_irqs(~__get_cpu_var(irq_disable_mask));
+
+ __get_cpu_var(irq_depth)--;
+
/*
* Track time spent against the current process again and
* process any softirqs if they are waiting.
}
+/*
+ * Remove an irq from the disabled mask. If we're in an interrupt
+ * context, defer enabling the HW interrupt until we leave.
+ */
+void enable_percpu_irq(unsigned int irq)
+{
+ get_cpu_var(irq_disable_mask) &= ~(1UL << irq);
+ if (__get_cpu_var(irq_depth) == 0)
+ unmask_irqs(1UL << irq);
+ put_cpu_var(irq_disable_mask);
+}
+EXPORT_SYMBOL(enable_percpu_irq);
+
+/*
+ * Add an irq to the disabled mask. We disable the HW interrupt
+ * immediately so that there's no possibility of it firing. If we're
+ * in an interrupt context, the return path is careful to avoid
+ * unmasking a newly disabled interrupt.
+ */
+void disable_percpu_irq(unsigned int irq)
+{
+ get_cpu_var(irq_disable_mask) |= (1UL << irq);
+ mask_irqs(1UL << irq);
+ put_cpu_var(irq_disable_mask);
+}
+EXPORT_SYMBOL(disable_percpu_irq);
+
/* Mask an interrupt. */
-static void hv_dev_irq_mask(unsigned int irq)
+static void tile_irq_chip_mask(unsigned int irq)
{
- HV_IntrState *p_intr_state = &__get_cpu_var(dev_intr_state);
- hv_disable_intr(p_intr_state, 1 << irq);
+ mask_irqs(1UL << irq);
}
/* Unmask an interrupt. */
-static void hv_dev_irq_unmask(unsigned int irq)
+static void tile_irq_chip_unmask(unsigned int irq)
{
- /* Re-enable the hypervisor to generate interrupts. */
- HV_IntrState *p_intr_state = &__get_cpu_var(dev_intr_state);
- hv_enable_intr(p_intr_state, 1 << irq);
+ unmask_irqs(1UL << irq);
}
/*
- * The HV doesn't latch incoming interrupts while an interrupt is
- * disabled, so we need to reenable interrupts before running the
- * handler.
- *
- * ISSUE: Enabling the interrupt this early avoids any race conditions
- * but introduces the possibility of nested interrupt stack overflow.
- * An imminent change to the HV IRQ model will fix this.
+ * Clear an interrupt before processing it so that any new assertions
+ * will trigger another irq.
*/
-static void hv_dev_irq_ack(unsigned int irq)
+static void tile_irq_chip_ack(unsigned int irq)
{
- hv_dev_irq_unmask(irq);
+ if ((unsigned long)get_irq_chip_data(irq) != IS_HW_CLEARED)
+ clear_irqs(1UL << irq);
}
/*
- * Since ack() reenables interrupts, there's nothing to do at eoi().
+ * For per-cpu interrupts, we need to avoid unmasking any interrupts
+ * that we disabled via disable_percpu_irq().
*/
-static void hv_dev_irq_eoi(unsigned int irq)
+static void tile_irq_chip_eoi(unsigned int irq)
{
+ if (!(__get_cpu_var(irq_disable_mask) & (1UL << irq)))
+ unmask_irqs(1UL << irq);
}
-static struct irq_chip hv_dev_irq_chip = {
- .typename = "hv_dev_irq_chip",
- .ack = hv_dev_irq_ack,
- .mask = hv_dev_irq_mask,
- .unmask = hv_dev_irq_unmask,
- .eoi = hv_dev_irq_eoi,
-};
-
-static struct irqaction resched_action = {
- .handler = handle_reschedule_ipi,
- .name = "resched",
- .dev_id = handle_reschedule_ipi /* unique token */,
+static struct irq_chip tile_irq_chip = {
+ .typename = "tile_irq_chip",
+ .ack = tile_irq_chip_ack,
+ .eoi = tile_irq_chip_eoi,
+ .mask = tile_irq_chip_mask,
+ .unmask = tile_irq_chip_unmask,
};
void __init init_IRQ(void)
{
- /* Bind IPI irqs. Does this belong somewhere else in init? */
- tile_irq_activate(IRQ_RESCHEDULE);
- BUG_ON(setup_irq(IRQ_RESCHEDULE, &resched_action));
+ ipi_init();
}
-void __cpuinit init_per_tile_IRQs(void)
+void __cpuinit setup_irq_regs(void)
{
- int rc;
-
- /* Set the pointer to the per-tile device interrupt state. */
- HV_IntrState *sv_ptr = &__get_cpu_var(dev_intr_state);
- rc = hv_dev_register_intr_state(sv_ptr);
- if (rc != HV_OK)
- panic("hv_dev_register_intr_state: error %d", rc);
-
+ /* Enable interrupt delivery. */
+ unmask_irqs(~0UL);
+#if CHIP_HAS_IPI()
+ raw_local_irq_unmask(INT_IPI_1);
+#endif
}
-void tile_irq_activate(unsigned int irq)
+void tile_irq_activate(unsigned int irq, int tile_irq_type)
{
/*
- * Paravirtualized drivers can call up to the HV to find out
- * which irq they're associated with. The HV interface
- * doesn't provide a generic call for discovering all valid
- * IRQs, so drivers must call this method to initialize newly
- * discovered IRQs.
- *
- * We could also just initialize all 32 IRQs at startup, but
- * doing so would lead to a kernel fault if an unexpected
- * interrupt fires and jumps to a NULL action. By defering
- * the set_irq_chip_and_handler() call, unexpected IRQs are
- * handled properly by handle_bad_irq().
+ * We use handle_level_irq() by default because the pending
+ * interrupt vector (whether modeled by the HV on TILE64 and
+ * TILEPro or implemented in hardware on TILE-Gx) has
+ * level-style semantics for each bit. An interrupt fires
+ * whenever a bit is high, not just at edges.
+ */
+ irq_flow_handler_t handle = handle_level_irq;
+ if (tile_irq_type == TILE_IRQ_PERCPU)
+ handle = handle_percpu_irq;
+ set_irq_chip_and_handler(irq, &tile_irq_chip, handle);
+
+ /*
+ * Flag interrupts that are hardware-cleared so that ack()
+ * won't clear them.
*/
- hv_dev_irq_mask(irq);
- set_irq_chip_and_handler(irq, &hv_dev_irq_chip, handle_percpu_irq);
+ if (tile_irq_type == TILE_IRQ_HW_CLEAR)
+ set_irq_chip_data(irq, (void *)IS_HW_CLEARED);
}
+EXPORT_SYMBOL(tile_irq_activate);
+
void ack_bad_irq(unsigned int irq)
{
- printk(KERN_ERR "unexpected IRQ trap at vector %02x\n", irq);
+ pr_err("unexpected IRQ trap at vector %02x\n", irq);
}
/*
}
return 0;
}
+
+#if CHIP_HAS_IPI()
+int create_irq(void)
+{
+ unsigned long flags;
+ int result;
+
+ spin_lock_irqsave(&available_irqs_lock, flags);
+ if (available_irqs == 0)
+ result = -ENOMEM;
+ else {
+ result = __ffs(available_irqs);
+ available_irqs &= ~(1UL << result);
+ dynamic_irq_init(result);
+ }
+ spin_unlock_irqrestore(&available_irqs_lock, flags);
+
+ return result;
+}
+EXPORT_SYMBOL(create_irq);
+
+void destroy_irq(unsigned int irq)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&available_irqs_lock, flags);
+ available_irqs |= (1UL << irq);
+ dynamic_irq_cleanup(irq);
+ spin_unlock_irqrestore(&available_irqs_lock, flags);
+}
+EXPORT_SYMBOL(destroy_irq);
+#endif
*/
#include <linux/smp.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
#include <linux/irq.h>
+#include <linux/module.h>
#include <asm/cacheflush.h>
HV_Topology smp_topology __write_once;
+EXPORT_SYMBOL(smp_topology);
+
+#if CHIP_HAS_IPI()
+static unsigned long __iomem *ipi_mappings[NR_CPUS];
+#endif
/*
/* Handler to start the current cpu. */
static void smp_start_cpu_interrupt(void)
{
- extern unsigned long start_cpu_function_addr;
get_irq_regs()->pc = start_cpu_function_addr;
}
}
-/*
- * The smp_send_reschedule() path does not use the hv_message_intr()
- * path but instead the faster tile_dev_intr() path for interrupts.
- */
-
-irqreturn_t handle_reschedule_ipi(int irq, void *token)
+/* Called when smp_send_reschedule() triggers IRQ_RESCHEDULE. */
+static irqreturn_t handle_reschedule_ipi(int irq, void *token)
{
/*
* Nothing to do here; when we return from interrupt, the
return IRQ_HANDLED;
}
+static struct irqaction resched_action = {
+ .handler = handle_reschedule_ipi,
+ .name = "resched",
+ .dev_id = handle_reschedule_ipi /* unique token */,
+};
+
+void __init ipi_init(void)
+{
+#if CHIP_HAS_IPI()
+ int cpu;
+ /* Map IPI trigger MMIO addresses. */
+ for_each_possible_cpu(cpu) {
+ HV_Coord tile;
+ HV_PTE pte;
+ unsigned long offset;
+
+ tile.x = cpu_x(cpu);
+ tile.y = cpu_y(cpu);
+ if (hv_get_ipi_pte(tile, 1, &pte) != 0)
+ panic("Failed to initialize IPI for cpu %d\n", cpu);
+
+ offset = hv_pte_get_pfn(pte) << PAGE_SHIFT;
+ ipi_mappings[cpu] = ioremap_prot(offset, PAGE_SIZE, pte);
+ }
+#endif
+
+ /* Bind handle_reschedule_ipi() to IRQ_RESCHEDULE. */
+ tile_irq_activate(IRQ_RESCHEDULE, TILE_IRQ_PERCPU);
+ BUG_ON(setup_irq(IRQ_RESCHEDULE, &resched_action));
+}
+
+#if CHIP_HAS_IPI()
+
+void smp_send_reschedule(int cpu)
+{
+ WARN_ON(cpu_is_offline(cpu));
+
+ /*
+ * We just want to do an MMIO store. The traditional writeq()
+ * functions aren't really correct here, since they're always
+ * directed at the PCI shim. For now, just do a raw store,
+ * casting away the __iomem attribute.
+ */
+ ((unsigned long __force *)ipi_mappings[cpu])[IRQ_RESCHEDULE] = 0;
+}
+
+#else
+
void smp_send_reschedule(int cpu)
{
HV_Coord coord;
WARN_ON(cpu_is_offline(cpu));
- coord.y = cpu / smp_width;
- coord.x = cpu % smp_width;
+
+ coord.y = cpu_y(cpu);
+ coord.x = cpu_x(cpu);
hv_trigger_ipi(coord, IRQ_RESCHEDULE);
}
+
+#endif /* CHIP_HAS_IPI() */
git://bbs.cooldavid.org / net-next-2.6.git / commitdiff