config CPU_SH2A
bool
select CPU_SH2
+ select UNCACHED_MAPPING
config CPU_SH3
bool
machdir-$(CONFIG_SH_HP6XX) += mach-hp6xx
machdir-$(CONFIG_SH_DREAMCAST) += mach-dreamcast
machdir-$(CONFIG_SH_SH03) += mach-sh03
-machdir-$(CONFIG_SH_SECUREEDGE5410) += mach-snapgear
machdir-$(CONFIG_SH_RTS7751R2D) += mach-r2d
-machdir-$(CONFIG_SH_7751_SYSTEMH) += mach-systemh
-machdir-$(CONFIG_SH_EDOSK7705) += mach-edosk7705
machdir-$(CONFIG_SH_HIGHLANDER) += mach-highlander
machdir-$(CONFIG_SH_MIGOR) += mach-migor
machdir-$(CONFIG_SH_AP325RXA) += mach-ap325rxa
Select 7343 SolutionEngine if configuring for a Hitachi
SH7343 (SH-Mobile 3AS) evaluation board.
-config SH_7751_SYSTEMH
- bool "SystemH7751R"
- depends on CPU_SUBTYPE_SH7751R
- help
- Select SystemH if you are configuring for a Renesas SystemH
- 7751R evaluation board.
-
config SH_HP6XX
bool "HP6XX"
select SYS_SUPPORTS_APM_EMULATION
# Specific board support, not covered by a mach group.
#
obj-$(CONFIG_SH_MAGIC_PANEL_R2) += board-magicpanelr2.o
+obj-$(CONFIG_SH_SECUREEDGE5410) += board-secureedge5410.o
obj-$(CONFIG_SH_SH2007) += board-sh2007.o
obj-$(CONFIG_SH_SH7785LCR) += board-sh7785lcr.o
obj-$(CONFIG_SH_URQUELL) += board-urquell.o
obj-$(CONFIG_SH_SHMIN) += board-shmin.o
+obj-$(CONFIG_SH_EDOSK7705) += board-edosk7705.o
obj-$(CONFIG_SH_EDOSK7760) += board-edosk7760.o
obj-$(CONFIG_SH_ESPT) += board-espt.o
obj-$(CONFIG_SH_POLARIS) += board-polaris.o
--- /dev/null
+/*
+ * arch/sh/boards/renesas/edosk7705/setup.c
+ *
+ * Copyright (C) 2000 Kazumoto Kojima
+ *
+ * Hitachi SolutionEngine Support.
+ *
+ * Modified for edosk7705 development
+ * board by S. Dunn, 2003.
+ */
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/smc91x.h>
+#include <asm/machvec.h>
+#include <asm/sizes.h>
+
+#define SMC_IOBASE 0xA2000000
+#define SMC_IO_OFFSET 0x300
+#define SMC_IOADDR (SMC_IOBASE + SMC_IO_OFFSET)
+
+#define ETHERNET_IRQ 0x09
+
+static void __init sh_edosk7705_init_irq(void)
+{
+ make_imask_irq(ETHERNET_IRQ);
+}
+
+/* eth initialization functions */
+static struct smc91x_platdata smc91x_info = {
+ .flags = SMC91X_USE_16BIT | SMC91X_IO_SHIFT_1 | IORESOURCE_IRQ_LOWLEVEL,
+};
+
+static struct resource smc91x_res[] = {
+ [0] = {
+ .start = SMC_IOADDR,
+ .end = SMC_IOADDR + SZ_32 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = ETHERNET_IRQ,
+ .end = ETHERNET_IRQ,
+ .flags = IORESOURCE_IRQ ,
+ }
+};
+
+static struct platform_device smc91x_dev = {
+ .name = "smc91x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(smc91x_res),
+ .resource = smc91x_res,
+
+ .dev = {
+ .platform_data = &smc91x_info,
+ },
+};
+
+/* platform init code */
+static struct platform_device *edosk7705_devices[] __initdata = {
+ &smc91x_dev,
+};
+
+static int __init init_edosk7705_devices(void)
+{
+ return platform_add_devices(edosk7705_devices,
+ ARRAY_SIZE(edosk7705_devices));
+}
+__initcall(init_edosk7705_devices);
+
+/*
+ * The Machine Vector
+ */
+static struct sh_machine_vector mv_edosk7705 __initmv = {
+ .mv_name = "EDOSK7705",
+ .mv_nr_irqs = 80,
+ .mv_init_irq = sh_edosk7705_init_irq,
+};
/*
- * linux/arch/sh/boards/snapgear/setup.c
- *
* Copyright (C) 2002 David McCullough <davidm@snapgear.com>
* Copyright (C) 2003 Paul Mundt <lethal@linux-sh.org>
*
#include <linux/module.h>
#include <linux/sched.h>
#include <asm/machvec.h>
-#include <mach/snapgear.h>
+#include <mach/secureedge5410.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <cpu/timer.h>
+unsigned short secureedge5410_ioport;
+
/*
* EraseConfig handling functions
*/
-
static irqreturn_t eraseconfig_interrupt(int irq, void *dev_id)
{
- (void)__raw_readb(0xb8000000); /* dummy read */
+ ctrl_delay(); /* dummy read */
printk("SnapGear: erase switch interrupt!\n");
static int __init eraseconfig_init(void)
{
+ unsigned int irq = evt2irq(0x240);
+
printk("SnapGear: EraseConfig init\n");
+
/* Setup "EraseConfig" switch on external IRQ 0 */
- if (request_irq(IRL0_IRQ, eraseconfig_interrupt, IRQF_DISABLED,
+ if (request_irq(irq, eraseconfig_interrupt, IRQF_DISABLED,
"Erase Config", NULL))
printk("SnapGear: failed to register IRQ%d for Reset witch\n",
- IRL0_IRQ);
+ irq);
else
printk("SnapGear: registered EraseConfig switch on IRQ%d\n",
- IRL0_IRQ);
- return(0);
+ irq);
+ return 0;
}
-
module_init(eraseconfig_init);
-/****************************************************************************/
/*
* Initialize IRQ setting
*
* IRL2 = eth1
* IRL3 = crypto
*/
-
static void __init init_snapgear_IRQ(void)
{
printk("Setup SnapGear IRQ/IPR ...\n");
static struct sh_machine_vector mv_snapgear __initmv = {
.mv_name = "SnapGear SecureEdge5410",
.mv_nr_irqs = 72,
-
- .mv_inb = snapgear_inb,
- .mv_inw = snapgear_inw,
- .mv_inl = snapgear_inl,
- .mv_outb = snapgear_outb,
- .mv_outw = snapgear_outw,
- .mv_outl = snapgear_outl,
-
- .mv_inb_p = snapgear_inb_p,
- .mv_inw_p = snapgear_inw,
- .mv_inl_p = snapgear_inl,
- .mv_outb_p = snapgear_outb_p,
- .mv_outw_p = snapgear_outw,
- .mv_outl_p = snapgear_outl,
-
.mv_init_irq = init_snapgear_IRQ,
};
+++ /dev/null
-#
-# Makefile for the EDOSK7705 specific parts of the kernel
-#
-
-obj-y := setup.o io.o
+++ /dev/null
-/*
- * arch/sh/boards/renesas/edosk7705/io.c
- *
- * Copyright (C) 2001 Ian da Silva, Jeremy Siegel
- * Based largely on io_se.c.
- *
- * I/O routines for Hitachi EDOSK7705 board.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/io.h>
-#include <mach/edosk7705.h>
-#include <asm/addrspace.h>
-
-#define SMC_IOADDR 0xA2000000
-
-/* Map the Ethernet addresses as if it is at 0x300 - 0x320 */
-static unsigned long sh_edosk7705_isa_port2addr(unsigned long port)
-{
- /*
- * SMC91C96 registers are 4 byte aligned rather than the
- * usual 2 byte!
- */
- if (port >= 0x300 && port < 0x320)
- return SMC_IOADDR + ((port - 0x300) * 2);
-
- maybebadio(port);
- return port;
-}
-
-/* Trying to read / write bytes on odd-byte boundaries to the Ethernet
- * registers causes problems. So we bit-shift the value and read / write
- * in 2 byte chunks. Setting the low byte to 0 does not cause problems
- * now as odd byte writes are only made on the bit mask / interrupt
- * register. This may not be the case in future Mar-2003 SJD
- */
-unsigned char sh_edosk7705_inb(unsigned long port)
-{
- if (port >= 0x300 && port < 0x320 && port & 0x01)
- return __raw_readw(port - 1) >> 8;
-
- return __raw_readb(sh_edosk7705_isa_port2addr(port));
-}
-
-void sh_edosk7705_outb(unsigned char value, unsigned long port)
-{
- if (port >= 0x300 && port < 0x320 && port & 0x01) {
- __raw_writew(((unsigned short)value << 8), port - 1);
- return;
- }
-
- __raw_writeb(value, sh_edosk7705_isa_port2addr(port));
-}
-
-void sh_edosk7705_insb(unsigned long port, void *addr, unsigned long count)
-{
- unsigned char *p = addr;
-
- while (count--)
- *p++ = sh_edosk7705_inb(port);
-}
-
-void sh_edosk7705_outsb(unsigned long port, const void *addr, unsigned long count)
-{
- unsigned char *p = (unsigned char *)addr;
-
- while (count--)
- sh_edosk7705_outb(*p++, port);
-}
+++ /dev/null
-/*
- * arch/sh/boards/renesas/edosk7705/setup.c
- *
- * Copyright (C) 2000 Kazumoto Kojima
- *
- * Hitachi SolutionEngine Support.
- *
- * Modified for edosk7705 development
- * board by S. Dunn, 2003.
- */
-#include <linux/init.h>
-#include <linux/irq.h>
-#include <asm/machvec.h>
-#include <mach/edosk7705.h>
-
-static void __init sh_edosk7705_init_irq(void)
-{
- /* This is the Ethernet interrupt */
- make_imask_irq(0x09);
-}
-
-/*
- * The Machine Vector
- */
-static struct sh_machine_vector mv_edosk7705 __initmv = {
- .mv_name = "EDOSK7705",
- .mv_nr_irqs = 80,
-
- .mv_inb = sh_edosk7705_inb,
- .mv_outb = sh_edosk7705_outb,
-
- .mv_insb = sh_edosk7705_insb,
- .mv_outsb = sh_edosk7705_outsb,
-
- .mv_init_irq = sh_edosk7705_init_irq,
-};
/*
* map I/O ports to memory-mapped addresses
*/
-static unsigned long microdev_isa_port2addr(unsigned long offset)
+void __iomem *microdev_ioport_map(unsigned long offset, unsigned int len)
{
unsigned long result;
* Configuration Registers
*/
result = IO_SUPERIO_PHYS + (offset << 1);
-#if 0
- } else if (offset == KBD_DATA_REG || offset == KBD_CNTL_REG ||
- offset == KBD_STATUS_REG) {
- /*
- * SMSC FDC37C93xAPM SuperIO chip
- *
- * PS/2 Keyboard + Mouse (ports 0x60 and 0x64).
- */
- result = IO_SUPERIO_PHYS + (offset << 1);
-#endif
} else if (((offset >= IO_IDE1_BASE) &&
(offset < IO_IDE1_BASE + IO_IDE_EXTENT)) ||
(offset == IO_IDE1_MISC)) {
result = PVR;
}
- return result;
-}
-
-#define PORT2ADDR(x) (microdev_isa_port2addr(x))
-
-static inline void delay(void)
-{
-#if defined(CONFIG_PCI)
- /* System board present, just make a dummy SRAM access. (CS0 will be
- mapped to PCI memory, probably good to avoid it.) */
- __raw_readw(0xa6800000);
-#else
- /* CS0 will be mapped to flash, ROM etc so safe to access it. */
- __raw_readw(0xa0000000);
-#endif
-}
-
-unsigned char microdev_inb(unsigned long port)
-{
-#ifdef CONFIG_PCI
- if (port >= PCIBIOS_MIN_IO)
- return microdev_pci_inb(port);
-#endif
- return *(volatile unsigned char*)PORT2ADDR(port);
-}
-
-unsigned short microdev_inw(unsigned long port)
-{
-#ifdef CONFIG_PCI
- if (port >= PCIBIOS_MIN_IO)
- return microdev_pci_inw(port);
-#endif
- return *(volatile unsigned short*)PORT2ADDR(port);
-}
-
-unsigned int microdev_inl(unsigned long port)
-{
-#ifdef CONFIG_PCI
- if (port >= PCIBIOS_MIN_IO)
- return microdev_pci_inl(port);
-#endif
- return *(volatile unsigned int*)PORT2ADDR(port);
-}
-
-void microdev_outw(unsigned short b, unsigned long port)
-{
-#ifdef CONFIG_PCI
- if (port >= PCIBIOS_MIN_IO) {
- microdev_pci_outw(b, port);
- return;
- }
-#endif
- *(volatile unsigned short*)PORT2ADDR(port) = b;
-}
-
-void microdev_outb(unsigned char b, unsigned long port)
-{
-#ifdef CONFIG_PCI
- if (port >= PCIBIOS_MIN_IO) {
- microdev_pci_outb(b, port);
- return;
- }
-#endif
-
- /*
- * There is a board feature with the current SH4-202 MicroDev in
- * that the 2 byte enables (nBE0 and nBE1) are tied together (and
- * to the Chip Select Line (Ethernet_CS)). Due to this connectivity,
- * it is not possible to safely perform 8-bit writes to the
- * Ethernet registers, as 16-bits will be consumed from the Data
- * lines (corrupting the other byte). Hence, this function is
- * written to implement 16-bit read/modify/write for all byte-wide
- * accesses.
- *
- * Note: there is no problem with byte READS (even or odd).
- *
- * Sean McGoogan - 16th June 2003.
- */
- if ((port >= IO_LAN91C111_BASE) &&
- (port < IO_LAN91C111_BASE + IO_LAN91C111_EXTENT)) {
- /*
- * Then are trying to perform a byte-write to the
- * LAN91C111. This needs special care.
- */
- if (port % 2 == 1) { /* is the port odd ? */
- /* unset bit-0, i.e. make even */
- const unsigned long evenPort = port-1;
- unsigned short word;
-
- /*
- * do a 16-bit read/write to write to 'port',
- * preserving even byte.
- *
- * Even addresses are bits 0-7
- * Odd addresses are bits 8-15
- */
- word = microdev_inw(evenPort);
- word = (word & 0xffu) | (b << 8);
- microdev_outw(word, evenPort);
- } else {
- /* else, we are trying to do an even byte write */
- unsigned short word;
-
- /*
- * do a 16-bit read/write to write to 'port',
- * preserving odd byte.
- *
- * Even addresses are bits 0-7
- * Odd addresses are bits 8-15
- */
- word = microdev_inw(port);
- word = (word & 0xff00u) | (b);
- microdev_outw(word, port);
- }
- } else {
- *(volatile unsigned char*)PORT2ADDR(port) = b;
- }
-}
-
-void microdev_outl(unsigned int b, unsigned long port)
-{
-#ifdef CONFIG_PCI
- if (port >= PCIBIOS_MIN_IO) {
- microdev_pci_outl(b, port);
- return;
- }
-#endif
- *(volatile unsigned int*)PORT2ADDR(port) = b;
-}
-
-unsigned char microdev_inb_p(unsigned long port)
-{
- unsigned char v = microdev_inb(port);
- delay();
- return v;
-}
-
-unsigned short microdev_inw_p(unsigned long port)
-{
- unsigned short v = microdev_inw(port);
- delay();
- return v;
-}
-
-unsigned int microdev_inl_p(unsigned long port)
-{
- unsigned int v = microdev_inl(port);
- delay();
- return v;
-}
-
-void microdev_outb_p(unsigned char b, unsigned long port)
-{
- microdev_outb(b, port);
- delay();
-}
-
-void microdev_outw_p(unsigned short b, unsigned long port)
-{
- microdev_outw(b, port);
- delay();
-}
-
-void microdev_outl_p(unsigned int b, unsigned long port)
-{
- microdev_outl(b, port);
- delay();
-}
-
-void microdev_insb(unsigned long port, void *buffer, unsigned long count)
-{
- volatile unsigned char *port_addr;
- unsigned char *buf = buffer;
-
- port_addr = (volatile unsigned char *)PORT2ADDR(port);
-
- while (count--)
- *buf++ = *port_addr;
-}
-
-void microdev_insw(unsigned long port, void *buffer, unsigned long count)
-{
- volatile unsigned short *port_addr;
- unsigned short *buf = buffer;
-
- port_addr = (volatile unsigned short *)PORT2ADDR(port);
-
- while (count--)
- *buf++ = *port_addr;
-}
-
-void microdev_insl(unsigned long port, void *buffer, unsigned long count)
-{
- volatile unsigned long *port_addr;
- unsigned int *buf = buffer;
-
- port_addr = (volatile unsigned long *)PORT2ADDR(port);
-
- while (count--)
- *buf++ = *port_addr;
-}
-
-void microdev_outsb(unsigned long port, const void *buffer, unsigned long count)
-{
- volatile unsigned char *port_addr;
- const unsigned char *buf = buffer;
-
- port_addr = (volatile unsigned char *)PORT2ADDR(port);
-
- while (count--)
- *port_addr = *buf++;
-}
-
-void microdev_outsw(unsigned long port, const void *buffer, unsigned long count)
-{
- volatile unsigned short *port_addr;
- const unsigned short *buf = buffer;
-
- port_addr = (volatile unsigned short *)PORT2ADDR(port);
-
- while (count--)
- *port_addr = *buf++;
-}
-
-void microdev_outsl(unsigned long port, const void *buffer, unsigned long count)
-{
- volatile unsigned long *port_addr;
- const unsigned int *buf = buffer;
-
- port_addr = (volatile unsigned long *)PORT2ADDR(port);
-
- while (count--)
- *port_addr = *buf++;
+ return (void __iomem *)result;
}
static struct sh_machine_vector mv_sh4202_microdev __initmv = {
.mv_name = "SH4-202 MicroDev",
.mv_nr_irqs = 72,
-
- .mv_inb = microdev_inb,
- .mv_inw = microdev_inw,
- .mv_inl = microdev_inl,
- .mv_outb = microdev_outb,
- .mv_outw = microdev_outw,
- .mv_outl = microdev_outl,
-
- .mv_inb_p = microdev_inb_p,
- .mv_inw_p = microdev_inw_p,
- .mv_inl_p = microdev_inl_p,
- .mv_outb_p = microdev_outb_p,
- .mv_outw_p = microdev_outw_p,
- .mv_outl_p = microdev_outl_p,
-
- .mv_insb = microdev_insb,
- .mv_insw = microdev_insw,
- .mv_insl = microdev_insl,
- .mv_outsb = microdev_outsb,
- .mv_outsw = microdev_outsw,
- .mv_outsl = microdev_outsl,
-
+ .mv_ioport_map = microdev_ioport_map,
.mv_init_irq = init_microdev_irq,
};
# Makefile for the 7206 SolutionEngine specific parts of the kernel
#
-obj-y := setup.o io.o irq.o
+obj-y := setup.o irq.o
+++ /dev/null
-/* $Id: io.c,v 1.5 2004/02/22 23:08:43 kkojima Exp $
- *
- * linux/arch/sh/boards/se/7206/io.c
- *
- * Copyright (C) 2006 Yoshinori Sato
- *
- * I/O routine for Hitachi 7206 SolutionEngine.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <asm/io.h>
-#include <mach-se/mach/se7206.h>
-
-
-static inline void delay(void)
-{
- __raw_readw(0x20000000); /* P2 ROM Area */
-}
-
-/* MS7750 requires special versions of in*, out* routines, since
- PC-like io ports are located at upper half byte of 16-bit word which
- can be accessed only with 16-bit wide. */
-
-static inline volatile __u16 *
-port2adr(unsigned int port)
-{
- if (port >= 0x2000 && port < 0x2020)
- return (volatile __u16 *) (PA_MRSHPC + (port - 0x2000));
- else if (port >= 0x300 && port < 0x310)
- return (volatile __u16 *) (PA_SMSC + (port - 0x300));
-
- return (volatile __u16 *)port;
-}
-
-unsigned char se7206_inb(unsigned long port)
-{
- return (*port2adr(port)) & 0xff;
-}
-
-unsigned char se7206_inb_p(unsigned long port)
-{
- unsigned long v;
-
- v = (*port2adr(port)) & 0xff;
- delay();
- return v;
-}
-
-unsigned short se7206_inw(unsigned long port)
-{
- return *port2adr(port);
-}
-
-void se7206_outb(unsigned char value, unsigned long port)
-{
- *(port2adr(port)) = value;
-}
-
-void se7206_outb_p(unsigned char value, unsigned long port)
-{
- *(port2adr(port)) = value;
- delay();
-}
-
-void se7206_outw(unsigned short value, unsigned long port)
-{
- *port2adr(port) = value;
-}
-
-void se7206_insb(unsigned long port, void *addr, unsigned long count)
-{
- volatile __u16 *p = port2adr(port);
- __u8 *ap = addr;
-
- while (count--)
- *ap++ = *p;
-}
-
-void se7206_insw(unsigned long port, void *addr, unsigned long count)
-{
- volatile __u16 *p = port2adr(port);
- __u16 *ap = addr;
- while (count--)
- *ap++ = *p;
-}
-
-void se7206_outsb(unsigned long port, const void *addr, unsigned long count)
-{
- volatile __u16 *p = port2adr(port);
- const __u8 *ap = addr;
-
- while (count--)
- *p = *ap++;
-}
-
-void se7206_outsw(unsigned long port, const void *addr, unsigned long count)
-{
- volatile __u16 *p = port2adr(port);
- const __u16 *ap = addr;
- while (count--)
- *p = *ap++;
-}
make_se7206_irq(IRQ0_IRQ); /* SMC91C111 */
make_se7206_irq(IRQ1_IRQ); /* ATA */
make_se7206_irq(IRQ3_IRQ); /* SLOT / PCM */
- __raw_writew(inw(INTC_ICR1) | 0x000b ,INTC_ICR1 ) ; /* ICR1 */
+
+ __raw_writew(__raw_readw(INTC_ICR1) | 0x000b, INTC_ICR); /* ICR1 */
/* FPGA System register setup*/
__raw_writew(0x0000,INTSTS0); /* Clear INTSTS0 */
__raw_writew(0x0000,INTSTS1); /* Clear INTSTS1 */
+
/* IRQ0=LAN, IRQ1=ATA, IRQ3=SLT,PCM */
__raw_writew(0x0001,INTSEL);
}
static struct sh_machine_vector mv_se __initmv = {
.mv_name = "SolutionEngine",
.mv_nr_irqs = 256,
- .mv_inb = se7206_inb,
- .mv_inw = se7206_inw,
- .mv_outb = se7206_outb,
- .mv_outw = se7206_outw,
-
- .mv_inb_p = se7206_inb_p,
- .mv_inw_p = se7206_inw,
- .mv_outb_p = se7206_outb_p,
- .mv_outw_p = se7206_outw,
-
- .mv_insb = se7206_insb,
- .mv_insw = se7206_insw,
- .mv_outsb = se7206_outsb,
- .mv_outsw = se7206_outsw,
-
.mv_init_irq = init_se7206_IRQ,
};
# Makefile for the 770x SolutionEngine specific parts of the kernel
#
-obj-y := setup.o io.o irq.o
+obj-y := setup.o irq.o
+++ /dev/null
-/*
- * Copyright (C) 2000 Kazumoto Kojima
- *
- * I/O routine for Hitachi SolutionEngine.
- */
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <asm/io.h>
-#include <mach-se/mach/se.h>
-
-/* MS7750 requires special versions of in*, out* routines, since
- PC-like io ports are located at upper half byte of 16-bit word which
- can be accessed only with 16-bit wide. */
-
-static inline volatile __u16 *
-port2adr(unsigned int port)
-{
- if (port & 0xff000000)
- return ( volatile __u16 *) port;
- if (port >= 0x2000)
- return (volatile __u16 *) (PA_MRSHPC + (port - 0x2000));
- else if (port >= 0x1000)
- return (volatile __u16 *) (PA_83902 + (port << 1));
- else
- return (volatile __u16 *) (PA_SUPERIO + (port << 1));
-}
-
-static inline int
-shifted_port(unsigned long port)
-{
- /* For IDE registers, value is not shifted */
- if ((0x1f0 <= port && port < 0x1f8) || port == 0x3f6)
- return 0;
- else
- return 1;
-}
-
-unsigned char se_inb(unsigned long port)
-{
- if (shifted_port(port))
- return (*port2adr(port) >> 8);
- else
- return (*port2adr(port))&0xff;
-}
-
-unsigned char se_inb_p(unsigned long port)
-{
- unsigned long v;
-
- if (shifted_port(port))
- v = (*port2adr(port) >> 8);
- else
- v = (*port2adr(port))&0xff;
- ctrl_delay();
- return v;
-}
-
-unsigned short se_inw(unsigned long port)
-{
- if (port >= 0x2000)
- return *port2adr(port);
- else
- maybebadio(port);
- return 0;
-}
-
-unsigned int se_inl(unsigned long port)
-{
- maybebadio(port);
- return 0;
-}
-
-void se_outb(unsigned char value, unsigned long port)
-{
- if (shifted_port(port))
- *(port2adr(port)) = value << 8;
- else
- *(port2adr(port)) = value;
-}
-
-void se_outb_p(unsigned char value, unsigned long port)
-{
- if (shifted_port(port))
- *(port2adr(port)) = value << 8;
- else
- *(port2adr(port)) = value;
- ctrl_delay();
-}
-
-void se_outw(unsigned short value, unsigned long port)
-{
- if (port >= 0x2000)
- *port2adr(port) = value;
- else
- maybebadio(port);
-}
-
-void se_outl(unsigned int value, unsigned long port)
-{
- maybebadio(port);
-}
-
-void se_insb(unsigned long port, void *addr, unsigned long count)
-{
- volatile __u16 *p = port2adr(port);
- __u8 *ap = addr;
-
- if (shifted_port(port)) {
- while (count--)
- *ap++ = *p >> 8;
- } else {
- while (count--)
- *ap++ = *p;
- }
-}
-
-void se_insw(unsigned long port, void *addr, unsigned long count)
-{
- volatile __u16 *p = port2adr(port);
- __u16 *ap = addr;
- while (count--)
- *ap++ = *p;
-}
-
-void se_insl(unsigned long port, void *addr, unsigned long count)
-{
- maybebadio(port);
-}
-
-void se_outsb(unsigned long port, const void *addr, unsigned long count)
-{
- volatile __u16 *p = port2adr(port);
- const __u8 *ap = addr;
-
- if (shifted_port(port)) {
- while (count--)
- *p = *ap++ << 8;
- } else {
- while (count--)
- *p = *ap++;
- }
-}
-
-void se_outsw(unsigned long port, const void *addr, unsigned long count)
-{
- volatile __u16 *p = port2adr(port);
- const __u16 *ap = addr;
-
- while (count--)
- *p = *ap++;
-}
-
-void se_outsl(unsigned long port, const void *addr, unsigned long count)
-{
- maybebadio(port);
-}
#elif defined(CONFIG_CPU_SUBTYPE_SH7710) || defined(CONFIG_CPU_SUBTYPE_SH7712)
.mv_nr_irqs = 104,
#endif
-
- .mv_inb = se_inb,
- .mv_inw = se_inw,
- .mv_inl = se_inl,
- .mv_outb = se_outb,
- .mv_outw = se_outw,
- .mv_outl = se_outl,
-
- .mv_inb_p = se_inb_p,
- .mv_inw_p = se_inw,
- .mv_inl_p = se_inl,
- .mv_outb_p = se_outb_p,
- .mv_outw_p = se_outw,
- .mv_outl_p = se_outl,
-
- .mv_insb = se_insb,
- .mv_insw = se_insw,
- .mv_insl = se_insl,
- .mv_outsb = se_outsb,
- .mv_outsw = se_outsw,
- .mv_outsl = se_outsl,
-
.mv_init_irq = init_se_IRQ,
};
# Makefile for the 7751 SolutionEngine specific parts of the kernel
#
-obj-y := setup.o io.o irq.o
+obj-y := setup.o irq.o
+++ /dev/null
-/*
- * Copyright (C) 2001 Ian da Silva, Jeremy Siegel
- * Based largely on io_se.c.
- *
- * I/O routine for Hitachi 7751 SolutionEngine.
- *
- * Initial version only to support LAN access; some
- * placeholder code from io_se.c left in with the
- * expectation of later SuperIO and PCMCIA access.
- */
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <asm/io.h>
-#include <mach-se/mach/se7751.h>
-#include <asm/addrspace.h>
-
-static inline volatile u16 *port2adr(unsigned int port)
-{
- if (port >= 0x2000)
- return (volatile __u16 *) (PA_MRSHPC + (port - 0x2000));
- maybebadio((unsigned long)port);
- return (volatile __u16*)port;
-}
-
-/*
- * General outline: remap really low stuff [eventually] to SuperIO,
- * stuff in PCI IO space (at or above window at pci.h:PCIBIOS_MIN_IO)
- * is mapped through the PCI IO window. Stuff with high bits (PXSEG)
- * should be way beyond the window, and is used w/o translation for
- * compatibility.
- */
-unsigned char sh7751se_inb(unsigned long port)
-{
- if (PXSEG(port))
- return *(volatile unsigned char *)port;
- else
- return (*port2adr(port)) & 0xff;
-}
-
-unsigned char sh7751se_inb_p(unsigned long port)
-{
- unsigned char v;
-
- if (PXSEG(port))
- v = *(volatile unsigned char *)port;
- else
- v = (*port2adr(port)) & 0xff;
- ctrl_delay();
- return v;
-}
-
-unsigned short sh7751se_inw(unsigned long port)
-{
- if (PXSEG(port))
- return *(volatile unsigned short *)port;
- else if (port >= 0x2000)
- return *port2adr(port);
- else
- maybebadio(port);
- return 0;
-}
-
-unsigned int sh7751se_inl(unsigned long port)
-{
- if (PXSEG(port))
- return *(volatile unsigned long *)port;
- else if (port >= 0x2000)
- return *port2adr(port);
- else
- maybebadio(port);
- return 0;
-}
-
-void sh7751se_outb(unsigned char value, unsigned long port)
-{
-
- if (PXSEG(port))
- *(volatile unsigned char *)port = value;
- else
- *(port2adr(port)) = value;
-}
-
-void sh7751se_outb_p(unsigned char value, unsigned long port)
-{
- if (PXSEG(port))
- *(volatile unsigned char *)port = value;
- else
- *(port2adr(port)) = value;
- ctrl_delay();
-}
-
-void sh7751se_outw(unsigned short value, unsigned long port)
-{
- if (PXSEG(port))
- *(volatile unsigned short *)port = value;
- else if (port >= 0x2000)
- *port2adr(port) = value;
- else
- maybebadio(port);
-}
-
-void sh7751se_outl(unsigned int value, unsigned long port)
-{
- if (PXSEG(port))
- *(volatile unsigned long *)port = value;
- else
- maybebadio(port);
-}
-
-void sh7751se_insl(unsigned long port, void *addr, unsigned long count)
-{
- maybebadio(port);
-}
-
-void sh7751se_outsl(unsigned long port, const void *addr, unsigned long count)
-{
- maybebadio(port);
-}
static struct sh_machine_vector mv_7751se __initmv = {
.mv_name = "7751 SolutionEngine",
.mv_nr_irqs = 72,
-
- .mv_inb = sh7751se_inb,
- .mv_inw = sh7751se_inw,
- .mv_inl = sh7751se_inl,
- .mv_outb = sh7751se_outb,
- .mv_outw = sh7751se_outw,
- .mv_outl = sh7751se_outl,
-
- .mv_inb_p = sh7751se_inb_p,
- .mv_inw_p = sh7751se_inw,
- .mv_inl_p = sh7751se_inl,
- .mv_outb_p = sh7751se_outb_p,
- .mv_outw_p = sh7751se_outw,
- .mv_outl_p = sh7751se_outl,
-
- .mv_insl = sh7751se_insl,
- .mv_outsl = sh7751se_outsl,
-
.mv_init_irq = init_7751se_IRQ,
};
+++ /dev/null
-#
-# Makefile for the SnapGear specific parts of the kernel
-#
-
-obj-y := setup.o io.o
+++ /dev/null
-/*
- * Copyright (C) 2002 David McCullough <davidm@snapgear.com>
- * Copyright (C) 2001 Ian da Silva, Jeremy Siegel
- * Based largely on io_se.c.
- *
- * I/O routine for Hitachi 7751 SolutionEngine.
- *
- * Initial version only to support LAN access; some
- * placeholder code from io_se.c left in with the
- * expectation of later SuperIO and PCMCIA access.
- */
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <asm/io.h>
-#include <asm/addrspace.h>
-
-#ifdef CONFIG_SH_SECUREEDGE5410
-unsigned short secureedge5410_ioport;
-#endif
-
-static inline volatile __u16 *port2adr(unsigned int port)
-{
- maybebadio((unsigned long)port);
- return (volatile __u16*)port;
-}
-
-/*
- * General outline: remap really low stuff [eventually] to SuperIO,
- * stuff in PCI IO space (at or above window at pci.h:PCIBIOS_MIN_IO)
- * is mapped through the PCI IO window. Stuff with high bits (PXSEG)
- * should be way beyond the window, and is used w/o translation for
- * compatibility.
- */
-unsigned char snapgear_inb(unsigned long port)
-{
- if (PXSEG(port))
- return *(volatile unsigned char *)port;
- else
- return (*port2adr(port)) & 0xff;
-}
-
-unsigned char snapgear_inb_p(unsigned long port)
-{
- unsigned char v;
-
- if (PXSEG(port))
- v = *(volatile unsigned char *)port;
- else
- v = (*port2adr(port))&0xff;
- ctrl_delay();
- return v;
-}
-
-unsigned short snapgear_inw(unsigned long port)
-{
- if (PXSEG(port))
- return *(volatile unsigned short *)port;
- else if (port >= 0x2000)
- return *port2adr(port);
- else
- maybebadio(port);
- return 0;
-}
-
-unsigned int snapgear_inl(unsigned long port)
-{
- if (PXSEG(port))
- return *(volatile unsigned long *)port;
- else if (port >= 0x2000)
- return *port2adr(port);
- else
- maybebadio(port);
- return 0;
-}
-
-void snapgear_outb(unsigned char value, unsigned long port)
-{
-
- if (PXSEG(port))
- *(volatile unsigned char *)port = value;
- else
- *(port2adr(port)) = value;
-}
-
-void snapgear_outb_p(unsigned char value, unsigned long port)
-{
- if (PXSEG(port))
- *(volatile unsigned char *)port = value;
- else
- *(port2adr(port)) = value;
- ctrl_delay();
-}
-
-void snapgear_outw(unsigned short value, unsigned long port)
-{
- if (PXSEG(port))
- *(volatile unsigned short *)port = value;
- else if (port >= 0x2000)
- *port2adr(port) = value;
- else
- maybebadio(port);
-}
-
-void snapgear_outl(unsigned int value, unsigned long port)
-{
- if (PXSEG(port))
- *(volatile unsigned long *)port = value;
- else
- maybebadio(port);
-}
-
-void snapgear_insl(unsigned long port, void *addr, unsigned long count)
-{
- maybebadio(port);
-}
-
-void snapgear_outsl(unsigned long port, const void *addr, unsigned long count)
-{
- maybebadio(port);
-}
+++ /dev/null
-#
-# Makefile for the SystemH specific parts of the kernel
-#
-
-obj-y := setup.o irq.o io.o
-
-# XXX: This wants to be consolidated in arch/sh/drivers/pci, and more
-# importantly, with the generic sh7751_pcic_init() code. For now, we'll
-# just abuse the hell out of kbuild, because we can..
-
-obj-$(CONFIG_PCI) += pci.o
-pci-y := ../../se/7751/pci.o
-
+++ /dev/null
-/*
- * linux/arch/sh/boards/renesas/systemh/io.c
- *
- * Copyright (C) 2001 Ian da Silva, Jeremy Siegel
- * Based largely on io_se.c.
- *
- * I/O routine for Hitachi 7751 Systemh.
- */
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <mach/systemh7751.h>
-#include <asm/addrspace.h>
-#include <asm/io.h>
-
-#define ETHER_IOMAP(adr) (0xB3000000 + (adr)) /*map to 16bits access area
- of smc lan chip*/
-static inline volatile __u16 *
-port2adr(unsigned int port)
-{
- if (port >= 0x2000)
- return (volatile __u16 *) (PA_MRSHPC + (port - 0x2000));
- maybebadio((unsigned long)port);
- return (volatile __u16*)port;
-}
-
-/*
- * General outline: remap really low stuff [eventually] to SuperIO,
- * stuff in PCI IO space (at or above window at pci.h:PCIBIOS_MIN_IO)
- * is mapped through the PCI IO window. Stuff with high bits (PXSEG)
- * should be way beyond the window, and is used w/o translation for
- * compatibility.
- */
-unsigned char sh7751systemh_inb(unsigned long port)
-{
- if (PXSEG(port))
- return *(volatile unsigned char *)port;
- else if (port <= 0x3F1)
- return *(volatile unsigned char *)ETHER_IOMAP(port);
- else
- return (*port2adr(port))&0xff;
-}
-
-unsigned char sh7751systemh_inb_p(unsigned long port)
-{
- unsigned char v;
-
- if (PXSEG(port))
- v = *(volatile unsigned char *)port;
- else if (port <= 0x3F1)
- v = *(volatile unsigned char *)ETHER_IOMAP(port);
- else
- v = (*port2adr(port))&0xff;
- ctrl_delay();
- return v;
-}
-
-unsigned short sh7751systemh_inw(unsigned long port)
-{
- if (PXSEG(port))
- return *(volatile unsigned short *)port;
- else if (port >= 0x2000)
- return *port2adr(port);
- else if (port <= 0x3F1)
- return *(volatile unsigned int *)ETHER_IOMAP(port);
- else
- maybebadio(port);
- return 0;
-}
-
-unsigned int sh7751systemh_inl(unsigned long port)
-{
- if (PXSEG(port))
- return *(volatile unsigned long *)port;
- else if (port >= 0x2000)
- return *port2adr(port);
- else if (port <= 0x3F1)
- return *(volatile unsigned int *)ETHER_IOMAP(port);
- else
- maybebadio(port);
- return 0;
-}
-
-void sh7751systemh_outb(unsigned char value, unsigned long port)
-{
-
- if (PXSEG(port))
- *(volatile unsigned char *)port = value;
- else if (port <= 0x3F1)
- *(volatile unsigned char *)ETHER_IOMAP(port) = value;
- else
- *(port2adr(port)) = value;
-}
-
-void sh7751systemh_outb_p(unsigned char value, unsigned long port)
-{
- if (PXSEG(port))
- *(volatile unsigned char *)port = value;
- else if (port <= 0x3F1)
- *(volatile unsigned char *)ETHER_IOMAP(port) = value;
- else
- *(port2adr(port)) = value;
- ctrl_delay();
-}
-
-void sh7751systemh_outw(unsigned short value, unsigned long port)
-{
- if (PXSEG(port))
- *(volatile unsigned short *)port = value;
- else if (port >= 0x2000)
- *port2adr(port) = value;
- else if (port <= 0x3F1)
- *(volatile unsigned short *)ETHER_IOMAP(port) = value;
- else
- maybebadio(port);
-}
-
-void sh7751systemh_outl(unsigned int value, unsigned long port)
-{
- if (PXSEG(port))
- *(volatile unsigned long *)port = value;
- else
- maybebadio(port);
-}
-
-void sh7751systemh_insb(unsigned long port, void *addr, unsigned long count)
-{
- unsigned char *p = addr;
- while (count--) *p++ = sh7751systemh_inb(port);
-}
-
-void sh7751systemh_insw(unsigned long port, void *addr, unsigned long count)
-{
- unsigned short *p = addr;
- while (count--) *p++ = sh7751systemh_inw(port);
-}
-
-void sh7751systemh_insl(unsigned long port, void *addr, unsigned long count)
-{
- maybebadio(port);
-}
-
-void sh7751systemh_outsb(unsigned long port, const void *addr, unsigned long count)
-{
- unsigned char *p = (unsigned char*)addr;
- while (count--) sh7751systemh_outb(*p++, port);
-}
-
-void sh7751systemh_outsw(unsigned long port, const void *addr, unsigned long count)
-{
- unsigned short *p = (unsigned short*)addr;
- while (count--) sh7751systemh_outw(*p++, port);
-}
-
-void sh7751systemh_outsl(unsigned long port, const void *addr, unsigned long count)
-{
- maybebadio(port);
-}
+++ /dev/null
-/*
- * linux/arch/sh/boards/renesas/systemh/irq.c
- *
- * Copyright (C) 2000 Kazumoto Kojima
- *
- * Hitachi SystemH Support.
- *
- * Modified for 7751 SystemH by
- * Jonathan Short.
- */
-
-#include <linux/init.h>
-#include <linux/irq.h>
-#include <linux/interrupt.h>
-#include <linux/io.h>
-
-#include <mach/systemh7751.h>
-#include <asm/smc37c93x.h>
-
-/* address of external interrupt mask register
- * address must be set prior to use these (maybe in init_XXX_irq())
- * XXX : is it better to use .config than specifying it in code? */
-static unsigned long *systemh_irq_mask_register = (unsigned long *)0xB3F10004;
-static unsigned long *systemh_irq_request_register = (unsigned long *)0xB3F10000;
-
-static void disable_systemh_irq(struct irq_data *data)
-{
- unsigned long val, mask = 0x01 << 1;
-
- /* Clear the "irq"th bit in the mask and set it in the request */
- val = __raw_readl((unsigned long)systemh_irq_mask_register);
- val &= ~mask;
- __raw_writel(val, (unsigned long)systemh_irq_mask_register);
-
- val = __raw_readl((unsigned long)systemh_irq_request_register);
- val |= mask;
- __raw_writel(val, (unsigned long)systemh_irq_request_register);
-}
-
-static void enable_systemh_irq(struct irq_data *data)
-{
- unsigned long val, mask = 0x01 << 1;
-
- /* Set "irq"th bit in the mask register */
- val = __raw_readl((unsigned long)systemh_irq_mask_register);
- val |= mask;
- __raw_writel(val, (unsigned long)systemh_irq_mask_register);
-}
-
-static struct irq_chip systemh_irq_type = {
- .name = "SystemH Register",
- .irq_unmask = enable_systemh_irq,
- .irq_mask = disable_systemh_irq,
-};
-
-void make_systemh_irq(unsigned int irq)
-{
- disable_irq_nosync(irq);
- set_irq_chip_and_handler(irq, &systemh_irq_type, handle_level_irq);
- disable_systemh_irq(irq_get_irq_data(irq));
-}
+++ /dev/null
-/*
- * linux/arch/sh/boards/renesas/systemh/setup.c
- *
- * Copyright (C) 2000 Kazumoto Kojima
- * Copyright (C) 2003 Paul Mundt
- *
- * Hitachi SystemH Support.
- *
- * Modified for 7751 SystemH by Jonathan Short.
- *
- * Rewritten for 2.6 by Paul Mundt.
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-#include <linux/init.h>
-#include <asm/machvec.h>
-#include <mach/systemh7751.h>
-
-extern void make_systemh_irq(unsigned int irq);
-
-/*
- * Initialize IRQ setting
- */
-static void __init sh7751systemh_init_irq(void)
-{
- make_systemh_irq(0xb); /* Ethernet interrupt */
-}
-
-static struct sh_machine_vector mv_7751systemh __initmv = {
- .mv_name = "7751 SystemH",
- .mv_nr_irqs = 72,
-
- .mv_inb = sh7751systemh_inb,
- .mv_inw = sh7751systemh_inw,
- .mv_inl = sh7751systemh_inl,
- .mv_outb = sh7751systemh_outb,
- .mv_outw = sh7751systemh_outw,
- .mv_outl = sh7751systemh_outl,
-
- .mv_inb_p = sh7751systemh_inb_p,
- .mv_inw_p = sh7751systemh_inw,
- .mv_inl_p = sh7751systemh_inl,
- .mv_outb_p = sh7751systemh_outb_p,
- .mv_outw_p = sh7751systemh_outw,
- .mv_outl_p = sh7751systemh_outl,
-
- .mv_insb = sh7751systemh_insb,
- .mv_insw = sh7751systemh_insw,
- .mv_insl = sh7751systemh_insl,
- .mv_outsb = sh7751systemh_outsb,
- .mv_outsw = sh7751systemh_outsw,
- .mv_outsl = sh7751systemh_outsl,
-
- .mv_init_irq = sh7751systemh_init_irq,
-};
+++ /dev/null
-CONFIG_EXPERIMENTAL=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
-# CONFIG_SYSCTL_SYSCALL is not set
-# CONFIG_HOTPLUG is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_CPU_SUBTYPE_SH7751R=y
-CONFIG_MEMORY_START=0x0c000000
-CONFIG_MEMORY_SIZE=0x00400000
-CONFIG_FLATMEM_MANUAL=y
-CONFIG_SH_7751_SYSTEMH=y
-CONFIG_PREEMPT=y
-# CONFIG_STANDALONE is not set
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=1024
-# CONFIG_INPUT is not set
-# CONFIG_SERIO_SERPORT is not set
-# CONFIG_VT is not set
-CONFIG_HW_RANDOM=y
-CONFIG_PROC_KCORE=y
-CONFIG_TMPFS=y
-CONFIG_CRAMFS=y
-CONFIG_ROMFS_FS=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
/*
* These will never work in 32-bit, don't even bother.
*/
-#define P1SEGADDR(a) __futile_remapping_attempt
-#define P2SEGADDR(a) __futile_remapping_attempt
-#define P3SEGADDR(a) __futile_remapping_attempt
-#define P4SEGADDR(a) __futile_remapping_attempt
+#define P1SEGADDR(a) ({ (void)(a); BUG(); NULL; })
+#define P2SEGADDR(a) ({ (void)(a); BUG(); NULL; })
+#define P3SEGADDR(a) ({ (void)(a); BUG(); NULL; })
+#define P4SEGADDR(a) ({ (void)(a); BUG(); NULL; })
#endif
#endif /* P1SEG */
#define PHYS_ADDR_MASK29 0x1fffffff
#define PHYS_ADDR_MASK32 0xffffffff
-#ifdef CONFIG_PMB
static inline unsigned long phys_addr_mask(void)
{
/* Is the MMU in 29bit mode? */
return PHYS_ADDR_MASK32;
}
-#elif defined(CONFIG_32BIT)
-static inline unsigned long phys_addr_mask(void)
-{
- return PHYS_ADDR_MASK32;
-}
-#else
-static inline unsigned long phys_addr_mask(void)
-{
- return PHYS_ADDR_MASK29;
-}
-#endif
#define PTE_PHYS_MASK (phys_addr_mask() & PAGE_MASK)
#define PTE_FLAGS_MASK (~(PTE_PHYS_MASK) << PAGE_SHIFT)
#include <linux/compiler.h>
#include <linux/linkage.h>
#include <asm/types.h>
+#include <asm/uncached.h>
#define AT_VECTOR_SIZE_ARCH 5 /* entries in ARCH_DLINFO */
#define instruction_size(insn) (4)
#endif
-extern unsigned long cached_to_uncached;
-extern unsigned long uncached_size;
-
void per_cpu_trap_init(void);
void default_idle(void);
void cpu_idle_wait(void);
__restore_dsp(prev); \
} while (0)
-/*
- * Jump to uncached area.
- * When handling TLB or caches, we need to do it from an uncached area.
- */
-#define jump_to_uncached() \
-do { \
- unsigned long __dummy; \
- \
- __asm__ __volatile__( \
- "mova 1f, %0\n\t" \
- "add %1, %0\n\t" \
- "jmp @%0\n\t" \
- " nop\n\t" \
- ".balign 4\n" \
- "1:" \
- : "=&z" (__dummy) \
- : "r" (cached_to_uncached)); \
-} while (0)
-
-/*
- * Back to cached area.
- */
-#define back_to_cached() \
-do { \
- unsigned long __dummy; \
- ctrl_barrier(); \
- __asm__ __volatile__( \
- "mov.l 1f, %0\n\t" \
- "jmp @%0\n\t" \
- " nop\n\t" \
- ".balign 4\n" \
- "1: .long 2f\n" \
- "2:" \
- : "=&r" (__dummy)); \
-} while (0)
-
#ifdef CONFIG_CPU_HAS_SR_RB
#define lookup_exception_vector() \
({ \
&next->thread); \
} while (0)
-#define jump_to_uncached() do { } while (0)
-#define back_to_cached() do { } while (0)
-
#define __icbi(addr) __asm__ __volatile__ ( "icbi %0, 0\n\t" : : "r" (addr))
#define __ocbp(addr) __asm__ __volatile__ ( "ocbp %0, 0\n\t" : : "r" (addr))
#define __ocbi(addr) __asm__ __volatile__ ( "ocbi %0, 0\n\t" : : "r" (addr))
#include <linux/bug.h>
#ifdef CONFIG_UNCACHED_MAPPING
+extern unsigned long cached_to_uncached;
+extern unsigned long uncached_size;
extern unsigned long uncached_start, uncached_end;
extern int virt_addr_uncached(unsigned long kaddr);
extern void uncached_init(void);
extern void uncached_resize(unsigned long size);
+
+/*
+ * Jump to uncached area.
+ * When handling TLB or caches, we need to do it from an uncached area.
+ */
+#define jump_to_uncached() \
+do { \
+ unsigned long __dummy; \
+ \
+ __asm__ __volatile__( \
+ "mova 1f, %0\n\t" \
+ "add %1, %0\n\t" \
+ "jmp @%0\n\t" \
+ " nop\n\t" \
+ ".balign 4\n" \
+ "1:" \
+ : "=&z" (__dummy) \
+ : "r" (cached_to_uncached)); \
+} while (0)
+
+/*
+ * Back to cached area.
+ */
+#define back_to_cached() \
+do { \
+ unsigned long __dummy; \
+ ctrl_barrier(); \
+ __asm__ __volatile__( \
+ "mov.l 1f, %0\n\t" \
+ "jmp @%0\n\t" \
+ " nop\n\t" \
+ ".balign 4\n" \
+ "1: .long 2f\n" \
+ "2:" \
+ : "=&r" (__dummy)); \
+} while (0)
#else
#define virt_addr_uncached(kaddr) (0)
#define uncached_init() do { } while (0)
#define uncached_resize(size) BUG()
+#define jump_to_uncached() do { } while (0)
+#define back_to_cached() do { } while (0)
#endif
#endif /* __ASM_SH_UNCACHED_H */
+++ /dev/null
-#ifndef __ASM_SH_EDOSK7705_H
-#define __ASM_SH_EDOSK7705_H
-
-#define __IO_PREFIX sh_edosk7705
-#include <asm/io_generic.h>
-
-#endif /* __ASM_SH_EDOSK7705_H */
#define __IO_PREFIX microdev
#include <asm/io_generic.h>
-#if defined(CONFIG_PCI)
-unsigned char microdev_pci_inb(unsigned long port);
-unsigned short microdev_pci_inw(unsigned long port);
-unsigned long microdev_pci_inl(unsigned long port);
-void microdev_pci_outb(unsigned char data, unsigned long port);
-void microdev_pci_outw(unsigned short data, unsigned long port);
-void microdev_pci_outl(unsigned long data, unsigned long port);
-#endif
-
#endif /* __ASM_SH_MICRODEV_H */
#ifndef _ASM_SH_IO_SNAPGEAR_H
#define _ASM_SH_IO_SNAPGEAR_H
-#if defined(CONFIG_CPU_SH4)
-/*
- * The external interrupt lines, these take up ints 0 - 15 inclusive
- * depending on the priority for the interrupt. In fact the priority
- * is the interrupt :-)
- */
-
-#define IRL0_IRQ 2
-#define IRL0_PRIORITY 13
-
-#define IRL1_IRQ 5
-#define IRL1_PRIORITY 10
-
-#define IRL2_IRQ 8
-#define IRL2_PRIORITY 7
-
-#define IRL3_IRQ 11
-#define IRL3_PRIORITY 4
-#endif
-
#define __IO_PREFIX snapgear
#include <asm/io_generic.h>
-#ifdef CONFIG_SH_SECUREEDGE5410
/*
* We need to remember what was written to the ioport as some bits
* are shared with other functions and you cannot read back what was
((secureedge5410_ioport & ~(mask)) | ((val) & (mask)))))
#define SECUREEDGE_READ_IOPORT() \
((*SECUREEDGE_IOPORT_ADDR&0x0817) | (secureedge5410_ioport&~0x0817))
-#endif
#endif /* _ASM_SH_IO_SNAPGEAR_H */
+++ /dev/null
-#ifndef __ASM_SH_SYSTEMH_7751SYSTEMH_H
-#define __ASM_SH_SYSTEMH_7751SYSTEMH_H
-
-/*
- * linux/include/asm-sh/systemh/7751systemh.h
- *
- * Copyright (C) 2000 Kazumoto Kojima
- *
- * Hitachi SystemH support
-
- * Modified for 7751 SystemH by
- * Jonathan Short, 2002.
- */
-
-/* Box specific addresses. */
-
-#define PA_ROM 0x00000000 /* EPROM */
-#define PA_ROM_SIZE 0x00400000 /* EPROM size 4M byte */
-#define PA_FROM 0x01000000 /* EPROM */
-#define PA_FROM_SIZE 0x00400000 /* EPROM size 4M byte */
-#define PA_EXT1 0x04000000
-#define PA_EXT1_SIZE 0x04000000
-#define PA_EXT2 0x08000000
-#define PA_EXT2_SIZE 0x04000000
-#define PA_SDRAM 0x0c000000
-#define PA_SDRAM_SIZE 0x04000000
-
-#define PA_EXT4 0x12000000
-#define PA_EXT4_SIZE 0x02000000
-#define PA_EXT5 0x14000000
-#define PA_EXT5_SIZE 0x04000000
-#define PA_PCIC 0x18000000 /* MR-SHPC-01 PCMCIA */
-
-#define PA_DIPSW0 0xb9000000 /* Dip switch 5,6 */
-#define PA_DIPSW1 0xb9000002 /* Dip switch 7,8 */
-#define PA_LED 0xba000000 /* LED */
-#define PA_BCR 0xbb000000 /* FPGA on the MS7751SE01 */
-
-#define PA_MRSHPC 0xb83fffe0 /* MR-SHPC-01 PCMCIA controller */
-#define PA_MRSHPC_MW1 0xb8400000 /* MR-SHPC-01 memory window base */
-#define PA_MRSHPC_MW2 0xb8500000 /* MR-SHPC-01 attribute window base */
-#define PA_MRSHPC_IO 0xb8600000 /* MR-SHPC-01 I/O window base */
-#define MRSHPC_MODE (PA_MRSHPC + 4)
-#define MRSHPC_OPTION (PA_MRSHPC + 6)
-#define MRSHPC_CSR (PA_MRSHPC + 8)
-#define MRSHPC_ISR (PA_MRSHPC + 10)
-#define MRSHPC_ICR (PA_MRSHPC + 12)
-#define MRSHPC_CPWCR (PA_MRSHPC + 14)
-#define MRSHPC_MW0CR1 (PA_MRSHPC + 16)
-#define MRSHPC_MW1CR1 (PA_MRSHPC + 18)
-#define MRSHPC_IOWCR1 (PA_MRSHPC + 20)
-#define MRSHPC_MW0CR2 (PA_MRSHPC + 22)
-#define MRSHPC_MW1CR2 (PA_MRSHPC + 24)
-#define MRSHPC_IOWCR2 (PA_MRSHPC + 26)
-#define MRSHPC_CDCR (PA_MRSHPC + 28)
-#define MRSHPC_PCIC_INFO (PA_MRSHPC + 30)
-
-#define BCR_ILCRA (PA_BCR + 0)
-#define BCR_ILCRB (PA_BCR + 2)
-#define BCR_ILCRC (PA_BCR + 4)
-#define BCR_ILCRD (PA_BCR + 6)
-#define BCR_ILCRE (PA_BCR + 8)
-#define BCR_ILCRF (PA_BCR + 10)
-#define BCR_ILCRG (PA_BCR + 12)
-
-#define IRQ_79C973 13
-
-#define __IO_PREFIX sh7751systemh
-#include <asm/io_generic.h>
-
-#endif /* __ASM_SH_SYSTEMH_7751SYSTEMH_H */
* Default rate for the root input clock, reset this with clk_set_rate()
* from the platform code.
*/
-struct clk extal_clk = {
+static struct clk extal_clk = {
.rate = 33333333,
};
.parent = &pll_clk,
};
-struct clk *main_clks[] = {
+static struct clk *main_clks[] = {
&r_clk,
&extal_clk,
&fll_clk,
enum { DIV6_V, DIV6_FA, DIV6_FB, DIV6_I, DIV6_S, DIV6_NR };
-struct clk div6_clks[DIV6_NR] = {
+static struct clk div6_clks[DIV6_NR] = {
[DIV6_V] = SH_CLK_DIV6(&div3_clk, VCLKCR, 0),
[DIV6_FA] = SH_CLK_DIV6(&div3_clk, FCLKACR, 0),
[DIV6_FB] = SH_CLK_DIV6(&div3_clk, FCLKBCR, 0),
config 32BIT
bool
- default y if CPU_SH5
+ default y if CPU_SH5 || !MMU
config PMB
bool "Support 32-bit physical addressing through PMB"
void dma_cache_sync(struct device *dev, void *vaddr, size_t size,
enum dma_data_direction direction)
{
-#if defined(CONFIG_CPU_SH5) || defined(CONFIG_PMB)
- void *p1addr = vaddr;
-#else
- void *p1addr = (void*) P1SEGADDR((unsigned long)vaddr);
-#endif
+ void *addr;
+
+ addr = __in_29bit_mode() ?
+ (void *)P1SEGADDR((unsigned long)vaddr) : vaddr;
switch (direction) {
case DMA_FROM_DEVICE: /* invalidate only */
- __flush_invalidate_region(p1addr, size);
+ __flush_invalidate_region(addr, size);
break;
case DMA_TO_DEVICE: /* writeback only */
- __flush_wback_region(p1addr, size);
+ __flush_wback_region(addr, size);
break;
case DMA_BIDIRECTIONAL: /* writeback and invalidate */
- __flush_purge_region(p1addr, size);
+ __flush_purge_region(addr, size);
break;
default:
BUG();
void __init uncached_init(void)
{
-#ifdef CONFIG_29BIT
+#if defined(CONFIG_29BIT) || !defined(CONFIG_MMU)
uncached_start = P2SEG;
#else
uncached_start = memory_end;
7724SE SH_7724_SOLUTION_ENGINE
7751SE SH_7751_SOLUTION_ENGINE
7780SE SH_7780_SOLUTION_ENGINE
-7751SYSTEMH SH_7751_SYSTEMH
HP6XX SH_HP6XX
DREAMCAST SH_DREAMCAST
SNAPGEAR SH_SECUREEDGE5410
#ifdef CONFIG_SH_SECUREEDGE5410
#include <asm/rtc.h>
-#include <mach/snapgear.h>
+#include <mach/secureedge5410.h>
#define RTC_RESET 0x1000
#define RTC_IODATA 0x0800
static long clk_rate_round_helper(struct clk_rate_round_data *rounder)
{
unsigned long rate_error, rate_error_prev = ~0UL;
- unsigned long rate_best_fit = rounder->rate;
unsigned long highest, lowest, freq;
+ long rate_best_fit = -ENOENT;
int i;
highest = 0;
};
if (clk->nr_freqs < 1)
- return 0;
+ return -ENOSYS;
return clk_rate_round_helper(&table_round);
}
}
EXPORT_SYMBOL_GPL(clk_round_rate);
+long clk_round_parent(struct clk *clk, unsigned long target,
+ unsigned long *best_freq, unsigned long *parent_freq,
+ unsigned int div_min, unsigned int div_max)
+{
+ struct cpufreq_frequency_table *freq, *best = NULL;
+ unsigned long error = ULONG_MAX, freq_high, freq_low, div;
+ struct clk *parent = clk_get_parent(clk);
+
+ if (!parent) {
+ *parent_freq = 0;
+ *best_freq = clk_round_rate(clk, target);
+ return abs(target - *best_freq);
+ }
+
+ for (freq = parent->freq_table; freq->frequency != CPUFREQ_TABLE_END;
+ freq++) {
+ if (freq->frequency == CPUFREQ_ENTRY_INVALID)
+ continue;
+
+ if (unlikely(freq->frequency / target <= div_min - 1)) {
+ unsigned long freq_max;
+
+ freq_max = (freq->frequency + div_min / 2) / div_min;
+ if (error > target - freq_max) {
+ error = target - freq_max;
+ best = freq;
+ if (best_freq)
+ *best_freq = freq_max;
+ }
+
+ pr_debug("too low freq %lu, error %lu\n", freq->frequency,
+ target - freq_max);
+
+ if (!error)
+ break;
+
+ continue;
+ }
+
+ if (unlikely(freq->frequency / target >= div_max)) {
+ unsigned long freq_min;
+
+ freq_min = (freq->frequency + div_max / 2) / div_max;
+ if (error > freq_min - target) {
+ error = freq_min - target;
+ best = freq;
+ if (best_freq)
+ *best_freq = freq_min;
+ }
+
+ pr_debug("too high freq %lu, error %lu\n", freq->frequency,
+ freq_min - target);
+
+ if (!error)
+ break;
+
+ continue;
+ }
+
+ div = freq->frequency / target;
+ freq_high = freq->frequency / div;
+ freq_low = freq->frequency / (div + 1);
+
+ if (freq_high - target < error) {
+ error = freq_high - target;
+ best = freq;
+ if (best_freq)
+ *best_freq = freq_high;
+ }
+
+ if (target - freq_low < error) {
+ error = target - freq_low;
+ best = freq;
+ if (best_freq)
+ *best_freq = freq_low;
+ }
+
+ pr_debug("%u / %lu = %lu, / %lu = %lu, best %lu, parent %u\n",
+ freq->frequency, div, freq_high, div + 1, freq_low,
+ *best_freq, best->frequency);
+
+ if (!error)
+ break;
+ }
+
+ if (parent_freq)
+ *parent_freq = best->frequency;
+
+ return error;
+}
+EXPORT_SYMBOL_GPL(clk_round_parent);
+
#ifdef CONFIG_PM
static int clks_sysdev_suspend(struct sys_device *dev, pm_message_t state)
{
* Register the IRQ position with the global IRQ map, then insert
* it in to the radix tree.
*/
- irq_reserve_irqs(irq, 1);
+ irq_reserve_irq(irq);
raw_spin_lock_irqsave(&intc_big_lock, flags);
radix_tree_insert(&d->tree, enum_id, intc_irq_xlate_get(irq));
int i;
for (i = 0; i < nr_vecs; i++)
- irq_reserve_irqs(evt2irq(vectors[i].vect), 1);
+ irq_reserve_irq(evt2irq(vectors[i].vect));
}
long clk_rate_div_range_round(struct clk *clk, unsigned int div_min,
unsigned int div_max, unsigned long rate);
+long clk_round_parent(struct clk *clk, unsigned long target,
+ unsigned long *best_freq, unsigned long *parent_freq,
+ unsigned int div_min, unsigned int div_max);
+
#define SH_CLK_MSTP32(_parent, _enable_reg, _enable_bit, _flags) \
{ \
.parent = _parent, \
git://bbs.cooldavid.org / net-next-2.6.git / commitdiff