ath9k has a race on putting the chip into network sleep and
having registers read from hardware. The race occurs because
although ath9k_ps_restore() locks its own callers it makes use
of some variables which get altered in the driver at different
code paths. The variables are the ps_enabled and ps_flags.
This is easily reprodicible in large network environments when
roaming with the wpa_supplicant simple bgscan. You'd get some
0xdeadbeef read out on certain registers such as:
ath: timeout (100000 us) on reg 0x806c: 0xdeadbeef & 0x01f00000 != 0x00000000
ath: RX failed to go idle in 10 ms RXSM=0xdeadbeef
The fix is to protect the ath9k_config(hw, IEEE80211_CONF_CHANGE_PS)
calls with a spin_lock_irqsave() which will disable contendors for
these variables from interrupt context, timers, re-entry from mac80211
on the same callback, and most importantly from ath9k_ps_restore()
which is the only call which will put the device into network sleep.
There are quite a few threads and bug reports on these a few of them are:
Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Cc: Amod Bodas <amod.bodas@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
To optimize register read/write operations, the HTC firmwares were patched
to change EP3 and EP4 pipe types from Interrupt to Bulk. So register writes
are submitted as bulk urbs, but register reads are not. Also changing the
register read endpoint pipe as bulk type when URBs are filled improves the
register reads considerably which results in reduced scan time and CPU
utilization.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 16 Sep 2010 12:58:23 +0000 (14:58 +0200)]
mac80211: add p2p device type support
When a driver advertises p2p device support,
mac80211 will handle it, but internally it will
rewrite the interface type to STA/AP rather than
P2P-STA/GO since otherwise a lot of paths need
to be touched that are otherwise identical. A
p2p boolean tells drivers whether or not a given
interface will be used for p2p or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw: remove warning in ath9k_hw_def_get_num_ant_config
This patch fixes following warning
drivers/net/wireless/ath/ath9k/eeprom_def.c: In function 'ath9k_hw_def_get_num_ant_config'
drivers/net/wireless/ath/ath9k/eeprom_def.c:1425:47: warning: comparison
between 'enum ath9k_hal_freq_band' and 'enum ieee80211_band'
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 15 Sep 2010 19:26:13 +0000 (15:26 -0400)]
ath9k: make ath_ant_div_conf_fast_divbias static
CHECK drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/ath/ath9k/recv.c:1341:6: warning: symbol 'ath_ant_div_conf_fast_divbias' was not declared. Should it be static?
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 15 Sep 2010 19:16:22 +0000 (15:16 -0400)]
iwlwifi: fix sparse warning about wrong enum for band parameter
drivers/net/wireless/iwlwifi/iwl-scan.c:386:27: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:386:27: int enum nl80211_band versus
drivers/net/wireless/iwlwifi/iwl-scan.c:386:27: int enum ieee80211_band
drivers/net/wireless/iwlwifi/iwl-scan.c:435:57: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:435:57: int enum ieee80211_band versus
drivers/net/wireless/iwlwifi/iwl-scan.c:435:57: int enum nl80211_band
drivers/net/wireless/iwlwifi/iwl-scan.c:474:53: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:474:53: int enum ieee80211_band versus
drivers/net/wireless/iwlwifi/iwl-scan.c:474:53: int enum nl80211_band
drivers/net/wireless/iwlwifi/iwl-scan.c:588:72: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:588:72: int enum ieee80211_band versus
drivers/net/wireless/iwlwifi/iwl-scan.c:588:72: int enum nl80211_band
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 15 Sep 2010 13:13:13 +0000 (15:13 +0200)]
mac80211: set running state earlier
When an interface is brought up, the recent changes
to allow changing type-while-up only set the running
bit after everything was done. This broke a number
of things, including idle calculation for monitor
interfaces, and it also broke WDS station insertion
(although nobody noticed yet).
Thus, change the code to set the running bit earlier,
but keep it after the driver's add_interface was
called because otherwise drivers may iterate over
interfaces they haven't fully set up yet.
Reported-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 15 Sep 2010 11:28:15 +0000 (13:28 +0200)]
cfg80211/mac80211: use lockdep_assert_held
Instead of using a WARN_ON(!mutex_is_locked())
use lockdep_assert_held() which compiles away
completely when lockdep isn't enabled, and
also is a more accurate assertion since it
checks that the current thread is holding the
mutex.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 14 Sep 2010 20:06:53 +0000 (22:06 +0200)]
mac80211: use correct station flags lock
This code is modifying the station flags, and
as such should hold the flags lock so it can
do so atomically vs. other flags modifications
and readers. This issue was introduced when
this code was added in eccb8e8f, as it used
the wrong lock (thus not fixing the race that
was previously documented in a comment.)
Cc: stable@kernel.org [2.6.31+] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Wed, 8 Sep 2010 07:04:43 +0000 (16:04 +0900)]
ath5k: Use common ath key management functions
Use common ath key management functions in ath5k. This fixes problems with HW
encryption in AP mode, which was broken in the ath5k implementation.
Before (with the ath5k implementation) only one client could connect to the AP
using HW encryption and WPA. When a second client connected, the first client
was not able to send/receive any more packets. Because of the problems with HW
encryption, software encryption was always used in AP mode, which resulted in a
high CPU load (and/or low thruput) on embedded devices. Instead of trying to
fix the implementation in ath5k it makes more sense to share the code with
ath9k.
This also enables HW encryption for AP mode again.
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Wed, 8 Sep 2010 07:04:38 +0000 (16:04 +0900)]
ath: Copy key cache management functions from ath9k to ath
Copied the key cache management functions from ath9k (common.c and hw.c) to
ath/key.c so we can use them from ath5k, later.
Minor changes have been made:
- renamed ath9k_* to ath_*
- replaced ah->caps.keycache_size with common->keymax
- removed ATH9K_IS_MIC_ENABLED since it is always true.
- the AR_PCU_MIC_NEW_LOC_ENA flag is replaced with (splitmic == 0).
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 14 Sep 2010 20:26:44 +0000 (16:26 -0400)]
wl1271: remove warnings in wl1271_sdio_set_power
These were introduced in "wl1271: sdio: claim host only when doing IO"
drivers/net/wireless/wl12xx/wl1271_sdio.c: In function ‘wl1271_sdio_set_power’:
drivers/net/wireless/wl12xx/wl1271_sdio.c:193: warning: ‘return’ with a value, in function returning void
drivers/net/wireless/wl12xx/wl1271_sdio.c:195: warning: ‘return’ with a value, in function returning void
drivers/net/wireless/wl12xx/wl1271_sdio.c:186: warning: unused variable ‘func’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 14 Sep 2010 19:34:14 +0000 (21:34 +0200)]
mac80211: match only assigned bss in sta_info_get_bss
sta_info_get_bss() is used to match STA pointers
for VLAN/AP interfaces, but if the same station
is also added to multiple other interfaces it
will erroneously match because both pointers are
NULL, fix this by ignoring NULL pointers here.
Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 14 Sep 2010 16:37:19 +0000 (18:37 +0200)]
ath9k: fix BSSID mask calculation
At the time the .add_interface driver op is called, the interface has not
been marked as running yet, so ieee80211_iterate_active_interfaces will
not pass it to the iterator function.
Because of this, the calculated BSSID mask is wrong, which breaks multi-BSS
operation.
Additionally, the current way of comparing all addresses against each other
is pointless, as the hardware only uses the hardware MAC address and the BSSID
mask for matching the destination address, so all the address array
reallocation is completely unnecessary.
This patch simplifies the logic by setting the initial mask bytes to 0xff
and removing all bits in the iterator call that don't match the hardware MAC
address. It also calls the iterator for the vif that was passed to
add_interface()
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Tested-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The CPU consumption during the scan period is high, since
the register write go over Interrupt endpoint. On downloading
the firmware to the target, the USB descriptors are
'patched' to change the type of the endpoints from Interrupt
to Bulk.
With this fix, the CPU usage during a scan run comes down to
acceptable levels.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even is someone else complete scanning in mac80211, apply rxon and
tx power settings if gets scan complete notification from hardware.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace IWL_DEBUG_{INFO,HC,RC} to IWL_DEBUG_SCAN in iwl-scan.c file. Add
some more IWL_DEBUG_SCAN messages. This will allow to fully debug
scanning using only IWL_DL_SCAN flag.
Also start one message sentence with capital letter, since that
convention in iwl-scan.c file.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove redundant checks and use iwl_is_ready_rf().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: wait for scan work complete before restarting hw
This is needed to avoid warning in ieee80211_restart_hw about hardware
scan in progress.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we force scan complete at the end of iwl_scan_cancel_timeout
function. This cause race condition when we can get a new scan request
from mac80211 and complete it by iwl_bg_complete from older scan. Change
code to force scan complete only when really needed: device goes down,
interface is removed or scan timeout occurs.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: assure we complete scan in scan_abort and scan_check works
Assure we complete scan in mac80211 when we abort scanning (scan_abort
work) or scan timeout occurs (scan_check work). Currently
iwl_scan_cancel_timeout() procedure force scan finish in mac80211
at the end of timeout loop, so we can use it in proper work functions.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we do not get notification from hardware about scan complete, after
timeout do mac80211 scan completion anyway. This assure we end scan
in case of firmware hung.
Patch fix one of the causes of wdev_cleanup_work warning reported at
https://bugzilla.redhat.com/show_bug.cgi?id=593566
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assure (partially) we call ieee80211_scan_completed() only once when
scan was requested from mac80211.
Code path that first clear STATUS_SCANNING bit is responsible to call
ieee80211_scan_completed(). Before the call, we check if mac80211
really request the scan.
Still persist some cases when we behave wrong, that will be addressed
in the next patches.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since on timeout version of iwl_scan_cancel procedure we can sleep,
do not have to schedule abort_scan work to begin and perform scanning,
can do this directly. Also now, as we do not queue abort_scan from
restart work anymore, we can queue abort_scan to priv->workqueue.
Don't drop mutex when waiting for scan complete. Use STATUS_HW_SCAN bit
to check if scanning is currently pending, because STATUS_SCANNING will
be cleared only with priv->mutex taken.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we are not able to send abort command to firmware, notify mac80211
that we complete scan, as we will newer do it lately. Check for all
possible errors that low level sending command procedure does not check,
to assure we catch all failures cases.
Patch fix one of the causes of wdev_cleanup_work warning reported at
https://bugzilla.redhat.com/show_bug.cgi?id=593566
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Always cancel scan when stooping device and scan is currently pending,
we should newer have scan running after down device.
To assure we start scan cancel from restart work we have to schedule
abort_scan to different workqueue than priv->workqueue.
Patch fix not cancel scanning when restarting firmware, what is
one of the causes of wdev_cleanup_work warning (together with permanent
network connection lost) reported at
https://bugzilla.redhat.com/show_bug.cgi?id=593566
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 13 Sep 2010 12:46:34 +0000 (14:46 +0200)]
iwlwifi: move scan completed flags handling
Move the scan completed flags handling so that we
can notify mac80211 about aborted scans with the
correct status. Also queue the scan_completed work
before the BT status update so that it won't see
the bits still set (unless a new scan was started
in which case that's fine.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 13 Sep 2010 12:46:33 +0000 (14:46 +0200)]
iwlwifi: unify scan start checks
Rather than duplicating all the checks and even
in case of errors accepting the scan request
from mac80211, we can push the checks to the
caller and in all error cases reject the scan
request right away (rather than accepting and
then saying it was aborted).
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 13 Sep 2010 12:46:32 +0000 (14:46 +0200)]
iwlwifi: remove unused conf variables
There are a number of conf variables that are
unused, remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k: use ARRAY_SIZE macro in ani.c
Replace (sizeof(ofdm_level_table)/sizeof(ofdm_level_table[0]) with
ARRAY_SIZE(ofdm_level_table), and (sizeof(cck_level_table)/
sizeof(cck_level_table[0]) with ARRAY_SIZE(cck_level_table) in
drivers/net/wireless/ath/ath9k/ani.c
Signed-off-by: Nikitas Angelinas <nikitasangelinas@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Wed, 8 Sep 2010 18:57:40 +0000 (20:57 +0200)]
rt2x00: fix oops in rt2x00lib_txdone with rt61pci
Fix a typo introduced in "rt2x00: Add helper function for reporting tx
status" that results in an oops in rt2x00lib_txdone.
Reported-by: Pavel Roskin <proski@gnu.org> Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Wed, 8 Sep 2010 18:57:10 +0000 (20:57 +0200)]
rt2x00: Enable missing interrupts in rt61pci
We're handling both, the CSR_BEACON_DONE and the CSR_TWAKEUP interrupts
in rt61pci. However, these interrupts are masked out by default. Fix
this.
Found via pure code inspection.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Wed, 8 Sep 2010 18:56:52 +0000 (20:56 +0200)]
rt2x00: Mask out unused interrupts in rt2800pci
We don't use all available interrupts in rt2800pci. Mask out all unused
interrupts to avoid waking up without having anything to do.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Wed, 8 Sep 2010 18:56:32 +0000 (20:56 +0200)]
rt2x00: Check for specific changed flags when updating the erp config
Previously rt2x00 was always updating all erp related config variables
even though mac80211 might only have changed one. Hence, pass the
changed flags to the config_erp driver callback so that the driver
can limit the changes to the correct values.
This fixes an issue in AP mode where the beacon interval is not
initialized (and thus zero) but still sent to the hardware causing an
interrupt storm on rt2800pci hanging the system.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Wed, 8 Sep 2010 18:56:04 +0000 (20:56 +0200)]
rt2x00: Initialize AMPDU_BA_WINSIZE register
Since we're not using the AMPDU_BA_WINSIZE register to force the BlockAck
window size (we specify it in every TXWI) we should initialize it to 0.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lars Ericsson [Wed, 8 Sep 2010 18:55:36 +0000 (20:55 +0200)]
rt2x00: Antenna diversity does not work in 2.6.35
The test if antenna diversity is at all enabled uses a local variable
'flags' to prepare the test condition, but uses 'ant->flags' when the test
is evaluated. The effect is that the diversity evaluation will never start.
I can see two solutions, use the 'flag' in the test condition or revert the
local flag change. My attached patch took alternative two.
Then the evaluation start but it will still not switch antenna. The problem
is a code section in rt2x00lib_config_antenna (). The effect of that code
section is that any change the diversity function perform will be
effectively shorten and no antenna selection command issued. The attached
patch will filter out any ANTENNA_SW_DIVERSITY setting but forward all
other
Signed-off-by: Lars Ericsson <lars_ericsson@telia.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 3 Sep 2010 18:42:04 +0000 (11:42 -0700)]
iwlwifi: make sure runtime calibration is enabled after association
Clear the "start calib" flag only for new association,
The flag will be set in post_associate function to trigger
the runtime calibration. Set this flag to "0" will stop the
runtime sensitivity calibration
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 3 Sep 2010 13:30:55 +0000 (06:30 -0700)]
iwlwifi: fix and describe iwl_adjust_beacon_interval
The iwl_adjust_beacon_interval function is a bit
of black magic, so add comments to it describing
what it does. Also, in the case when there's no
beacon interval set, program the default into
the device (instead of adjusting, which results
in the max) since using the max in that case
interacts badly with dual-mode/PAN parameters.
Also update the PAN parameters accordingly and
use the same constant as here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 3 Sep 2010 13:31:26 +0000 (06:31 -0700)]
iwlwifi: improve timing handling with dual-mode
In dual-mode, a number of scenarios need to be
considered, and the firmware can be very picky
about them. Adjust the timing (most importantly
the beacon interval) according to the different
modes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 3 Sep 2010 13:32:21 +0000 (06:32 -0700)]
iwlwifi: avoid sending too many commands
When the PAN context is unused, there's no
need to continually update it in the device.
So track which contexts are active (with the
special case that the WLAN context is always
active ...) and only send their commands to
the device when needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Mon, 30 Aug 2010 13:12:00 +0000 (06:12 -0700)]
iwlwifi: fix PAN parameters while scanning
When only the PAN side was active, we gave no
time to the WLAN context, which is OK unless
we are scanning, which always happens on the
WLAN context. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Fri, 27 Aug 2010 17:41:37 +0000 (10:41 -0700)]
iwlwifi: remember the last uCode sysassert error code
When sysassert happen, uCode will report the error code,
driver dump the information to dmesg. Here also remember
the last error code for future reference.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tomas Winkler [Mon, 23 Aug 2010 21:00:54 +0000 (14:00 -0700)]
iwlwifi: fix default LQ table in 5.2 band
The default LQ is filled decreasingly using
iwl_get_prev_ieee_rate from a starting rate.
Since the starting rate is already the lowest one for
a specific band it should be actually filled evenly with
the starting rate: 1M and 6M for 5.2GHZ and 2.4GH respectively.
The bug is that for for A or G-only it decreases to
CCK rates which are not supported.
iwl_get_prev_ieee_rate function is just not band aware.
This affects broadcast station which lq table
is not updated by rs algorithm
G-only scenario is not treated by this patch
iwl_get_prev_ieee_rate is removed completely as it
is not used in other contexts
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Julia Lawall [Sun, 5 Sep 2010 19:00:26 +0000 (21:00 +0200)]
drivers/net/wireless/iwlwifi/iwl-agn.c: Fix return value from an unsigned function
The function has an unsigned return type, but returns a negative constant
to indicate an error condition. Another error condition in the same
function is indicated by returning 0, and indeed the only call to the
function checks for 0 to detect errors, so the return of a negative value
it converted to a return of 0.
A sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
Michael Büsch [Sat, 4 Sep 2010 22:55:38 +0000 (00:55 +0200)]
p54spi: Add error message for eeprom failure
This adds an error message for the eeprom request failure
case. This way it's easier for the user to figure out
what went wrong.
Signed-off-by: Michael Büsch <mb@bu3sch.de> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw: Restore ANI registers to default during partial reset for AR9271
For AR9271 chips, if partial reset is done while scanning, the cycpwrThr1
will be set to maximum. This causes the degrade in DL throughput.
So restore the ANI registers to default during the partial reset.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: Implement an algorithm for Antenna diversity and combining
This algorithm chooses the best main and alt lna out of
LNA1, LNA2, LNA1+LNA2 and LNA1-LNA2 to improve rx for single
chain chips(AR9285). This would greatly improve rx when there
is only one antenna is connected with AR9285.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Mon, 23 Aug 2010 22:24:49 +0000 (15:24 -0700)]
iwlagn: open/close envlope to force move BT state machine
In uCode, BT state machine need to receive open envlope
command before perform calibration; followed by close envlope
command to move to next stage.
Since Linux has two separated uCode, one for init and the second
one for runtime; we use open envlope commands for init uCode to
indicate we are ready to perform calibration operation.
But for runtime uCode, we are not doing any init calibration,
so we issue open/close envlope commands to force uCode move to
"BT COEX ON" state.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
mac80211: only cancel software-based scans on suspend
Otherwise the hardware scan handler could access an invalid scan request
structure. The driver should cancel any pending hardware scans during
the suspend process anyway, so also add a warning if the hardware scan
is still pending when the device resumes.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 30 Aug 2010 19:12:02 +0000 (15:12 -0400)]
mac80211: cancel scan in ieee80211_restart_hw if software scan pending
This function exists to clean-up after a hardware error or something
similar. The restart is accomplished using the same infrastructure used
to resume after a suspend. The suspend path cancels running scans, so
it seems appropriate to do that here as well for software-based scans.
If a hardware-based scan is pending, issue a warning message since this
indicates that the drivers has failed to clean-up after itself.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 30 Aug 2010 19:15:51 +0000 (21:15 +0200)]
rt2x00: Cleanup rt2x00usb_watchdog_reset_tx
rt2x00usb_watchdog_reset_tx performs the same task
as rt2x00usb_kill_tx_queue, with the only difference
is that it waits for all entries to be returned to
the driver and for all frames the status has been
reported to mac80211.
We can easily split this task by calling rt2x00usb_kill_tx_queue,
sleep for a short period and invoke the TX status reporting
function. By adding the sleep() to the kill_entry we make sure
that even during shutdown we guarentee the entry has been killed when
the function returns. To make this work correctly the interrupt
handlers have to be updated to prevent checking for the RADIO_ENABLED
flag too early which prevents the ownership of the entry to be reset.
Additionally a check for the DEVICE_PRESENT flag is not required but
is nice to prevent race conditions when the device was unplugged.
Additionally rather then calling rt2x00usb_work_txdone() for
status reporting we let the driver perform the TX status reporting
first. If this is not sufficient then rt2x00usb_work_txdone() will
still be used to cleanup the mess.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 30 Aug 2010 19:15:19 +0000 (21:15 +0200)]
rt2x00: Split watchdog check into a DMA and STATUS timeout
The watchdog for rt2800usb triggers frequently causing all URB's
to be canceled often enough to interrupt the normal TX flow.
More research indicated that not the URB upload to the USB host
were hanging, but instead the TX status reports.
To correctly detect what is going on, we introduce Q_INDEX_DMA_DONE
which is an index counter between Q_INDEX_DONE and Q_INDEX and indicates
if the frame has been transfered to the device.
This also requires the rt2x00queue timeout functions to be updated
to differentiate between a DMA timeout (time between Q_INDEX and
Q_INDEX_DMA_DONE timeout) and a STATUS timeout (time between
Q_INDEX_DMA_DONE and Q_INDEX_DONE timeout)
All Q_INDEX_DMA_DONE code was taken from the RFC from
Helmut Schaa <helmut.schaa@googlemail.com> for the implementation
for watchdog for rt2800pci.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 30 Aug 2010 19:14:56 +0000 (21:14 +0200)]
rt2x00: Correctly kill beacon queue
USB devices upload their beacon and then automatically send
it out every beacon interval. However when killing a TX queue
we only kill the URB and not the actual transmission of the beacon.
This will reset the Beacon register to prevent any beacons from
being transmitted.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 30 Aug 2010 19:14:38 +0000 (21:14 +0200)]
rt2x00: Set PWR_PIN_CFG during initialization
Add PWR_PIN_CFG initialization for rt2800usb at the same point
as rt2800pci.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 30 Aug 2010 19:14:15 +0000 (21:14 +0200)]
rt2x00: Don't set unicast/BSSID masks when clearning MAC or BSSID
When configuring the MAC_ADDR or MAC_BSSID with an empty address,
the UNICAST_TO_ME_MASK and BSS_ID_MASK must also be reset to prevent
invalid interpretation of the addresses.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 30 Aug 2010 19:13:54 +0000 (21:13 +0200)]
rt2x00: Wakeup hardware before loading firmware
According to the legacy drivers the AUTOWAKEUP_CFG
register must be reset to 0 before loading the firmware.
Instead of during rt2800{pci,usb}_write_firmware it
must actually be done in rt2800_load_firmware() before
resetting the WPDMA_GLO_CFG and PWR_PIN_CFG registers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 30 Aug 2010 19:13:30 +0000 (21:13 +0200)]
rt2x00: Validate TX status results with current data entry
Instead of printing a warning when the PID, ACK, or WCID of
an entry don't match the TX status report, we should skip the
entry to search for the entry which actually does match
the TX status data.
This reduces the number of watchdog errors on the TX queues
for rt2800usb, and seems to improve the reliability of the
TX flow a bit.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 30 Aug 2010 19:13:08 +0000 (21:13 +0200)]
rt2x00: Add rt2800_wait_csr_ready
Similar to rt2800_wait_wpdma_ready() we can add a
function to waiting until the CSR is ready. This
centralizes some additional code into rt2800lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Mon, 30 Aug 2010 19:12:47 +0000 (21:12 +0200)]
rt2x00: Update rt2800 comments regarding AMPDU and PACKET_ID in TXWI
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Variables containing queue ids are called qid everywhere else, hence
rename the queue field in txentry_desc to qid as well.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 28 Aug 2010 16:21:21 +0000 (18:21 +0200)]
ath9k: fix spurious MIC failure reports
According to the hardware documentation, the MIC failure bit is only
valid if the frame was decrypted using a valid TKIP key and is not a
fragment.
In some setups I've seen hardware-reported MIC failures on an AP that
was configured for CCMP only, so it's clear that additional checks are
necessary.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
here's the original message:
The queue stopping/waking functionality was broken in a way that could
cause huge latencies in TX transfers and even cause the TX to stall in the
right circumstances. Correct these problems.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> Acked-by: Kalle Valo <kvalo@adurom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Fri, 27 Aug 2010 19:22:00 +0000 (22:22 +0300)]
mac80211: Do not generate CQM events based on first Beacon frames
The signal strength value in a single RX frame is not that reliable,
so it is better to delay start of CQM events until there is a real
average signal strength from more than a single Beacon frame
available.
Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Fri, 27 Aug 2010 19:21:13 +0000 (22:21 +0300)]
mac80211: Fix signal strength average initialization for CQM events
The ave_beacon_signal value uses 1/16 dB unit and as such, must be
initialized with the signal level of the first Beacon frame multiplied
by 16. This fixes an issue where the initial CQM events are reported
incorrectly with a burst of events while the running average
approaches the correct value after the incorrect initialization. This
could cause user space -based roaming decision process to get quite
confused at the moment when we would like to go through authentication
and DHCP.
Cc: stable@kernel.org Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
git://bbs.cooldavid.org / net-next-2.6.git / log