vhost: avoid pr_err on condition guest can trigger
Guest can trigger packet truncation by posting
a very short buffer and disabling buffer merging.
Convert pr_err to pr_debug to avoid log from filling
up when this happens.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Ben Greear [Thu, 15 Jul 2010 13:22:33 +0000 (13:22 +0000)]
ipmr: Don't leak memory if fib lookup fails.
This was detected using two mcast router tables. The
pimreg for the second interface did not have a specific
mrule, so packets received by it were handled by the
default table, which had nothing configured.
This caused the ipmr_fib_lookup to fail, causing
the memory leak.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Deucher [Thu, 15 Jul 2010 14:51:10 +0000 (10:51 -0400)]
drm/radeon/kms: fix gtt MC base alignment on rs4xx/rs690/rs740 asics
The asics in question have the following requirements with regard to
their gart setups:
1. The GART aperture size has to be in the form of 2^X bytes, where X is from 25 to 31
2. The GART aperture MC base has to be aligned to a boundary equal to the size of the
aperture.
3. The GART page table has to be aligned to the boundary equal to the size of the table.
4. The GART page table size is: table_entry_size * (aperture_size / page_size)
5. The GART page table has to be allocated in non-paged, non-cached, contiguous system
memory.
This patch takes care 2. The rest should already be handled properly.
This fixes a regression noticed by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com> Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jan Kara [Wed, 14 Jul 2010 05:56:33 +0000 (07:56 +0200)]
jbd2/ocfs2: Fix block checksumming when a buffer is used in several transactions
OCFS2 uses t_commit trigger to compute and store checksum of the just
committed blocks. When a buffer has b_frozen_data, checksum is computed
for it instead of b_data but this can result in an old checksum being
written to the filesystem in the following scenario:
1) transaction1 is opened
2) handle1 is opened
3) journal_access(handle1, bh)
- This sets jh->b_transaction to transaction1
4) modify(bh)
5) journal_dirty(handle1, bh)
6) handle1 is closed
7) start committing transaction1, opening transaction2
8) handle2 is opened
9) journal_access(handle2, bh)
- This copies off b_frozen_data to make it safe for transaction1 to commit.
jh->b_next_transaction is set to transaction2.
10) jbd2_journal_write_metadata() checksums b_frozen_data
11) the journal correctly writes b_frozen_data to the disk journal
12) handle2 is closed
- There was no dirty call for the bh on handle2, so it is never queued for
any more journal operation
13) Checkpointing finally happens, and it just spools the bh via normal buffer
writeback. This will write b_data, which was never triggered on and thus
contains a wrong (old) checksum.
This patch fixes the problem by calling the trigger at the moment data is
frozen for journal commit - i.e., either when b_frozen_data is created by
do_get_write_access or just before we write a buffer to the log if
b_frozen_data does not exist. We also rename the trigger to t_frozen as
that better describes when it is called.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Mark Fasheh <mfasheh@suse.com> Signed-off-by: Joel Becker <joel.becker@oracle.com>
Wengang Wang [Wed, 14 Jul 2010 14:38:21 +0000 (22:38 +0800)]
ocfs2/dlm: Remove BUG_ON from migration in the rare case of a down node
For migration, we are waiting for DLM_LOCK_RES_MIGRATING flag to be set
before sending DLM_MIG_LOCKRES_MSG message to the target. We are using
dlm_migration_can_proceed() for that purpose. However, if the node is
down, dlm_migration_can_proceed() will also return "go ahead". In this
rare case, the DLM_LOCK_RES_MIGRATING flag might not be set yet. Remove
the BUG_ON() that trips over this condition.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com> Signed-off-by: Joel Becker <joel.becker@oracle.com>
Thomas Gleixner [Wed, 14 Jul 2010 19:36:27 +0000 (21:36 +0200)]
x86: Force HPET readback_cmp for all ATI chipsets
commit 30a564be (x86, hpet: Restrict read back to affected ATI
chipset) restricted the workaround for the HPET bug to SMX00
chipsets. This was reasonable as those were the only ones against
which we ever got a bug report.
Stephan Wolf reported now that this patch breaks his IXP400 based
machine. Though it's confirmed to work on other IXP400 based systems.
To error out on the safe side, we force the HPET readback workaround
for all ATI SMbus class chipsets.
Reported-by: Stephan Wolf <stephan@letzte-bankreihe.de>
LKML-Reference: <alpine.LFD.2.00.1007142134140.3321@localhost.localdomain> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Stephan Wolf <stephan@letzte-bankreihe.de> Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Bob Peterson [Wed, 14 Jul 2010 22:12:26 +0000 (18:12 -0400)]
GFS2: rename causes kernel Oops
This patch fixes a kernel Oops in the GFS2 rename code.
The problem was in the way the gfs2 directory code was trying
to re-use sentinel directory entries.
In the failing case, gfs2's rename function was renaming a
file to another name that had the same non-trivial length.
The file being renamed happened to be the first directory
entry on the leaf block.
First, the rename code (gfs2_rename in ops_inode.c) found the
original directory entry and decided it could do its job by
simply replacing the directory entry with another. Therefore
it determined correctly that no block allocations were needed.
Next, the rename code deleted the old directory entry prior to
replacing it with the new name. Therefore, the soon-to-be
replaced directory entry was temporarily made into a directory
entry "sentinel" or a place holder at the start of a leaf block.
Lastly, it went to re-add the replacement directory entry in
that leaf block. However, when gfs2_dirent_find_space was
looking for space in the leaf block, it used the wrong value
for the sentinel. That threw off its calculations so later
it decides it can't really re-use the sentinel and therefore
must allocate a new leaf block. But because it previously decided
to re-use the directory entry, it didn't waste the time to
grab a new block allocation for the inode. Therefore, the
inode's i_alloc pointer was still NULL and it crashes trying to
reference it.
In the case of sentinel directory entries, the entire dirent is
reused, not just the "free space" portion of it, and therefore
the function gfs2_dirent_find_space should use the value 0
rather than GFS2_DIRENT_SIZE(0) for the actual dirent size.
Fixing this calculation enables the reproducer programs to work
properly.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Abhijith Das [Sun, 4 Jul 2010 05:33:24 +0000 (01:33 -0400)]
GFS2: BUG in gfs2_adjust_quota
HighMem pages on i686 do not get mapped to the buffer_heads and this was
causing a NULL pointer dereference when we were trying to memset page buffers
to zero.
We now use zero_user() that kmaps the page and directly manipulates page data.
This patch also fixes a boundary condition that was incorrect.
Signed-off-by: Abhi Das <adas@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Bob Peterson [Thu, 17 Jun 2010 20:45:37 +0000 (16:45 -0400)]
GFS2: Fix kernel NULL pointer dereference by dlm_astd
This patch fixes a problem in an error path when looking
up dinodes. There are two sister-functions, gfs2_inode_lookup
and gfs2_process_unlinked_inode. Both functions acquire and
hold the i_iopen glock for the dinode being looked up. The last
thing they try to do is hold the i_gl glock for the dinode.
If that glock fails for some reason, the error path was
incorrectly calling gfs2_glock_put for the i_iopen glock twice.
This resulted in the glock being prematurely freed. The
"minimum hold time" usually kept the glock in memory, but the
lock interface to dlm (aka lock_dlm) freed its memory for the
glock. In some circumstances, it would cause dlm's dlm_astd daemon
to try to call the bast function for the freed lock_dlm memory,
which resulted in a NULL pointer dereference.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Bob Peterson [Wed, 23 Jun 2010 15:44:47 +0000 (11:44 -0400)]
GFS2: recovery stuck on transaction lock
This patch fixes bugzilla bug #590878: GFS2: recovery stuck on
transaction lock. We set the frozen flag on the glock when we receive
a completion that cannot be delivered due to blocked locks. At that
point we check to see whether the first waiting holder has the noexp
flag set. If the noexp lock is queued later, then we need to unfreeze
the glock at that point in time, namely, in the glock work function.
This patch was originally written by Steve Whitehouse, but since
he's on holiday, I'm submitting it. It's been well tested with a
complex recovery test called revolver.
Signed-off-by: Steve Whitehouse <swhiteho@redhat.com> Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Bob Peterson [Thu, 24 Jun 2010 23:15:09 +0000 (19:15 -0400)]
GFS2: O_TRUNC not working on stuffed files across cluster
This patch replaces a statement that got dropped out by accident.
Without the patch, truncates on stuffed (very small) files cause
those files to have an unpredictable size.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Tom Herbert [Thu, 15 Jul 2010 03:50:29 +0000 (20:50 -0700)]
net: fix problem in reading sock TX queue
Fix problem in reading the tx_queue recorded in a socket. In
dev_pick_tx, the TX queue is read by doing a check with
sk_tx_queue_recorded on the socket, followed by a sk_tx_queue_get.
The problem is that there is not mutual exclusion across these
calls in the socket so it it is possible that the queue in the
sock can be invalidated after sk_tx_queue_recorded is called so
that sk_tx_queue get returns -1, which sets 65535 in queue_index
and thus dev_pick_tx returns 65536 which is a bogus queue and
can cause crash in dev_queue_xmit.
We fix this by only calling sk_tx_queue_get which does the proper
checks. The interface is that sk_tx_queue_get returns the TX queue
if the sock argument is non-NULL and TX queue is recorded, else it
returns -1. sk_tx_queue_recorded is no longer used so it can be
completely removed.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring DMVPN (GRE + openNHRP) and a GRE remote
address is configured a kernel Oops is observed. The
obserseved Oops is caused by a NULL header_ops pointer
(neigh->dev->header_ops) in neigh_update_hhs() when
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/fsl-booke: Fix address issue when using relocatable kernels
powerpc/cpm1: Mark micropatch code/data static and __init
powerpc/cpm1: Fix build with various CONFIG_*_UCODE_PATCH combinations
powerpc/cpm: Reintroduce global spi_pram struct (fixes build issue)
Nicolas Pitre [Wed, 14 Jul 2010 04:21:22 +0000 (05:21 +0100)]
ARM: 6226/1: fix kprobe bug in ldr instruction emulation
From: Bin Yang <bin.yang@marvell.com>
Cc: stable@kernel.org Signed-off-by: Bin Yang <bin.yang@marvell.com> Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Timo Teräs [Mon, 12 Jul 2010 21:29:42 +0000 (21:29 +0000)]
xfrm: do not assume that template resolving always returns xfrms
xfrm_resolve_and_create_bundle() assumed that, if policies indicated
presence of xfrms, bundle template resolution would always return
some xfrms. This is not true for 'use' level policies which can
result in no xfrm's being applied if there is no suitable xfrm states.
This fixes a crash by this incorrect assumption.
Reported-by: George Spelvin <linux@horizon.com> Bisected-by: George Spelvin <linux@horizon.com> Tested-by: George Spelvin <linux@horizon.com> Signed-off-by: Timo Teräs <timo.teras@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Axel Lin [Wed, 14 Jul 2010 11:06:07 +0000 (19:06 +0800)]
ASoC:: remove a redundant snd_soc_unregister_codec call in wm8988_register
snd_soc_unregister_codec is called twice if snd_soc_register_dai fail.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Wed, 14 Jul 2010 10:57:31 +0000 (18:57 +0800)]
ASoC: wm8727: add a missing return in wm8727_platform_probe
otherwise the error path will always be executed.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
John W. Linville [Tue, 13 Jul 2010 18:06:32 +0000 (14:06 -0400)]
hostap_pci: set dev->base_addr during probe
"hostap: Protect against initialization interrupt" (which reinstated
"wireless: hostap, fix oops due to early probing interrupt")
reintroduced Bug 16111. This is because hostap_pci wasn't setting
dev->base_addr, which is now checked in prism2_interrupt. As a result,
initialization was failing for PCI-based hostap devices. This corrects
that oversight.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit 83ba9ea8a04b72dfee2515428c15e7414ba4fc61 ommitted the return
line for the old synaptics model accidentally. This resulted in a wrong
check, namely, the dimensions are checked for the old devices that don't
support the query properly.
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
input: i8042 - add runtime check in x86's i8042_platform_init
Revert "Input: fixup X86_MRST selects"
Revert "Input: do not force selecting i8042 on Moorestown"
x86, mrst: Add i8042_detect API for Moorestwon platform
x86: Add i8042 pre-detection hook to x86_platform_ops
x86, platform: Export x86_platform to modules
Acked-by: Nicolas Pitre <nico@fluxnic.net> Acked-by: Russell King <linux@arm.linux.org.uk> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'v4l_for_2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB: uvc: Fix multiple symbols definitions with UVC gadget and host drivers
V4L/DVB: v4l: mem2mem_testdev: fix g_fmt NULL pointer dereference
V4L/DVB: uvcvideo: Power line frequency control doesn't support GET_MIN/MAX/RES
V4L/DVB: ivtv: Add delay to ensure the decoder always restarts with a blank screen
V4L/DVB: Documentation: Add the Philips FQ1236 MK5 to video4linux/CARDLIST.tuner
V4L/DVB: tveeprom: Add an entry for tuner code 168: a TCL M30WTP-4N-E tuner
V4L/DVB: tuner: Add a definition for the Philips FQ1236 MK5 NTSC tuner
V4L/DVB: OMAP_VOUT: fix: Module params were not working through bootargs
V4L/DVB: OMAP_VOUT: fix: Replaced dma-sg with dma-contig
V4L/DVB: OMAP_VOUT:Build FIX: Rebased against latest DSS2 changes
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Send Report ID when numbered reports are sent over the control endpoint.
HID: Enable HID_QUIRK_MULTI_INPUT for Retro Adaptor
HID: add support for CH Eclipse yoke
HID: eliminate a double lock in debug code
HID: ntrig: add support for new firwmare versions
HID: check for HID_QUIRK_IGNORE during probing
HID: roccat: fix modules interdependencies
Dan Carpenter [Sat, 10 Jul 2010 14:33:36 +0000 (16:33 +0200)]
ocfs2: tighten up strlen() checking
This function is only called from one place and it's like this:
dlm_register_domain(conn->cc_name, dlm_key, &fs_version);
The "conn->cc_name" is 64 characters long. If strlen(conn->cc_name)
were equal to O2NM_MAX_NAME_LEN (64) that would be a bug because
strlen() doesn't count the NULL character.
In fact, if you look how O2NM_MAX_NAME_LEN is used, it mostly describes
64 character buffers. The only exception is nd_name from struct
o2nm_node.
Anyway I looked into it and in this case the domain string comes from
osb->uuid_str in ocfs2_setup_osb_uuid(). That's 32 characters and NULL
which easily fits into O2NM_MAX_NAME_LEN. This patch doesn't change how
the code works, but I think it makes the code a little cleaner.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Joel Becker <joel.becker@oracle.com>
Tao Ma [Fri, 9 Jul 2010 06:53:12 +0000 (14:53 +0800)]
ocfs2: Make xattr reflink work with new local alloc reservation.
The new reservation code in local alloc has add the limitation
that the caller should handle the case that the local alloc
doesn't give use enough contiguous clusters. It make the old
xattr reflink code broken.
So this patch udpate the xattr reflink code so that it can
handle the case that local alloc give us one cluster at a time.
Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Joel Becker <joel.becker@oracle.com>
Tao Ma [Fri, 9 Jul 2010 06:53:11 +0000 (14:53 +0800)]
ocfs2: make xattr extension work with new local alloc reservation.
The old ocfs2_xattr_extent_allocation is too optimistic about
the clusters we can get. So actually if the file system is
too fragmented, ocfs2_add_clusters_in_btree will return us
with EGAIN and we need to allocate clusters once again.
So this patch change it to a while loop so that we can allocate
clusters until we reach clusters_to_add.
Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Joel Becker <joel.becker@oracle.com> Cc: stable@kernel.org
Tao Ma [Thu, 8 Jul 2010 03:11:11 +0000 (11:11 +0800)]
ocfs2: Remove the redundant cpu_to_le64.
In ocfs2_block_group_alloc, we set c_blkno by bg->bg_blkno.
But actually bg->bg_blkno is already changed to little endian
in ocfs2_block_group_fill. So remove the extra cpu_to_le64.
Reported-by: Marcos Matsunaga <Marcos.Matsunaga@oracle.com> Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Joel Becker <joel.becker@oracle.com>
Joel Becker [Sat, 3 Jul 2010 00:20:27 +0000 (17:20 -0700)]
ocfs2: No need to zero pages past i_size.
When ocfs2 fills a hole, it does so by allocating clusters. When a
cluster is larger than the write, ocfs2 must zero the portions of the
cluster outside of the write. If the clustersize is smaller than a
pagecache page, this is handled by the normal pagecache mechanisms, but
when the clustersize is larger than a page, ocfs2's write code will zero
the pages adjacent to the write. This makes sure the entire cluster is
zeroed correctly.
Currently ocfs2 behaves exactly the same when writing past i_size.
However, this means ocfs2 is writing zeroed pages for portions of a new
cluster that are beyond i_size. The page writeback code isn't expecting
this. It treats all pages past the one containing i_size as left behind
due to a previous truncate operation.
Thankfully, ocfs2 calculates the number of pages it will be working on
up front. The rest of the write code merely honors the original
calculation. We can simply trim the number of pages to only cover the
actual file data.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Cc: stable@kernel.org
Alan Ott [Wed, 30 Jun 2010 13:50:36 +0000 (09:50 -0400)]
HID: Send Report ID when numbered reports are sent over the control endpoint.
The Report ID wasn't sent as part of the payload for reports which were sent
over the control endpoint. This is required by section 8.1 of the HID spec.
Signed-off-by: Alan Ott <alan@signal11.us> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
V4L/DVB: uvc: Fix multiple symbols definitions with UVC gadget and host drivers
The UVC gadget driver borrowed code from the UVC host driver without
changing the symbol names. This results in a namespace clash with
multiple definitions of several symbols when compiling both drivers in
the kernel.
Make all generic UVC functions and variables static in the UVC gadget
driver, as the symbols are not referenced outside of the gadget driver.
Rename the uvc_trace_param global variable to uvc_gadget_trace_param.
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: Fix autoloading of fschmd on recent Fujitsu machines
hwmon: (coretemp) Properly label the sensors
hwmon: (coretemp) Skip duplicate CPU entries
hwmon: (it87) Fix in7 on IT8720F
hwmon: (k8temp) Fix temperature reporting for ASB1 processor revisions
Merge branch 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c/mips: Fix error return codes from Sibyte i2c bus driver
i2c: Fix probability check
Peter Edwards [Sun, 11 Jul 2010 16:45:50 +0000 (17:45 +0100)]
HID: Enable HID_QUIRK_MULTI_INPUT for Retro Adaptor
Patch for linux-2.6.35-rc4 mainline kernel to enable Paul Qureshi's
Retro Adapter [http://keio.dk/retroadapter.html], an open source USB
device which allows controllers and joysticks from classic computers
and consoles to work on modern PCs, to appear as two separate devices
under Linux. Signed-off-by: Peter Edwards <samwise@bagshot-row.org> Acked-by: Paul Qureshi <retro@world3.net> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
powerpc/fsl-booke: Fix address issue when using relocatable kernels
When booting a relocatable kernel it needs to jump to the correct
start address, which for BookE parts is usually unchanged
regardless of the physical memory offset.
Recent changes cause problems with how we calculate the start
address, it was always adding the RMO into the start address
which is incorrect. This patch only adds in the RMO offset
if we are in the kexec code path, as it needs the RMO to work
correctly.
Instead of adding the RMO offset in in the common code path, we
can just set r6 to the RMO offset in the kexec code path instead
of to zero, and finally perform the masking in the common code
path
Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Anton Vorontsov [Thu, 8 Jul 2010 17:16:16 +0000 (21:16 +0400)]
powerpc/cpm1: Mark micropatch code/data static and __init
This saves runtime memory and fixes lots of sparse warnings like this:
CHECK arch/powerpc/sysdev/micropatch.c
arch/powerpc/sysdev/micropatch.c:27:6: warning: symbol 'patch_2000'
was not declared. Should it be static?
arch/powerpc/sysdev/micropatch.c:146:6: warning: symbol 'patch_2f00'
was not declared. Should it be static?
...
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Anton Vorontsov [Thu, 8 Jul 2010 17:16:14 +0000 (21:16 +0400)]
powerpc/cpm1: Fix build with various CONFIG_*_UCODE_PATCH combinations
Warnings are treated as errors for arch/powerpc code, so build fails
with CONFIG_I2C_SPI_UCODE_PATCH=y:
CC arch/powerpc/sysdev/micropatch.o
cc1: warnings being treated as errors
arch/powerpc/sysdev/micropatch.c: In function 'cpm_load_patch':
arch/powerpc/sysdev/micropatch.c:630: warning: unused variable 'smp'
make[1]: *** [arch/powerpc/sysdev/micropatch.o] Error 1
And with CONFIG_USB_SOF_UCODE_PATCH=y:
CC arch/powerpc/sysdev/micropatch.o
cc1: warnings being treated as errors
arch/powerpc/sysdev/micropatch.c: In function 'cpm_load_patch':
arch/powerpc/sysdev/micropatch.c:629: warning: unused variable 'spp'
arch/powerpc/sysdev/micropatch.c:628: warning: unused variable 'iip'
make[1]: *** [arch/powerpc/sysdev/micropatch.o] Error 1
This patch fixes these issues by introducing proper #ifdefs.
Cc: <stable@kernel.org> [ .33, .34 ] Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Anton Vorontsov [Thu, 8 Jul 2010 17:16:10 +0000 (21:16 +0400)]
powerpc/cpm: Reintroduce global spi_pram struct (fixes build issue)
spi_t was removed in commit 644b2a680ccc51a9ec4d6beb12e9d47d2dee98e2
("powerpc/cpm: Remove SPI defines and spi structs"), the commit assumed
that spi_t isn't used anywhere outside of the spi_mpc8xxx driver. But
it appears that the struct is needed for micropatch code. So, let's
reintroduce the struct.
Fixes the following build issue:
CC arch/powerpc/sysdev/micropatch.o
micropatch.c: In function 'cpm_load_patch':
micropatch.c:629: error: expected '=', ',', ';', 'asm' or '__attribute__' before '*' token
micropatch.c:629: error: 'spp' undeclared (first use in this function)
micropatch.c:629: error: (Each undeclared identifier is reported only once
micropatch.c:629: error: for each function it appears in.)
Reported-by: LEROY Christophe <christophe.leroy@c-s.fr> Reported-by: Tony Breeds <tony@bakeyournoodle.com> Cc: <stable@kernel.org> [ .33, .34 ] Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Russell King [Sat, 10 Jul 2010 09:10:18 +0000 (10:10 +0100)]
ARM: lockdep: fix unannotated irqs-on
CPU: Testing write buffer coherency: ok
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:3145 check_flags+0xcc/0x1dc()
Modules linked in:
[<c0035120>] (unwind_backtrace+0x0/0xf8) from [<c0355374>] (dump_stack+0x20/0x24)
[<c0355374>] (dump_stack+0x20/0x24) from [<c0060c04>] (warn_slowpath_common+0x58/0x70)
[<c0060c04>] (warn_slowpath_common+0x58/0x70) from [<c0060c3c>] (warn_slowpath_null+0x20/0x24)
[<c0060c3c>] (warn_slowpath_null+0x20/0x24) from [<c008f224>] (check_flags+0xcc/0x1dc)
[<c008f224>] (check_flags+0xcc/0x1dc) from [<c00945dc>] (lock_acquire+0x50/0x140)
[<c00945dc>] (lock_acquire+0x50/0x140) from [<c0358434>] (_raw_spin_lock+0x50/0x88)
[<c0358434>] (_raw_spin_lock+0x50/0x88) from [<c00fd114>] (set_task_comm+0x2c/0x60)
[<c00fd114>] (set_task_comm+0x2c/0x60) from [<c007e184>] (kthreadd+0x30/0x108)
[<c007e184>] (kthreadd+0x30/0x108) from [<c0030104>] (kernel_thread_exit+0x0/0x8)
---[ end trace 1b75b31a2719ed1c ]---
possible reason: unannotated irqs-on.
irq event stamp: 3
hardirqs last enabled at (2): [<c0059bb0>] finish_task_switch+0x48/0xb0
hardirqs last disabled at (3): [<c002f0b0>] ret_slow_syscall+0xc/0x1c
softirqs last enabled at (0): [<c005f3e0>] copy_process+0x394/0xe5c
softirqs last disabled at (0): [<(null)>] (null)
Fix this by ensuring that the lockdep interrupt state is manipulated in
the appropriate places. We essentially treat userspace as an entirely
separate environment which isn't relevant to lockdep (lockdep doesn't
monitor userspace.) We don't tell lockdep that IRQs will be enabled
in that environment.
Instead, when creating kernel threads (which is a rare event compared
to entering/leaving userspace) we have to update the lockdep state. Do
this by starting threads with IRQs disabled, and in the kthread helper,
tell lockdep that IRQs are enabled, and enable them.
This provides lockdep with a consistent view of the current IRQ state
in kernel space.
Steven Rostedt [Fri, 9 Jul 2010 19:41:44 +0000 (15:41 -0400)]
tracing: Add alignment to syscall metadata declarations
For some reason if we declare a static variable and then assign it
later, and the assignment contains a __attribute__((__aligned__(#))),
some versions of gcc will ignore it.
This caused the syscall meta data to not be compact in its section
and caused a kernel oops when the section was being read.
The fix for these versions of gcc seems to be to add the aligned
attribute to the declaration as well.
Jean Delvare [Fri, 9 Jul 2010 14:22:51 +0000 (16:22 +0200)]
hwmon: Fix autoloading of fschmd on recent Fujitsu machines
Fujitsu slightly changed the DMI strings in their recent machines,
(for example the D2778) and this breaks the automatic loading of the
needed fschmd driver. Being more tolerant on string comparison fixes
the issue.
This closes bug #15634:
https://bugzilla.kernel.org/show_bug.cgi?id=15634
Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: Sergey Spiridonov <sena@hurd.homeunix.org> Cc: Hans de Goede <hdegoede@redhat.com>
Jean Delvare [Fri, 9 Jul 2010 14:22:48 +0000 (16:22 +0200)]
hwmon: (it87) Fix in7 on IT8720F
The IT8720F has no VIN7 pin, so VCCH should always be routed
internally to VIN7 with an internal divider. Curiously, there still
is a configuration bit to control this, which means it can be set
incorrectly. And even more curiously, many boards out there are
improperly configured, even though the IT8720F datasheet claims that
the internal routing of VCCH to VIN7 is the default setting. So we
force the internal routing in this case.
It turns out that all boards with the wrong setting are from Gigabyte,
so I suspect a BIOS bug. But it's easy enough to workaround in the
driver, so let's do it.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Jean-Marc Spaggiari <jean-marc@spaggiari.org> Cc: stable@kernel.org
hwmon: (k8temp) Fix temperature reporting for ASB1 processor revisions
Reported temperature for ASB1 CPUs is too high.
Add ASB1 CPU revisions (these are also non-desktop variants) to the
list of CPUs for which the temperature fixup is not required.
Example: (from LENOVO ThinkPad Edge 13, 01972NG, system was idle)
Current kernel reports
$ sensors
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +74.0 C
Core0 Temp: +70.0 C
Core1 Temp: +69.0 C
Core1 Temp: +70.0 C
With this patch I have
$ sensors
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +54.0 C
Core0 Temp: +51.0 C
Core1 Temp: +48.0 C
Core1 Temp: +49.0 C
Cc: stable@kernel.org [.32.x .33.x, .34.x] Cc: Rudolf Marek <r.marek@assembler.cz> Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Will Deacon [Thu, 8 Jul 2010 09:59:16 +0000 (10:59 +0100)]
ARM: 6212/1: atomic ops: add memory constraints to inline asm
Currently, the 32-bit and 64-bit atomic operations on ARM do not
include memory constraints in the inline assembly blocks. In the
case of barrier-less operations [for example, atomic_add], this
means that the compiler may constant fold values which have actually
been modified by a call to an atomic operation.
This issue can be observed in the atomic64_test routine in
<kernel root>/lib/atomic64_test.c:
The atomic64_set (0x38-0x44) writes to the atomic64_t, but the
compiler doesn't see this, assumes the test condition is always
false and generates an unconditional branch to __bug. The rest of the
test is optimised away.
This patch adds suitable memory constraints to the atomic operations on ARM
to ensure that the compiler is informed of the correct data hazards. We have
to use the "Qo" constraints to avoid hitting the GCC anomaly described at
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=44492 , where the compiler
makes assumptions about the writeback in the addressing mode used by the
inline assembly. These constraints forbid the use of auto{inc,dec} addressing
modes, so it doesn't matter if we don't use the operand exactly once.
Cc: stable@kernel.org Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Thu, 8 Jul 2010 09:58:06 +0000 (10:58 +0100)]
ARM: 6211/1: atomic ops: fix register constraints for atomic64_add_unless
The atomic64_add_unless function compares an atomic variable with
a given value and, if they are not equal, adds another given value
to the atomic variable. The function returns zero if the addition
did not occur and non-zero otherwise.
On ARM, the return value is initialised to 1 in C code. Inline assembly
code then performs the atomic64_add_unless operation, setting the
return value to 0 iff the addition does not occur. This means that
when the addition *does* occur, the value of ret must be preserved
across the inline assembly and therefore requires a "+r" constraint
rather than the current one of "=&r".
Thanks to Nicolas Pitre for helping to spot this.
Cc: stable@kernel.org Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM: 6210/1: Do not rely on reset defaults of L2X0_AUX_CTRL
On i.MX35 the L2X0_AUX_CTRL register does not have sensible reset
default values. Allow them to be overwritten with the aux_val/aux_mask
arguments passed to l2x0_init().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ALSA: hda - Restore cleared pin controls on resume
Many codecs now clear the pin controls at suspend via snd_hda_shutup_pins()
for reducing the click noise at power-off. But this leaves some pins
uninitialized, and they'll be never recovered after resume.
This patch adds the proper recovery of cleared pin controls on resume.
Also it adds a check of bus->shutdown so that pins won't be cleared at
module unloading.
Sage Weil [Thu, 8 Jul 2010 17:47:16 +0000 (10:47 -0700)]
ceph: fix printing of ipv6 addrs
The buffer was too small. Make it bigger, use snprintf(), put brackets
around the ipv6 address to avoid mixing it up with the :port, and use the
ever-so-handy %pI[46] formats.
Johan Hedberg [Fri, 18 Jun 2010 08:08:56 +0000 (11:08 +0300)]
Bluetooth: Reset the security level after an authentication failure
When authentication fails for a connection the assumed security level
should be set back to BT_SECURITY_LOW so that subsequent connect
attempts over the same link don't falsely assume that security is
adequate enough.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Check L2CAP pending status before sending connect request
Due to race condition in L2CAP state machine L2CAP Connection Request
may be sent twice for SDP with the same source channel id. Problems
reported connecting to Apple products, some carkit, Blackberry phones.
Ben Hutchings [Thu, 1 Jul 2010 20:37:20 +0000 (20:37 +0000)]
IB/qib: Use request_firmware() to load SD7220 firmware
Extract the microcode for the QLogic QLE7220 series IB HCA and use the
kernel microcode request facility to load the microcode. This
supports Debian Linux's requirements to separate microcode which
doesn't have open source code available from the device driver.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Joel Becker [Thu, 1 Jul 2010 22:13:31 +0000 (15:13 -0700)]
ocfs2: Zero the tail cluster when extending past i_size.
ocfs2's allocation unit is the cluster. This can be larger than a block
or even a memory page. This means that a file may have many blocks in
its last extent that are beyond the block containing i_size. There also
may be more unwritten extents after that.
When ocfs2 grows a file, it zeros the entire cluster in order to ensure
future i_size growth will see cleared blocks. Unfortunately,
block_write_full_page() drops the pages past i_size. This means that
ocfs2 is actually leaking garbage data into the tail end of that last
cluster. This is a bug.
We adjust ocfs2_write_begin_nolock() and ocfs2_extend_file() to detect
when a write or truncate is past i_size. They will use
ocfs2_zero_extend() to ensure the data is properly zeroed.
Older versions of ocfs2_zero_extend() simply zeroed every block between
i_size and the zeroing position. This presumes three things:
1) There is allocation for all of these blocks.
2) The extents are not unwritten.
3) The extents are not refcounted.
(1) and (2) hold true for non-sparse filesystems, which used to be the
only users of ocfs2_zero_extend(). (3) is another bug.
Since we're now using ocfs2_zero_extend() for sparse filesystems as
well, we teach ocfs2_zero_extend() to check every extent between
i_size and the zeroing position. If the extent is unwritten, it is
ignored. If it is refcounted, it is CoWed. Then it is zeroed.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Cc: stable@kernel.org
Joel Becker [Tue, 6 Jul 2010 21:36:06 +0000 (14:36 -0700)]
ocfs2: When zero extending, do it by page.
ocfs2_zero_extend() does its zeroing block by block, but it calls a
function named ocfs2_write_zero_page(). Let's have
ocfs2_write_zero_page() handle the page level. From
ocfs2_zero_extend()'s perspective, it is now page-at-a-time.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Cc: stable@kernel.org
V4L/DVB: uvcvideo: Power line frequency control doesn't support GET_MIN/MAX/RES
Issuing a GET_MIN request on the power line frequency control times out
on at least the Apple iSight. As the UVC specification doesn't list
GET_MIN/MAX/RES as supported on that control, remove them from the
uvc_ctrls array.
Andy Walls [Sat, 12 Jun 2010 23:24:24 +0000 (20:24 -0300)]
V4L/DVB: tveeprom: Add an entry for tuner code 168: a TCL M30WTP-4N-E tuner
Hauppauge EEPROM tuner code 168 has recently shown up on HVR-1600 TV
capture cards supported by the cx18 driver. This change allows analog
tuner type autodetection to succeed for these cards.
Information for decoding tuner code 168 was provided by Hauppauge.
Signed-off-by: Andy Walls <awalls@md.metrocast.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
git://bbs.cooldavid.org / net-next-2.6.git / log