--- /dev/null
+/*
+ * New driver for Marvell Yukon chipset and SysKonnect Gigabit
+ * Ethernet adapters. Based on earlier sk98lin, e100 and
+ * FreeBSD if_sk drivers.
+ *
+ * This driver intentionally does not support all the features
+ * of the original driver such as link fail-over and link management because
+ * those should be done at higher levels.
+ *
+ * Copyright (C) 2004, Stephen Hemminger <shemminger@osdl.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/pci.h>
+#include <linux/if_vlan.h>
+#include <linux/ip.h>
+#include <linux/delay.h>
+#include <linux/crc32.h>
+#include <asm/irq.h>
+
+#include "skge.h"
+
+#define DRV_NAME "skge"
+#define DRV_VERSION "0.6"
+#define PFX DRV_NAME " "
+
+#define DEFAULT_TX_RING_SIZE 128
+#define DEFAULT_RX_RING_SIZE 512
+#define MAX_TX_RING_SIZE 1024
+#define MAX_RX_RING_SIZE 4096
+#define PHY_RETRIES 1000
+#define ETH_JUMBO_MTU 9000
+#define TX_WATCHDOG (5 * HZ)
+#define NAPI_WEIGHT 64
+#define BLINK_HZ (HZ/4)
+#define LINK_POLL_HZ (HZ/10)
+
+MODULE_DESCRIPTION("SysKonnect Gigabit Ethernet driver");
+MODULE_AUTHOR("Stephen Hemminger <shemminger@osdl.org>");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
+
+static const u32 default_msg
+ = NETIF_MSG_DRV| NETIF_MSG_PROBE| NETIF_MSG_LINK
+ | NETIF_MSG_IFUP| NETIF_MSG_IFDOWN;
+
+static int debug = -1; /* defaults above */
+module_param(debug, int, 0);
+MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
+
+static const struct pci_device_id skge_id_table[] = {
+ { PCI_VENDOR_ID_3COM, PCI_DEVICE_ID_3COM_3C940,
+ PCI_ANY_ID, PCI_ANY_ID },
+ { PCI_VENDOR_ID_3COM, PCI_DEVICE_ID_3COM_3C940B,
+ PCI_ANY_ID, PCI_ANY_ID },
+ { PCI_VENDOR_ID_SYSKONNECT, PCI_DEVICE_ID_SYSKONNECT_GE,
+ PCI_ANY_ID, PCI_ANY_ID },
+ { PCI_VENDOR_ID_SYSKONNECT, PCI_DEVICE_ID_SYSKONNECT_YU,
+ PCI_ANY_ID, PCI_ANY_ID },
+ { PCI_VENDOR_ID_SYSKONNECT, 0x9E00, /* SK-9Exx */
+ PCI_ANY_ID, PCI_ANY_ID },
+ { PCI_VENDOR_ID_DLINK, PCI_DEVICE_ID_DLINK_DGE510T,
+ PCI_ANY_ID, PCI_ANY_ID },
+ { PCI_VENDOR_ID_MARVELL, 0x4320, /* Gigabit Ethernet Controller */
+ PCI_ANY_ID, PCI_ANY_ID },
+ { PCI_VENDOR_ID_MARVELL, 0x5005, /* Marvell (11ab), Belkin */
+ PCI_ANY_ID, PCI_ANY_ID },
+ { PCI_VENDOR_ID_CNET, PCI_DEVICE_ID_CNET_GIGACARD,
+ PCI_ANY_ID, PCI_ANY_ID },
+ { PCI_VENDOR_ID_LINKSYS, PCI_DEVICE_ID_LINKSYS_EG1032,
+ PCI_ANY_ID, PCI_ANY_ID },
+ { PCI_VENDOR_ID_LINKSYS, PCI_DEVICE_ID_LINKSYS_EG1064,
+ PCI_ANY_ID, PCI_ANY_ID },
+ { 0 }
+};
+MODULE_DEVICE_TABLE(pci, skge_id_table);
+
+static int skge_up(struct net_device *dev);
+static int skge_down(struct net_device *dev);
+static void skge_tx_clean(struct skge_port *skge);
+static void skge_xm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val);
+static void skge_gm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val);
+static void genesis_get_stats(struct skge_port *skge, u64 *data);
+static void yukon_get_stats(struct skge_port *skge, u64 *data);
+static void yukon_init(struct skge_hw *hw, int port);
+static void yukon_reset(struct skge_hw *hw, int port);
+static void genesis_mac_init(struct skge_hw *hw, int port);
+static void genesis_reset(struct skge_hw *hw, int port);
+
+static const int txqaddr[] = { Q_XA1, Q_XA2 };
+static const int rxqaddr[] = { Q_R1, Q_R2 };
+static const u32 rxirqmask[] = { IS_R1_F, IS_R2_F };
+static const u32 txirqmask[] = { IS_XA1_F, IS_XA2_F };
+
+/* Don't need to look at whole 16K.
+ * last interesting register is descriptor poll timer.
+ */
+#define SKGE_REGS_LEN (29*128)
+
+static int skge_get_regs_len(struct net_device *dev)
+{
+ return SKGE_REGS_LEN;
+}
+
+/*
+ * Returns copy of control register region
+ * I/O region is divided into banks and certain regions are unreadable
+ */
+static void skge_get_regs(struct net_device *dev, struct ethtool_regs *regs,
+ void *p)
+{
+ const struct skge_port *skge = netdev_priv(dev);
+ unsigned long offs;
+ const void __iomem *io = skge->hw->regs;
+ static const unsigned long bankmap
+ = (1<<0) | (1<<2) | (1<<8) | (1<<9)
+ | (1<<12) | (1<<13) | (1<<14) | (1<<15) | (1<<16)
+ | (1<<17) | (1<<20) | (1<<21) | (1<<22) | (1<<23)
+ | (1<<24) | (1<<25) | (1<<26) | (1<<27) | (1<<28);
+
+ regs->version = 1;
+ for (offs = 0; offs < regs->len; offs += 128) {
+ u32 len = min_t(u32, 128, regs->len - offs);
+
+ if (bankmap & (1<<(offs/128)))
+ memcpy_fromio(p + offs, io + offs, len);
+ else
+ memset(p + offs, 0, len);
+ }
+}
+
+/* Wake on Lan only supported on Yukon chps with rev 1 or above */
+static int wol_supported(const struct skge_hw *hw)
+{
+ return !((hw->chip_id == CHIP_ID_GENESIS ||
+ (hw->chip_id == CHIP_ID_YUKON && chip_rev(hw) == 0)));
+}
+
+static void skge_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ wol->supported = wol_supported(skge->hw) ? WAKE_MAGIC : 0;
+ wol->wolopts = skge->wol ? WAKE_MAGIC : 0;
+}
+
+static int skge_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+
+ if(wol->wolopts != WAKE_MAGIC && wol->wolopts != 0)
+ return -EOPNOTSUPP;
+
+ if (wol->wolopts == WAKE_MAGIC && !wol_supported(hw))
+ return -EOPNOTSUPP;
+
+ skge->wol = wol->wolopts == WAKE_MAGIC;
+
+ if (skge->wol) {
+ memcpy_toio(hw->regs + WOL_MAC_ADDR, dev->dev_addr, ETH_ALEN);
+
+ skge_write16(hw, WOL_CTRL_STAT,
+ WOL_CTL_ENA_PME_ON_MAGIC_PKT |
+ WOL_CTL_ENA_MAGIC_PKT_UNIT);
+ } else
+ skge_write16(hw, WOL_CTRL_STAT, WOL_CTL_DEFAULT);
+
+ return 0;
+}
+
+
+static int skge_get_settings(struct net_device *dev,
+ struct ethtool_cmd *ecmd)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+
+ ecmd->transceiver = XCVR_INTERNAL;
+
+ if (iscopper(hw)) {
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ ecmd->supported = SUPPORTED_1000baseT_Full
+ | SUPPORTED_1000baseT_Half
+ | SUPPORTED_Autoneg | SUPPORTED_TP;
+ else {
+ ecmd->supported = SUPPORTED_10baseT_Half
+ | SUPPORTED_10baseT_Full
+ | SUPPORTED_100baseT_Half
+ | SUPPORTED_100baseT_Full
+ | SUPPORTED_1000baseT_Half
+ | SUPPORTED_1000baseT_Full
+ | SUPPORTED_Autoneg| SUPPORTED_TP;
+
+ if (hw->chip_id == CHIP_ID_YUKON)
+ ecmd->supported &= ~SUPPORTED_1000baseT_Half;
+
+ else if (hw->chip_id == CHIP_ID_YUKON_FE)
+ ecmd->supported &= ~(SUPPORTED_1000baseT_Half
+ | SUPPORTED_1000baseT_Full);
+ }
+
+ ecmd->port = PORT_TP;
+ ecmd->phy_address = hw->phy_addr;
+ } else {
+ ecmd->supported = SUPPORTED_1000baseT_Full
+ | SUPPORTED_FIBRE
+ | SUPPORTED_Autoneg;
+
+ ecmd->port = PORT_FIBRE;
+ }
+
+ ecmd->advertising = skge->advertising;
+ ecmd->autoneg = skge->autoneg;
+ ecmd->speed = skge->speed;
+ ecmd->duplex = skge->duplex;
+ return 0;
+}
+
+static u32 skge_modes(const struct skge_hw *hw)
+{
+ u32 modes = ADVERTISED_Autoneg
+ | ADVERTISED_1000baseT_Full | ADVERTISED_1000baseT_Half
+ | ADVERTISED_100baseT_Full | ADVERTISED_100baseT_Half
+ | ADVERTISED_10baseT_Full | ADVERTISED_10baseT_Half;
+
+ if (iscopper(hw)) {
+ modes |= ADVERTISED_TP;
+ switch(hw->chip_id) {
+ case CHIP_ID_GENESIS:
+ modes &= ~(ADVERTISED_100baseT_Full
+ | ADVERTISED_100baseT_Half
+ | ADVERTISED_10baseT_Full
+ | ADVERTISED_10baseT_Half);
+ break;
+
+ case CHIP_ID_YUKON:
+ modes &= ~ADVERTISED_1000baseT_Half;
+ break;
+
+ case CHIP_ID_YUKON_FE:
+ modes &= ~(ADVERTISED_1000baseT_Half|ADVERTISED_1000baseT_Full);
+ break;
+ }
+ } else {
+ modes |= ADVERTISED_FIBRE;
+ modes &= ~ADVERTISED_1000baseT_Half;
+ }
+ return modes;
+}
+
+static int skge_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ const struct skge_hw *hw = skge->hw;
+
+ if (ecmd->autoneg == AUTONEG_ENABLE) {
+ if (ecmd->advertising & skge_modes(hw))
+ return -EINVAL;
+ } else {
+ switch(ecmd->speed) {
+ case SPEED_1000:
+ if (hw->chip_id == CHIP_ID_YUKON_FE)
+ return -EINVAL;
+ break;
+ case SPEED_100:
+ case SPEED_10:
+ if (iscopper(hw) || hw->chip_id == CHIP_ID_GENESIS)
+ return -EINVAL;
+ break;
+ default:
+ return -EINVAL;
+ }
+ }
+
+ skge->autoneg = ecmd->autoneg;
+ skge->speed = ecmd->speed;
+ skge->duplex = ecmd->duplex;
+ skge->advertising = ecmd->advertising;
+
+ if (netif_running(dev)) {
+ skge_down(dev);
+ skge_up(dev);
+ }
+ return (0);
+}
+
+static void skge_get_drvinfo(struct net_device *dev,
+ struct ethtool_drvinfo *info)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ strcpy(info->driver, DRV_NAME);
+ strcpy(info->version, DRV_VERSION);
+ strcpy(info->fw_version, "N/A");
+ strcpy(info->bus_info, pci_name(skge->hw->pdev));
+}
+
+static const struct skge_stat {
+ char name[ETH_GSTRING_LEN];
+ u16 xmac_offset;
+ u16 gma_offset;
+} skge_stats[] = {
+ { "tx_bytes", XM_TXO_OK_HI, GM_TXO_OK_HI },
+ { "rx_bytes", XM_RXO_OK_HI, GM_RXO_OK_HI },
+
+ { "tx_broadcast", XM_TXF_BC_OK, GM_TXF_BC_OK },
+ { "rx_broadcast", XM_RXF_BC_OK, GM_RXF_BC_OK },
+ { "tx_multicast", XM_TXF_MC_OK, GM_TXF_MC_OK },
+ { "rx_multicast", XM_RXF_MC_OK, GM_RXF_MC_OK },
+ { "tx_unicast", XM_TXF_UC_OK, GM_TXF_UC_OK },
+ { "rx_unicast", XM_RXF_UC_OK, GM_RXF_UC_OK },
+ { "tx_mac_pause", XM_TXF_MPAUSE, GM_TXF_MPAUSE },
+ { "rx_mac_pause", XM_RXF_MPAUSE, GM_RXF_MPAUSE },
+
+ { "collisions", XM_TXF_SNG_COL, GM_TXF_SNG_COL },
+ { "multi_collisions", XM_TXF_MUL_COL, GM_TXF_MUL_COL },
+ { "aborted", XM_TXF_ABO_COL, GM_TXF_ABO_COL },
+ { "late_collision", XM_TXF_LAT_COL, GM_TXF_LAT_COL },
+ { "fifo_underrun", XM_TXE_FIFO_UR, GM_TXE_FIFO_UR },
+ { "fifo_overflow", XM_RXE_FIFO_OV, GM_RXE_FIFO_OV },
+
+ { "rx_toolong", XM_RXF_LNG_ERR, GM_RXF_LNG_ERR },
+ { "rx_jabber", XM_RXF_JAB_PKT, GM_RXF_JAB_PKT },
+ { "rx_runt", XM_RXE_RUNT, GM_RXE_FRAG },
+ { "rx_too_long", XM_RXF_LNG_ERR, GM_RXF_LNG_ERR },
+ { "rx_fcs_error", XM_RXF_FCS_ERR, GM_RXF_FCS_ERR },
+};
+
+static int skge_get_stats_count(struct net_device *dev)
+{
+ return ARRAY_SIZE(skge_stats);
+}
+
+static void skge_get_ethtool_stats(struct net_device *dev,
+ struct ethtool_stats *stats, u64 *data)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ if (skge->hw->chip_id == CHIP_ID_GENESIS)
+ genesis_get_stats(skge, data);
+ else
+ yukon_get_stats(skge, data);
+}
+
+/* Use hardware MIB variables for critical path statistics and
+ * transmit feedback not reported at interrupt.
+ * Other errors are accounted for in interrupt handler.
+ */
+static struct net_device_stats *skge_get_stats(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ u64 data[ARRAY_SIZE(skge_stats)];
+
+ if (skge->hw->chip_id == CHIP_ID_GENESIS)
+ genesis_get_stats(skge, data);
+ else
+ yukon_get_stats(skge, data);
+
+ skge->net_stats.tx_bytes = data[0];
+ skge->net_stats.rx_bytes = data[1];
+ skge->net_stats.tx_packets = data[2] + data[4] + data[6];
+ skge->net_stats.rx_packets = data[3] + data[5] + data[7];
+ skge->net_stats.multicast = data[5] + data[7];
+ skge->net_stats.collisions = data[10];
+ skge->net_stats.tx_aborted_errors = data[12];
+
+ return &skge->net_stats;
+}
+
+static void skge_get_strings(struct net_device *dev, u32 stringset, u8 *data)
+{
+ int i;
+
+ switch(stringset) {
+ case ETH_SS_STATS:
+ for (i = 0; i < ARRAY_SIZE(skge_stats); i++)
+ memcpy(data + i * ETH_GSTRING_LEN,
+ skge_stats[i].name, ETH_GSTRING_LEN);
+ break;
+ }
+}
+
+static void skge_get_ring_param(struct net_device *dev,
+ struct ethtool_ringparam *p)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ p->rx_max_pending = MAX_RX_RING_SIZE;
+ p->tx_max_pending = MAX_TX_RING_SIZE;
+ p->rx_mini_max_pending = 0;
+ p->rx_jumbo_max_pending = 0;
+
+ p->rx_pending = skge->rx_ring.count;
+ p->tx_pending = skge->tx_ring.count;
+ p->rx_mini_pending = 0;
+ p->rx_jumbo_pending = 0;
+}
+
+static int skge_set_ring_param(struct net_device *dev,
+ struct ethtool_ringparam *p)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ if (p->rx_pending == 0 || p->rx_pending > MAX_RX_RING_SIZE ||
+ p->tx_pending == 0 || p->tx_pending > MAX_TX_RING_SIZE)
+ return -EINVAL;
+
+ skge->rx_ring.count = p->rx_pending;
+ skge->tx_ring.count = p->tx_pending;
+
+ if (netif_running(dev)) {
+ skge_down(dev);
+ skge_up(dev);
+ }
+
+ return 0;
+}
+
+static u32 skge_get_msglevel(struct net_device *netdev)
+{
+ struct skge_port *skge = netdev_priv(netdev);
+ return skge->msg_enable;
+}
+
+static void skge_set_msglevel(struct net_device *netdev, u32 value)
+{
+ struct skge_port *skge = netdev_priv(netdev);
+ skge->msg_enable = value;
+}
+
+static int skge_nway_reset(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+
+ if (skge->autoneg != AUTONEG_ENABLE || !netif_running(dev))
+ return -EINVAL;
+
+ spin_lock_bh(&hw->phy_lock);
+ if (hw->chip_id == CHIP_ID_GENESIS) {
+ genesis_reset(hw, port);
+ genesis_mac_init(hw, port);
+ } else {
+ yukon_reset(hw, port);
+ yukon_init(hw, port);
+ }
+ spin_unlock_bh(&hw->phy_lock);
+ return 0;
+}
+
+static int skge_set_sg(struct net_device *dev, u32 data)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+
+ if (hw->chip_id == CHIP_ID_GENESIS && data)
+ return -EOPNOTSUPP;
+ return ethtool_op_set_sg(dev, data);
+}
+
+static int skge_set_tx_csum(struct net_device *dev, u32 data)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+
+ if (hw->chip_id == CHIP_ID_GENESIS && data)
+ return -EOPNOTSUPP;
+
+ return ethtool_op_set_tx_csum(dev, data);
+}
+
+static u32 skge_get_rx_csum(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ return skge->rx_csum;
+}
+
+/* Only Yukon supports checksum offload. */
+static int skge_set_rx_csum(struct net_device *dev, u32 data)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ if (skge->hw->chip_id == CHIP_ID_GENESIS && data)
+ return -EOPNOTSUPP;
+
+ skge->rx_csum = data;
+ return 0;
+}
+
+/* Only Yukon II supports TSO (not implemented yet) */
+static int skge_set_tso(struct net_device *dev, u32 data)
+{
+ if (data)
+ return -EOPNOTSUPP;
+ return 0;
+}
+
+static void skge_get_pauseparam(struct net_device *dev,
+ struct ethtool_pauseparam *ecmd)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ ecmd->tx_pause = (skge->flow_control == FLOW_MODE_LOC_SEND)
+ || (skge->flow_control == FLOW_MODE_SYMMETRIC);
+ ecmd->rx_pause = (skge->flow_control == FLOW_MODE_REM_SEND)
+ || (skge->flow_control == FLOW_MODE_SYMMETRIC);
+
+ ecmd->autoneg = skge->autoneg;
+}
+
+static int skge_set_pauseparam(struct net_device *dev,
+ struct ethtool_pauseparam *ecmd)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ skge->autoneg = ecmd->autoneg;
+ if (ecmd->rx_pause && ecmd->tx_pause)
+ skge->flow_control = FLOW_MODE_SYMMETRIC;
+ else if(ecmd->rx_pause && !ecmd->tx_pause)
+ skge->flow_control = FLOW_MODE_REM_SEND;
+ else if(!ecmd->rx_pause && ecmd->tx_pause)
+ skge->flow_control = FLOW_MODE_LOC_SEND;
+ else
+ skge->flow_control = FLOW_MODE_NONE;
+
+ if (netif_running(dev)) {
+ skge_down(dev);
+ skge_up(dev);
+ }
+ return 0;
+}
+
+/* Chip internal frequency for clock calculations */
+static inline u32 hwkhz(const struct skge_hw *hw)
+{
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ return 53215; /* or: 53.125 MHz */
+ else if (hw->chip_id == CHIP_ID_YUKON_EC)
+ return 125000; /* or: 125.000 MHz */
+ else
+ return 78215; /* or: 78.125 MHz */
+}
+
+/* Chip hz to microseconds */
+static inline u32 skge_clk2usec(const struct skge_hw *hw, u32 ticks)
+{
+ return (ticks * 1000) / hwkhz(hw);
+}
+
+/* Microseconds to chip hz */
+static inline u32 skge_usecs2clk(const struct skge_hw *hw, u32 usec)
+{
+ return hwkhz(hw) * usec / 1000;
+}
+
+static int skge_get_coalesce(struct net_device *dev,
+ struct ethtool_coalesce *ecmd)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+
+ ecmd->rx_coalesce_usecs = 0;
+ ecmd->tx_coalesce_usecs = 0;
+
+ if (skge_read32(hw, B2_IRQM_CTRL) & TIM_START) {
+ u32 delay = skge_clk2usec(hw, skge_read32(hw, B2_IRQM_INI));
+ u32 msk = skge_read32(hw, B2_IRQM_MSK);
+
+ if (msk & rxirqmask[port])
+ ecmd->rx_coalesce_usecs = delay;
+ if (msk & txirqmask[port])
+ ecmd->tx_coalesce_usecs = delay;
+ }
+
+ return 0;
+}
+
+/* Note: interrupt timer is per board, but can turn on/off per port */
+static int skge_set_coalesce(struct net_device *dev,
+ struct ethtool_coalesce *ecmd)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u32 msk = skge_read32(hw, B2_IRQM_MSK);
+ u32 delay = 25;
+
+ if (ecmd->rx_coalesce_usecs == 0)
+ msk &= ~rxirqmask[port];
+ else if (ecmd->rx_coalesce_usecs < 25 ||
+ ecmd->rx_coalesce_usecs > 33333)
+ return -EINVAL;
+ else {
+ msk |= rxirqmask[port];
+ delay = ecmd->rx_coalesce_usecs;
+ }
+
+ if (ecmd->tx_coalesce_usecs == 0)
+ msk &= ~txirqmask[port];
+ else if (ecmd->tx_coalesce_usecs < 25 ||
+ ecmd->tx_coalesce_usecs > 33333)
+ return -EINVAL;
+ else {
+ msk |= txirqmask[port];
+ delay = min(delay, ecmd->rx_coalesce_usecs);
+ }
+
+ skge_write32(hw, B2_IRQM_MSK, msk);
+ if (msk == 0)
+ skge_write32(hw, B2_IRQM_CTRL, TIM_STOP);
+ else {
+ skge_write32(hw, B2_IRQM_INI, skge_usecs2clk(hw, delay));
+ skge_write32(hw, B2_IRQM_CTRL, TIM_START);
+ }
+ return 0;
+}
+
+static void skge_led_on(struct skge_hw *hw, int port)
+{
+ if (hw->chip_id == CHIP_ID_GENESIS) {
+ skge_write8(hw, SKGEMAC_REG(port, LNK_LED_REG), LINKLED_ON);
+ skge_write8(hw, B0_LED, LED_STAT_ON);
+
+ skge_write8(hw, SKGEMAC_REG(port, RX_LED_TST), LED_T_ON);
+ skge_write32(hw, SKGEMAC_REG(port, RX_LED_VAL), 100);
+ skge_write8(hw, SKGEMAC_REG(port, RX_LED_CTRL), LED_START);
+
+ switch (hw->phy_type) {
+ case SK_PHY_BCOM:
+ skge_xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL,
+ PHY_B_PEC_LED_ON);
+ break;
+ case SK_PHY_LONE:
+ skge_xm_phy_write(hw, port, PHY_LONE_LED_CFG,
+ 0x0800);
+ break;
+ default:
+ skge_write8(hw, SKGEMAC_REG(port, TX_LED_TST), LED_T_ON);
+ skge_write32(hw, SKGEMAC_REG(port, TX_LED_VAL), 100);
+ skge_write8(hw, SKGEMAC_REG(port, TX_LED_CTRL), LED_START);
+ }
+ } else {
+ skge_gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0);
+ skge_gm_phy_write(hw, port, PHY_MARV_LED_OVER,
+ PHY_M_LED_MO_DUP(MO_LED_ON) |
+ PHY_M_LED_MO_10(MO_LED_ON) |
+ PHY_M_LED_MO_100(MO_LED_ON) |
+ PHY_M_LED_MO_1000(MO_LED_ON) |
+ PHY_M_LED_MO_RX(MO_LED_ON));
+ }
+}
+
+static void skge_led_off(struct skge_hw *hw, int port)
+{
+ if (hw->chip_id == CHIP_ID_GENESIS) {
+ skge_write8(hw, SKGEMAC_REG(port, LNK_LED_REG), LINKLED_OFF);
+ skge_write8(hw, B0_LED, LED_STAT_OFF);
+
+ skge_write32(hw, SKGEMAC_REG(port, RX_LED_VAL), 0);
+ skge_write8(hw, SKGEMAC_REG(port, RX_LED_CTRL), LED_T_OFF);
+
+ switch (hw->phy_type) {
+ case SK_PHY_BCOM:
+ skge_xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL,
+ PHY_B_PEC_LED_OFF);
+ break;
+ case SK_PHY_LONE:
+ skge_xm_phy_write(hw, port, PHY_LONE_LED_CFG,
+ PHY_L_LC_LEDT);
+ break;
+ default:
+ skge_write32(hw, SKGEMAC_REG(port, TX_LED_VAL), 0);
+ skge_write8(hw, SKGEMAC_REG(port, TX_LED_CTRL), LED_T_OFF);
+ }
+ } else {
+ skge_gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0);
+ skge_gm_phy_write(hw, port, PHY_MARV_LED_OVER,
+ PHY_M_LED_MO_DUP(MO_LED_OFF) |
+ PHY_M_LED_MO_10(MO_LED_OFF) |
+ PHY_M_LED_MO_100(MO_LED_OFF) |
+ PHY_M_LED_MO_1000(MO_LED_OFF) |
+ PHY_M_LED_MO_RX(MO_LED_OFF));
+ }
+}
+
+static void skge_blink_timer(unsigned long data)
+{
+ struct skge_port *skge = (struct skge_port *) data;
+ struct skge_hw *hw = skge->hw;
+ unsigned long flags;
+
+ spin_lock_irqsave(&hw->phy_lock, flags);
+ if (skge->blink_on)
+ skge_led_on(hw, skge->port);
+ else
+ skge_led_off(hw, skge->port);
+ spin_unlock_irqrestore(&hw->phy_lock, flags);
+
+ skge->blink_on = !skge->blink_on;
+ mod_timer(&skge->led_blink, jiffies + BLINK_HZ);
+}
+
+/* blink LED's for finding board */
+static int skge_phys_id(struct net_device *dev, u32 data)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ if(!data || data > (u32)(MAX_SCHEDULE_TIMEOUT / HZ))
+ data = (u32)(MAX_SCHEDULE_TIMEOUT / HZ);
+
+ /* start blinking */
+ skge->blink_on = 1;
+ mod_timer(&skge->led_blink, jiffies+1);
+
+ msleep_interruptible(data * 1000);
+ del_timer_sync(&skge->led_blink);
+
+ skge_led_off(skge->hw, skge->port);
+
+ return 0;
+}
+
+static struct ethtool_ops skge_ethtool_ops = {
+ .get_settings = skge_get_settings,
+ .set_settings = skge_set_settings,
+ .get_drvinfo = skge_get_drvinfo,
+ .get_regs_len = skge_get_regs_len,
+ .get_regs = skge_get_regs,
+ .get_wol = skge_get_wol,
+ .set_wol = skge_set_wol,
+ .get_msglevel = skge_get_msglevel,
+ .set_msglevel = skge_set_msglevel,
+ .nway_reset = skge_nway_reset,
+ .get_link = ethtool_op_get_link,
+ .get_ringparam = skge_get_ring_param,
+ .set_ringparam = skge_set_ring_param,
+ .get_pauseparam = skge_get_pauseparam,
+ .set_pauseparam = skge_set_pauseparam,
+ .get_coalesce = skge_get_coalesce,
+ .set_coalesce = skge_set_coalesce,
+ .get_tso = ethtool_op_get_tso,
+ .set_tso = skge_set_tso,
+ .get_sg = ethtool_op_get_sg,
+ .set_sg = skge_set_sg,
+ .get_tx_csum = ethtool_op_get_tx_csum,
+ .set_tx_csum = skge_set_tx_csum,
+ .get_rx_csum = skge_get_rx_csum,
+ .set_rx_csum = skge_set_rx_csum,
+ .get_strings = skge_get_strings,
+ .phys_id = skge_phys_id,
+ .get_stats_count = skge_get_stats_count,
+ .get_ethtool_stats = skge_get_ethtool_stats,
+};
+
+/*
+ * Allocate ring elements and chain them together
+ * One-to-one association of board descriptors with ring elements
+ */
+static int skge_ring_alloc(struct skge_ring *ring, void *vaddr, u64 base)
+{
+ struct skge_tx_desc *d;
+ struct skge_element *e;
+ int i;
+
+ ring->start = kmalloc(sizeof(*e)*ring->count, GFP_KERNEL);
+ if (!ring->start)
+ return -ENOMEM;
+
+ for (i = 0, e = ring->start, d = vaddr; i < ring->count; i++, e++, d++) {
+ e->desc = d;
+ if (i == ring->count - 1) {
+ e->next = ring->start;
+ d->next_offset = base;
+ } else {
+ e->next = e + 1;
+ d->next_offset = base + (i+1) * sizeof(*d);
+ }
+ }
+ ring->to_use = ring->to_clean = ring->start;
+
+ return 0;
+}
+
+/* Setup buffer for receiving */
+static inline int skge_rx_alloc(struct skge_port *skge,
+ struct skge_element *e)
+{
+ unsigned long bufsize = skge->netdev->mtu + ETH_HLEN; /* VLAN? */
+ struct skge_rx_desc *rd = e->desc;
+ struct sk_buff *skb;
+ u64 map;
+
+ skb = dev_alloc_skb(bufsize + NET_IP_ALIGN);
+ if (unlikely(!skb)) {
+ printk(KERN_DEBUG PFX "%s: out of memory for receive\n",
+ skge->netdev->name);
+ return -ENOMEM;
+ }
+
+ skb->dev = skge->netdev;
+ skb_reserve(skb, NET_IP_ALIGN);
+
+ map = pci_map_single(skge->hw->pdev, skb->data, bufsize,
+ PCI_DMA_FROMDEVICE);
+
+ rd->dma_lo = map;
+ rd->dma_hi = map >> 32;
+ e->skb = skb;
+ rd->csum1_start = ETH_HLEN;
+ rd->csum2_start = ETH_HLEN;
+ rd->csum1 = 0;
+ rd->csum2 = 0;
+
+ wmb();
+
+ rd->control = BMU_OWN | BMU_STF | BMU_IRQ_EOF | BMU_TCP_CHECK | bufsize;
+ pci_unmap_addr_set(e, mapaddr, map);
+ pci_unmap_len_set(e, maplen, bufsize);
+ return 0;
+}
+
+/* Free all unused buffers in receive ring, assumes receiver stopped */
+static void skge_rx_clean(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ struct skge_ring *ring = &skge->rx_ring;
+ struct skge_element *e;
+
+ for (e = ring->to_clean; e != ring->to_use; e = e->next) {
+ struct skge_rx_desc *rd = e->desc;
+ rd->control = 0;
+
+ pci_unmap_single(hw->pdev,
+ pci_unmap_addr(e, mapaddr),
+ pci_unmap_len(e, maplen),
+ PCI_DMA_FROMDEVICE);
+ dev_kfree_skb(e->skb);
+ e->skb = NULL;
+ }
+ ring->to_clean = e;
+}
+
+/* Allocate buffers for receive ring
+ * For receive: to_use is refill location
+ * to_clean is next received frame.
+ *
+ * if (to_use == to_clean)
+ * then ring all frames in ring need buffers
+ * if (to_use->next == to_clean)
+ * then ring all frames in ring have buffers
+ */
+static int skge_rx_fill(struct skge_port *skge)
+{
+ struct skge_ring *ring = &skge->rx_ring;
+ struct skge_element *e;
+ int ret = 0;
+
+ for (e = ring->to_use; e->next != ring->to_clean; e = e->next) {
+ if (skge_rx_alloc(skge, e)) {
+ ret = 1;
+ break;
+ }
+
+ }
+ ring->to_use = e;
+
+ return ret;
+}
+
+static void skge_link_up(struct skge_port *skge)
+{
+ netif_carrier_on(skge->netdev);
+ if (skge->tx_avail > MAX_SKB_FRAGS + 1)
+ netif_wake_queue(skge->netdev);
+
+ if (netif_msg_link(skge))
+ printk(KERN_INFO PFX
+ "%s: Link is up at %d Mbps, %s duplex, flow control %s\n",
+ skge->netdev->name, skge->speed,
+ skge->duplex == DUPLEX_FULL ? "full" : "half",
+ (skge->flow_control == FLOW_MODE_NONE) ? "none" :
+ (skge->flow_control == FLOW_MODE_LOC_SEND) ? "tx only" :
+ (skge->flow_control == FLOW_MODE_REM_SEND) ? "rx only" :
+ (skge->flow_control == FLOW_MODE_SYMMETRIC) ? "tx and rx" :
+ "unknown");
+}
+
+static void skge_link_down(struct skge_port *skge)
+{
+ netif_carrier_off(skge->netdev);
+ netif_stop_queue(skge->netdev);
+
+ if (netif_msg_link(skge))
+ printk(KERN_INFO PFX "%s: Link is down.\n", skge->netdev->name);
+}
+
+static u16 skge_xm_phy_read(struct skge_hw *hw, int port, u16 reg)
+{
+ int i;
+ u16 v;
+
+ skge_xm_write16(hw, port, XM_PHY_ADDR, reg | hw->phy_addr);
+ v = skge_xm_read16(hw, port, XM_PHY_DATA);
+ if (hw->phy_type != SK_PHY_XMAC) {
+ for (i = 0; i < PHY_RETRIES; i++) {
+ udelay(1);
+ if (skge_xm_read16(hw, port, XM_MMU_CMD)
+ & XM_MMU_PHY_RDY)
+ goto ready;
+ }
+
+ printk(KERN_WARNING PFX "%s: phy read timed out\n",
+ hw->dev[port]->name);
+ return 0;
+ ready:
+ v = skge_xm_read16(hw, port, XM_PHY_DATA);
+ }
+
+ return v;
+}
+
+static void skge_xm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val)
+{
+ int i;
+
+ skge_xm_write16(hw, port, XM_PHY_ADDR, reg | hw->phy_addr);
+ for (i = 0; i < PHY_RETRIES; i++) {
+ if (!(skge_xm_read16(hw, port, XM_MMU_CMD) & XM_MMU_PHY_BUSY))
+ goto ready;
+ cpu_relax();
+ }
+ printk(KERN_WARNING PFX "%s: phy write failed to come ready\n",
+ hw->dev[port]->name);
+
+
+ ready:
+ skge_xm_write16(hw, port, XM_PHY_DATA, val);
+ for (i = 0; i < PHY_RETRIES; i++) {
+ udelay(1);
+ if (!(skge_xm_read16(hw, port, XM_MMU_CMD) & XM_MMU_PHY_BUSY))
+ return;
+ }
+ printk(KERN_WARNING PFX "%s: phy write timed out\n",
+ hw->dev[port]->name);
+}
+
+static void genesis_init(struct skge_hw *hw)
+{
+ /* set blink source counter */
+ skge_write32(hw, B2_BSC_INI, (SK_BLK_DUR * SK_FACT_53) / 100);
+ skge_write8(hw, B2_BSC_CTRL, BSC_START);
+
+ /* configure mac arbiter */
+ skge_write16(hw, B3_MA_TO_CTRL, MA_RST_CLR);
+
+ /* configure mac arbiter timeout values */
+ skge_write8(hw, B3_MA_TOINI_RX1, SK_MAC_TO_53);
+ skge_write8(hw, B3_MA_TOINI_RX2, SK_MAC_TO_53);
+ skge_write8(hw, B3_MA_TOINI_TX1, SK_MAC_TO_53);
+ skge_write8(hw, B3_MA_TOINI_TX2, SK_MAC_TO_53);
+
+ skge_write8(hw, B3_MA_RCINI_RX1, 0);
+ skge_write8(hw, B3_MA_RCINI_RX2, 0);
+ skge_write8(hw, B3_MA_RCINI_TX1, 0);
+ skge_write8(hw, B3_MA_RCINI_TX2, 0);
+
+ /* configure packet arbiter timeout */
+ skge_write16(hw, B3_PA_CTRL, PA_RST_CLR);
+ skge_write16(hw, B3_PA_TOINI_RX1, SK_PKT_TO_MAX);
+ skge_write16(hw, B3_PA_TOINI_TX1, SK_PKT_TO_MAX);
+ skge_write16(hw, B3_PA_TOINI_RX2, SK_PKT_TO_MAX);
+ skge_write16(hw, B3_PA_TOINI_TX2, SK_PKT_TO_MAX);
+}
+
+static void genesis_reset(struct skge_hw *hw, int port)
+{
+ int i;
+ u64 zero = 0;
+
+ /* reset the statistics module */
+ skge_xm_write32(hw, port, XM_GP_PORT, XM_GP_RES_STAT);
+ skge_xm_write16(hw, port, XM_IMSK, 0xffff); /* disable XMAC IRQs */
+ skge_xm_write32(hw, port, XM_MODE, 0); /* clear Mode Reg */
+ skge_xm_write16(hw, port, XM_TX_CMD, 0); /* reset TX CMD Reg */
+ skge_xm_write16(hw, port, XM_RX_CMD, 0); /* reset RX CMD Reg */
+
+ /* disable all PHY IRQs */
+ if (hw->phy_type == SK_PHY_BCOM)
+ skge_xm_write16(hw, port, PHY_BCOM_INT_MASK, 0xffff);
+
+ skge_xm_outhash(hw, port, XM_HSM, (u8 *) &zero);
+ for (i = 0; i < 15; i++)
+ skge_xm_outaddr(hw, port, XM_EXM(i), (u8 *) &zero);
+ skge_xm_outhash(hw, port, XM_SRC_CHK, (u8 *) &zero);
+}
+
+
+static void genesis_mac_init(struct skge_hw *hw, int port)
+{
+ struct skge_port *skge = netdev_priv(hw->dev[port]);
+ int i;
+ u32 r;
+ u16 id1;
+ u16 ctrl1, ctrl2, ctrl3, ctrl4, ctrl5;
+
+ /* magic workaround patterns for Broadcom */
+ static const struct {
+ u16 reg;
+ u16 val;
+ } A1hack[] = {
+ { 0x18, 0x0c20 }, { 0x17, 0x0012 }, { 0x15, 0x1104 },
+ { 0x17, 0x0013 }, { 0x15, 0x0404 }, { 0x17, 0x8006 },
+ { 0x15, 0x0132 }, { 0x17, 0x8006 }, { 0x15, 0x0232 },
+ { 0x17, 0x800D }, { 0x15, 0x000F }, { 0x18, 0x0420 },
+ }, C0hack[] = {
+ { 0x18, 0x0c20 }, { 0x17, 0x0012 }, { 0x15, 0x1204 },
+ { 0x17, 0x0013 }, { 0x15, 0x0A04 }, { 0x18, 0x0420 },
+ };
+
+
+ /* initialize Rx, Tx and Link LED */
+ skge_write8(hw, SKGEMAC_REG(port, LNK_LED_REG), LINKLED_ON);
+ skge_write8(hw, SKGEMAC_REG(port, LNK_LED_REG), LINKLED_LINKSYNC_ON);
+
+ skge_write8(hw, SKGEMAC_REG(port, RX_LED_CTRL), LED_START);
+ skge_write8(hw, SKGEMAC_REG(port, TX_LED_CTRL), LED_START);
+
+ /* Unreset the XMAC. */
+ skge_write16(hw, SKGEMAC_REG(port, TX_MFF_CTRL1), MFF_CLR_MAC_RST);
+
+ /*
+ * Perform additional initialization for external PHYs,
+ * namely for the 1000baseTX cards that use the XMAC's
+ * GMII mode.
+ */
+ spin_lock_bh(&hw->phy_lock);
+ if (hw->phy_type != SK_PHY_XMAC) {
+ /* Take PHY out of reset. */
+ r = skge_read32(hw, B2_GP_IO);
+ if (port == 0)
+ r |= GP_DIR_0|GP_IO_0;
+ else
+ r |= GP_DIR_2|GP_IO_2;
+
+ skge_write32(hw, B2_GP_IO, r);
+ skge_read32(hw, B2_GP_IO);
+
+ /* Enable GMII mode on the XMAC. */
+ skge_xm_write16(hw, port, XM_HW_CFG, XM_HW_GMII_MD);
+
+ id1 = skge_xm_phy_read(hw, port, PHY_XMAC_ID1);
+
+ /* Optimize MDIO transfer by suppressing preamble. */
+ skge_xm_write16(hw, port, XM_MMU_CMD,
+ skge_xm_read16(hw, port, XM_MMU_CMD)
+ | XM_MMU_NO_PRE);
+
+ if (id1 == PHY_BCOM_ID1_C0) {
+ /*
+ * Workaround BCOM Errata for the C0 type.
+ * Write magic patterns to reserved registers.
+ */
+ for (i = 0; i < ARRAY_SIZE(C0hack); i++)
+ skge_xm_phy_write(hw, port,
+ C0hack[i].reg, C0hack[i].val);
+
+ } else if (id1 == PHY_BCOM_ID1_A1) {
+ /*
+ * Workaround BCOM Errata for the A1 type.
+ * Write magic patterns to reserved registers.
+ */
+ for (i = 0; i < ARRAY_SIZE(A1hack); i++)
+ skge_xm_phy_write(hw, port,
+ A1hack[i].reg, A1hack[i].val);
+ }
+
+ /*
+ * Workaround BCOM Errata (#10523) for all BCom PHYs.
+ * Disable Power Management after reset.
+ */
+ r = skge_xm_phy_read(hw, port, PHY_BCOM_AUX_CTRL);
+ skge_xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL, r | PHY_B_AC_DIS_PM);
+ }
+
+ /* Dummy read */
+ skge_xm_read16(hw, port, XM_ISRC);
+
+ r = skge_xm_read32(hw, port, XM_MODE);
+ skge_xm_write32(hw, port, XM_MODE, r|XM_MD_CSA);
+
+ /* We don't need the FCS appended to the packet. */
+ r = skge_xm_read16(hw, port, XM_RX_CMD);
+ skge_xm_write16(hw, port, XM_RX_CMD, r | XM_RX_STRIP_FCS);
+
+ /* We want short frames padded to 60 bytes. */
+ r = skge_xm_read16(hw, port, XM_TX_CMD);
+ skge_xm_write16(hw, port, XM_TX_CMD, r | XM_TX_AUTO_PAD);
+
+ /*
+ * Enable the reception of all error frames. This is is
+ * a necessary evil due to the design of the XMAC. The
+ * XMAC's receive FIFO is only 8K in size, however jumbo
+ * frames can be up to 9000 bytes in length. When bad
+ * frame filtering is enabled, the XMAC's RX FIFO operates
+ * in 'store and forward' mode. For this to work, the
+ * entire frame has to fit into the FIFO, but that means
+ * that jumbo frames larger than 8192 bytes will be
+ * truncated. Disabling all bad frame filtering causes
+ * the RX FIFO to operate in streaming mode, in which
+ * case the XMAC will start transfering frames out of the
+ * RX FIFO as soon as the FIFO threshold is reached.
+ */
+ r = skge_xm_read32(hw, port, XM_MODE);
+ skge_xm_write32(hw, port, XM_MODE,
+ XM_MD_RX_CRCE|XM_MD_RX_LONG|XM_MD_RX_RUNT|
+ XM_MD_RX_ERR|XM_MD_RX_IRLE);
+
+ skge_xm_outaddr(hw, port, XM_SA, hw->dev[port]->dev_addr);
+ skge_xm_outaddr(hw, port, XM_EXM(0), hw->dev[port]->dev_addr);
+
+ /*
+ * Bump up the transmit threshold. This helps hold off transmit
+ * underruns when we're blasting traffic from both ports at once.
+ */
+ skge_xm_write16(hw, port, XM_TX_THR, 512);
+
+ /* Configure MAC arbiter */
+ skge_write16(hw, B3_MA_TO_CTRL, MA_RST_CLR);
+
+ /* configure timeout values */
+ skge_write8(hw, B3_MA_TOINI_RX1, 72);
+ skge_write8(hw, B3_MA_TOINI_RX2, 72);
+ skge_write8(hw, B3_MA_TOINI_TX1, 72);
+ skge_write8(hw, B3_MA_TOINI_TX2, 72);
+
+ skge_write8(hw, B3_MA_RCINI_RX1, 0);
+ skge_write8(hw, B3_MA_RCINI_RX2, 0);
+ skge_write8(hw, B3_MA_RCINI_TX1, 0);
+ skge_write8(hw, B3_MA_RCINI_TX2, 0);
+
+ /* Configure Rx MAC FIFO */
+ skge_write8(hw, SKGEMAC_REG(port, RX_MFF_CTRL2), MFF_RST_CLR);
+ skge_write16(hw, SKGEMAC_REG(port, RX_MFF_CTRL1), MFF_ENA_TIM_PAT);
+ skge_write8(hw, SKGEMAC_REG(port, RX_MFF_CTRL2), MFF_ENA_OP_MD);
+
+ /* Configure Tx MAC FIFO */
+ skge_write8(hw, SKGEMAC_REG(port, TX_MFF_CTRL2), MFF_RST_CLR);
+ skge_write16(hw, SKGEMAC_REG(port, TX_MFF_CTRL1), MFF_TX_CTRL_DEF);
+ skge_write8(hw, SKGEMAC_REG(port, TX_MFF_CTRL2), MFF_ENA_OP_MD);
+
+ if (hw->dev[port]->mtu > ETH_DATA_LEN) {
+ /* Enable frame flushing if jumbo frames used */
+ skge_write16(hw, SKGEMAC_REG(port,RX_MFF_CTRL1), MFF_ENA_FLUSH);
+ } else {
+ /* enable timeout timers if normal frames */
+ skge_write16(hw, B3_PA_CTRL,
+ port == 0 ? PA_ENA_TO_TX1 : PA_ENA_TO_TX2);
+ }
+
+
+ r = skge_xm_read16(hw, port, XM_RX_CMD);
+ if (hw->dev[port]->mtu > ETH_DATA_LEN)
+ skge_xm_write16(hw, port, XM_RX_CMD, r | XM_RX_BIG_PK_OK);
+ else
+ skge_xm_write16(hw, port, XM_RX_CMD, r & ~(XM_RX_BIG_PK_OK));
+
+ switch (hw->phy_type) {
+ case SK_PHY_XMAC:
+ if (skge->autoneg == AUTONEG_ENABLE) {
+ ctrl1 = PHY_X_AN_FD | PHY_X_AN_HD;
+
+ switch (skge->flow_control) {
+ case FLOW_MODE_NONE:
+ ctrl1 |= PHY_X_P_NO_PAUSE;
+ break;
+ case FLOW_MODE_LOC_SEND:
+ ctrl1 |= PHY_X_P_ASYM_MD;
+ break;
+ case FLOW_MODE_SYMMETRIC:
+ ctrl1 |= PHY_X_P_SYM_MD;
+ break;
+ case FLOW_MODE_REM_SEND:
+ ctrl1 |= PHY_X_P_BOTH_MD;
+ break;
+ }
+
+ skge_xm_phy_write(hw, port, PHY_XMAC_AUNE_ADV, ctrl1);
+ ctrl2 = PHY_CT_ANE | PHY_CT_RE_CFG;
+ } else {
+ ctrl2 = 0;
+ if (skge->duplex == DUPLEX_FULL)
+ ctrl2 |= PHY_CT_DUP_MD;
+ }
+
+ skge_xm_phy_write(hw, port, PHY_XMAC_CTRL, ctrl2);
+ break;
+
+ case SK_PHY_BCOM:
+ ctrl1 = PHY_CT_SP1000;
+ ctrl2 = 0;
+ ctrl3 = PHY_SEL_TYPE;
+ ctrl4 = PHY_B_PEC_EN_LTR;
+ ctrl5 = PHY_B_AC_TX_TST;
+
+ if (skge->autoneg == AUTONEG_ENABLE) {
+ /*
+ * Workaround BCOM Errata #1 for the C5 type.
+ * 1000Base-T Link Acquisition Failure in Slave Mode
+ * Set Repeater/DTE bit 10 of the 1000Base-T Control Register
+ */
+ ctrl2 |= PHY_B_1000C_RD;
+ if (skge->advertising & ADVERTISED_1000baseT_Half)
+ ctrl2 |= PHY_B_1000C_AHD;
+ if (skge->advertising & ADVERTISED_1000baseT_Full)
+ ctrl2 |= PHY_B_1000C_AFD;
+
+ /* Set Flow-control capabilities */
+ switch (skge->flow_control) {
+ case FLOW_MODE_NONE:
+ ctrl3 |= PHY_B_P_NO_PAUSE;
+ break;
+ case FLOW_MODE_LOC_SEND:
+ ctrl3 |= PHY_B_P_ASYM_MD;
+ break;
+ case FLOW_MODE_SYMMETRIC:
+ ctrl3 |= PHY_B_P_SYM_MD;
+ break;
+ case FLOW_MODE_REM_SEND:
+ ctrl3 |= PHY_B_P_BOTH_MD;
+ break;
+ }
+
+ /* Restart Auto-negotiation */
+ ctrl1 |= PHY_CT_ANE | PHY_CT_RE_CFG;
+ } else {
+ if (skge->duplex == DUPLEX_FULL)
+ ctrl1 |= PHY_CT_DUP_MD;
+
+ ctrl2 |= PHY_B_1000C_MSE; /* set it to Slave */
+ }
+
+ skge_xm_phy_write(hw, port, PHY_BCOM_1000T_CTRL, ctrl2);
+ skge_xm_phy_write(hw, port, PHY_BCOM_AUNE_ADV, ctrl3);
+
+ if (skge->netdev->mtu > ETH_DATA_LEN) {
+ ctrl4 |= PHY_B_PEC_HIGH_LA;
+ ctrl5 |= PHY_B_AC_LONG_PACK;
+
+ skge_xm_phy_write(hw, port,PHY_BCOM_AUX_CTRL, ctrl5);
+ }
+
+ skge_xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, ctrl4);
+ skge_xm_phy_write(hw, port, PHY_BCOM_CTRL, ctrl1);
+ break;
+ }
+ spin_unlock_bh(&hw->phy_lock);
+
+ /* Clear MIB counters */
+ skge_xm_write16(hw, port, XM_STAT_CMD,
+ XM_SC_CLR_RXC | XM_SC_CLR_TXC);
+ /* Clear two times according to Errata #3 */
+ skge_xm_write16(hw, port, XM_STAT_CMD,
+ XM_SC_CLR_RXC | XM_SC_CLR_TXC);
+
+ /* Start polling for link status */
+ mod_timer(&skge->link_check, jiffies + LINK_POLL_HZ);
+}
+
+static void genesis_stop(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+
+ /* Clear Tx packet arbiter timeout IRQ */
+ skge_write16(hw, B3_PA_CTRL,
+ port == 0 ? PA_CLR_TO_TX1 : PA_CLR_TO_TX2);
+
+ /*
+ * If the transfer stucks at the MAC the STOP command will not
+ * terminate if we don't flush the XMAC's transmit FIFO !
+ */
+ skge_xm_write32(hw, port, XM_MODE,
+ skge_xm_read32(hw, port, XM_MODE)|XM_MD_FTF);
+
+
+ /* Reset the MAC */
+ skge_write16(hw, SKGEMAC_REG(port, TX_MFF_CTRL1), MFF_SET_MAC_RST);
+
+ /* For external PHYs there must be special handling */
+ if (hw->phy_type != SK_PHY_XMAC) {
+ u32 reg = skge_read32(hw, B2_GP_IO);
+
+ if (port == 0) {
+ reg |= GP_DIR_0;
+ reg &= ~GP_IO_0;
+ } else {
+ reg |= GP_DIR_2;
+ reg &= ~GP_IO_2;
+ }
+ skge_write32(hw, B2_GP_IO, reg);
+ skge_read32(hw, B2_GP_IO);
+ }
+
+ skge_xm_write16(hw, port, XM_MMU_CMD,
+ skge_xm_read16(hw, port, XM_MMU_CMD)
+ & ~(XM_MMU_ENA_RX | XM_MMU_ENA_TX));
+
+ skge_xm_read16(hw, port, XM_MMU_CMD);
+}
+
+
+static void genesis_get_stats(struct skge_port *skge, u64 *data)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ int i;
+ unsigned long timeout = jiffies + HZ;
+
+ skge_xm_write16(hw, port,
+ XM_STAT_CMD, XM_SC_SNP_TXC | XM_SC_SNP_RXC);
+
+ /* wait for update to complete */
+ while (skge_xm_read16(hw, port, XM_STAT_CMD)
+ & (XM_SC_SNP_TXC | XM_SC_SNP_RXC)) {
+ if (time_after(jiffies, timeout))
+ break;
+ udelay(10);
+ }
+
+ /* special case for 64 bit octet counter */
+ data[0] = (u64) skge_xm_read32(hw, port, XM_TXO_OK_HI) << 32
+ | skge_xm_read32(hw, port, XM_TXO_OK_LO);
+ data[1] = (u64) skge_xm_read32(hw, port, XM_RXO_OK_HI) << 32
+ | skge_xm_read32(hw, port, XM_RXO_OK_LO);
+
+ for (i = 2; i < ARRAY_SIZE(skge_stats); i++)
+ data[i] = skge_xm_read32(hw, port, skge_stats[i].xmac_offset);
+}
+
+static void genesis_mac_intr(struct skge_hw *hw, int port)
+{
+ struct skge_port *skge = netdev_priv(hw->dev[port]);
+ u16 status = skge_xm_read16(hw, port, XM_ISRC);
+
+ pr_debug("genesis_intr status %x\n", status);
+ if (hw->phy_type == SK_PHY_XMAC) {
+ /* LInk down, start polling for state change */
+ if (status & XM_IS_INP_ASS) {
+ skge_xm_write16(hw, port, XM_IMSK,
+ skge_xm_read16(hw, port, XM_IMSK) | XM_IS_INP_ASS);
+ mod_timer(&skge->link_check, jiffies + LINK_POLL_HZ);
+ }
+ else if (status & XM_IS_AND)
+ mod_timer(&skge->link_check, jiffies + LINK_POLL_HZ);
+ }
+
+ if (status & XM_IS_TXF_UR) {
+ skge_xm_write32(hw, port, XM_MODE, XM_MD_FTF);
+ ++skge->net_stats.tx_fifo_errors;
+ }
+ if (status & XM_IS_RXF_OV) {
+ skge_xm_write32(hw, port, XM_MODE, XM_MD_FRF);
+ ++skge->net_stats.rx_fifo_errors;
+ }
+}
+
+static void skge_gm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val)
+{
+ int i;
+
+ skge_gma_write16(hw, port, GM_SMI_DATA, val);
+ skge_gma_write16(hw, port, GM_SMI_CTRL,
+ GM_SMI_CT_PHY_AD(hw->phy_addr) | GM_SMI_CT_REG_AD(reg));
+ for (i = 0; i < PHY_RETRIES; i++) {
+ udelay(1);
+
+ if (!(skge_gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_BUSY))
+ break;
+ }
+}
+
+static u16 skge_gm_phy_read(struct skge_hw *hw, int port, u16 reg)
+{
+ int i;
+
+ skge_gma_write16(hw, port, GM_SMI_CTRL,
+ GM_SMI_CT_PHY_AD(hw->phy_addr)
+ | GM_SMI_CT_REG_AD(reg) | GM_SMI_CT_OP_RD);
+
+ for (i = 0; i < PHY_RETRIES; i++) {
+ udelay(1);
+ if (skge_gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_RD_VAL)
+ goto ready;
+ }
+
+ printk(KERN_WARNING PFX "%s: phy read timeout\n",
+ hw->dev[port]->name);
+ return 0;
+ ready:
+ return skge_gma_read16(hw, port, GM_SMI_DATA);
+}
+
+static void genesis_link_down(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+
+ pr_debug("genesis_link_down\n");
+
+ skge_xm_write16(hw, port, XM_MMU_CMD,
+ skge_xm_read16(hw, port, XM_MMU_CMD)
+ & ~(XM_MMU_ENA_RX | XM_MMU_ENA_TX));
+
+ /* dummy read to ensure writing */
+ (void) skge_xm_read16(hw, port, XM_MMU_CMD);
+
+ skge_link_down(skge);
+}
+
+static void genesis_link_up(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u16 cmd;
+ u32 mode, msk;
+
+ pr_debug("genesis_link_up\n");
+ cmd = skge_xm_read16(hw, port, XM_MMU_CMD);
+
+ /*
+ * enabling pause frame reception is required for 1000BT
+ * because the XMAC is not reset if the link is going down
+ */
+ if (skge->flow_control == FLOW_MODE_NONE ||
+ skge->flow_control == FLOW_MODE_LOC_SEND)
+ cmd |= XM_MMU_IGN_PF;
+ else
+ /* Enable Pause Frame Reception */
+ cmd &= ~XM_MMU_IGN_PF;
+
+ skge_xm_write16(hw, port, XM_MMU_CMD, cmd);
+
+ mode = skge_xm_read32(hw, port, XM_MODE);
+ if (skge->flow_control == FLOW_MODE_SYMMETRIC ||
+ skge->flow_control == FLOW_MODE_LOC_SEND) {
+ /*
+ * Configure Pause Frame Generation
+ * Use internal and external Pause Frame Generation.
+ * Sending pause frames is edge triggered.
+ * Send a Pause frame with the maximum pause time if
+ * internal oder external FIFO full condition occurs.
+ * Send a zero pause time frame to re-start transmission.
+ */
+ /* XM_PAUSE_DA = '010000C28001' (default) */
+ /* XM_MAC_PTIME = 0xffff (maximum) */
+ /* remember this value is defined in big endian (!) */
+ skge_xm_write16(hw, port, XM_MAC_PTIME, 0xffff);
+
+ mode |= XM_PAUSE_MODE;
+ skge_write16(hw, SKGEMAC_REG(port, RX_MFF_CTRL1), MFF_ENA_PAUSE);
+ } else {
+ /*
+ * disable pause frame generation is required for 1000BT
+ * because the XMAC is not reset if the link is going down
+ */
+ /* Disable Pause Mode in Mode Register */
+ mode &= ~XM_PAUSE_MODE;
+
+ skge_write16(hw, SKGEMAC_REG(port, RX_MFF_CTRL1), MFF_DIS_PAUSE);
+ }
+
+ skge_xm_write32(hw, port, XM_MODE, mode);
+
+ msk = XM_DEF_MSK;
+ if (hw->phy_type != SK_PHY_XMAC)
+ msk |= XM_IS_INP_ASS; /* disable GP0 interrupt bit */
+
+ skge_xm_write16(hw, port, XM_IMSK, msk);
+ skge_xm_read16(hw, port, XM_ISRC);
+
+ /* get MMU Command Reg. */
+ cmd = skge_xm_read16(hw, port, XM_MMU_CMD);
+ if (hw->phy_type != SK_PHY_XMAC && skge->duplex == DUPLEX_FULL)
+ cmd |= XM_MMU_GMII_FD;
+
+ if (hw->phy_type == SK_PHY_BCOM) {
+ /*
+ * Workaround BCOM Errata (#10523) for all BCom Phys
+ * Enable Power Management after link up
+ */
+ skge_xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL,
+ skge_xm_phy_read(hw, port, PHY_BCOM_AUX_CTRL)
+ & ~PHY_B_AC_DIS_PM);
+ skge_xm_phy_write(hw, port, PHY_BCOM_INT_MASK,
+ PHY_B_DEF_MSK);
+ }
+
+ /* enable Rx/Tx */
+ skge_xm_write16(hw, port, XM_MMU_CMD,
+ cmd | XM_MMU_ENA_RX | XM_MMU_ENA_TX);
+ skge_link_up(skge);
+}
+
+
+static void genesis_bcom_intr(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u16 stat = skge_xm_phy_read(hw, port, PHY_BCOM_INT_STAT);
+
+ pr_debug("genesis_bcom intr stat=%x\n", stat);
+
+ /* Workaround BCom Errata:
+ * enable and disable loopback mode if "NO HCD" occurs.
+ */
+ if (stat & PHY_B_IS_NO_HDCL) {
+ u16 ctrl = skge_xm_phy_read(hw, port, PHY_BCOM_CTRL);
+ skge_xm_phy_write(hw, port, PHY_BCOM_CTRL,
+ ctrl | PHY_CT_LOOP);
+ skge_xm_phy_write(hw, port, PHY_BCOM_CTRL,
+ ctrl & ~PHY_CT_LOOP);
+ }
+
+ stat = skge_xm_phy_read(hw, port, PHY_BCOM_STAT);
+ if (stat & (PHY_B_IS_AN_PR | PHY_B_IS_LST_CHANGE)) {
+ u16 aux = skge_xm_phy_read(hw, port, PHY_BCOM_AUX_STAT);
+ if ( !(aux & PHY_B_AS_LS) && netif_carrier_ok(skge->netdev))
+ genesis_link_down(skge);
+
+ else if (stat & PHY_B_IS_LST_CHANGE) {
+ if (aux & PHY_B_AS_AN_C) {
+ switch (aux & PHY_B_AS_AN_RES_MSK) {
+ case PHY_B_RES_1000FD:
+ skge->duplex = DUPLEX_FULL;
+ break;
+ case PHY_B_RES_1000HD:
+ skge->duplex = DUPLEX_HALF;
+ break;
+ }
+
+ switch (aux & PHY_B_AS_PAUSE_MSK) {
+ case PHY_B_AS_PAUSE_MSK:
+ skge->flow_control = FLOW_MODE_SYMMETRIC;
+ break;
+ case PHY_B_AS_PRR:
+ skge->flow_control = FLOW_MODE_REM_SEND;
+ break;
+ case PHY_B_AS_PRT:
+ skge->flow_control = FLOW_MODE_LOC_SEND;
+ break;
+ default:
+ skge->flow_control = FLOW_MODE_NONE;
+ }
+ skge->speed = SPEED_1000;
+ }
+ genesis_link_up(skge);
+ }
+ else
+ mod_timer(&skge->link_check, jiffies + LINK_POLL_HZ);
+ }
+}
+
+/* Perodic poll of phy status to check for link transistion */
+static void skge_link_timer(unsigned long __arg)
+{
+ struct skge_port *skge = (struct skge_port *) __arg;
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+
+ if (hw->chip_id != CHIP_ID_GENESIS || !netif_running(skge->netdev))
+ return;
+
+ spin_lock_bh(&hw->phy_lock);
+ if (hw->phy_type == SK_PHY_BCOM)
+ genesis_bcom_intr(skge);
+ else {
+ int i;
+ for (i = 0; i < 3; i++)
+ if (skge_xm_read16(hw, port, XM_ISRC) & XM_IS_INP_ASS)
+ break;
+
+ if (i == 3)
+ mod_timer(&skge->link_check, jiffies + LINK_POLL_HZ);
+ else
+ genesis_link_up(skge);
+ }
+ spin_unlock_bh(&hw->phy_lock);
+}
+
+/* Marvell Phy Initailization */
+static void yukon_init(struct skge_hw *hw, int port)
+{
+ struct skge_port *skge = netdev_priv(hw->dev[port]);
+ u16 ctrl, ct1000, adv;
+ u16 ledctrl, ledover;
+
+ pr_debug("yukon_init\n");
+ if (skge->autoneg == AUTONEG_ENABLE) {
+ u16 ectrl = skge_gm_phy_read(hw, port, PHY_MARV_EXT_CTRL);
+
+ ectrl &= ~(PHY_M_EC_M_DSC_MSK | PHY_M_EC_S_DSC_MSK |
+ PHY_M_EC_MAC_S_MSK);
+ ectrl |= PHY_M_EC_MAC_S(MAC_TX_CLK_25_MHZ);
+
+ /* on PHY 88E1111 there is a change for downshift control */
+ if (hw->chip_id == CHIP_ID_YUKON_EC)
+ ectrl |= PHY_M_EC_M_DSC_2(0) | PHY_M_EC_DOWN_S_ENA;
+ else
+ ectrl |= PHY_M_EC_M_DSC(0) | PHY_M_EC_S_DSC(1);
+
+ skge_gm_phy_write(hw, port, PHY_MARV_EXT_CTRL, ectrl);
+ }
+
+ ctrl = skge_gm_phy_read(hw, port, PHY_MARV_CTRL);
+ if (skge->autoneg == AUTONEG_DISABLE)
+ ctrl &= ~PHY_CT_ANE;
+
+ ctrl |= PHY_CT_RESET;
+ skge_gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
+
+ ctrl = 0;
+ ct1000 = 0;
+ adv = PHY_SEL_TYPE;
+
+ if (skge->autoneg == AUTONEG_ENABLE) {
+ if (iscopper(hw)) {
+ if (skge->advertising & ADVERTISED_1000baseT_Full)
+ ct1000 |= PHY_M_1000C_AFD;
+ if (skge->advertising & ADVERTISED_1000baseT_Half)
+ ct1000 |= PHY_M_1000C_AHD;
+ if (skge->advertising & ADVERTISED_100baseT_Full)
+ adv |= PHY_M_AN_100_FD;
+ if (skge->advertising & ADVERTISED_100baseT_Half)
+ adv |= PHY_M_AN_100_HD;
+ if (skge->advertising & ADVERTISED_10baseT_Full)
+ adv |= PHY_M_AN_10_FD;
+ if (skge->advertising & ADVERTISED_10baseT_Half)
+ adv |= PHY_M_AN_10_HD;
+
+ /* Set Flow-control capabilities */
+ switch (skge->flow_control) {
+ case FLOW_MODE_NONE:
+ adv |= PHY_B_P_NO_PAUSE;
+ break;
+ case FLOW_MODE_LOC_SEND:
+ adv |= PHY_B_P_ASYM_MD;
+ break;
+ case FLOW_MODE_SYMMETRIC:
+ adv |= PHY_B_P_SYM_MD;
+ break;
+ case FLOW_MODE_REM_SEND:
+ adv |= PHY_B_P_BOTH_MD;
+ break;
+ }
+ } else { /* special defines for FIBER (88E1011S only) */
+ adv |= PHY_M_AN_1000X_AHD | PHY_M_AN_1000X_AFD;
+
+ /* Set Flow-control capabilities */
+ switch (skge->flow_control) {
+ case FLOW_MODE_NONE:
+ adv |= PHY_M_P_NO_PAUSE_X;
+ break;
+ case FLOW_MODE_LOC_SEND:
+ adv |= PHY_M_P_ASYM_MD_X;
+ break;
+ case FLOW_MODE_SYMMETRIC:
+ adv |= PHY_M_P_SYM_MD_X;
+ break;
+ case FLOW_MODE_REM_SEND:
+ adv |= PHY_M_P_BOTH_MD_X;
+ break;
+ }
+ }
+ /* Restart Auto-negotiation */
+ ctrl |= PHY_CT_ANE | PHY_CT_RE_CFG;
+ } else {
+ /* forced speed/duplex settings */
+ ct1000 = PHY_M_1000C_MSE;
+
+ if (skge->duplex == DUPLEX_FULL)
+ ctrl |= PHY_CT_DUP_MD;
+
+ switch (skge->speed) {
+ case SPEED_1000:
+ ctrl |= PHY_CT_SP1000;
+ break;
+ case SPEED_100:
+ ctrl |= PHY_CT_SP100;
+ break;
+ }
+
+ ctrl |= PHY_CT_RESET;
+ }
+
+ if (hw->chip_id != CHIP_ID_YUKON_FE)
+ skge_gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, ct1000);
+
+ skge_gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, adv);
+ skge_gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
+
+ /* Setup Phy LED's */
+ ledctrl = PHY_M_LED_PULS_DUR(PULS_170MS);
+ ledover = 0;
+
+ if (hw->chip_id == CHIP_ID_YUKON_FE) {
+ /* on 88E3082 these bits are at 11..9 (shifted left) */
+ ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) << 1;
+
+ skge_gm_phy_write(hw, port, PHY_MARV_FE_LED_PAR,
+ ((skge_gm_phy_read(hw, port, PHY_MARV_FE_LED_PAR)
+
+ & ~PHY_M_FELP_LED1_MSK)
+ | PHY_M_FELP_LED1_CTRL(LED_PAR_CTRL_ACT_BL)));
+ } else {
+ /* set Tx LED (LED_TX) to blink mode on Rx OR Tx activity */
+ ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) | PHY_M_LEDC_TX_CTRL;
+
+ /* turn off the Rx LED (LED_RX) */
+ ledover |= PHY_M_LED_MO_RX(MO_LED_OFF);
+ }
+
+ /* disable blink mode (LED_DUPLEX) on collisions */
+ ctrl |= PHY_M_LEDC_DP_CTRL;
+ skge_gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
+
+ if (skge->autoneg == AUTONEG_DISABLE || skge->speed == SPEED_100) {
+ /* turn on 100 Mbps LED (LED_LINK100) */
+ ledover |= PHY_M_LED_MO_100(MO_LED_ON);
+ }
+
+ if (ledover)
+ skge_gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
+
+ /* Enable phy interrupt on autonegotiation complete (or link up) */
+ if (skge->autoneg == AUTONEG_ENABLE)
+ skge_gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_COMPL);
+ else
+ skge_gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
+}
+
+static void yukon_reset(struct skge_hw *hw, int port)
+{
+ skge_gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0);/* disable PHY IRQs */
+ skge_gma_write16(hw, port, GM_MC_ADDR_H1, 0); /* clear MC hash */
+ skge_gma_write16(hw, port, GM_MC_ADDR_H2, 0);
+ skge_gma_write16(hw, port, GM_MC_ADDR_H3, 0);
+ skge_gma_write16(hw, port, GM_MC_ADDR_H4, 0);
+
+ skge_gma_write16(hw, port, GM_RX_CTRL,
+ skge_gma_read16(hw, port, GM_RX_CTRL)
+ | GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA);
+}
+
+static void yukon_mac_init(struct skge_hw *hw, int port)
+{
+ struct skge_port *skge = netdev_priv(hw->dev[port]);
+ int i;
+ u32 reg;
+ const u8 *addr = hw->dev[port]->dev_addr;
+
+ /* WA code for COMA mode -- set PHY reset */
+ if (hw->chip_id == CHIP_ID_YUKON_LITE &&
+ chip_rev(hw) == CHIP_REV_YU_LITE_A3)
+ skge_write32(hw, B2_GP_IO,
+ (skge_read32(hw, B2_GP_IO) | GP_DIR_9 | GP_IO_9));
+
+ /* hard reset */
+ skge_write32(hw, SKGEMAC_REG(port, GPHY_CTRL), GPC_RST_SET);
+ skge_write32(hw, SKGEMAC_REG(port, GMAC_CTRL), GMC_RST_SET);
+
+ /* WA code for COMA mode -- clear PHY reset */
+ if (hw->chip_id == CHIP_ID_YUKON_LITE &&
+ chip_rev(hw) == CHIP_REV_YU_LITE_A3)
+ skge_write32(hw, B2_GP_IO,
+ (skge_read32(hw, B2_GP_IO) | GP_DIR_9)
+ & ~GP_IO_9);
+
+ /* Set hardware config mode */
+ reg = GPC_INT_POL_HI | GPC_DIS_FC | GPC_DIS_SLEEP |
+ GPC_ENA_XC | GPC_ANEG_ADV_ALL_M | GPC_ENA_PAUSE;
+ reg |= iscopper(hw) ? GPC_HWCFG_GMII_COP : GPC_HWCFG_GMII_FIB;
+
+ /* Clear GMC reset */
+ skge_write32(hw, SKGEMAC_REG(port, GPHY_CTRL), reg | GPC_RST_SET);
+ skge_write32(hw, SKGEMAC_REG(port, GPHY_CTRL), reg | GPC_RST_CLR);
+ skge_write32(hw, SKGEMAC_REG(port, GMAC_CTRL), GMC_PAUSE_ON | GMC_RST_CLR);
+ if (skge->autoneg == AUTONEG_DISABLE) {
+ reg = GM_GPCR_AU_ALL_DIS;
+ skge_gma_write16(hw, port, GM_GP_CTRL,
+ skge_gma_read16(hw, port, GM_GP_CTRL) | reg);
+
+ switch (skge->speed) {
+ case SPEED_1000:
+ reg |= GM_GPCR_SPEED_1000;
+ /* fallthru */
+ case SPEED_100:
+ reg |= GM_GPCR_SPEED_100;
+ }
+
+ if (skge->duplex == DUPLEX_FULL)
+ reg |= GM_GPCR_DUP_FULL;
+ } else
+ reg = GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100 | GM_GPCR_DUP_FULL;
+ switch (skge->flow_control) {
+ case FLOW_MODE_NONE:
+ skge_write32(hw, SKGEMAC_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
+ reg |= GM_GPCR_FC_TX_DIS | GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS;
+ break;
+ case FLOW_MODE_LOC_SEND:
+ /* disable Rx flow-control */
+ reg |= GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS;
+ }
+
+ skge_gma_write16(hw, port, GM_GP_CTRL, reg);
+ skge_read16(hw, GMAC_IRQ_SRC);
+
+ spin_lock_bh(&hw->phy_lock);
+ yukon_init(hw, port);
+ spin_unlock_bh(&hw->phy_lock);
+
+ /* MIB clear */
+ reg = skge_gma_read16(hw, port, GM_PHY_ADDR);
+ skge_gma_write16(hw, port, GM_PHY_ADDR, reg | GM_PAR_MIB_CLR);
+
+ for (i = 0; i < GM_MIB_CNT_SIZE; i++)
+ skge_gma_read16(hw, port, GM_MIB_CNT_BASE + 8*i);
+ skge_gma_write16(hw, port, GM_PHY_ADDR, reg);
+
+ /* transmit control */
+ skge_gma_write16(hw, port, GM_TX_CTRL, TX_COL_THR(TX_COL_DEF));
+
+ /* receive control reg: unicast + multicast + no FCS */
+ skge_gma_write16(hw, port, GM_RX_CTRL,
+ GM_RXCR_UCF_ENA | GM_RXCR_CRC_DIS | GM_RXCR_MCF_ENA);
+
+ /* transmit flow control */
+ skge_gma_write16(hw, port, GM_TX_FLOW_CTRL, 0xffff);
+
+ /* transmit parameter */
+ skge_gma_write16(hw, port, GM_TX_PARAM,
+ TX_JAM_LEN_VAL(TX_JAM_LEN_DEF) |
+ TX_JAM_IPG_VAL(TX_JAM_IPG_DEF) |
+ TX_IPG_JAM_DATA(TX_IPG_JAM_DEF));
+
+ /* serial mode register */
+ reg = GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF);
+ if (hw->dev[port]->mtu > 1500)
+ reg |= GM_SMOD_JUMBO_ENA;
+
+ skge_gma_write16(hw, port, GM_SERIAL_MODE, reg);
+
+ /* physical address: used for pause frames */
+ skge_gm_set_addr(hw, port, GM_SRC_ADDR_1L, addr);
+ /* virtual address for data */
+ skge_gm_set_addr(hw, port, GM_SRC_ADDR_2L, addr);
+
+ /* enable interrupt mask for counter overflows */
+ skge_gma_write16(hw, port, GM_TX_IRQ_MSK, 0);
+ skge_gma_write16(hw, port, GM_RX_IRQ_MSK, 0);
+ skge_gma_write16(hw, port, GM_TR_IRQ_MSK, 0);
+
+ /* Initialize Mac Fifo */
+
+ /* Configure Rx MAC FIFO */
+ skge_write16(hw, SKGEMAC_REG(port, RX_GMF_FL_MSK), RX_FF_FL_DEF_MSK);
+ reg = GMF_OPER_ON | GMF_RX_F_FL_ON;
+ if (hw->chip_id == CHIP_ID_YUKON_LITE &&
+ chip_rev(hw) == CHIP_REV_YU_LITE_A3)
+ reg &= ~GMF_RX_F_FL_ON;
+ skge_write8(hw, SKGEMAC_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR);
+ skge_write16(hw, SKGEMAC_REG(port, RX_GMF_CTRL_T), reg);
+ skge_write16(hw, SKGEMAC_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF);
+
+ /* Configure Tx MAC FIFO */
+ skge_write8(hw, SKGEMAC_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR);
+ skge_write16(hw, SKGEMAC_REG(port, TX_GMF_CTRL_T), GMF_OPER_ON);
+}
+
+static void yukon_stop(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+
+ if (hw->chip_id == CHIP_ID_YUKON_LITE &&
+ chip_rev(hw) == CHIP_REV_YU_LITE_A3) {
+ skge_write32(hw, B2_GP_IO,
+ skge_read32(hw, B2_GP_IO) | GP_DIR_9 | GP_IO_9);
+ }
+
+ skge_gma_write16(hw, port, GM_GP_CTRL,
+ skge_gma_read16(hw, port, GM_GP_CTRL)
+ & ~(GM_GPCR_RX_ENA|GM_GPCR_RX_ENA));
+ skge_gma_read16(hw, port, GM_GP_CTRL);
+
+ /* set GPHY Control reset */
+ skge_gma_write32(hw, port, GPHY_CTRL, GPC_RST_SET);
+ skge_gma_write32(hw, port, GMAC_CTRL, GMC_RST_SET);
+}
+
+static void yukon_get_stats(struct skge_port *skge, u64 *data)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ int i;
+
+ data[0] = (u64) skge_gma_read32(hw, port, GM_TXO_OK_HI) << 32
+ | skge_gma_read32(hw, port, GM_TXO_OK_LO);
+ data[1] = (u64) skge_gma_read32(hw, port, GM_RXO_OK_HI) << 32
+ | skge_gma_read32(hw, port, GM_RXO_OK_LO);
+
+ for (i = 2; i < ARRAY_SIZE(skge_stats); i++)
+ data[i] = skge_gma_read32(hw, port,
+ skge_stats[i].gma_offset);
+}
+
+static void yukon_mac_intr(struct skge_hw *hw, int port)
+{
+ struct skge_port *skge = netdev_priv(hw->dev[port]);
+ u8 status = skge_read8(hw, SKGEMAC_REG(port, GMAC_IRQ_SRC));
+
+ pr_debug("yukon_intr status %x\n", status);
+ if (status & GM_IS_RX_FF_OR) {
+ ++skge->net_stats.rx_fifo_errors;
+ skge_gma_write8(hw, port, RX_GMF_CTRL_T, GMF_CLI_RX_FO);
+ }
+ if (status & GM_IS_TX_FF_UR) {
+ ++skge->net_stats.tx_fifo_errors;
+ skge_gma_write8(hw, port, TX_GMF_CTRL_T, GMF_CLI_TX_FU);
+ }
+
+}
+
+static u16 yukon_speed(const struct skge_hw *hw, u16 aux)
+{
+ if (hw->chip_id == CHIP_ID_YUKON_FE)
+ return (aux & PHY_M_PS_SPEED_100) ? SPEED_100 : SPEED_10;
+
+ switch(aux & PHY_M_PS_SPEED_MSK) {
+ case PHY_M_PS_SPEED_1000:
+ return SPEED_1000;
+ case PHY_M_PS_SPEED_100:
+ return SPEED_100;
+ default:
+ return SPEED_10;
+ }
+}
+
+static void yukon_link_up(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u16 reg;
+
+ pr_debug("yukon_link_up\n");
+
+ /* Enable Transmit FIFO Underrun */
+ skge_write8(hw, GMAC_IRQ_MSK, GMAC_DEF_MSK);
+
+ reg = skge_gma_read16(hw, port, GM_GP_CTRL);
+ if (skge->duplex == DUPLEX_FULL || skge->autoneg == AUTONEG_ENABLE)
+ reg |= GM_GPCR_DUP_FULL;
+
+ /* enable Rx/Tx */
+ reg |= GM_GPCR_RX_ENA | GM_GPCR_TX_ENA;
+ skge_gma_write16(hw, port, GM_GP_CTRL, reg);
+
+ skge_gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
+ skge_link_up(skge);
+}
+
+static void yukon_link_down(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+
+ pr_debug("yukon_link_down\n");
+ skge_gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0);
+ skge_gm_phy_write(hw, port, GM_GP_CTRL,
+ skge_gm_phy_read(hw, port, GM_GP_CTRL)
+ & ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA));
+
+ if (hw->chip_id != CHIP_ID_YUKON_FE &&
+ skge->flow_control == FLOW_MODE_REM_SEND) {
+ /* restore Asymmetric Pause bit */
+ skge_gm_phy_write(hw, port, PHY_MARV_AUNE_ADV,
+ skge_gm_phy_read(hw, port,
+ PHY_MARV_AUNE_ADV)
+ | PHY_M_AN_ASP);
+
+ }
+
+ yukon_reset(hw, port);
+ skge_link_down(skge);
+
+ yukon_init(hw, port);
+}
+
+static void yukon_phy_intr(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ const char *reason = NULL;
+ u16 istatus, phystat;
+
+ istatus = skge_gm_phy_read(hw, port, PHY_MARV_INT_STAT);
+ phystat = skge_gm_phy_read(hw, port, PHY_MARV_PHY_STAT);
+ pr_debug("yukon phy intr istat=%x phy_stat=%x\n", istatus, phystat);
+
+ if (istatus & PHY_M_IS_AN_COMPL) {
+ if (skge_gm_phy_read(hw, port, PHY_MARV_AUNE_LP)
+ & PHY_M_AN_RF) {
+ reason = "remote fault";
+ goto failed;
+ }
+
+ if (!(hw->chip_id == CHIP_ID_YUKON_FE || hw->chip_id == CHIP_ID_YUKON_EC)
+ && (skge_gm_phy_read(hw, port, PHY_MARV_1000T_STAT)
+ & PHY_B_1000S_MSF)) {
+ reason = "master/slave fault";
+ goto failed;
+ }
+
+ if (!(phystat & PHY_M_PS_SPDUP_RES)) {
+ reason = "speed/duplex";
+ goto failed;
+ }
+
+ skge->duplex = (phystat & PHY_M_PS_FULL_DUP)
+ ? DUPLEX_FULL : DUPLEX_HALF;
+ skge->speed = yukon_speed(hw, phystat);
+
+ /* Tx & Rx Pause Enabled bits are at 9..8 */
+ if (hw->chip_id == CHIP_ID_YUKON_XL)
+ phystat >>= 6;
+
+ /* We are using IEEE 802.3z/D5.0 Table 37-4 */
+ switch (phystat & PHY_M_PS_PAUSE_MSK) {
+ case PHY_M_PS_PAUSE_MSK:
+ skge->flow_control = FLOW_MODE_SYMMETRIC;
+ break;
+ case PHY_M_PS_RX_P_EN:
+ skge->flow_control = FLOW_MODE_REM_SEND;
+ break;
+ case PHY_M_PS_TX_P_EN:
+ skge->flow_control = FLOW_MODE_LOC_SEND;
+ break;
+ default:
+ skge->flow_control = FLOW_MODE_NONE;
+ }
+
+ if (skge->flow_control == FLOW_MODE_NONE ||
+ (skge->speed < SPEED_1000 && skge->duplex == DUPLEX_HALF))
+ skge_write8(hw, SKGEMAC_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
+ else
+ skge_write8(hw, SKGEMAC_REG(port, GMAC_CTRL), GMC_PAUSE_ON);
+ yukon_link_up(skge);
+ return;
+ }
+
+ if (istatus & PHY_M_IS_LSP_CHANGE)
+ skge->speed = yukon_speed(hw, phystat);
+
+ if (istatus & PHY_M_IS_DUP_CHANGE)
+ skge->duplex = (phystat & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF;
+ if (istatus & PHY_M_IS_LST_CHANGE) {
+ if (phystat & PHY_M_PS_LINK_UP)
+ yukon_link_up(skge);
+ else
+ yukon_link_down(skge);
+ }
+ return;
+ failed:
+ printk(KERN_ERR PFX "%s: autonegotiation failed (%s)\n",
+ skge->netdev->name, reason);
+
+ /* XXX restart autonegotiation? */
+}
+
+static void skge_ramset(struct skge_hw *hw, u16 q, u32 start, size_t len)
+{
+ u32 end;
+
+ start /= 8;
+ len /= 8;
+ end = start + len - 1;
+
+ skge_write8(hw, RB_ADDR(q, RB_CTRL), RB_RST_CLR);
+ skge_write32(hw, RB_ADDR(q, RB_START), start);
+ skge_write32(hw, RB_ADDR(q, RB_WP), start);
+ skge_write32(hw, RB_ADDR(q, RB_RP), start);
+ skge_write32(hw, RB_ADDR(q, RB_END), end);
+
+ if (q == Q_R1 || q == Q_R2) {
+ /* Set thresholds on receive queue's */
+ skge_write32(hw, RB_ADDR(q, RB_RX_UTPP),
+ start + (2*len)/3);
+ skge_write32(hw, RB_ADDR(q, RB_RX_LTPP),
+ start + (len/3));
+ } else {
+ /* Enable store & forward on Tx queue's because
+ * Tx FIFO is only 4K on Genesis and 1K on Yukon
+ */
+ skge_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_STFWD);
+ }
+
+ skge_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_OP_MD);
+}
+
+/* Setup Bus Memory Interface */
+static void skge_qset(struct skge_port *skge, u16 q,
+ const struct skge_element *e)
+{
+ struct skge_hw *hw = skge->hw;
+ u32 watermark = 0x600;
+ u64 base = skge->dma + (e->desc - skge->mem);
+
+ /* optimization to reduce window on 32bit/33mhz */
+ if ((skge_read16(hw, B0_CTST) & (CS_BUS_CLOCK | CS_BUS_SLOT_SZ)) == 0)
+ watermark /= 2;
+
+ skge_write32(hw, Q_ADDR(q, Q_CSR), CSR_CLR_RESET);
+ skge_write32(hw, Q_ADDR(q, Q_F), watermark);
+ skge_write32(hw, Q_ADDR(q, Q_DA_H), (u32)(base >> 32));
+ skge_write32(hw, Q_ADDR(q, Q_DA_L), (u32)base);
+}
+
+static int skge_up(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u32 chunk, ram_addr;
+ size_t rx_size, tx_size;
+ int err;
+
+ if (netif_msg_ifup(skge))
+ printk(KERN_INFO PFX "%s: enabling interface\n", dev->name);
+
+ rx_size = skge->rx_ring.count * sizeof(struct skge_rx_desc);
+ tx_size = skge->tx_ring.count * sizeof(struct skge_tx_desc);
+ skge->mem_size = tx_size + rx_size;
+ skge->mem = pci_alloc_consistent(hw->pdev, skge->mem_size, &skge->dma);
+ if (!skge->mem)
+ return -ENOMEM;
+
+ memset(skge->mem, 0, skge->mem_size);
+
+ if ((err = skge_ring_alloc(&skge->rx_ring, skge->mem, skge->dma)))
+ goto free_pci_mem;
+
+ if (skge_rx_fill(skge))
+ goto free_rx_ring;
+
+ if ((err = skge_ring_alloc(&skge->tx_ring, skge->mem + rx_size,
+ skge->dma + rx_size)))
+ goto free_rx_ring;
+
+ skge->tx_avail = skge->tx_ring.count - 1;
+
+ /* Initialze MAC */
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ genesis_mac_init(hw, port);
+ else
+ yukon_mac_init(hw, port);
+
+ /* Configure RAMbuffers */
+ chunk = hw->ram_size / (isdualport(hw) ? 4 : 2);
+ ram_addr = hw->ram_offset + 2 * chunk * port;
+
+ skge_ramset(hw, rxqaddr[port], ram_addr, chunk);
+ skge_qset(skge, rxqaddr[port], skge->rx_ring.to_clean);
+
+ BUG_ON(skge->tx_ring.to_use != skge->tx_ring.to_clean);
+ skge_ramset(hw, txqaddr[port], ram_addr+chunk, chunk);
+ skge_qset(skge, txqaddr[port], skge->tx_ring.to_use);
+
+ /* Start receiver BMU */
+ wmb();
+ skge_write8(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_START | CSR_IRQ_CL_F);
+
+ pr_debug("skge_up completed\n");
+ return 0;
+
+ free_rx_ring:
+ skge_rx_clean(skge);
+ kfree(skge->rx_ring.start);
+ free_pci_mem:
+ pci_free_consistent(hw->pdev, skge->mem_size, skge->mem, skge->dma);
+
+ return err;
+}
+
+static int skge_down(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+
+ if (netif_msg_ifdown(skge))
+ printk(KERN_INFO PFX "%s: disabling interface\n", dev->name);
+
+ netif_stop_queue(dev);
+
+ del_timer_sync(&skge->led_blink);
+ del_timer_sync(&skge->link_check);
+
+ /* Stop transmitter */
+ skge_write8(hw, Q_ADDR(txqaddr[port], Q_CSR), CSR_STOP);
+ skge_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL),
+ RB_RST_SET|RB_DIS_OP_MD);
+
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ genesis_stop(skge);
+ else
+ yukon_stop(skge);
+
+ /* Disable Force Sync bit and Enable Alloc bit */
+ skge_write8(hw, SKGEMAC_REG(port, TXA_CTRL),
+ TXA_DIS_FSYNC | TXA_DIS_ALLOC | TXA_STOP_RC);
+
+ /* Stop Interval Timer and Limit Counter of Tx Arbiter */
+ skge_write32(hw, SKGEMAC_REG(port, TXA_ITI_INI), 0L);
+ skge_write32(hw, SKGEMAC_REG(port, TXA_LIM_INI), 0L);
+
+ /* Reset PCI FIFO */
+ skge_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), CSR_SET_RESET);
+ skge_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL), RB_RST_SET);
+
+ /* Reset the RAM Buffer async Tx queue */
+ skge_write8(hw, RB_ADDR(port == 0 ? Q_XA1 : Q_XA2, RB_CTRL), RB_RST_SET);
+ /* stop receiver */
+ skge_write8(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_STOP);
+ skge_write32(hw, RB_ADDR(port ? Q_R2 : Q_R1, RB_CTRL),
+ RB_RST_SET|RB_DIS_OP_MD);
+ skge_write32(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_SET_RESET);
+
+ if (hw->chip_id == CHIP_ID_GENESIS) {
+ skge_write8(hw, SKGEMAC_REG(port, TX_MFF_CTRL2), MFF_RST_SET);
+ skge_write8(hw, SKGEMAC_REG(port, RX_MFF_CTRL2), MFF_RST_SET);
+ skge_write8(hw, SKGEMAC_REG(port, TX_LED_CTRL), LED_STOP);
+ skge_write8(hw, SKGEMAC_REG(port, RX_LED_CTRL), LED_STOP);
+ } else {
+ skge_write8(hw, SKGEMAC_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
+ skge_write8(hw, SKGEMAC_REG(port, TX_GMF_CTRL_T), GMF_RST_SET);
+ }
+
+ /* turn off led's */
+ skge_write16(hw, B0_LED, LED_STAT_OFF);
+
+ skge_tx_clean(skge);
+ skge_rx_clean(skge);
+
+ kfree(skge->rx_ring.start);
+ kfree(skge->tx_ring.start);
+ pci_free_consistent(hw->pdev, skge->mem_size, skge->mem, skge->dma);
+ return 0;
+}
+
+static int skge_xmit_frame(struct sk_buff *skb, struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ struct skge_ring *ring = &skge->tx_ring;
+ struct skge_element *e;
+ struct skge_tx_desc *td;
+ int i;
+ u32 control, len;
+ u64 map;
+ unsigned long flags;
+
+ skb = skb_padto(skb, ETH_ZLEN);
+ if (!skb)
+ return NETDEV_TX_OK;
+
+ local_irq_save(flags);
+ if (!spin_trylock(&skge->tx_lock)) {
+ /* Collision - tell upper layer to requeue */
+ local_irq_restore(flags);
+ return NETDEV_TX_LOCKED;
+ }
+
+ if (unlikely(skge->tx_avail < skb_shinfo(skb)->nr_frags +1)) {
+ netif_stop_queue(dev);
+ spin_unlock_irqrestore(&skge->tx_lock, flags);
+
+ printk(KERN_WARNING PFX "%s: ring full when queue awake!\n",
+ dev->name);
+ return NETDEV_TX_BUSY;
+ }
+
+ e = ring->to_use;
+ td = e->desc;
+ e->skb = skb;
+ len = skb_headlen(skb);
+ map = pci_map_single(hw->pdev, skb->data, len, PCI_DMA_TODEVICE);
+ pci_unmap_addr_set(e, mapaddr, map);
+ pci_unmap_len_set(e, maplen, len);
+
+ td->dma_lo = map;
+ td->dma_hi = map >> 32;
+
+ if (skb->ip_summed == CHECKSUM_HW) {
+ const struct iphdr *ip
+ = (const struct iphdr *) (skb->data + ETH_HLEN);
+ int offset = skb->h.raw - skb->data;
+
+ /* This seems backwards, but it is what the sk98lin
+ * does. Looks like hardware is wrong?
+ */
+ if (ip->protocol == IPPROTO_UDP
+ && chip_rev(hw) == 0 && hw->chip_id == CHIP_ID_YUKON)
+ control = BMU_TCP_CHECK;
+ else
+ control = BMU_UDP_CHECK;
+
+ td->csum_offs = 0;
+ td->csum_start = offset;
+ td->csum_write = offset + skb->csum;
+ } else
+ control = BMU_CHECK;
+
+ if (!skb_shinfo(skb)->nr_frags) /* single buffer i.e. no fragments */
+ control |= BMU_EOF| BMU_IRQ_EOF;
+ else {
+ struct skge_tx_desc *tf = td;
+
+ control |= BMU_STFWD;
+ for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
+ skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
+
+ map = pci_map_page(hw->pdev, frag->page, frag->page_offset,
+ frag->size, PCI_DMA_TODEVICE);
+
+ e = e->next;
+ e->skb = NULL;
+ tf = e->desc;
+ tf->dma_lo = map;
+ tf->dma_hi = (u64) map >> 32;
+ pci_unmap_addr_set(e, mapaddr, map);
+ pci_unmap_len_set(e, maplen, frag->size);
+
+ tf->control = BMU_OWN | BMU_SW | control | frag->size;
+ }
+ tf->control |= BMU_EOF | BMU_IRQ_EOF;
+ }
+ /* Make sure all the descriptors written */
+ wmb();
+ td->control = BMU_OWN | BMU_SW | BMU_STF | control | len;
+ wmb();
+
+ skge_write8(hw, Q_ADDR(txqaddr[skge->port], Q_CSR), CSR_START);
+
+ if (netif_msg_tx_queued(skge))
+ printk(KERN_DEBUG "%s: tx queued, slot %d, len %d\n",
+ dev->name, e - ring->start, skb->len);
+
+ ring->to_use = e->next;
+ skge->tx_avail -= skb_shinfo(skb)->nr_frags + 1;
+ if (skge->tx_avail <= MAX_SKB_FRAGS + 1) {
+ pr_debug("%s: transmit queue full\n", dev->name);
+ netif_stop_queue(dev);
+ }
+
+ dev->trans_start = jiffies;
+ spin_unlock_irqrestore(&skge->tx_lock, flags);
+
+ return NETDEV_TX_OK;
+}
+
+static inline void skge_tx_free(struct skge_hw *hw, struct skge_element *e)
+{
+ if (e->skb) {
+ pci_unmap_single(hw->pdev,
+ pci_unmap_addr(e, mapaddr),
+ pci_unmap_len(e, maplen),
+ PCI_DMA_TODEVICE);
+ dev_kfree_skb_any(e->skb);
+ e->skb = NULL;
+ } else {
+ pci_unmap_page(hw->pdev,
+ pci_unmap_addr(e, mapaddr),
+ pci_unmap_len(e, maplen),
+ PCI_DMA_TODEVICE);
+ }
+}
+
+static void skge_tx_clean(struct skge_port *skge)
+{
+ struct skge_ring *ring = &skge->tx_ring;
+ struct skge_element *e;
+ unsigned long flags;
+
+ spin_lock_irqsave(&skge->tx_lock, flags);
+ for (e = ring->to_clean; e != ring->to_use; e = e->next) {
+ ++skge->tx_avail;
+ skge_tx_free(skge->hw, e);
+ }
+ ring->to_clean = e;
+ spin_unlock_irqrestore(&skge->tx_lock, flags);
+}
+
+static void skge_tx_timeout(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ if (netif_msg_timer(skge))
+ printk(KERN_DEBUG PFX "%s: tx timeout\n", dev->name);
+
+ skge_write8(skge->hw, Q_ADDR(txqaddr[skge->port], Q_CSR), CSR_STOP);
+ skge_tx_clean(skge);
+}
+
+static int skge_change_mtu(struct net_device *dev, int new_mtu)
+{
+ int err = 0;
+
+ if(new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU)
+ return -EINVAL;
+
+ dev->mtu = new_mtu;
+
+ if (netif_running(dev)) {
+ skge_down(dev);
+ skge_up(dev);
+ }
+
+ return err;
+}
+
+static void genesis_set_multicast(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ int i, count = dev->mc_count;
+ struct dev_mc_list *list = dev->mc_list;
+ u32 mode;
+ u8 filter[8];
+
+ mode = skge_xm_read32(hw, port, XM_MODE);
+ mode |= XM_MD_ENA_HASH;
+ if (dev->flags & IFF_PROMISC)
+ mode |= XM_MD_ENA_PROM;
+ else
+ mode &= ~XM_MD_ENA_PROM;
+
+ if (dev->flags & IFF_ALLMULTI)
+ memset(filter, 0xff, sizeof(filter));
+ else {
+ memset(filter, 0, sizeof(filter));
+ for(i = 0; list && i < count; i++, list = list->next) {
+ u32 crc = crc32_le(~0, list->dmi_addr, ETH_ALEN);
+ u8 bit = 63 - (crc & 63);
+
+ filter[bit/8] |= 1 << (bit%8);
+ }
+ }
+
+ skge_xm_outhash(hw, port, XM_HSM, filter);
+
+ skge_xm_write32(hw, port, XM_MODE, mode);
+}
+
+static void yukon_set_multicast(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ struct dev_mc_list *list = dev->mc_list;
+ u16 reg;
+ u8 filter[8];
+
+ memset(filter, 0, sizeof(filter));
+
+ reg = skge_gma_read16(hw, port, GM_RX_CTRL);
+ reg |= GM_RXCR_UCF_ENA;
+
+ if (dev->flags & IFF_PROMISC) /* promiscious */
+ reg &= ~(GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA);
+ else if (dev->flags & IFF_ALLMULTI) /* all multicast */
+ memset(filter, 0xff, sizeof(filter));
+ else if (dev->mc_count == 0) /* no multicast */
+ reg &= ~GM_RXCR_MCF_ENA;
+ else {
+ int i;
+ reg |= GM_RXCR_MCF_ENA;
+
+ for(i = 0; list && i < dev->mc_count; i++, list = list->next) {
+ u32 bit = ether_crc(ETH_ALEN, list->dmi_addr) & 0x3f;
+ filter[bit/8] |= 1 << (bit%8);
+ }
+ }
+
+
+ skge_gma_write16(hw, port, GM_MC_ADDR_H1,
+ (u16)filter[0] | ((u16)filter[1] << 8));
+ skge_gma_write16(hw, port, GM_MC_ADDR_H2,
+ (u16)filter[2] | ((u16)filter[3] << 8));
+ skge_gma_write16(hw, port, GM_MC_ADDR_H3,
+ (u16)filter[4] | ((u16)filter[5] << 8));
+ skge_gma_write16(hw, port, GM_MC_ADDR_H4,
+ (u16)filter[6] | ((u16)filter[7] << 8));
+
+ skge_gma_write16(hw, port, GM_RX_CTRL, reg);
+}
+
+static inline int bad_phy_status(const struct skge_hw *hw, u32 status)
+{
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ return (status & (XMR_FS_ERR | XMR_FS_2L_VLAN)) != 0;
+ else
+ return (status & GMR_FS_ANY_ERR) ||
+ (status & GMR_FS_RX_OK) == 0;
+}
+
+static void skge_rx_error(struct skge_port *skge, int slot,
+ u32 control, u32 status)
+{
+ if (netif_msg_rx_err(skge))
+ printk(KERN_DEBUG PFX "%s: rx err, slot %d control 0x%x status 0x%x\n",
+ skge->netdev->name, slot, control, status);
+
+ if ((control & (BMU_EOF|BMU_STF)) != (BMU_STF|BMU_EOF)
+ || (control & BMU_BBC) > skge->netdev->mtu + VLAN_ETH_HLEN)
+ skge->net_stats.rx_length_errors++;
+ else {
+ if (skge->hw->chip_id == CHIP_ID_GENESIS) {
+ if (status & (XMR_FS_RUNT|XMR_FS_LNG_ERR))
+ skge->net_stats.rx_length_errors++;
+ if (status & XMR_FS_FRA_ERR)
+ skge->net_stats.rx_frame_errors++;
+ if (status & XMR_FS_FCS_ERR)
+ skge->net_stats.rx_crc_errors++;
+ } else {
+ if (status & (GMR_FS_LONG_ERR|GMR_FS_UN_SIZE))
+ skge->net_stats.rx_length_errors++;
+ if (status & GMR_FS_FRAGMENT)
+ skge->net_stats.rx_frame_errors++;
+ if (status & GMR_FS_CRC_ERR)
+ skge->net_stats.rx_crc_errors++;
+ }
+ }
+}
+
+static int skge_poll(struct net_device *dev, int *budget)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ struct skge_ring *ring = &skge->rx_ring;
+ struct skge_element *e;
+ unsigned int to_do = min(dev->quota, *budget);
+ unsigned int work_done = 0;
+ int done;
+ static const u32 irqmask[] = { IS_PORT_1, IS_PORT_2 };
+
+ for (e = ring->to_clean; e != ring->to_use && work_done < to_do;
+ e = e->next) {
+ struct skge_rx_desc *rd = e->desc;
+ struct sk_buff *skb = e->skb;
+ u32 control, len, status;
+
+ rmb();
+ control = rd->control;
+ if (control & BMU_OWN)
+ break;
+
+ len = control & BMU_BBC;
+ e->skb = NULL;
+
+ pci_unmap_single(hw->pdev,
+ pci_unmap_addr(e, mapaddr),
+ pci_unmap_len(e, maplen),
+ PCI_DMA_FROMDEVICE);
+
+ status = rd->status;
+ if ((control & (BMU_EOF|BMU_STF)) != (BMU_STF|BMU_EOF)
+ || len > dev->mtu + VLAN_ETH_HLEN
+ || bad_phy_status(hw, status)) {
+ skge_rx_error(skge, e - ring->start, control, status);
+ dev_kfree_skb(skb);
+ continue;
+ }
+
+ if (netif_msg_rx_status(skge))
+ printk(KERN_DEBUG PFX "%s: rx slot %d status 0x%x len %d\n",
+ dev->name, e - ring->start, rd->status, len);
+
+ skb_put(skb, len);
+ skb->protocol = eth_type_trans(skb, dev);
+
+ if (skge->rx_csum) {
+ skb->csum = le16_to_cpu(rd->csum2);
+ skb->ip_summed = CHECKSUM_HW;
+ }
+
+ dev->last_rx = jiffies;
+ netif_receive_skb(skb);
+
+ ++work_done;
+ }
+ ring->to_clean = e;
+
+ *budget -= work_done;
+ dev->quota -= work_done;
+ done = work_done < to_do;
+
+ if (skge_rx_fill(skge))
+ done = 0;
+
+ /* restart receiver */
+ wmb();
+ skge_write8(hw, Q_ADDR(rxqaddr[skge->port], Q_CSR),
+ CSR_START | CSR_IRQ_CL_F);
+
+ if (done) {
+ local_irq_disable();
+ hw->intr_mask |= irqmask[skge->port];
+ /* Order is important since data can get interrupted */
+ skge_write32(hw, B0_IMSK, hw->intr_mask);
+ __netif_rx_complete(dev);
+ local_irq_enable();
+ }
+
+ return !done;
+}
+
+static inline void skge_tx_intr(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ struct skge_ring *ring = &skge->tx_ring;
+ struct skge_element *e;
+
+ spin_lock(&skge->tx_lock);
+ for(e = ring->to_clean; e != ring->to_use; e = e->next) {
+ struct skge_tx_desc *td = e->desc;
+ u32 control;
+
+ rmb();
+ control = td->control;
+ if (control & BMU_OWN)
+ break;
+
+ if (unlikely(netif_msg_tx_done(skge)))
+ printk(KERN_DEBUG PFX "%s: tx done slot %d status 0x%x\n",
+ dev->name, e - ring->start, td->status);
+
+ skge_tx_free(hw, e);
+ e->skb = NULL;
+ ++skge->tx_avail;
+ }
+ ring->to_clean = e;
+ skge_write8(hw, Q_ADDR(txqaddr[skge->port], Q_CSR), CSR_IRQ_CL_F);
+
+ if (skge->tx_avail > MAX_SKB_FRAGS + 1)
+ netif_wake_queue(dev);
+
+ spin_unlock(&skge->tx_lock);
+}
+
+static void skge_mac_parity(struct skge_hw *hw, int port)
+{
+ printk(KERN_ERR PFX "%s: mac data parity error\n",
+ hw->dev[port] ? hw->dev[port]->name
+ : (port == 0 ? "(port A)": "(port B"));
+
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ skge_write16(hw, SKGEMAC_REG(port, TX_MFF_CTRL1),
+ MFF_CLR_PERR);
+ else
+ /* HW-Bug #8: cleared by GMF_CLI_TX_FC instead of GMF_CLI_TX_PE */
+ skge_write8(hw, SKGEMAC_REG(port, TX_GMF_CTRL_T),
+ (hw->chip_id == CHIP_ID_YUKON && chip_rev(hw) == 0)
+ ? GMF_CLI_TX_FC : GMF_CLI_TX_PE);
+}
+
+static void skge_pci_clear(struct skge_hw *hw)
+{
+ u16 status;
+
+ status = skge_read16(hw, SKGEPCI_REG(PCI_STATUS));
+ skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+ skge_write16(hw, SKGEPCI_REG(PCI_STATUS),
+ status | PCI_STATUS_ERROR_BITS);
+ skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
+}
+
+static void skge_mac_intr(struct skge_hw *hw, int port)
+{
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ genesis_mac_intr(hw, port);
+ else
+ yukon_mac_intr(hw, port);
+}
+
+/* Handle device specific framing and timeout interrupts */
+static void skge_error_irq(struct skge_hw *hw)
+{
+ u32 hwstatus = skge_read32(hw, B0_HWE_ISRC);
+
+ if (hw->chip_id == CHIP_ID_GENESIS) {
+ /* clear xmac errors */
+ if (hwstatus & (IS_NO_STAT_M1|IS_NO_TIST_M1))
+ skge_write16(hw, SKGEMAC_REG(0, RX_MFF_CTRL1), MFF_CLR_INSTAT);
+ if (hwstatus & (IS_NO_STAT_M2|IS_NO_TIST_M2))
+ skge_write16(hw, SKGEMAC_REG(0, RX_MFF_CTRL2), MFF_CLR_INSTAT);
+ } else {
+ /* Timestamp (unused) overflow */
+ if (hwstatus & IS_IRQ_TIST_OV)
+ skge_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ);
+
+ if (hwstatus & IS_IRQ_SENSOR) {
+ /* no sensors on 32-bit Yukon */
+ if (!(skge_read16(hw, B0_CTST) & CS_BUS_SLOT_SZ)) {
+ printk(KERN_ERR PFX "ignoring bogus sensor interrups\n");
+ skge_write32(hw, B0_HWE_IMSK,
+ IS_ERR_MSK & ~IS_IRQ_SENSOR);
+ } else
+ printk(KERN_WARNING PFX "sensor interrupt\n");
+ }
+
+
+ }
+
+ if (hwstatus & IS_RAM_RD_PAR) {
+ printk(KERN_ERR PFX "Ram read data parity error\n");
+ skge_write16(hw, B3_RI_CTRL, RI_CLR_RD_PERR);
+ }
+
+ if (hwstatus & IS_RAM_WR_PAR) {
+ printk(KERN_ERR PFX "Ram write data parity error\n");
+ skge_write16(hw, B3_RI_CTRL, RI_CLR_WR_PERR);
+ }
+
+ if (hwstatus & IS_M1_PAR_ERR)
+ skge_mac_parity(hw, 0);
+
+ if (hwstatus & IS_M2_PAR_ERR)
+ skge_mac_parity(hw, 1);
+
+ if (hwstatus & IS_R1_PAR_ERR)
+ skge_write32(hw, B0_R1_CSR, CSR_IRQ_CL_P);
+
+ if (hwstatus & IS_R2_PAR_ERR)
+ skge_write32(hw, B0_R2_CSR, CSR_IRQ_CL_P);
+
+ if (hwstatus & (IS_IRQ_MST_ERR|IS_IRQ_STAT)) {
+ printk(KERN_ERR PFX "hardware error detected (status 0x%x)\n",
+ hwstatus);
+
+ skge_pci_clear(hw);
+
+ hwstatus = skge_read32(hw, B0_HWE_ISRC);
+ if (hwstatus & IS_IRQ_STAT) {
+ printk(KERN_WARNING PFX "IRQ status %x: still set ignoring hardware errors\n",
+ hwstatus);
+ hw->intr_mask &= ~IS_HW_ERR;
+ }
+ }
+}
+
+/*
+ * Interrrupt from PHY are handled in tasklet (soft irq)
+ * because accessing phy registers requires spin wait which might
+ * cause excess interrupt latency.
+ */
+static void skge_extirq(unsigned long data)
+{
+ struct skge_hw *hw = (struct skge_hw *) data;
+ int port;
+
+ spin_lock(&hw->phy_lock);
+ for (port = 0; port < 2; port++) {
+ struct net_device *dev = hw->dev[port];
+
+ if (dev && netif_running(dev)) {
+ struct skge_port *skge = netdev_priv(dev);
+
+ if (hw->chip_id != CHIP_ID_GENESIS)
+ yukon_phy_intr(skge);
+ else if (hw->phy_type == SK_PHY_BCOM)
+ genesis_bcom_intr(skge);
+ }
+ }
+ spin_unlock(&hw->phy_lock);
+
+ local_irq_disable();
+ hw->intr_mask |= IS_EXT_REG;
+ skge_write32(hw, B0_IMSK, hw->intr_mask);
+ local_irq_enable();
+}
+
+static irqreturn_t skge_intr(int irq, void *dev_id, struct pt_regs *regs)
+{
+ struct skge_hw *hw = dev_id;
+ u32 status = skge_read32(hw, B0_SP_ISRC);
+
+ if (status == 0 || status == ~0) /* hotplug or shared irq */
+ return IRQ_NONE;
+
+ status &= hw->intr_mask;
+
+ if ((status & IS_R1_F) && netif_rx_schedule_prep(hw->dev[0])) {
+ status &= ~IS_R1_F;
+ hw->intr_mask &= ~IS_R1_F;
+ skge_write32(hw, B0_IMSK, hw->intr_mask);
+ __netif_rx_schedule(hw->dev[0]);
+ }
+
+ if ((status & IS_R2_F) && netif_rx_schedule_prep(hw->dev[1])) {
+ status &= ~IS_R2_F;
+ hw->intr_mask &= ~IS_R2_F;
+ skge_write32(hw, B0_IMSK, hw->intr_mask);
+ __netif_rx_schedule(hw->dev[1]);
+ }
+
+ if (status & IS_XA1_F)
+ skge_tx_intr(hw->dev[0]);
+
+ if (status & IS_XA2_F)
+ skge_tx_intr(hw->dev[1]);
+
+ if (status & IS_MAC1)
+ skge_mac_intr(hw, 0);
+
+ if (status & IS_MAC2)
+ skge_mac_intr(hw, 1);
+
+ if (status & IS_HW_ERR)
+ skge_error_irq(hw);
+
+ if (status & IS_EXT_REG) {
+ hw->intr_mask &= ~IS_EXT_REG;
+ tasklet_schedule(&hw->ext_tasklet);
+ }
+
+ if (status)
+ skge_write32(hw, B0_IMSK, hw->intr_mask);
+
+ return IRQ_HANDLED;
+}
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+static void skge_netpoll(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ disable_irq(dev->irq);
+ skge_intr(dev->irq, skge->hw, NULL);
+ enable_irq(dev->irq);
+}
+#endif
+
+static int skge_set_mac_address(struct net_device *dev, void *p)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct sockaddr *addr = p;
+ int err = 0;
+
+ if (!is_valid_ether_addr(addr->sa_data))
+ return -EADDRNOTAVAIL;
+
+ skge_down(dev);
+ memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
+ memcpy_toio(skge->hw->regs + B2_MAC_1 + skge->port*8,
+ dev->dev_addr, ETH_ALEN);
+ memcpy_toio(skge->hw->regs + B2_MAC_2 + skge->port*8,
+ dev->dev_addr, ETH_ALEN);
+ if (dev->flags & IFF_UP)
+ err = skge_up(dev);
+ return err;
+}
+
+static const struct {
+ u8 id;
+ const char *name;
+} skge_chips[] = {
+ { CHIP_ID_GENESIS, "Genesis" },
+ { CHIP_ID_YUKON, "Yukon" },
+ { CHIP_ID_YUKON_LITE, "Yukon-Lite"},
+ { CHIP_ID_YUKON_LP, "Yukon-LP"},
+ { CHIP_ID_YUKON_XL, "Yukon-2 XL"},
+ { CHIP_ID_YUKON_EC, "YUKON-2 EC"},
+ { CHIP_ID_YUKON_FE, "YUKON-2 FE"},
+};
+
+static const char *skge_board_name(const struct skge_hw *hw)
+{
+ int i;
+ static char buf[16];
+
+ for (i = 0; i < ARRAY_SIZE(skge_chips); i++)
+ if (skge_chips[i].id == hw->chip_id)
+ return skge_chips[i].name;
+
+ snprintf(buf, sizeof buf, "chipid 0x%x", hw->chip_id);
+ return buf;
+}
+
+
+/*
+ * Setup the board data structure, but don't bring up
+ * the port(s)
+ */
+static int skge_reset(struct skge_hw *hw)
+{
+ u16 ctst;
+ u8 t8;
+ int i, ports;
+
+ ctst = skge_read16(hw, B0_CTST);
+
+ /* do a SW reset */
+ skge_write8(hw, B0_CTST, CS_RST_SET);
+ skge_write8(hw, B0_CTST, CS_RST_CLR);
+
+ /* clear PCI errors, if any */
+ skge_pci_clear(hw);
+
+ skge_write8(hw, B0_CTST, CS_MRST_CLR);
+
+ /* restore CLK_RUN bits (for Yukon-Lite) */
+ skge_write16(hw, B0_CTST,
+ ctst & (CS_CLK_RUN_HOT|CS_CLK_RUN_RST|CS_CLK_RUN_ENA));
+
+ hw->chip_id = skge_read8(hw, B2_CHIP_ID);
+ hw->phy_type = skge_read8(hw, B2_E_1) & 0xf;
+ hw->pmd_type = skge_read8(hw, B2_PMD_TYP);
+
+ switch(hw->chip_id) {
+ case CHIP_ID_GENESIS:
+ switch (hw->phy_type) {
+ case SK_PHY_XMAC:
+ hw->phy_addr = PHY_ADDR_XMAC;
+ break;
+ case SK_PHY_BCOM:
+ hw->phy_addr = PHY_ADDR_BCOM;
+ break;
+ default:
+ printk(KERN_ERR PFX "%s: unsupported phy type 0x%x\n",
+ pci_name(hw->pdev), hw->phy_type);
+ return -EOPNOTSUPP;
+ }
+ break;
+
+ case CHIP_ID_YUKON:
+ case CHIP_ID_YUKON_LITE:
+ case CHIP_ID_YUKON_LP:
+ if (hw->phy_type < SK_PHY_MARV_COPPER && hw->pmd_type != 'S')
+ hw->phy_type = SK_PHY_MARV_COPPER;
+
+ hw->phy_addr = PHY_ADDR_MARV;
+ if (!iscopper(hw))
+ hw->phy_type = SK_PHY_MARV_FIBER;
+
+ break;
+
+ default:
+ printk(KERN_ERR PFX "%s: unsupported chip type 0x%x\n",
+ pci_name(hw->pdev), hw->chip_id);
+ return -EOPNOTSUPP;
+ }
+
+ hw->mac_cfg = skge_read8(hw, B2_MAC_CFG);
+ ports = isdualport(hw) ? 2 : 1;
+
+ /* read the adapters RAM size */
+ t8 = skge_read8(hw, B2_E_0);
+ if (hw->chip_id == CHIP_ID_GENESIS) {
+ if (t8 == 3) {
+ /* special case: 4 x 64k x 36, offset = 0x80000 */
+ hw->ram_size = 0x100000;
+ hw->ram_offset = 0x80000;
+ } else
+ hw->ram_size = t8 * 512;
+ }
+ else if (t8 == 0)
+ hw->ram_size = 0x20000;
+ else
+ hw->ram_size = t8 * 4096;
+
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ genesis_init(hw);
+ else {
+ /* switch power to VCC (WA for VAUX problem) */
+ skge_write8(hw, B0_POWER_CTRL,
+ PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_OFF | PC_VCC_ON);
+ for (i = 0; i < ports; i++) {
+ skge_write16(hw, SKGEMAC_REG(i, GMAC_LINK_CTRL), GMLC_RST_SET);
+ skge_write16(hw, SKGEMAC_REG(i, GMAC_LINK_CTRL), GMLC_RST_CLR);
+ }
+ }
+
+ /* turn off hardware timer (unused) */
+ skge_write8(hw, B2_TI_CTRL, TIM_STOP);
+ skge_write8(hw, B2_TI_CTRL, TIM_CLR_IRQ);
+ skge_write8(hw, B0_LED, LED_STAT_ON);
+
+ /* enable the Tx Arbiters */
+ for (i = 0; i < ports; i++)
+ skge_write8(hw, SKGEMAC_REG(i, TXA_CTRL), TXA_ENA_ARB);
+
+ /* Initialize ram interface */
+ skge_write16(hw, B3_RI_CTRL, RI_RST_CLR);
+
+ skge_write8(hw, B3_RI_WTO_R1, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_WTO_XA1, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_WTO_XS1, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_RTO_R1, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_RTO_XA1, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_RTO_XS1, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_WTO_R2, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_WTO_XA2, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_WTO_XS2, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_RTO_R2, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_RTO_XA2, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_RTO_XS2, SK_RI_TO_53);
+
+ skge_write32(hw, B0_HWE_IMSK, IS_ERR_MSK);
+
+ /* Set interrupt moderation for Transmit only
+ * Receive interrupts avoided by NAPI
+ */
+ skge_write32(hw, B2_IRQM_MSK, IS_XA1_F|IS_XA2_F);
+ skge_write32(hw, B2_IRQM_INI, skge_usecs2clk(hw, 100));
+ skge_write32(hw, B2_IRQM_CTRL, TIM_START);
+
+ hw->intr_mask = IS_HW_ERR | IS_EXT_REG | IS_PORT_1;
+ if (isdualport(hw))
+ hw->intr_mask |= IS_PORT_2;
+ skge_write32(hw, B0_IMSK, hw->intr_mask);
+
+ if (hw->chip_id != CHIP_ID_GENESIS)
+ skge_write8(hw, GMAC_IRQ_MSK, 0);
+
+ spin_lock_bh(&hw->phy_lock);
+ for (i = 0; i < ports; i++) {
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ genesis_reset(hw, i);
+ else
+ yukon_reset(hw, i);
+ }
+ spin_unlock_bh(&hw->phy_lock);
+
+ return 0;
+}
+
+/* Initialize network device */
+static struct net_device *skge_devinit(struct skge_hw *hw, int port)
+{
+ struct skge_port *skge;
+ struct net_device *dev = alloc_etherdev(sizeof(*skge));
+
+ if (!dev) {
+ printk(KERN_ERR "skge etherdev alloc failed");
+ return NULL;
+ }
+
+ SET_MODULE_OWNER(dev);
+ SET_NETDEV_DEV(dev, &hw->pdev->dev);
+ dev->open = skge_up;
+ dev->stop = skge_down;
+ dev->hard_start_xmit = skge_xmit_frame;
+ dev->get_stats = skge_get_stats;
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ dev->set_multicast_list = genesis_set_multicast;
+ else
+ dev->set_multicast_list = yukon_set_multicast;
+
+ dev->set_mac_address = skge_set_mac_address;
+ dev->change_mtu = skge_change_mtu;
+ SET_ETHTOOL_OPS(dev, &skge_ethtool_ops);
+ dev->tx_timeout = skge_tx_timeout;
+ dev->watchdog_timeo = TX_WATCHDOG;
+ dev->poll = skge_poll;
+ dev->weight = NAPI_WEIGHT;
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ dev->poll_controller = skge_netpoll;
+#endif
+ dev->irq = hw->pdev->irq;
+ dev->features = NETIF_F_LLTX;
+
+ skge = netdev_priv(dev);
+ skge->netdev = dev;
+ skge->hw = hw;
+ skge->msg_enable = netif_msg_init(debug, default_msg);
+ skge->tx_ring.count = DEFAULT_TX_RING_SIZE;
+ skge->rx_ring.count = DEFAULT_RX_RING_SIZE;
+
+ /* Auto speed and flow control */
+ skge->autoneg = AUTONEG_ENABLE;
+ skge->flow_control = FLOW_MODE_SYMMETRIC;
+ skge->duplex = -1;
+ skge->speed = -1;
+ skge->advertising = skge_modes(hw);
+
+ hw->dev[port] = dev;
+
+ skge->port = port;
+
+ spin_lock_init(&skge->tx_lock);
+
+ init_timer(&skge->link_check);
+ skge->link_check.function = skge_link_timer;
+ skge->link_check.data = (unsigned long) skge;
+
+ init_timer(&skge->led_blink);
+ skge->led_blink.function = skge_blink_timer;
+ skge->led_blink.data = (unsigned long) skge;
+
+ if (hw->chip_id != CHIP_ID_GENESIS) {
+ dev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
+ skge->rx_csum = 1;
+ }
+
+ /* read the mac address */
+ memcpy_fromio(dev->dev_addr, hw->regs + B2_MAC_1 + port*8, ETH_ALEN);
+
+ /* device is off until link detection */
+ netif_carrier_off(dev);
+ netif_stop_queue(dev);
+
+ return dev;
+}
+
+static void __devinit skge_show_addr(struct net_device *dev)
+{
+ const struct skge_port *skge = netdev_priv(dev);
+
+ if (netif_msg_probe(skge))
+ printk(KERN_INFO PFX "%s: addr %02x:%02x:%02x:%02x:%02x:%02x\n",
+ dev->name,
+ dev->dev_addr[0], dev->dev_addr[1], dev->dev_addr[2],
+ dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5]);
+}
+
+static int __devinit skge_probe(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ struct net_device *dev, *dev1;
+ struct skge_hw *hw;
+ int err, using_dac = 0;
+
+ if ((err = pci_enable_device(pdev))) {
+ printk(KERN_ERR PFX "%s cannot enable PCI device\n",
+ pci_name(pdev));
+ goto err_out;
+ }
+
+ if ((err = pci_request_regions(pdev, DRV_NAME))) {
+ printk(KERN_ERR PFX "%s cannot obtain PCI resources\n",
+ pci_name(pdev));
+ goto err_out_disable_pdev;
+ }
+
+ pci_set_master(pdev);
+
+ if (!(err = pci_set_dma_mask(pdev, DMA_64BIT_MASK)))
+ using_dac = 1;
+ else if (!(err = pci_set_dma_mask(pdev, DMA_32BIT_MASK))) {
+ printk(KERN_ERR PFX "%s no usable DMA configuration\n",
+ pci_name(pdev));
+ goto err_out_free_regions;
+ }
+
+#ifdef __BIG_ENDIAN
+ /* byte swap decriptors in hardware */
+ {
+ u32 reg;
+
+ pci_read_config_dword(pdev, PCI_DEV_REG2, ®);
+ reg |= PCI_REV_DESC;
+ pci_write_config_dword(pdev, PCI_DEV_REG2, reg);
+ }
+#endif
+
+ err = -ENOMEM;
+ hw = kmalloc(sizeof(*hw), GFP_KERNEL);
+ if (!hw) {
+ printk(KERN_ERR PFX "%s: cannot allocate hardware struct\n",
+ pci_name(pdev));
+ goto err_out_free_regions;
+ }
+
+ memset(hw, 0, sizeof(*hw));
+ hw->pdev = pdev;
+ spin_lock_init(&hw->phy_lock);
+ tasklet_init(&hw->ext_tasklet, skge_extirq, (unsigned long) hw);
+
+ hw->regs = ioremap_nocache(pci_resource_start(pdev, 0), 0x4000);
+ if (!hw->regs) {
+ printk(KERN_ERR PFX "%s: cannot map device registers\n",
+ pci_name(pdev));
+ goto err_out_free_hw;
+ }
+
+ if ((err = request_irq(pdev->irq, skge_intr, SA_SHIRQ, DRV_NAME, hw))) {
+ printk(KERN_ERR PFX "%s: cannot assign irq %d\n",
+ pci_name(pdev), pdev->irq);
+ goto err_out_iounmap;
+ }
+ pci_set_drvdata(pdev, hw);
+
+ err = skge_reset(hw);
+ if (err)
+ goto err_out_free_irq;
+
+ printk(KERN_INFO PFX "addr 0x%lx irq %d chip %s rev %d\n",
+ pci_resource_start(pdev, 0), pdev->irq,
+ skge_board_name(hw), chip_rev(hw));
+
+ if ((dev = skge_devinit(hw, 0)) == NULL)
+ goto err_out_led_off;
+
+ if (using_dac)
+ dev->features |= NETIF_F_HIGHDMA;
+
+ if ((err = register_netdev(dev))) {
+ printk(KERN_ERR PFX "%s: cannot register net device\n",
+ pci_name(pdev));
+ goto err_out_free_netdev;
+ }
+
+ skge_show_addr(dev);
+
+ if (isdualport(hw) && (dev1 = skge_devinit(hw, 1))) {
+ if (using_dac)
+ dev1->features |= NETIF_F_HIGHDMA;
+
+ if (register_netdev(dev1) == 0)
+ skge_show_addr(dev1);
+ else {
+ /* Failure to register second port need not be fatal */
+ printk(KERN_WARNING PFX "register of second port failed\n");
+ hw->dev[1] = NULL;
+ free_netdev(dev1);
+ }
+ }
+
+ return 0;
+
+err_out_free_netdev:
+ free_netdev(dev);
+err_out_led_off:
+ skge_write16(hw, B0_LED, LED_STAT_OFF);
+err_out_free_irq:
+ free_irq(pdev->irq, hw);
+err_out_iounmap:
+ iounmap(hw->regs);
+err_out_free_hw:
+ kfree(hw);
+err_out_free_regions:
+ pci_release_regions(pdev);
+err_out_disable_pdev:
+ pci_disable_device(pdev);
+ pci_set_drvdata(pdev, NULL);
+err_out:
+ return err;
+}
+
+static void __devexit skge_remove(struct pci_dev *pdev)
+{
+ struct skge_hw *hw = pci_get_drvdata(pdev);
+ struct net_device *dev0, *dev1;
+
+ if(!hw)
+ return;
+
+ if ((dev1 = hw->dev[1]))
+ unregister_netdev(dev1);
+ dev0 = hw->dev[0];
+ unregister_netdev(dev0);
+
+ tasklet_kill(&hw->ext_tasklet);
+
+ free_irq(pdev->irq, hw);
+ pci_release_regions(pdev);
+ pci_disable_device(pdev);
+ if (dev1)
+ free_netdev(dev1);
+ free_netdev(dev0);
+ skge_write16(hw, B0_LED, LED_STAT_OFF);
+ iounmap(hw->regs);
+ kfree(hw);
+ pci_set_drvdata(pdev, NULL);
+}
+
+#ifdef CONFIG_PM
+static int skge_suspend(struct pci_dev *pdev, u32 state)
+{
+ struct skge_hw *hw = pci_get_drvdata(pdev);
+ int i, wol = 0;
+
+ for(i = 0; i < 2; i++) {
+ struct net_device *dev = hw->dev[i];
+
+ if (dev) {
+ struct skge_port *skge = netdev_priv(dev);
+ if (netif_running(dev)) {
+ netif_carrier_off(dev);
+ skge_down(dev);
+ }
+ netif_device_detach(dev);
+ wol |= skge->wol;
+ }
+ }
+
+ pci_save_state(pdev);
+ pci_enable_wake(pdev, state, wol);
+ pci_disable_device(pdev);
+ pci_set_power_state(pdev, pci_choose_state(pdev, state));
+
+ return 0;
+}
+
+static int skge_resume(struct pci_dev *pdev)
+{
+ struct skge_hw *hw = pci_get_drvdata(pdev);
+ int i;
+
+ pci_set_power_state(pdev, PCI_D0);
+ pci_restore_state(pdev);
+ pci_enable_wake(pdev, PCI_D0, 0);
+
+ skge_reset(hw);
+
+ for(i = 0; i < 2; i++) {
+ struct net_device *dev = hw->dev[i];
+ if (dev) {
+ netif_device_attach(dev);
+ if(netif_running(dev))
+ skge_up(dev);
+ }
+ }
+ return 0;
+}
+#endif
+
+static struct pci_driver skge_driver = {
+ .name = DRV_NAME,
+ .id_table = skge_id_table,
+ .probe = skge_probe,
+ .remove = __devexit_p(skge_remove),
+#ifdef CONFIG_PM
+ .suspend = skge_suspend,
+ .resume = skge_resume,
+#endif
+};
+
+static int __init skge_init_module(void)
+{
+ return pci_module_init(&skge_driver);
+}
+
+static void __exit skge_cleanup_module(void)
+{
+ pci_unregister_driver(&skge_driver);
+}
+
+module_init(skge_init_module);
+module_exit(skge_cleanup_module);
--- /dev/null
+/*
+ * Definitions for the new Marvell Yukon / SysKonenct driver.
+ */
+#ifndef _SKGE_H
+#define _SKGE_H
+
+/* PCI config registers */
+#define PCI_DEV_REG1 0x40
+#define PCI_DEV_REG2 0x44
+#ifndef PCI_VPD
+#define PCI_VPD 0x50
+#endif
+
+/* PCI_OUR_REG_2 32 bit Our Register 2 */
+enum {
+ PCI_VPD_WR_THR = 0xff<<24, /* Bit 31..24: VPD Write Threshold */
+ PCI_DEV_SEL = 0x7f<<17, /* Bit 23..17: EEPROM Device Select */
+ PCI_VPD_ROM_SZ = 7 <<14, /* Bit 16..14: VPD ROM Size */
+ /* Bit 13..12: reserved */
+ PCI_EN_DUMMY_RD = 1<<3, /* Enable Dummy Read */
+ PCI_REV_DESC = 1<<2, /* Reverse Desc. Bytes */
+ PCI_USEDATA64 = 1<<0, /* Use 64Bit Data bus ext */
+};
+
+/* PCI_VPD_ADR_REG 16 bit VPD Address Register */
+enum {
+ PCI_VPD_FLAG = 1<<15, /* starts VPD rd/wr cycle */
+ PCI_VPD_ADR_MSK =0x7fffL, /* Bit 14.. 0: VPD Address Mask */
+ VPD_RES_ID = 0x82,
+ VPD_RES_READ = 0x90,
+ VPD_RES_WRITE = 0x81,
+ VPD_RES_END = 0x78,
+};
+
+
+#define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
+ PCI_STATUS_SIG_SYSTEM_ERROR | \
+ PCI_STATUS_REC_MASTER_ABORT | \
+ PCI_STATUS_REC_TARGET_ABORT | \
+ PCI_STATUS_PARITY)
+
+
+enum csr_regs {
+ B0_RAP = 0x0000,
+ B0_CTST = 0x0004,
+ B0_LED = 0x0006,
+ B0_POWER_CTRL = 0x0007,
+ B0_ISRC = 0x0008,
+ B0_IMSK = 0x000c,
+ B0_HWE_ISRC = 0x0010,
+ B0_HWE_IMSK = 0x0014,
+ B0_SP_ISRC = 0x0018,
+ B0_XM1_IMSK = 0x0020,
+ B0_XM1_ISRC = 0x0028,
+ B0_XM1_PHY_ADDR = 0x0030,
+ B0_XM1_PHY_DATA = 0x0034,
+ B0_XM2_IMSK = 0x0040,
+ B0_XM2_ISRC = 0x0048,
+ B0_XM2_PHY_ADDR = 0x0050,
+ B0_XM2_PHY_DATA = 0x0054,
+ B0_R1_CSR = 0x0060,
+ B0_R2_CSR = 0x0064,
+ B0_XS1_CSR = 0x0068,
+ B0_XA1_CSR = 0x006c,
+ B0_XS2_CSR = 0x0070,
+ B0_XA2_CSR = 0x0074,
+
+ B2_MAC_1 = 0x0100,
+ B2_MAC_2 = 0x0108,
+ B2_MAC_3 = 0x0110,
+ B2_CONN_TYP = 0x0118,
+ B2_PMD_TYP = 0x0119,
+ B2_MAC_CFG = 0x011a,
+ B2_CHIP_ID = 0x011b,
+ B2_E_0 = 0x011c,
+ B2_E_1 = 0x011d,
+ B2_E_2 = 0x011e,
+ B2_E_3 = 0x011f,
+ B2_FAR = 0x0120,
+ B2_FDP = 0x0124,
+ B2_LD_CTRL = 0x0128,
+ B2_LD_TEST = 0x0129,
+ B2_TI_INI = 0x0130,
+ B2_TI_VAL = 0x0134,
+ B2_TI_CTRL = 0x0138,
+ B2_TI_TEST = 0x0139,
+ B2_IRQM_INI = 0x0140,
+ B2_IRQM_VAL = 0x0144,
+ B2_IRQM_CTRL = 0x0148,
+ B2_IRQM_TEST = 0x0149,
+ B2_IRQM_MSK = 0x014c,
+ B2_IRQM_HWE_MSK = 0x0150,
+ B2_TST_CTRL1 = 0x0158,
+ B2_TST_CTRL2 = 0x0159,
+ B2_GP_IO = 0x015c,
+ B2_I2C_CTRL = 0x0160,
+ B2_I2C_DATA = 0x0164,
+ B2_I2C_IRQ = 0x0168,
+ B2_I2C_SW = 0x016c,
+ B2_BSC_INI = 0x0170,
+ B2_BSC_VAL = 0x0174,
+ B2_BSC_CTRL = 0x0178,
+ B2_BSC_STAT = 0x0179,
+ B2_BSC_TST = 0x017a,
+
+ B3_RAM_ADDR = 0x0180,
+ B3_RAM_DATA_LO = 0x0184,
+ B3_RAM_DATA_HI = 0x0188,
+ B3_RI_WTO_R1 = 0x0190,
+ B3_RI_WTO_XA1 = 0x0191,
+ B3_RI_WTO_XS1 = 0x0192,
+ B3_RI_RTO_R1 = 0x0193,
+ B3_RI_RTO_XA1 = 0x0194,
+ B3_RI_RTO_XS1 = 0x0195,
+ B3_RI_WTO_R2 = 0x0196,
+ B3_RI_WTO_XA2 = 0x0197,
+ B3_RI_WTO_XS2 = 0x0198,
+ B3_RI_RTO_R2 = 0x0199,
+ B3_RI_RTO_XA2 = 0x019a,
+ B3_RI_RTO_XS2 = 0x019b,
+ B3_RI_TO_VAL = 0x019c,
+ B3_RI_CTRL = 0x01a0,
+ B3_RI_TEST = 0x01a2,
+ B3_MA_TOINI_RX1 = 0x01b0,
+ B3_MA_TOINI_RX2 = 0x01b1,
+ B3_MA_TOINI_TX1 = 0x01b2,
+ B3_MA_TOINI_TX2 = 0x01b3,
+ B3_MA_TOVAL_RX1 = 0x01b4,
+ B3_MA_TOVAL_RX2 = 0x01b5,
+ B3_MA_TOVAL_TX1 = 0x01b6,
+ B3_MA_TOVAL_TX2 = 0x01b7,
+ B3_MA_TO_CTRL = 0x01b8,
+ B3_MA_TO_TEST = 0x01ba,
+ B3_MA_RCINI_RX1 = 0x01c0,
+ B3_MA_RCINI_RX2 = 0x01c1,
+ B3_MA_RCINI_TX1 = 0x01c2,
+ B3_MA_RCINI_TX2 = 0x01c3,
+ B3_MA_RCVAL_RX1 = 0x01c4,
+ B3_MA_RCVAL_RX2 = 0x01c5,
+ B3_MA_RCVAL_TX1 = 0x01c6,
+ B3_MA_RCVAL_TX2 = 0x01c7,
+ B3_MA_RC_CTRL = 0x01c8,
+ B3_MA_RC_TEST = 0x01ca,
+ B3_PA_TOINI_RX1 = 0x01d0,
+ B3_PA_TOINI_RX2 = 0x01d4,
+ B3_PA_TOINI_TX1 = 0x01d8,
+ B3_PA_TOINI_TX2 = 0x01dc,
+ B3_PA_TOVAL_RX1 = 0x01e0,
+ B3_PA_TOVAL_RX2 = 0x01e4,
+ B3_PA_TOVAL_TX1 = 0x01e8,
+ B3_PA_TOVAL_TX2 = 0x01ec,
+ B3_PA_CTRL = 0x01f0,
+ B3_PA_TEST = 0x01f2,
+};
+
+/* B0_CTST 16 bit Control/Status register */
+enum {
+ CS_CLK_RUN_HOT = 1<<13,/* CLK_RUN hot m. (YUKON-Lite only) */
+ CS_CLK_RUN_RST = 1<<12,/* CLK_RUN reset (YUKON-Lite only) */
+ CS_CLK_RUN_ENA = 1<<11,/* CLK_RUN enable (YUKON-Lite only) */
+ CS_VAUX_AVAIL = 1<<10,/* VAUX available (YUKON only) */
+ CS_BUS_CLOCK = 1<<9, /* Bus Clock 0/1 = 33/66 MHz */
+ CS_BUS_SLOT_SZ = 1<<8, /* Slot Size 0/1 = 32/64 bit slot */
+ CS_ST_SW_IRQ = 1<<7, /* Set IRQ SW Request */
+ CS_CL_SW_IRQ = 1<<6, /* Clear IRQ SW Request */
+ CS_STOP_DONE = 1<<5, /* Stop Master is finished */
+ CS_STOP_MAST = 1<<4, /* Command Bit to stop the master */
+ CS_MRST_CLR = 1<<3, /* Clear Master reset */
+ CS_MRST_SET = 1<<2, /* Set Master reset */
+ CS_RST_CLR = 1<<1, /* Clear Software reset */
+ CS_RST_SET = 1, /* Set Software reset */
+
+/* B0_LED 8 Bit LED register */
+/* Bit 7.. 2: reserved */
+ LED_STAT_ON = 1<<1, /* Status LED on */
+ LED_STAT_OFF = 1, /* Status LED off */
+
+/* B0_POWER_CTRL 8 Bit Power Control reg (YUKON only) */
+ PC_VAUX_ENA = 1<<7, /* Switch VAUX Enable */
+ PC_VAUX_DIS = 1<<6, /* Switch VAUX Disable */
+ PC_VCC_ENA = 1<<5, /* Switch VCC Enable */
+ PC_VCC_DIS = 1<<4, /* Switch VCC Disable */
+ PC_VAUX_ON = 1<<3, /* Switch VAUX On */
+ PC_VAUX_OFF = 1<<2, /* Switch VAUX Off */
+ PC_VCC_ON = 1<<1, /* Switch VCC On */
+ PC_VCC_OFF = 1<<0, /* Switch VCC Off */
+};
+
+/* B2_IRQM_MSK 32 bit IRQ Moderation Mask */
+enum {
+ IS_ALL_MSK = 0xbffffffful, /* All Interrupt bits */
+ IS_HW_ERR = 1<<31, /* Interrupt HW Error */
+ /* Bit 30: reserved */
+ IS_PA_TO_RX1 = 1<<29, /* Packet Arb Timeout Rx1 */
+ IS_PA_TO_RX2 = 1<<28, /* Packet Arb Timeout Rx2 */
+ IS_PA_TO_TX1 = 1<<27, /* Packet Arb Timeout Tx1 */
+ IS_PA_TO_TX2 = 1<<26, /* Packet Arb Timeout Tx2 */
+ IS_I2C_READY = 1<<25, /* IRQ on end of I2C Tx */
+ IS_IRQ_SW = 1<<24, /* SW forced IRQ */
+ IS_EXT_REG = 1<<23, /* IRQ from LM80 or PHY (GENESIS only) */
+ /* IRQ from PHY (YUKON only) */
+ IS_TIMINT = 1<<22, /* IRQ from Timer */
+ IS_MAC1 = 1<<21, /* IRQ from MAC 1 */
+ IS_LNK_SYNC_M1 = 1<<20, /* Link Sync Cnt wrap MAC 1 */
+ IS_MAC2 = 1<<19, /* IRQ from MAC 2 */
+ IS_LNK_SYNC_M2 = 1<<18, /* Link Sync Cnt wrap MAC 2 */
+/* Receive Queue 1 */
+ IS_R1_B = 1<<17, /* Q_R1 End of Buffer */
+ IS_R1_F = 1<<16, /* Q_R1 End of Frame */
+ IS_R1_C = 1<<15, /* Q_R1 Encoding Error */
+/* Receive Queue 2 */
+ IS_R2_B = 1<<14, /* Q_R2 End of Buffer */
+ IS_R2_F = 1<<13, /* Q_R2 End of Frame */
+ IS_R2_C = 1<<12, /* Q_R2 Encoding Error */
+/* Synchronous Transmit Queue 1 */
+ IS_XS1_B = 1<<11, /* Q_XS1 End of Buffer */
+ IS_XS1_F = 1<<10, /* Q_XS1 End of Frame */
+ IS_XS1_C = 1<<9, /* Q_XS1 Encoding Error */
+/* Asynchronous Transmit Queue 1 */
+ IS_XA1_B = 1<<8, /* Q_XA1 End of Buffer */
+ IS_XA1_F = 1<<7, /* Q_XA1 End of Frame */
+ IS_XA1_C = 1<<6, /* Q_XA1 Encoding Error */
+/* Synchronous Transmit Queue 2 */
+ IS_XS2_B = 1<<5, /* Q_XS2 End of Buffer */
+ IS_XS2_F = 1<<4, /* Q_XS2 End of Frame */
+ IS_XS2_C = 1<<3, /* Q_XS2 Encoding Error */
+/* Asynchronous Transmit Queue 2 */
+ IS_XA2_B = 1<<2, /* Q_XA2 End of Buffer */
+ IS_XA2_F = 1<<1, /* Q_XA2 End of Frame */
+ IS_XA2_C = 1<<0, /* Q_XA2 Encoding Error */
+
+ IS_PORT_1 = IS_XA1_F| IS_R1_F| IS_MAC1,
+ IS_PORT_2 = IS_XA2_F| IS_R2_F| IS_MAC2,
+};
+
+
+/* B2_IRQM_HWE_MSK 32 bit IRQ Moderation HW Error Mask */
+enum {
+ IS_ERR_MSK = 0x00003fff,/* All Error bits */
+
+ IS_IRQ_TIST_OV = 1<<13, /* Time Stamp Timer Overflow (YUKON only) */
+ IS_IRQ_SENSOR = 1<<12, /* IRQ from Sensor (YUKON only) */
+ IS_IRQ_MST_ERR = 1<<11, /* IRQ master error detected */
+ IS_IRQ_STAT = 1<<10, /* IRQ status exception */
+ IS_NO_STAT_M1 = 1<<9, /* No Rx Status from MAC 1 */
+ IS_NO_STAT_M2 = 1<<8, /* No Rx Status from MAC 2 */
+ IS_NO_TIST_M1 = 1<<7, /* No Time Stamp from MAC 1 */
+ IS_NO_TIST_M2 = 1<<6, /* No Time Stamp from MAC 2 */
+ IS_RAM_RD_PAR = 1<<5, /* RAM Read Parity Error */
+ IS_RAM_WR_PAR = 1<<4, /* RAM Write Parity Error */
+ IS_M1_PAR_ERR = 1<<3, /* MAC 1 Parity Error */
+ IS_M2_PAR_ERR = 1<<2, /* MAC 2 Parity Error */
+ IS_R1_PAR_ERR = 1<<1, /* Queue R1 Parity Error */
+ IS_R2_PAR_ERR = 1<<0, /* Queue R2 Parity Error */
+};
+
+/* B2_TST_CTRL1 8 bit Test Control Register 1 */
+enum {
+ TST_FRC_DPERR_MR = 1<<7, /* force DATAPERR on MST RD */
+ TST_FRC_DPERR_MW = 1<<6, /* force DATAPERR on MST WR */
+ TST_FRC_DPERR_TR = 1<<5, /* force DATAPERR on TRG RD */
+ TST_FRC_DPERR_TW = 1<<4, /* force DATAPERR on TRG WR */
+ TST_FRC_APERR_M = 1<<3, /* force ADDRPERR on MST */
+ TST_FRC_APERR_T = 1<<2, /* force ADDRPERR on TRG */
+ TST_CFG_WRITE_ON = 1<<1, /* Enable Config Reg WR */
+ TST_CFG_WRITE_OFF= 1<<0, /* Disable Config Reg WR */
+};
+
+/* B2_MAC_CFG 8 bit MAC Configuration / Chip Revision */
+enum {
+ CFG_CHIP_R_MSK = 0xf<<4, /* Bit 7.. 4: Chip Revision */
+ /* Bit 3.. 2: reserved */
+ CFG_DIS_M2_CLK = 1<<1, /* Disable Clock for 2nd MAC */
+ CFG_SNG_MAC = 1<<0, /* MAC Config: 0=2 MACs / 1=1 MAC*/
+};
+
+/* B2_CHIP_ID 8 bit Chip Identification Number */
+enum {
+ CHIP_ID_GENESIS = 0x0a, /* Chip ID for GENESIS */
+ CHIP_ID_YUKON = 0xb0, /* Chip ID for YUKON */
+ CHIP_ID_YUKON_LITE = 0xb1, /* Chip ID for YUKON-Lite (Rev. A1-A3) */
+ CHIP_ID_YUKON_LP = 0xb2, /* Chip ID for YUKON-LP */
+ CHIP_ID_YUKON_XL = 0xb3, /* Chip ID for YUKON-2 XL */
+ CHIP_ID_YUKON_EC = 0xb6, /* Chip ID for YUKON-2 EC */
+ CHIP_ID_YUKON_FE = 0xb7, /* Chip ID for YUKON-2 FE */
+
+ CHIP_REV_YU_LITE_A1 = 3, /* Chip Rev. for YUKON-Lite A1,A2 */
+ CHIP_REV_YU_LITE_A3 = 7, /* Chip Rev. for YUKON-Lite A3 */
+};
+
+/* B2_LD_TEST 8 bit EPROM loader test register */
+enum {
+ LD_T_ON = 1<<3, /* Loader Test mode on */
+ LD_T_OFF = 1<<2, /* Loader Test mode off */
+ LD_T_STEP = 1<<1, /* Decrement FPROM addr. Counter */
+ LD_START = 1<<0, /* Start loading FPROM */
+};
+
+/* B2_TI_CTRL 8 bit Timer control */
+/* B2_IRQM_CTRL 8 bit IRQ Moderation Timer Control */
+enum {
+ TIM_START = 1<<2, /* Start Timer */
+ TIM_STOP = 1<<1, /* Stop Timer */
+ TIM_CLR_IRQ = 1<<0, /* Clear Timer IRQ (!IRQM) */
+};
+
+/* B2_TI_TEST 8 Bit Timer Test */
+/* B2_IRQM_TEST 8 bit IRQ Moderation Timer Test */
+/* B28_DPT_TST 8 bit Descriptor Poll Timer Test Reg */
+enum {
+ TIM_T_ON = 1<<2, /* Test mode on */
+ TIM_T_OFF = 1<<1, /* Test mode off */
+ TIM_T_STEP = 1<<0, /* Test step */
+};
+
+/* B28_DPT_INI 32 bit Descriptor Poll Timer Init Val */
+/* B28_DPT_VAL 32 bit Descriptor Poll Timer Curr Val */
+/* B28_DPT_CTRL 8 bit Descriptor Poll Timer Ctrl Reg */
+enum {
+ DPT_MSK = 0x00ffffffL, /* Bit 23.. 0: Desc Poll Timer Bits */
+
+ DPT_START = 1<<1, /* Start Descriptor Poll Timer */
+ DPT_STOP = 1<<0, /* Stop Descriptor Poll Timer */
+};
+
+/* B2_GP_IO 32 bit General Purpose I/O Register */
+enum {
+ GP_DIR_9 = 1<<25, /* IO_9 direct, 0=In/1=Out */
+ GP_DIR_8 = 1<<24, /* IO_8 direct, 0=In/1=Out */
+ GP_DIR_7 = 1<<23, /* IO_7 direct, 0=In/1=Out */
+ GP_DIR_6 = 1<<22, /* IO_6 direct, 0=In/1=Out */
+ GP_DIR_5 = 1<<21, /* IO_5 direct, 0=In/1=Out */
+ GP_DIR_4 = 1<<20, /* IO_4 direct, 0=In/1=Out */
+ GP_DIR_3 = 1<<19, /* IO_3 direct, 0=In/1=Out */
+ GP_DIR_2 = 1<<18, /* IO_2 direct, 0=In/1=Out */
+ GP_DIR_1 = 1<<17, /* IO_1 direct, 0=In/1=Out */
+ GP_DIR_0 = 1<<16, /* IO_0 direct, 0=In/1=Out */
+
+ GP_IO_9 = 1<<9, /* IO_9 pin */
+ GP_IO_8 = 1<<8, /* IO_8 pin */
+ GP_IO_7 = 1<<7, /* IO_7 pin */
+ GP_IO_6 = 1<<6, /* IO_6 pin */
+ GP_IO_5 = 1<<5, /* IO_5 pin */
+ GP_IO_4 = 1<<4, /* IO_4 pin */
+ GP_IO_3 = 1<<3, /* IO_3 pin */
+ GP_IO_2 = 1<<2, /* IO_2 pin */
+ GP_IO_1 = 1<<1, /* IO_1 pin */
+ GP_IO_0 = 1<<0, /* IO_0 pin */
+};
+
+/* Rx/Tx Path related Arbiter Test Registers */
+/* B3_MA_TO_TEST 16 bit MAC Arbiter Timeout Test Reg */
+/* B3_MA_RC_TEST 16 bit MAC Arbiter Recovery Test Reg */
+/* B3_PA_TEST 16 bit Packet Arbiter Test Register */
+/* Bit 15, 11, 7, and 3 are reserved in B3_PA_TEST */
+enum {
+ TX2_T_EV = 1<<15,/* TX2 Timeout/Recv Event occured */
+ TX2_T_ON = 1<<14,/* TX2 Timeout/Recv Timer Test On */
+ TX2_T_OFF = 1<<13,/* TX2 Timeout/Recv Timer Tst Off */
+ TX2_T_STEP = 1<<12,/* TX2 Timeout/Recv Timer Step */
+ TX1_T_EV = 1<<11,/* TX1 Timeout/Recv Event occured */
+ TX1_T_ON = 1<<10,/* TX1 Timeout/Recv Timer Test On */
+ TX1_T_OFF = 1<<9, /* TX1 Timeout/Recv Timer Tst Off */
+ TX1_T_STEP = 1<<8, /* TX1 Timeout/Recv Timer Step */
+ RX2_T_EV = 1<<7, /* RX2 Timeout/Recv Event occured */
+ RX2_T_ON = 1<<6, /* RX2 Timeout/Recv Timer Test On */
+ RX2_T_OFF = 1<<5, /* RX2 Timeout/Recv Timer Tst Off */
+ RX2_T_STEP = 1<<4, /* RX2 Timeout/Recv Timer Step */
+ RX1_T_EV = 1<<3, /* RX1 Timeout/Recv Event occured */
+ RX1_T_ON = 1<<2, /* RX1 Timeout/Recv Timer Test On */
+ RX1_T_OFF = 1<<1, /* RX1 Timeout/Recv Timer Tst Off */
+ RX1_T_STEP = 1<<0, /* RX1 Timeout/Recv Timer Step */
+};
+
+/* Descriptor Bit Definition */
+/* TxCtrl Transmit Buffer Control Field */
+/* RxCtrl Receive Buffer Control Field */
+enum {
+ BMU_OWN = 1<<31, /* OWN bit: 0=host/1=BMU */
+ BMU_STF = 1<<30, /* Start of Frame */
+ BMU_EOF = 1<<29, /* End of Frame */
+ BMU_IRQ_EOB = 1<<28, /* Req "End of Buffer" IRQ */
+ BMU_IRQ_EOF = 1<<27, /* Req "End of Frame" IRQ */
+ /* TxCtrl specific bits */
+ BMU_STFWD = 1<<26, /* (Tx) Store & Forward Frame */
+ BMU_NO_FCS = 1<<25, /* (Tx) Disable MAC FCS (CRC) generation */
+ BMU_SW = 1<<24, /* (Tx) 1 bit res. for SW use */
+ /* RxCtrl specific bits */
+ BMU_DEV_0 = 1<<26, /* (Rx) Transfer data to Dev0 */
+ BMU_STAT_VAL = 1<<25, /* (Rx) Rx Status Valid */
+ BMU_TIST_VAL = 1<<24, /* (Rx) Rx TimeStamp Valid */
+ /* Bit 23..16: BMU Check Opcodes */
+ BMU_CHECK = 0x55<<16, /* Default BMU check */
+ BMU_TCP_CHECK = 0x56<<16, /* Descr with TCP ext */
+ BMU_UDP_CHECK = 0x57<<16, /* Descr with UDP ext (YUKON only) */
+ BMU_BBC = 0xffffL, /* Bit 15.. 0: Buffer Byte Counter */
+};
+
+/* B2_BSC_CTRL 8 bit Blink Source Counter Control */
+enum {
+ BSC_START = 1<<1, /* Start Blink Source Counter */
+ BSC_STOP = 1<<0, /* Stop Blink Source Counter */
+};
+
+/* B2_BSC_STAT 8 bit Blink Source Counter Status */
+enum {
+ BSC_SRC = 1<<0, /* Blink Source, 0=Off / 1=On */
+};
+
+/* B2_BSC_TST 16 bit Blink Source Counter Test Reg */
+enum {
+ BSC_T_ON = 1<<2, /* Test mode on */
+ BSC_T_OFF = 1<<1, /* Test mode off */
+ BSC_T_STEP = 1<<0, /* Test step */
+};
+
+/* B3_RAM_ADDR 32 bit RAM Address, to read or write */
+ /* Bit 31..19: reserved */
+#define RAM_ADR_RAN 0x0007ffffL /* Bit 18.. 0: RAM Address Range */
+/* RAM Interface Registers */
+
+/* B3_RI_CTRL 16 bit RAM Iface Control Register */
+enum {
+ RI_CLR_RD_PERR = 1<<9, /* Clear IRQ RAM Read Parity Err */
+ RI_CLR_WR_PERR = 1<<8, /* Clear IRQ RAM Write Parity Err*/
+
+ RI_RST_CLR = 1<<1, /* Clear RAM Interface Reset */
+ RI_RST_SET = 1<<0, /* Set RAM Interface Reset */
+};
+
+/* B3_RI_TEST 8 bit RAM Iface Test Register */
+enum {
+ RI_T_EV = 1<<3, /* Timeout Event occured */
+ RI_T_ON = 1<<2, /* Timeout Timer Test On */
+ RI_T_OFF = 1<<1, /* Timeout Timer Test Off */
+ RI_T_STEP = 1<<0, /* Timeout Timer Step */
+};
+
+/* MAC Arbiter Registers */
+/* B3_MA_TO_CTRL 16 bit MAC Arbiter Timeout Ctrl Reg */
+enum {
+ MA_FOE_ON = 1<<3, /* XMAC Fast Output Enable ON */
+ MA_FOE_OFF = 1<<2, /* XMAC Fast Output Enable OFF */
+ MA_RST_CLR = 1<<1, /* Clear MAC Arbiter Reset */
+ MA_RST_SET = 1<<0, /* Set MAC Arbiter Reset */
+
+};
+
+/* Timeout values */
+#define SK_MAC_TO_53 72 /* MAC arbiter timeout */
+#define SK_PKT_TO_53 0x2000 /* Packet arbiter timeout */
+#define SK_PKT_TO_MAX 0xffff /* Maximum value */
+#define SK_RI_TO_53 36 /* RAM interface timeout */
+
+
+/* B3_MA_RC_CTRL 16 bit MAC Arbiter Recovery Ctrl Reg */
+enum {
+ MA_ENA_REC_TX2 = 1<<7, /* Enable Recovery Timer TX2 */
+ MA_DIS_REC_TX2 = 1<<6, /* Disable Recovery Timer TX2 */
+ MA_ENA_REC_TX1 = 1<<5, /* Enable Recovery Timer TX1 */
+ MA_DIS_REC_TX1 = 1<<4, /* Disable Recovery Timer TX1 */
+ MA_ENA_REC_RX2 = 1<<3, /* Enable Recovery Timer RX2 */
+ MA_DIS_REC_RX2 = 1<<2, /* Disable Recovery Timer RX2 */
+ MA_ENA_REC_RX1 = 1<<1, /* Enable Recovery Timer RX1 */
+ MA_DIS_REC_RX1 = 1<<0, /* Disable Recovery Timer RX1 */
+};
+
+/* Packet Arbiter Registers */
+/* B3_PA_CTRL 16 bit Packet Arbiter Ctrl Register */
+enum {
+ PA_CLR_TO_TX2 = 1<<13, /* Clear IRQ Packet Timeout TX2 */
+ PA_CLR_TO_TX1 = 1<<12, /* Clear IRQ Packet Timeout TX1 */
+ PA_CLR_TO_RX2 = 1<<11, /* Clear IRQ Packet Timeout RX2 */
+ PA_CLR_TO_RX1 = 1<<10, /* Clear IRQ Packet Timeout RX1 */
+ PA_ENA_TO_TX2 = 1<<9, /* Enable Timeout Timer TX2 */
+ PA_DIS_TO_TX2 = 1<<8, /* Disable Timeout Timer TX2 */
+ PA_ENA_TO_TX1 = 1<<7, /* Enable Timeout Timer TX1 */
+ PA_DIS_TO_TX1 = 1<<6, /* Disable Timeout Timer TX1 */
+ PA_ENA_TO_RX2 = 1<<5, /* Enable Timeout Timer RX2 */
+ PA_DIS_TO_RX2 = 1<<4, /* Disable Timeout Timer RX2 */
+ PA_ENA_TO_RX1 = 1<<3, /* Enable Timeout Timer RX1 */
+ PA_DIS_TO_RX1 = 1<<2, /* Disable Timeout Timer RX1 */
+ PA_RST_CLR = 1<<1, /* Clear MAC Arbiter Reset */
+ PA_RST_SET = 1<<0, /* Set MAC Arbiter Reset */
+};
+
+#define PA_ENA_TO_ALL (PA_ENA_TO_RX1 | PA_ENA_TO_RX2 |\
+ PA_ENA_TO_TX1 | PA_ENA_TO_TX2)
+
+
+/* Transmit Arbiter Registers MAC 1 and 2, use MR_ADDR() to access */
+/* TXA_ITI_INI 32 bit Tx Arb Interval Timer Init Val */
+/* TXA_ITI_VAL 32 bit Tx Arb Interval Timer Value */
+/* TXA_LIM_INI 32 bit Tx Arb Limit Counter Init Val */
+/* TXA_LIM_VAL 32 bit Tx Arb Limit Counter Value */
+
+#define TXA_MAX_VAL 0x00ffffffUL /* Bit 23.. 0: Max TXA Timer/Cnt Val */
+
+/* TXA_CTRL 8 bit Tx Arbiter Control Register */
+enum {
+ TXA_ENA_FSYNC = 1<<7, /* Enable force of sync Tx queue */
+ TXA_DIS_FSYNC = 1<<6, /* Disable force of sync Tx queue */
+ TXA_ENA_ALLOC = 1<<5, /* Enable alloc of free bandwidth */
+ TXA_DIS_ALLOC = 1<<4, /* Disable alloc of free bandwidth */
+ TXA_START_RC = 1<<3, /* Start sync Rate Control */
+ TXA_STOP_RC = 1<<2, /* Stop sync Rate Control */
+ TXA_ENA_ARB = 1<<1, /* Enable Tx Arbiter */
+ TXA_DIS_ARB = 1<<0, /* Disable Tx Arbiter */
+};
+
+/*
+ * Bank 4 - 5
+ */
+/* Transmit Arbiter Registers MAC 1 and 2, use MR_ADDR() to access */
+enum {
+ TXA_ITI_INI = 0x0200,/* 32 bit Tx Arb Interval Timer Init Val*/
+ TXA_ITI_VAL = 0x0204,/* 32 bit Tx Arb Interval Timer Value */
+ TXA_LIM_INI = 0x0208,/* 32 bit Tx Arb Limit Counter Init Val */
+ TXA_LIM_VAL = 0x020c,/* 32 bit Tx Arb Limit Counter Value */
+ TXA_CTRL = 0x0210,/* 8 bit Tx Arbiter Control Register */
+ TXA_TEST = 0x0211,/* 8 bit Tx Arbiter Test Register */
+ TXA_STAT = 0x0212,/* 8 bit Tx Arbiter Status Register */
+};
+
+
+enum {
+ B6_EXT_REG = 0x0300,/* External registers (GENESIS only) */
+ B7_CFG_SPC = 0x0380,/* copy of the Configuration register */
+ B8_RQ1_REGS = 0x0400,/* Receive Queue 1 */
+ B8_RQ2_REGS = 0x0480,/* Receive Queue 2 */
+ B8_TS1_REGS = 0x0600,/* Transmit sync queue 1 */
+ B8_TA1_REGS = 0x0680,/* Transmit async queue 1 */
+ B8_TS2_REGS = 0x0700,/* Transmit sync queue 2 */
+ B8_TA2_REGS = 0x0780,/* Transmit sync queue 2 */
+ B16_RAM_REGS = 0x0800,/* RAM Buffer Registers */
+};
+
+/* Queue Register Offsets, use Q_ADDR() to access */
+enum {
+ B8_Q_REGS = 0x0400, /* base of Queue registers */
+ Q_D = 0x00, /* 8*32 bit Current Descriptor */
+ Q_DA_L = 0x20, /* 32 bit Current Descriptor Address Low dWord */
+ Q_DA_H = 0x24, /* 32 bit Current Descriptor Address High dWord */
+ Q_AC_L = 0x28, /* 32 bit Current Address Counter Low dWord */
+ Q_AC_H = 0x2c, /* 32 bit Current Address Counter High dWord */
+ Q_BC = 0x30, /* 32 bit Current Byte Counter */
+ Q_CSR = 0x34, /* 32 bit BMU Control/Status Register */
+ Q_F = 0x38, /* 32 bit Flag Register */
+ Q_T1 = 0x3c, /* 32 bit Test Register 1 */
+ Q_T1_TR = 0x3c, /* 8 bit Test Register 1 Transfer SM */
+ Q_T1_WR = 0x3d, /* 8 bit Test Register 1 Write Descriptor SM */
+ Q_T1_RD = 0x3e, /* 8 bit Test Register 1 Read Descriptor SM */
+ Q_T1_SV = 0x3f, /* 8 bit Test Register 1 Supervisor SM */
+ Q_T2 = 0x40, /* 32 bit Test Register 2 */
+ Q_T3 = 0x44, /* 32 bit Test Register 3 */
+
+/* Yukon-2 */
+ Q_DONE = 0x24, /* 16 bit Done Index (Yukon-2 only) */
+ Q_WM = 0x40, /* 16 bit FIFO Watermark */
+ Q_AL = 0x42, /* 8 bit FIFO Alignment */
+ Q_RSP = 0x44, /* 16 bit FIFO Read Shadow Pointer */
+ Q_RSL = 0x46, /* 8 bit FIFO Read Shadow Level */
+ Q_RP = 0x48, /* 8 bit FIFO Read Pointer */
+ Q_RL = 0x4a, /* 8 bit FIFO Read Level */
+ Q_WP = 0x4c, /* 8 bit FIFO Write Pointer */
+ Q_WSP = 0x4d, /* 8 bit FIFO Write Shadow Pointer */
+ Q_WL = 0x4e, /* 8 bit FIFO Write Level */
+ Q_WSL = 0x4f, /* 8 bit FIFO Write Shadow Level */
+};
+#define Q_ADDR(reg, offs) (B8_Q_REGS + (reg) + (offs))
+
+/* RAM Buffer Register Offsets */
+enum {
+
+ RB_START = 0x00,/* 32 bit RAM Buffer Start Address */
+ RB_END = 0x04,/* 32 bit RAM Buffer End Address */
+ RB_WP = 0x08,/* 32 bit RAM Buffer Write Pointer */
+ RB_RP = 0x0c,/* 32 bit RAM Buffer Read Pointer */
+ RB_RX_UTPP = 0x10,/* 32 bit Rx Upper Threshold, Pause Packet */
+ RB_RX_LTPP = 0x14,/* 32 bit Rx Lower Threshold, Pause Packet */
+ RB_RX_UTHP = 0x18,/* 32 bit Rx Upper Threshold, High Prio */
+ RB_RX_LTHP = 0x1c,/* 32 bit Rx Lower Threshold, High Prio */
+ /* 0x10 - 0x1f: reserved at Tx RAM Buffer Registers */
+ RB_PC = 0x20,/* 32 bit RAM Buffer Packet Counter */
+ RB_LEV = 0x24,/* 32 bit RAM Buffer Level Register */
+ RB_CTRL = 0x28,/* 32 bit RAM Buffer Control Register */
+ RB_TST1 = 0x29,/* 8 bit RAM Buffer Test Register 1 */
+ RB_TST2 = 0x2a,/* 8 bit RAM Buffer Test Register 2 */
+};
+
+/* Receive and Transmit Queues */
+enum {
+ Q_R1 = 0x0000, /* Receive Queue 1 */
+ Q_R2 = 0x0080, /* Receive Queue 2 */
+ Q_XS1 = 0x0200, /* Synchronous Transmit Queue 1 */
+ Q_XA1 = 0x0280, /* Asynchronous Transmit Queue 1 */
+ Q_XS2 = 0x0300, /* Synchronous Transmit Queue 2 */
+ Q_XA2 = 0x0380, /* Asynchronous Transmit Queue 2 */
+};
+
+/* Different MAC Types */
+enum {
+ SK_MAC_XMAC = 0, /* Xaqti XMAC II */
+ SK_MAC_GMAC = 1, /* Marvell GMAC */
+};
+
+/* Different PHY Types */
+enum {
+ SK_PHY_XMAC = 0,/* integrated in XMAC II */
+ SK_PHY_BCOM = 1,/* Broadcom BCM5400 */
+ SK_PHY_LONE = 2,/* Level One LXT1000 [not supported]*/
+ SK_PHY_NAT = 3,/* National DP83891 [not supported] */
+ SK_PHY_MARV_COPPER= 4,/* Marvell 88E1011S */
+ SK_PHY_MARV_FIBER = 5,/* Marvell 88E1011S working on fiber */
+};
+
+/* PHY addresses (bits 12..8 of PHY address reg) */
+enum {
+ PHY_ADDR_XMAC = 0<<8,
+ PHY_ADDR_BCOM = 1<<8,
+ PHY_ADDR_LONE = 3<<8,
+ PHY_ADDR_NAT = 0<<8,
+/* GPHY address (bits 15..11 of SMI control reg) */
+ PHY_ADDR_MARV = 0,
+};
+
+#define RB_ADDR(offs, queue) (B16_RAM_REGS + (queue) + (offs))
+
+/* Receive MAC FIFO, Receive LED, and Link_Sync regs (GENESIS only) */
+enum {
+ RX_MFF_EA = 0x0c00,/* 32 bit Receive MAC FIFO End Address */
+ RX_MFF_WP = 0x0c04,/* 32 bit Receive MAC FIFO Write Pointer */
+
+ RX_MFF_RP = 0x0c0c,/* 32 bit Receive MAC FIFO Read Pointer */
+ RX_MFF_PC = 0x0c10,/* 32 bit Receive MAC FIFO Packet Cnt */
+ RX_MFF_LEV = 0x0c14,/* 32 bit Receive MAC FIFO Level */
+ RX_MFF_CTRL1 = 0x0c18,/* 16 bit Receive MAC FIFO Control Reg 1*/
+ RX_MFF_STAT_TO = 0x0c1a,/* 8 bit Receive MAC Status Timeout */
+ RX_MFF_TIST_TO = 0x0c1b,/* 8 bit Receive MAC Time Stamp Timeout */
+ RX_MFF_CTRL2 = 0x0c1c,/* 8 bit Receive MAC FIFO Control Reg 2*/
+ RX_MFF_TST1 = 0x0c1d,/* 8 bit Receive MAC FIFO Test Reg 1 */
+ RX_MFF_TST2 = 0x0c1e,/* 8 bit Receive MAC FIFO Test Reg 2 */
+
+ RX_LED_INI = 0x0c20,/* 32 bit Receive LED Cnt Init Value */
+ RX_LED_VAL = 0x0c24,/* 32 bit Receive LED Cnt Current Value */
+ RX_LED_CTRL = 0x0c28,/* 8 bit Receive LED Cnt Control Reg */
+ RX_LED_TST = 0x0c29,/* 8 bit Receive LED Cnt Test Register */
+
+ LNK_SYNC_INI = 0x0c30,/* 32 bit Link Sync Cnt Init Value */
+ LNK_SYNC_VAL = 0x0c34,/* 32 bit Link Sync Cnt Current Value */
+ LNK_SYNC_CTRL = 0x0c38,/* 8 bit Link Sync Cnt Control Register */
+ LNK_SYNC_TST = 0x0c39,/* 8 bit Link Sync Cnt Test Register */
+ LNK_LED_REG = 0x0c3c,/* 8 bit Link LED Register */
+};
+
+/* Receive and Transmit MAC FIFO Registers (GENESIS only) */
+/* RX_MFF_CTRL1 16 bit Receive MAC FIFO Control Reg 1 */
+enum {
+ MFF_ENA_RDY_PAT = 1<<13, /* Enable Ready Patch */
+ MFF_DIS_RDY_PAT = 1<<12, /* Disable Ready Patch */
+ MFF_ENA_TIM_PAT = 1<<11, /* Enable Timing Patch */
+ MFF_DIS_TIM_PAT = 1<<10, /* Disable Timing Patch */
+ MFF_ENA_ALM_FUL = 1<<9, /* Enable AlmostFull Sign */
+ MFF_DIS_ALM_FUL = 1<<8, /* Disable AlmostFull Sign */
+ MFF_ENA_PAUSE = 1<<7, /* Enable Pause Signaling */
+ MFF_DIS_PAUSE = 1<<6, /* Disable Pause Signaling */
+ MFF_ENA_FLUSH = 1<<5, /* Enable Frame Flushing */
+ MFF_DIS_FLUSH = 1<<4, /* Disable Frame Flushing */
+ MFF_ENA_TIST = 1<<3, /* Enable Time Stamp Gener */
+ MFF_DIS_TIST = 1<<2, /* Disable Time Stamp Gener */
+ MFF_CLR_INTIST = 1<<1, /* Clear IRQ No Time Stamp */
+ MFF_CLR_INSTAT = 1<<0, /* Clear IRQ No Status */
+#define MFF_RX_CTRL_DEF MFF_ENA_TIM_PAT
+};
+
+/* TX_MFF_CTRL1 16 bit Transmit MAC FIFO Control Reg 1 */
+enum {
+ MFF_CLR_PERR = 1<<15, /* Clear Parity Error IRQ */
+ /* Bit 14: reserved */
+ MFF_ENA_PKT_REC = 1<<13, /* Enable Packet Recovery */
+ MFF_DIS_PKT_REC = 1<<12, /* Disable Packet Recovery */
+
+ MFF_ENA_W4E = 1<<7, /* Enable Wait for Empty */
+ MFF_DIS_W4E = 1<<6, /* Disable Wait for Empty */
+
+ MFF_ENA_LOOPB = 1<<3, /* Enable Loopback */
+ MFF_DIS_LOOPB = 1<<2, /* Disable Loopback */
+ MFF_CLR_MAC_RST = 1<<1, /* Clear XMAC Reset */
+ MFF_SET_MAC_RST = 1<<0, /* Set XMAC Reset */
+};
+
+#define MFF_TX_CTRL_DEF (MFF_ENA_PKT_REC | MFF_ENA_TIM_PAT | MFF_ENA_FLUSH)
+
+/* RX_MFF_TST2 8 bit Receive MAC FIFO Test Register 2 */
+/* TX_MFF_TST2 8 bit Transmit MAC FIFO Test Register 2 */
+enum {
+ MFF_WSP_T_ON = 1<<6, /* Tx: Write Shadow Ptr TestOn */
+ MFF_WSP_T_OFF = 1<<5, /* Tx: Write Shadow Ptr TstOff */
+ MFF_WSP_INC = 1<<4, /* Tx: Write Shadow Ptr Increment */
+ MFF_PC_DEC = 1<<3, /* Packet Counter Decrement */
+ MFF_PC_T_ON = 1<<2, /* Packet Counter Test On */
+ MFF_PC_T_OFF = 1<<1, /* Packet Counter Test Off */
+ MFF_PC_INC = 1<<0, /* Packet Counter Increment */
+};
+
+/* RX_MFF_TST1 8 bit Receive MAC FIFO Test Register 1 */
+/* TX_MFF_TST1 8 bit Transmit MAC FIFO Test Register 1 */
+enum {
+ MFF_WP_T_ON = 1<<6, /* Write Pointer Test On */
+ MFF_WP_T_OFF = 1<<5, /* Write Pointer Test Off */
+ MFF_WP_INC = 1<<4, /* Write Pointer Increm */
+
+ MFF_RP_T_ON = 1<<2, /* Read Pointer Test On */
+ MFF_RP_T_OFF = 1<<1, /* Read Pointer Test Off */
+ MFF_RP_DEC = 1<<0, /* Read Pointer Decrement */
+};
+
+/* RX_MFF_CTRL2 8 bit Receive MAC FIFO Control Reg 2 */
+/* TX_MFF_CTRL2 8 bit Transmit MAC FIFO Control Reg 2 */
+enum {
+ MFF_ENA_OP_MD = 1<<3, /* Enable Operation Mode */
+ MFF_DIS_OP_MD = 1<<2, /* Disable Operation Mode */
+ MFF_RST_CLR = 1<<1, /* Clear MAC FIFO Reset */
+ MFF_RST_SET = 1<<0, /* Set MAC FIFO Reset */
+};
+
+
+/* Link LED Counter Registers (GENESIS only) */
+
+/* RX_LED_CTRL 8 bit Receive LED Cnt Control Reg */
+/* TX_LED_CTRL 8 bit Transmit LED Cnt Control Reg */
+/* LNK_SYNC_CTRL 8 bit Link Sync Cnt Control Register */
+enum {
+ LED_START = 1<<2, /* Start Timer */
+ LED_STOP = 1<<1, /* Stop Timer */
+ LED_STATE = 1<<0, /* Rx/Tx: LED State, 1=LED on */
+};
+
+/* RX_LED_TST 8 bit Receive LED Cnt Test Register */
+/* TX_LED_TST 8 bit Transmit LED Cnt Test Register */
+/* LNK_SYNC_TST 8 bit Link Sync Cnt Test Register */
+enum {
+ LED_T_ON = 1<<2, /* LED Counter Test mode On */
+ LED_T_OFF = 1<<1, /* LED Counter Test mode Off */
+ LED_T_STEP = 1<<0, /* LED Counter Step */
+};
+
+/* LNK_LED_REG 8 bit Link LED Register */
+enum {
+ LED_BLK_ON = 1<<5, /* Link LED Blinking On */
+ LED_BLK_OFF = 1<<4, /* Link LED Blinking Off */
+ LED_SYNC_ON = 1<<3, /* Use Sync Wire to switch LED */
+ LED_SYNC_OFF = 1<<2, /* Disable Sync Wire Input */
+ LED_ON = 1<<1, /* switch LED on */
+ LED_OFF = 1<<0, /* switch LED off */
+};
+
+/* Receive GMAC FIFO (YUKON and Yukon-2) */
+enum {
+ RX_GMF_EA = 0x0c40,/* 32 bit Rx GMAC FIFO End Address */
+ RX_GMF_AF_THR = 0x0c44,/* 32 bit Rx GMAC FIFO Almost Full Thresh. */
+ RX_GMF_CTRL_T = 0x0c48,/* 32 bit Rx GMAC FIFO Control/Test */
+ RX_GMF_FL_MSK = 0x0c4c,/* 32 bit Rx GMAC FIFO Flush Mask */
+ RX_GMF_FL_THR = 0x0c50,/* 32 bit Rx GMAC FIFO Flush Threshold */
+ RX_GMF_TR_THR = 0x0c54,/* 32 bit Rx Truncation Threshold (Yukon-2) */
+
+ RX_GMF_VLAN = 0x0c5c,/* 32 bit Rx VLAN Type Register (Yukon-2) */
+ RX_GMF_WP = 0x0c60,/* 32 bit Rx GMAC FIFO Write Pointer */
+
+ RX_GMF_WLEV = 0x0c68,/* 32 bit Rx GMAC FIFO Write Level */
+
+ RX_GMF_RP = 0x0c70,/* 32 bit Rx GMAC FIFO Read Pointer */
+
+ RX_GMF_RLEV = 0x0c78,/* 32 bit Rx GMAC FIFO Read Level */
+};
+
+
+/* TXA_TEST 8 bit Tx Arbiter Test Register */
+enum {
+ TXA_INT_T_ON = 1<<5, /* Tx Arb Interval Timer Test On */
+ TXA_INT_T_OFF = 1<<4, /* Tx Arb Interval Timer Test Off */
+ TXA_INT_T_STEP = 1<<3, /* Tx Arb Interval Timer Step */
+ TXA_LIM_T_ON = 1<<2, /* Tx Arb Limit Timer Test On */
+ TXA_LIM_T_OFF = 1<<1, /* Tx Arb Limit Timer Test Off */
+ TXA_LIM_T_STEP = 1<<0, /* Tx Arb Limit Timer Step */
+};
+
+/* TXA_STAT 8 bit Tx Arbiter Status Register */
+enum {
+ TXA_PRIO_XS = 1<<0, /* sync queue has prio to send */
+};
+
+
+/* Q_BC 32 bit Current Byte Counter */
+
+/* BMU Control Status Registers */
+/* B0_R1_CSR 32 bit BMU Ctrl/Stat Rx Queue 1 */
+/* B0_R2_CSR 32 bit BMU Ctrl/Stat Rx Queue 2 */
+/* B0_XA1_CSR 32 bit BMU Ctrl/Stat Sync Tx Queue 1 */
+/* B0_XS1_CSR 32 bit BMU Ctrl/Stat Async Tx Queue 1 */
+/* B0_XA2_CSR 32 bit BMU Ctrl/Stat Sync Tx Queue 2 */
+/* B0_XS2_CSR 32 bit BMU Ctrl/Stat Async Tx Queue 2 */
+/* Q_CSR 32 bit BMU Control/Status Register */
+
+enum {
+ CSR_SV_IDLE = 1<<24, /* BMU SM Idle */
+
+ CSR_DESC_CLR = 1<<21, /* Clear Reset for Descr */
+ CSR_DESC_SET = 1<<20, /* Set Reset for Descr */
+ CSR_FIFO_CLR = 1<<19, /* Clear Reset for FIFO */
+ CSR_FIFO_SET = 1<<18, /* Set Reset for FIFO */
+ CSR_HPI_RUN = 1<<17, /* Release HPI SM */
+ CSR_HPI_RST = 1<<16, /* Reset HPI SM to Idle */
+ CSR_SV_RUN = 1<<15, /* Release Supervisor SM */
+ CSR_SV_RST = 1<<14, /* Reset Supervisor SM */
+ CSR_DREAD_RUN = 1<<13, /* Release Descr Read SM */
+ CSR_DREAD_RST = 1<<12, /* Reset Descr Read SM */
+ CSR_DWRITE_RUN = 1<<11, /* Release Descr Write SM */
+ CSR_DWRITE_RST = 1<<10, /* Reset Descr Write SM */
+ CSR_TRANS_RUN = 1<<9, /* Release Transfer SM */
+ CSR_TRANS_RST = 1<<8, /* Reset Transfer SM */
+ CSR_ENA_POL = 1<<7, /* Enable Descr Polling */
+ CSR_DIS_POL = 1<<6, /* Disable Descr Polling */
+ CSR_STOP = 1<<5, /* Stop Rx/Tx Queue */
+ CSR_START = 1<<4, /* Start Rx/Tx Queue */
+ CSR_IRQ_CL_P = 1<<3, /* (Rx) Clear Parity IRQ */
+ CSR_IRQ_CL_B = 1<<2, /* Clear EOB IRQ */
+ CSR_IRQ_CL_F = 1<<1, /* Clear EOF IRQ */
+ CSR_IRQ_CL_C = 1<<0, /* Clear ERR IRQ */
+};
+
+#define CSR_SET_RESET (CSR_DESC_SET | CSR_FIFO_SET | CSR_HPI_RST |\
+ CSR_SV_RST | CSR_DREAD_RST | CSR_DWRITE_RST |\
+ CSR_TRANS_RST)
+#define CSR_CLR_RESET (CSR_DESC_CLR | CSR_FIFO_CLR | CSR_HPI_RUN |\
+ CSR_SV_RUN | CSR_DREAD_RUN | CSR_DWRITE_RUN |\
+ CSR_TRANS_RUN)
+
+/* Q_F 32 bit Flag Register */
+enum {
+ F_ALM_FULL = 1<<27, /* Rx FIFO: almost full */
+ F_EMPTY = 1<<27, /* Tx FIFO: empty flag */
+ F_FIFO_EOF = 1<<26, /* Tag (EOF Flag) bit in FIFO */
+ F_WM_REACHED = 1<<25, /* Watermark reached */
+
+ F_FIFO_LEVEL = 0x1fL<<16, /* Bit 23..16: # of Qwords in FIFO */
+ F_WATER_MARK = 0x0007ffL, /* Bit 10.. 0: Watermark */
+};
+
+/* RAM Buffer Register Offsets, use RB_ADDR(Queue, Offs) to access */
+/* RB_START 32 bit RAM Buffer Start Address */
+/* RB_END 32 bit RAM Buffer End Address */
+/* RB_WP 32 bit RAM Buffer Write Pointer */
+/* RB_RP 32 bit RAM Buffer Read Pointer */
+/* RB_RX_UTPP 32 bit Rx Upper Threshold, Pause Pack */
+/* RB_RX_LTPP 32 bit Rx Lower Threshold, Pause Pack */
+/* RB_RX_UTHP 32 bit Rx Upper Threshold, High Prio */
+/* RB_RX_LTHP 32 bit Rx Lower Threshold, High Prio */
+/* RB_PC 32 bit RAM Buffer Packet Counter */
+/* RB_LEV 32 bit RAM Buffer Level Register */
+
+#define RB_MSK 0x0007ffff /* Bit 18.. 0: RAM Buffer Pointer Bits */
+/* RB_TST2 8 bit RAM Buffer Test Register 2 */
+/* RB_TST1 8 bit RAM Buffer Test Register 1 */
+
+/* RB_CTRL 8 bit RAM Buffer Control Register */
+enum {
+ RB_ENA_STFWD = 1<<5, /* Enable Store & Forward */
+ RB_DIS_STFWD = 1<<4, /* Disable Store & Forward */
+ RB_ENA_OP_MD = 1<<3, /* Enable Operation Mode */
+ RB_DIS_OP_MD = 1<<2, /* Disable Operation Mode */
+ RB_RST_CLR = 1<<1, /* Clear RAM Buf STM Reset */
+ RB_RST_SET = 1<<0, /* Set RAM Buf STM Reset */
+};
+
+/* Transmit MAC FIFO and Transmit LED Registers (GENESIS only), */
+enum {
+ TX_MFF_EA = 0x0d00,/* 32 bit Transmit MAC FIFO End Address */
+ TX_MFF_WP = 0x0d04,/* 32 bit Transmit MAC FIFO WR Pointer */
+ TX_MFF_WSP = 0x0d08,/* 32 bit Transmit MAC FIFO WR Shadow Ptr */
+ TX_MFF_RP = 0x0d0c,/* 32 bit Transmit MAC FIFO RD Pointer */
+ TX_MFF_PC = 0x0d10,/* 32 bit Transmit MAC FIFO Packet Cnt */
+ TX_MFF_LEV = 0x0d14,/* 32 bit Transmit MAC FIFO Level */
+ TX_MFF_CTRL1 = 0x0d18,/* 16 bit Transmit MAC FIFO Ctrl Reg 1 */
+ TX_MFF_WAF = 0x0d1a,/* 8 bit Transmit MAC Wait after flush */
+
+ TX_MFF_CTRL2 = 0x0d1c,/* 8 bit Transmit MAC FIFO Ctrl Reg 2 */
+ TX_MFF_TST1 = 0x0d1d,/* 8 bit Transmit MAC FIFO Test Reg 1 */
+ TX_MFF_TST2 = 0x0d1e,/* 8 bit Transmit MAC FIFO Test Reg 2 */
+
+ TX_LED_INI = 0x0d20,/* 32 bit Transmit LED Cnt Init Value */
+ TX_LED_VAL = 0x0d24,/* 32 bit Transmit LED Cnt Current Val */
+ TX_LED_CTRL = 0x0d28,/* 8 bit Transmit LED Cnt Control Reg */
+ TX_LED_TST = 0x0d29,/* 8 bit Transmit LED Cnt Test Reg */
+};
+
+/* Counter and Timer constants, for a host clock of 62.5 MHz */
+#define SK_XMIT_DUR 0x002faf08UL /* 50 ms */
+#define SK_BLK_DUR 0x01dcd650UL /* 500 ms */
+
+#define SK_DPOLL_DEF 0x00ee6b28UL /* 250 ms at 62.5 MHz */
+
+#define SK_DPOLL_MAX 0x00ffffffUL /* 268 ms at 62.5 MHz */
+ /* 215 ms at 78.12 MHz */
+
+#define SK_FACT_62 100 /* is given in percent */
+#define SK_FACT_53 85 /* on GENESIS: 53.12 MHz */
+#define SK_FACT_78 125 /* on YUKON: 78.12 MHz */
+
+
+/* Transmit GMAC FIFO (YUKON only) */
+enum {
+ TX_GMF_EA = 0x0d40,/* 32 bit Tx GMAC FIFO End Address */
+ TX_GMF_AE_THR = 0x0d44,/* 32 bit Tx GMAC FIFO Almost Empty Thresh.*/
+ TX_GMF_CTRL_T = 0x0d48,/* 32 bit Tx GMAC FIFO Control/Test */
+
+ TX_GMF_WP = 0x0d60,/* 32 bit Tx GMAC FIFO Write Pointer */
+ TX_GMF_WSP = 0x0d64,/* 32 bit Tx GMAC FIFO Write Shadow Ptr. */
+ TX_GMF_WLEV = 0x0d68,/* 32 bit Tx GMAC FIFO Write Level */
+
+ TX_GMF_RP = 0x0d70,/* 32 bit Tx GMAC FIFO Read Pointer */
+ TX_GMF_RSTP = 0x0d74,/* 32 bit Tx GMAC FIFO Restart Pointer */
+ TX_GMF_RLEV = 0x0d78,/* 32 bit Tx GMAC FIFO Read Level */
+
+ /* Descriptor Poll Timer Registers */
+ B28_DPT_INI = 0x0e00,/* 24 bit Descriptor Poll Timer Init Val */
+ B28_DPT_VAL = 0x0e04,/* 24 bit Descriptor Poll Timer Curr Val */
+ B28_DPT_CTRL = 0x0e08,/* 8 bit Descriptor Poll Timer Ctrl Reg */
+
+ B28_DPT_TST = 0x0e0a,/* 8 bit Descriptor Poll Timer Test Reg */
+
+ /* Time Stamp Timer Registers (YUKON only) */
+ GMAC_TI_ST_VAL = 0x0e14,/* 32 bit Time Stamp Timer Curr Val */
+ GMAC_TI_ST_CTRL = 0x0e18,/* 8 bit Time Stamp Timer Ctrl Reg */
+ GMAC_TI_ST_TST = 0x0e1a,/* 8 bit Time Stamp Timer Test Reg */
+};
+
+/* Status BMU Registers (Yukon-2 only)*/
+enum {
+ STAT_CTRL = 0x0e80,/* 32 bit Status BMU Control Reg */
+ STAT_LAST_IDX = 0x0e84,/* 16 bit Status BMU Last Index */
+ /* 0x0e85 - 0x0e86: reserved */
+ STAT_LIST_ADDR_LO = 0x0e88,/* 32 bit Status List Start Addr (low) */
+ STAT_LIST_ADDR_HI = 0x0e8c,/* 32 bit Status List Start Addr (high) */
+ STAT_TXA1_RIDX = 0x0e90,/* 16 bit Status TxA1 Report Index Reg */
+ STAT_TXS1_RIDX = 0x0e92,/* 16 bit Status TxS1 Report Index Reg */
+ STAT_TXA2_RIDX = 0x0e94,/* 16 bit Status TxA2 Report Index Reg */
+ STAT_TXS2_RIDX = 0x0e96,/* 16 bit Status TxS2 Report Index Reg */
+ STAT_TX_IDX_TH = 0x0e98,/* 16 bit Status Tx Index Threshold Reg */
+ STAT_PUT_IDX = 0x0e9c,/* 16 bit Status Put Index Reg */
+
+/* FIFO Control/Status Registers (Yukon-2 only)*/
+ STAT_FIFO_WP = 0x0ea0,/* 8 bit Status FIFO Write Pointer Reg */
+ STAT_FIFO_RP = 0x0ea4,/* 8 bit Status FIFO Read Pointer Reg */
+ STAT_FIFO_RSP = 0x0ea6,/* 8 bit Status FIFO Read Shadow Ptr */
+ STAT_FIFO_LEVEL = 0x0ea8,/* 8 bit Status FIFO Level Reg */
+ STAT_FIFO_SHLVL = 0x0eaa,/* 8 bit Status FIFO Shadow Level Reg */
+ STAT_FIFO_WM = 0x0eac,/* 8 bit Status FIFO Watermark Reg */
+ STAT_FIFO_ISR_WM = 0x0ead,/* 8 bit Status FIFO ISR Watermark Reg */
+
+/* Level and ISR Timer Registers (Yukon-2 only)*/
+ STAT_LEV_TIMER_INI = 0x0eb0,/* 32 bit Level Timer Init. Value Reg */
+ STAT_LEV_TIMER_CNT = 0x0eb4,/* 32 bit Level Timer Counter Reg */
+ STAT_LEV_TIMER_CTRL = 0x0eb8,/* 8 bit Level Timer Control Reg */
+ STAT_LEV_TIMER_TEST = 0x0eb9,/* 8 bit Level Timer Test Reg */
+ STAT_TX_TIMER_INI = 0x0ec0,/* 32 bit Tx Timer Init. Value Reg */
+ STAT_TX_TIMER_CNT = 0x0ec4,/* 32 bit Tx Timer Counter Reg */
+ STAT_TX_TIMER_CTRL = 0x0ec8,/* 8 bit Tx Timer Control Reg */
+ STAT_TX_TIMER_TEST = 0x0ec9,/* 8 bit Tx Timer Test Reg */
+ STAT_ISR_TIMER_INI = 0x0ed0,/* 32 bit ISR Timer Init. Value Reg */
+ STAT_ISR_TIMER_CNT = 0x0ed4,/* 32 bit ISR Timer Counter Reg */
+ STAT_ISR_TIMER_CTRL = 0x0ed8,/* 8 bit ISR Timer Control Reg */
+ STAT_ISR_TIMER_TEST = 0x0ed9,/* 8 bit ISR Timer Test Reg */
+
+ ST_LAST_IDX_MASK = 0x007f,/* Last Index Mask */
+ ST_TXRP_IDX_MASK = 0x0fff,/* Tx Report Index Mask */
+ ST_TXTH_IDX_MASK = 0x0fff,/* Tx Threshold Index Mask */
+ ST_WM_IDX_MASK = 0x3f,/* FIFO Watermark Index Mask */
+};
+
+enum {
+ LINKLED_OFF = 0x01,
+ LINKLED_ON = 0x02,
+ LINKLED_LINKSYNC_OFF = 0x04,
+ LINKLED_LINKSYNC_ON = 0x08,
+ LINKLED_BLINK_OFF = 0x10,
+ LINKLED_BLINK_ON = 0x20,
+};
+
+/* GMAC and GPHY Control Registers (YUKON only) */
+enum {
+ GMAC_CTRL = 0x0f00,/* 32 bit GMAC Control Reg */
+ GPHY_CTRL = 0x0f04,/* 32 bit GPHY Control Reg */
+ GMAC_IRQ_SRC = 0x0f08,/* 8 bit GMAC Interrupt Source Reg */
+ GMAC_IRQ_MSK = 0x0f0c,/* 8 bit GMAC Interrupt Mask Reg */
+ GMAC_LINK_CTRL = 0x0f10,/* 16 bit Link Control Reg */
+
+/* Wake-up Frame Pattern Match Control Registers (YUKON only) */
+
+ WOL_REG_OFFS = 0x20,/* HW-Bug: Address is + 0x20 against spec. */
+
+ WOL_CTRL_STAT = 0x0f20,/* 16 bit WOL Control/Status Reg */
+ WOL_MATCH_CTL = 0x0f22,/* 8 bit WOL Match Control Reg */
+ WOL_MATCH_RES = 0x0f23,/* 8 bit WOL Match Result Reg */
+ WOL_MAC_ADDR = 0x0f24,/* 32 bit WOL MAC Address */
+ WOL_PATT_PME = 0x0f2a,/* 8 bit WOL PME Match Enable (Yukon-2) */
+ WOL_PATT_ASFM = 0x0f2b,/* 8 bit WOL ASF Match Enable (Yukon-2) */
+ WOL_PATT_RPTR = 0x0f2c,/* 8 bit WOL Pattern Read Pointer */
+
+/* WOL Pattern Length Registers (YUKON only) */
+
+ WOL_PATT_LEN_LO = 0x0f30,/* 32 bit WOL Pattern Length 3..0 */
+ WOL_PATT_LEN_HI = 0x0f34,/* 24 bit WOL Pattern Length 6..4 */
+
+/* WOL Pattern Counter Registers (YUKON only) */
+
+ WOL_PATT_CNT_0 = 0x0f38,/* 32 bit WOL Pattern Counter 3..0 */
+ WOL_PATT_CNT_4 = 0x0f3c,/* 24 bit WOL Pattern Counter 6..4 */
+};
+
+enum {
+ WOL_PATT_RAM_1 = 0x1000,/* WOL Pattern RAM Link 1 */
+ WOL_PATT_RAM_2 = 0x1400,/* WOL Pattern RAM Link 2 */
+};
+
+enum {
+ BASE_XMAC_1 = 0x2000,/* XMAC 1 registers */
+ BASE_GMAC_1 = 0x2800,/* GMAC 1 registers */
+ BASE_XMAC_2 = 0x3000,/* XMAC 2 registers */
+ BASE_GMAC_2 = 0x3800,/* GMAC 2 registers */
+};
+
+/*
+ * Receive Frame Status Encoding
+ */
+enum {
+ XMR_FS_LEN = 0x3fff<<18, /* Bit 31..18: Rx Frame Length */
+ XMR_FS_2L_VLAN = 1<<17, /* Bit 17: tagged wh 2Lev VLAN ID*/
+ XMR_FS_1_VLAN = 1<<16, /* Bit 16: tagged wh 1ev VLAN ID*/
+ XMR_FS_BC = 1<<15, /* Bit 15: Broadcast Frame */
+ XMR_FS_MC = 1<<14, /* Bit 14: Multicast Frame */
+ XMR_FS_UC = 1<<13, /* Bit 13: Unicast Frame */
+
+ XMR_FS_BURST = 1<<11, /* Bit 11: Burst Mode */
+ XMR_FS_CEX_ERR = 1<<10, /* Bit 10: Carrier Ext. Error */
+ XMR_FS_802_3 = 1<<9, /* Bit 9: 802.3 Frame */
+ XMR_FS_COL_ERR = 1<<8, /* Bit 8: Collision Error */
+ XMR_FS_CAR_ERR = 1<<7, /* Bit 7: Carrier Event Error */
+ XMR_FS_LEN_ERR = 1<<6, /* Bit 6: In-Range Length Error */
+ XMR_FS_FRA_ERR = 1<<5, /* Bit 5: Framing Error */
+ XMR_FS_RUNT = 1<<4, /* Bit 4: Runt Frame */
+ XMR_FS_LNG_ERR = 1<<3, /* Bit 3: Giant (Jumbo) Frame */
+ XMR_FS_FCS_ERR = 1<<2, /* Bit 2: Frame Check Sequ Err */
+ XMR_FS_ERR = 1<<1, /* Bit 1: Frame Error */
+ XMR_FS_MCTRL = 1<<0, /* Bit 0: MAC Control Packet */
+
+/*
+ * XMR_FS_ERR will be set if
+ * XMR_FS_FCS_ERR, XMR_FS_LNG_ERR, XMR_FS_RUNT,
+ * XMR_FS_FRA_ERR, XMR_FS_LEN_ERR, or XMR_FS_CEX_ERR
+ * is set. XMR_FS_LNG_ERR and XMR_FS_LEN_ERR will issue
+ * XMR_FS_ERR unless the corresponding bit in the Receive Command
+ * Register is set.
+ */
+};
+
+/*
+,* XMAC-PHY Registers, indirect addressed over the XMAC
+ */
+enum {
+ PHY_XMAC_CTRL = 0x00,/* 16 bit r/w PHY Control Register */
+ PHY_XMAC_STAT = 0x01,/* 16 bit r/w PHY Status Register */
+ PHY_XMAC_ID0 = 0x02,/* 16 bit r/o PHY ID0 Register */
+ PHY_XMAC_ID1 = 0x03,/* 16 bit r/o PHY ID1 Register */
+ PHY_XMAC_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
+ PHY_XMAC_AUNE_LP = 0x05,/* 16 bit r/o Link Partner Abi Reg */
+ PHY_XMAC_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
+ PHY_XMAC_NEPG = 0x07,/* 16 bit r/w Next Page Register */
+ PHY_XMAC_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner */
+
+ PHY_XMAC_EXT_STAT = 0x0f,/* 16 bit r/o Ext Status Register */
+ PHY_XMAC_RES_ABI = 0x10,/* 16 bit r/o PHY Resolved Ability */
+};
+/*
+ * Broadcom-PHY Registers, indirect addressed over XMAC
+ */
+enum {
+ PHY_BCOM_CTRL = 0x00,/* 16 bit r/w PHY Control Register */
+ PHY_BCOM_STAT = 0x01,/* 16 bit r/o PHY Status Register */
+ PHY_BCOM_ID0 = 0x02,/* 16 bit r/o PHY ID0 Register */
+ PHY_BCOM_ID1 = 0x03,/* 16 bit r/o PHY ID1 Register */
+ PHY_BCOM_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
+ PHY_BCOM_AUNE_LP = 0x05,/* 16 bit r/o Link Part Ability Reg */
+ PHY_BCOM_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
+ PHY_BCOM_NEPG = 0x07,/* 16 bit r/w Next Page Register */
+ PHY_BCOM_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner */
+ /* Broadcom-specific registers */
+ PHY_BCOM_1000T_CTRL = 0x09,/* 16 bit r/w 1000Base-T Control Reg */
+ PHY_BCOM_1000T_STAT = 0x0a,/* 16 bit r/o 1000Base-T Status Reg */
+ PHY_BCOM_EXT_STAT = 0x0f,/* 16 bit r/o Extended Status Reg */
+ PHY_BCOM_P_EXT_CTRL = 0x10,/* 16 bit r/w PHY Extended Ctrl Reg */
+ PHY_BCOM_P_EXT_STAT = 0x11,/* 16 bit r/o PHY Extended Stat Reg */
+ PHY_BCOM_RE_CTR = 0x12,/* 16 bit r/w Receive Error Counter */
+ PHY_BCOM_FC_CTR = 0x13,/* 16 bit r/w False Carrier Sense Cnt */
+ PHY_BCOM_RNO_CTR = 0x14,/* 16 bit r/w Receiver NOT_OK Cnt */
+
+ PHY_BCOM_AUX_CTRL = 0x18,/* 16 bit r/w Auxiliary Control Reg */
+ PHY_BCOM_AUX_STAT = 0x19,/* 16 bit r/o Auxiliary Stat Summary */
+ PHY_BCOM_INT_STAT = 0x1a,/* 16 bit r/o Interrupt Status Reg */
+ PHY_BCOM_INT_MASK = 0x1b,/* 16 bit r/w Interrupt Mask Reg */
+};
+
+/*
+ * Marvel-PHY Registers, indirect addressed over GMAC
+ */
+enum {
+ PHY_MARV_CTRL = 0x00,/* 16 bit r/w PHY Control Register */
+ PHY_MARV_STAT = 0x01,/* 16 bit r/o PHY Status Register */
+ PHY_MARV_ID0 = 0x02,/* 16 bit r/o PHY ID0 Register */
+ PHY_MARV_ID1 = 0x03,/* 16 bit r/o PHY ID1 Register */
+ PHY_MARV_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
+ PHY_MARV_AUNE_LP = 0x05,/* 16 bit r/o Link Part Ability Reg */
+ PHY_MARV_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
+ PHY_MARV_NEPG = 0x07,/* 16 bit r/w Next Page Register */
+ PHY_MARV_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner */
+ /* Marvel-specific registers */
+ PHY_MARV_1000T_CTRL = 0x09,/* 16 bit r/w 1000Base-T Control Reg */
+ PHY_MARV_1000T_STAT = 0x0a,/* 16 bit r/o 1000Base-T Status Reg */
+ PHY_MARV_EXT_STAT = 0x0f,/* 16 bit r/o Extended Status Reg */
+ PHY_MARV_PHY_CTRL = 0x10,/* 16 bit r/w PHY Specific Ctrl Reg */
+ PHY_MARV_PHY_STAT = 0x11,/* 16 bit r/o PHY Specific Stat Reg */
+ PHY_MARV_INT_MASK = 0x12,/* 16 bit r/w Interrupt Mask Reg */
+ PHY_MARV_INT_STAT = 0x13,/* 16 bit r/o Interrupt Status Reg */
+ PHY_MARV_EXT_CTRL = 0x14,/* 16 bit r/w Ext. PHY Specific Ctrl */
+ PHY_MARV_RXE_CNT = 0x15,/* 16 bit r/w Receive Error Counter */
+ PHY_MARV_EXT_ADR = 0x16,/* 16 bit r/w Ext. Ad. for Cable Diag. */
+ PHY_MARV_PORT_IRQ = 0x17,/* 16 bit r/o Port 0 IRQ (88E1111 only) */
+ PHY_MARV_LED_CTRL = 0x18,/* 16 bit r/w LED Control Reg */
+ PHY_MARV_LED_OVER = 0x19,/* 16 bit r/w Manual LED Override Reg */
+ PHY_MARV_EXT_CTRL_2 = 0x1a,/* 16 bit r/w Ext. PHY Specific Ctrl 2 */
+ PHY_MARV_EXT_P_STAT = 0x1b,/* 16 bit r/w Ext. PHY Spec. Stat Reg */
+ PHY_MARV_CABLE_DIAG = 0x1c,/* 16 bit r/o Cable Diagnostic Reg */
+ PHY_MARV_PAGE_ADDR = 0x1d,/* 16 bit r/w Extended Page Address Reg */
+ PHY_MARV_PAGE_DATA = 0x1e,/* 16 bit r/w Extended Page Data Reg */
+
+/* for 10/100 Fast Ethernet PHY (88E3082 only) */
+ PHY_MARV_FE_LED_PAR = 0x16,/* 16 bit r/w LED Parallel Select Reg. */
+ PHY_MARV_FE_LED_SER = 0x17,/* 16 bit r/w LED Stream Select S. LED */
+ PHY_MARV_FE_VCT_TX = 0x1a,/* 16 bit r/w VCT Reg. for TXP/N Pins */
+ PHY_MARV_FE_VCT_RX = 0x1b,/* 16 bit r/o VCT Reg. for RXP/N Pins */
+ PHY_MARV_FE_SPEC_2 = 0x1c,/* 16 bit r/w Specific Control Reg. 2 */
+};
+
+/* Level One-PHY Registers, indirect addressed over XMAC */
+enum {
+ PHY_LONE_CTRL = 0x00,/* 16 bit r/w PHY Control Register */
+ PHY_LONE_STAT = 0x01,/* 16 bit r/o PHY Status Register */
+ PHY_LONE_ID0 = 0x02,/* 16 bit r/o PHY ID0 Register */
+ PHY_LONE_ID1 = 0x03,/* 16 bit r/o PHY ID1 Register */
+ PHY_LONE_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
+ PHY_LONE_AUNE_LP = 0x05,/* 16 bit r/o Link Part Ability Reg */
+ PHY_LONE_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
+ PHY_LONE_NEPG = 0x07,/* 16 bit r/w Next Page Register */
+ PHY_LONE_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner */
+ /* Level One-specific registers */
+ PHY_LONE_1000T_CTRL = 0x09,/* 16 bit r/w 1000Base-T Control Reg */
+ PHY_LONE_1000T_STAT = 0x0a,/* 16 bit r/o 1000Base-T Status Reg */
+ PHY_LONE_EXT_STAT = 0x0f,/* 16 bit r/o Extended Status Reg */
+ PHY_LONE_PORT_CFG = 0x10,/* 16 bit r/w Port Configuration Reg*/
+ PHY_LONE_Q_STAT = 0x11,/* 16 bit r/o Quick Status Reg */
+ PHY_LONE_INT_ENAB = 0x12,/* 16 bit r/w Interrupt Enable Reg */
+ PHY_LONE_INT_STAT = 0x13,/* 16 bit r/o Interrupt Status Reg */
+ PHY_LONE_LED_CFG = 0x14,/* 16 bit r/w LED Configuration Reg */
+ PHY_LONE_PORT_CTRL = 0x15,/* 16 bit r/w Port Control Reg */
+ PHY_LONE_CIM = 0x16,/* 16 bit r/o CIM Reg */
+};
+
+/* National-PHY Registers, indirect addressed over XMAC */
+enum {
+ PHY_NAT_CTRL = 0x00,/* 16 bit r/w PHY Control Register */
+ PHY_NAT_STAT = 0x01,/* 16 bit r/w PHY Status Register */
+ PHY_NAT_ID0 = 0x02,/* 16 bit r/o PHY ID0 Register */
+ PHY_NAT_ID1 = 0x03,/* 16 bit r/o PHY ID1 Register */
+ PHY_NAT_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
+ PHY_NAT_AUNE_LP = 0x05,/* 16 bit r/o Link Partner Ability Reg */
+ PHY_NAT_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
+ PHY_NAT_NEPG = 0x07,/* 16 bit r/w Next Page Register */
+ PHY_NAT_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner Reg */
+ /* National-specific registers */
+ PHY_NAT_1000T_CTRL = 0x09,/* 16 bit r/w 1000Base-T Control Reg */
+ PHY_NAT_1000T_STAT = 0x0a,/* 16 bit r/o 1000Base-T Status Reg */
+ PHY_NAT_EXT_STAT = 0x0f,/* 16 bit r/o Extended Status Register */
+ PHY_NAT_EXT_CTRL1 = 0x10,/* 16 bit r/o Extended Control Reg1 */
+ PHY_NAT_Q_STAT1 = 0x11,/* 16 bit r/o Quick Status Reg1 */
+ PHY_NAT_10B_OP = 0x12,/* 16 bit r/o 10Base-T Operations Reg */
+ PHY_NAT_EXT_CTRL2 = 0x13,/* 16 bit r/o Extended Control Reg1 */
+ PHY_NAT_Q_STAT2 = 0x14,/* 16 bit r/o Quick Status Reg2 */
+
+ PHY_NAT_PHY_ADDR = 0x19,/* 16 bit r/o PHY Address Register */
+};
+
+enum {
+ PHY_CT_RESET = 1<<15, /* Bit 15: (sc) clear all PHY related regs */
+ PHY_CT_LOOP = 1<<14, /* Bit 14: enable Loopback over PHY */
+ PHY_CT_SPS_LSB = 1<<13, /* Bit 13: Speed select, lower bit */
+ PHY_CT_ANE = 1<<12, /* Bit 12: Auto-Negotiation Enabled */
+ PHY_CT_PDOWN = 1<<11, /* Bit 11: Power Down Mode */
+ PHY_CT_ISOL = 1<<10, /* Bit 10: Isolate Mode */
+ PHY_CT_RE_CFG = 1<<9, /* Bit 9: (sc) Restart Auto-Negotiation */
+ PHY_CT_DUP_MD = 1<<8, /* Bit 8: Duplex Mode */
+ PHY_CT_COL_TST = 1<<7, /* Bit 7: Collision Test enabled */
+ PHY_CT_SPS_MSB = 1<<6, /* Bit 6: Speed select, upper bit */
+};
+
+enum {
+ PHY_CT_SP1000 = PHY_CT_SPS_MSB, /* enable speed of 1000 Mbps */
+ PHY_CT_SP100 = PHY_CT_SPS_LSB, /* enable speed of 100 Mbps */
+ PHY_CT_SP10 = 0, /* enable speed of 10 Mbps */
+};
+
+enum {
+ PHY_ST_EXT_ST = 1<<8, /* Bit 8: Extended Status Present */
+
+ PHY_ST_PRE_SUP = 1<<6, /* Bit 6: Preamble Suppression */
+ PHY_ST_AN_OVER = 1<<5, /* Bit 5: Auto-Negotiation Over */
+ PHY_ST_REM_FLT = 1<<4, /* Bit 4: Remote Fault Condition Occured */
+ PHY_ST_AN_CAP = 1<<3, /* Bit 3: Auto-Negotiation Capability */
+ PHY_ST_LSYNC = 1<<2, /* Bit 2: Link Synchronized */
+ PHY_ST_JAB_DET = 1<<1, /* Bit 1: Jabber Detected */
+ PHY_ST_EXT_REG = 1<<0, /* Bit 0: Extended Register available */
+};
+
+enum {
+ PHY_I1_OUI_MSK = 0x3f<<10, /* Bit 15..10: Organization Unique ID */
+ PHY_I1_MOD_NUM = 0x3f<<4, /* Bit 9.. 4: Model Number */
+ PHY_I1_REV_MSK = 0xf, /* Bit 3.. 0: Revision Number */
+};
+
+/* different Broadcom PHY Ids */
+enum {
+ PHY_BCOM_ID1_A1 = 0x6041,
+ PHY_BCOM_ID1_B2 = 0x6043,
+ PHY_BCOM_ID1_C0 = 0x6044,
+ PHY_BCOM_ID1_C5 = 0x6047,
+};
+
+/* different Marvell PHY Ids */
+enum {
+ PHY_MARV_ID0_VAL= 0x0141, /* Marvell Unique Identifier */
+ PHY_MARV_ID1_B0 = 0x0C23, /* Yukon (PHY 88E1011) */
+ PHY_MARV_ID1_B2 = 0x0C25, /* Yukon-Plus (PHY 88E1011) */
+ PHY_MARV_ID1_C2 = 0x0CC2, /* Yukon-EC (PHY 88E1111) */
+ PHY_MARV_ID1_Y2 = 0x0C91, /* Yukon-2 (PHY 88E1112) */
+};
+
+enum {
+ PHY_AN_NXT_PG = 1<<15, /* Bit 15: Request Next Page */
+ PHY_X_AN_ACK = 1<<14, /* Bit 14: (ro) Acknowledge Received */
+ PHY_X_AN_RFB = 3<<12,/* Bit 13..12: Remote Fault Bits */
+
+ PHY_X_AN_PAUSE = 3<<7,/* Bit 8.. 7: Pause Bits */
+ PHY_X_AN_HD = 1<<6, /* Bit 6: Half Duplex */
+ PHY_X_AN_FD = 1<<5, /* Bit 5: Full Duplex */
+};
+
+enum {
+ PHY_B_AN_RF = 1<<13, /* Bit 13: Remote Fault */
+
+ PHY_B_AN_ASP = 1<<11, /* Bit 11: Asymmetric Pause */
+ PHY_B_AN_PC = 1<<10, /* Bit 10: Pause Capable */
+ PHY_B_AN_SEL = 0x1f, /* Bit 4..0: Selector Field, 00001=Ethernet*/
+};
+
+enum {
+ PHY_L_AN_RF = 1<<13, /* Bit 13: Remote Fault */
+ /* Bit 12: reserved */
+ PHY_L_AN_ASP = 1<<11, /* Bit 11: Asymmetric Pause */
+ PHY_L_AN_PC = 1<<10, /* Bit 10: Pause Capable */
+
+ PHY_L_AN_SEL = 0x1f, /* Bit 4..0: Selector Field, 00001=Ethernet*/
+};
+
+/* PHY_NAT_AUNE_ADV 16 bit r/w Auto-Negotiation Advertisement */
+/* PHY_NAT_AUNE_LP 16 bit r/o Link Partner Ability Reg *****/
+/* PHY_AN_NXT_PG (see XMAC) Bit 15: Request Next Page */
+enum {
+ PHY_N_AN_RF = 1<<13, /* Bit 13: Remote Fault */
+
+ PHY_N_AN_100F = 1<<11, /* Bit 11: 100Base-T2 FD Support */
+ PHY_N_AN_100H = 1<<10, /* Bit 10: 100Base-T2 HD Support */
+
+ PHY_N_AN_SEL = 0x1f, /* Bit 4..0: Selector Field, 00001=Ethernet*/
+};
+
+/* field type definition for PHY_x_AN_SEL */
+enum {
+ PHY_SEL_TYPE = 1, /* 00001 = Ethernet */
+};
+
+enum {
+ PHY_ANE_LP_NP = 1<<3, /* Bit 3: Link Partner can Next Page */
+ PHY_ANE_LOC_NP = 1<<2, /* Bit 2: Local PHY can Next Page */
+ PHY_ANE_RX_PG = 1<<1, /* Bit 1: Page Received */
+};
+
+enum {
+ PHY_ANE_PAR_DF = 1<<4, /* Bit 4: Parallel Detection Fault */
+
+ PHY_ANE_LP_CAP = 1<<0, /* Bit 0: Link Partner Auto-Neg. Cap. */
+};
+
+enum {
+ PHY_NP_MORE = 1<<15, /* Bit 15: More, Next Pages to follow */
+ PHY_NP_ACK1 = 1<<14, /* Bit 14: (ro) Ack1, for receiving a message */
+ PHY_NP_MSG_VAL = 1<<13, /* Bit 13: Message Page valid */
+ PHY_NP_ACK2 = 1<<12, /* Bit 12: Ack2, comply with msg content */
+ PHY_NP_TOG = 1<<11, /* Bit 11: Toggle Bit, ensure sync */
+ PHY_NP_MSG = 0x07ff, /* Bit 10..0: Message from/to Link Partner */
+};
+
+enum {
+ PHY_X_EX_FD = 1<<15, /* Bit 15: Device Supports Full Duplex */
+ PHY_X_EX_HD = 1<<14, /* Bit 14: Device Supports Half Duplex */
+};
+
+enum {
+ PHY_X_RS_PAUSE = 3<<7,/* Bit 8..7: selected Pause Mode */
+ PHY_X_RS_HD = 1<<6, /* Bit 6: Half Duplex Mode selected */
+ PHY_X_RS_FD = 1<<5, /* Bit 5: Full Duplex Mode selected */
+ PHY_X_RS_ABLMIS = 1<<4, /* Bit 4: duplex or pause cap mismatch */
+ PHY_X_RS_PAUMIS = 1<<3, /* Bit 3: pause capability mismatch */
+};
+
+/** Remote Fault Bits (PHY_X_AN_RFB) encoding */
+enum {
+ X_RFB_OK = 0<<12,/* Bit 13..12 No errors, Link OK */
+ X_RFB_LF = 1<<12, /* Bit 13..12 Link Failure */
+ X_RFB_OFF = 2<<12,/* Bit 13..12 Offline */
+ X_RFB_AN_ERR = 3<<12,/* Bit 13..12 Auto-Negotiation Error */
+};
+
+/* Pause Bits (PHY_X_AN_PAUSE and PHY_X_RS_PAUSE) encoding */
+enum {
+ PHY_X_P_NO_PAUSE = 0<<7,/* Bit 8..7: no Pause Mode */
+ PHY_X_P_SYM_MD = 1<<7, /* Bit 8..7: symmetric Pause Mode */
+ PHY_X_P_ASYM_MD = 2<<7,/* Bit 8..7: asymmetric Pause Mode */
+ PHY_X_P_BOTH_MD = 3<<7,/* Bit 8..7: both Pause Mode */
+};
+
+
+/* Broadcom-Specific */
+/***** PHY_BCOM_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
+enum {
+ PHY_B_1000C_TEST = 7<<13,/* Bit 15..13: Test Modes */
+ PHY_B_1000C_MSE = 1<<12, /* Bit 12: Master/Slave Enable */
+ PHY_B_1000C_MSC = 1<<11, /* Bit 11: M/S Configuration */
+ PHY_B_1000C_RD = 1<<10, /* Bit 10: Repeater/DTE */
+ PHY_B_1000C_AFD = 1<<9, /* Bit 9: Advertise Full Duplex */
+ PHY_B_1000C_AHD = 1<<8, /* Bit 8: Advertise Half Duplex */
+};
+
+/***** PHY_BCOM_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
+/***** PHY_MARV_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
+enum {
+ PHY_B_1000S_MSF = 1<<15, /* Bit 15: Master/Slave Fault */
+ PHY_B_1000S_MSR = 1<<14, /* Bit 14: Master/Slave Result */
+ PHY_B_1000S_LRS = 1<<13, /* Bit 13: Local Receiver Status */
+ PHY_B_1000S_RRS = 1<<12, /* Bit 12: Remote Receiver Status */
+ PHY_B_1000S_LP_FD = 1<<11, /* Bit 11: Link Partner can FD */
+ PHY_B_1000S_LP_HD = 1<<10, /* Bit 10: Link Partner can HD */
+ /* Bit 9..8: reserved */
+ PHY_B_1000S_IEC = 0xff, /* Bit 7..0: Idle Error Count */
+};
+
+/***** PHY_BCOM_EXT_STAT 16 bit r/o Extended Status Register *****/
+enum {
+ PHY_B_ES_X_FD_CAP = 1<<15, /* Bit 15: 1000Base-X FD capable */
+ PHY_B_ES_X_HD_CAP = 1<<14, /* Bit 14: 1000Base-X HD capable */
+ PHY_B_ES_T_FD_CAP = 1<<13, /* Bit 13: 1000Base-T FD capable */
+ PHY_B_ES_T_HD_CAP = 1<<12, /* Bit 12: 1000Base-T HD capable */
+};
+
+/***** PHY_BCOM_P_EXT_CTRL 16 bit r/w PHY Extended Control Reg *****/
+enum {
+ PHY_B_PEC_MAC_PHY = 1<<15, /* Bit 15: 10BIT/GMI-Interface */
+ PHY_B_PEC_DIS_CROSS = 1<<14, /* Bit 14: Disable MDI Crossover */
+ PHY_B_PEC_TX_DIS = 1<<13, /* Bit 13: Tx output Disabled */
+ PHY_B_PEC_INT_DIS = 1<<12, /* Bit 12: Interrupts Disabled */
+ PHY_B_PEC_F_INT = 1<<11, /* Bit 11: Force Interrupt */
+ PHY_B_PEC_BY_45 = 1<<10, /* Bit 10: Bypass 4B5B-Decoder */
+ PHY_B_PEC_BY_SCR = 1<<9, /* Bit 9: Bypass Scrambler */
+ PHY_B_PEC_BY_MLT3 = 1<<8, /* Bit 8: Bypass MLT3 Encoder */
+ PHY_B_PEC_BY_RXA = 1<<7, /* Bit 7: Bypass Rx Alignm. */
+ PHY_B_PEC_RES_SCR = 1<<6, /* Bit 6: Reset Scrambler */
+ PHY_B_PEC_EN_LTR = 1<<5, /* Bit 5: Ena LED Traffic Mode */
+ PHY_B_PEC_LED_ON = 1<<4, /* Bit 4: Force LED's on */
+ PHY_B_PEC_LED_OFF = 1<<3, /* Bit 3: Force LED's off */
+ PHY_B_PEC_EX_IPG = 1<<2, /* Bit 2: Extend Tx IPG Mode */
+ PHY_B_PEC_3_LED = 1<<1, /* Bit 1: Three Link LED mode */
+ PHY_B_PEC_HIGH_LA = 1<<0, /* Bit 0: GMII FIFO Elasticy */
+};
+
+/***** PHY_BCOM_P_EXT_STAT 16 bit r/o PHY Extended Status Reg *****/
+enum {
+ PHY_B_PES_CROSS_STAT = 1<<13, /* Bit 13: MDI Crossover Status */
+ PHY_B_PES_INT_STAT = 1<<12, /* Bit 12: Interrupt Status */
+ PHY_B_PES_RRS = 1<<11, /* Bit 11: Remote Receiver Stat. */
+ PHY_B_PES_LRS = 1<<10, /* Bit 10: Local Receiver Stat. */
+ PHY_B_PES_LOCKED = 1<<9, /* Bit 9: Locked */
+ PHY_B_PES_LS = 1<<8, /* Bit 8: Link Status */
+ PHY_B_PES_RF = 1<<7, /* Bit 7: Remote Fault */
+ PHY_B_PES_CE_ER = 1<<6, /* Bit 6: Carrier Ext Error */
+ PHY_B_PES_BAD_SSD = 1<<5, /* Bit 5: Bad SSD */
+ PHY_B_PES_BAD_ESD = 1<<4, /* Bit 4: Bad ESD */
+ PHY_B_PES_RX_ER = 1<<3, /* Bit 3: Receive Error */
+ PHY_B_PES_TX_ER = 1<<2, /* Bit 2: Transmit Error */
+ PHY_B_PES_LOCK_ER = 1<<1, /* Bit 1: Lock Error */
+ PHY_B_PES_MLT3_ER = 1<<0, /* Bit 0: MLT3 code Error */
+};
+
+/***** PHY_BCOM_FC_CTR 16 bit r/w False Carrier Counter *****/
+enum {
+ PHY_B_FC_CTR = 0xff, /* Bit 7..0: False Carrier Counter */
+
+/***** PHY_BCOM_RNO_CTR 16 bit r/w Receive NOT_OK Counter *****/
+ PHY_B_RC_LOC_MSK = 0xff00, /* Bit 15..8: Local Rx NOT_OK cnt */
+ PHY_B_RC_REM_MSK = 0x00ff, /* Bit 7..0: Remote Rx NOT_OK cnt */
+
+/***** PHY_BCOM_AUX_CTRL 16 bit r/w Auxiliary Control Reg *****/
+ PHY_B_AC_L_SQE = 1<<15, /* Bit 15: Low Squelch */
+ PHY_B_AC_LONG_PACK = 1<<14, /* Bit 14: Rx Long Packets */
+ PHY_B_AC_ER_CTRL = 3<<12,/* Bit 13..12: Edgerate Control */
+ /* Bit 11: reserved */
+ PHY_B_AC_TX_TST = 1<<10, /* Bit 10: Tx test bit, always 1 */
+ /* Bit 9.. 8: reserved */
+ PHY_B_AC_DIS_PRF = 1<<7, /* Bit 7: dis part resp filter */
+ /* Bit 6: reserved */
+ PHY_B_AC_DIS_PM = 1<<5, /* Bit 5: dis power management */
+ /* Bit 4: reserved */
+ PHY_B_AC_DIAG = 1<<3, /* Bit 3: Diagnostic Mode */
+};
+
+/***** PHY_BCOM_AUX_STAT 16 bit r/o Auxiliary Status Reg *****/
+enum {
+ PHY_B_AS_AN_C = 1<<15, /* Bit 15: AutoNeg complete */
+ PHY_B_AS_AN_CA = 1<<14, /* Bit 14: AN Complete Ack */
+ PHY_B_AS_ANACK_D = 1<<13, /* Bit 13: AN Ack Detect */
+ PHY_B_AS_ANAB_D = 1<<12, /* Bit 12: AN Ability Detect */
+ PHY_B_AS_NPW = 1<<11, /* Bit 11: AN Next Page Wait */
+ PHY_B_AS_AN_RES_MSK = 7<<8,/* Bit 10..8: AN HDC */
+ PHY_B_AS_PDF = 1<<7, /* Bit 7: Parallel Detect. Fault */
+ PHY_B_AS_RF = 1<<6, /* Bit 6: Remote Fault */
+ PHY_B_AS_ANP_R = 1<<5, /* Bit 5: AN Page Received */
+ PHY_B_AS_LP_ANAB = 1<<4, /* Bit 4: LP AN Ability */
+ PHY_B_AS_LP_NPAB = 1<<3, /* Bit 3: LP Next Page Ability */
+ PHY_B_AS_LS = 1<<2, /* Bit 2: Link Status */
+ PHY_B_AS_PRR = 1<<1, /* Bit 1: Pause Resolution-Rx */
+ PHY_B_AS_PRT = 1<<0, /* Bit 0: Pause Resolution-Tx */
+};
+#define PHY_B_AS_PAUSE_MSK (PHY_B_AS_PRR | PHY_B_AS_PRT)
+
+/***** PHY_BCOM_INT_STAT 16 bit r/o Interrupt Status Reg *****/
+/***** PHY_BCOM_INT_MASK 16 bit r/w Interrupt Mask Reg *****/
+enum {
+ PHY_B_IS_PSE = 1<<14, /* Bit 14: Pair Swap Error */
+ PHY_B_IS_MDXI_SC = 1<<13, /* Bit 13: MDIX Status Change */
+ PHY_B_IS_HCT = 1<<12, /* Bit 12: counter above 32k */
+ PHY_B_IS_LCT = 1<<11, /* Bit 11: counter above 128 */
+ PHY_B_IS_AN_PR = 1<<10, /* Bit 10: Page Received */
+ PHY_B_IS_NO_HDCL = 1<<9, /* Bit 9: No HCD Link */
+ PHY_B_IS_NO_HDC = 1<<8, /* Bit 8: No HCD */
+ PHY_B_IS_NEG_USHDC = 1<<7, /* Bit 7: Negotiated Unsup. HCD */
+ PHY_B_IS_SCR_S_ER = 1<<6, /* Bit 6: Scrambler Sync Error */
+ PHY_B_IS_RRS_CHANGE = 1<<5, /* Bit 5: Remote Rx Stat Change */
+ PHY_B_IS_LRS_CHANGE = 1<<4, /* Bit 4: Local Rx Stat Change */
+ PHY_B_IS_DUP_CHANGE = 1<<3, /* Bit 3: Duplex Mode Change */
+ PHY_B_IS_LSP_CHANGE = 1<<2, /* Bit 2: Link Speed Change */
+ PHY_B_IS_LST_CHANGE = 1<<1, /* Bit 1: Link Status Changed */
+ PHY_B_IS_CRC_ER = 1<<0, /* Bit 0: CRC Error */
+};
+#define PHY_B_DEF_MSK (~(PHY_B_IS_AN_PR | PHY_B_IS_LST_CHANGE))
+
+/* Pause Bits (PHY_B_AN_ASP and PHY_B_AN_PC) encoding */
+enum {
+ PHY_B_P_NO_PAUSE = 0<<10,/* Bit 11..10: no Pause Mode */
+ PHY_B_P_SYM_MD = 1<<10, /* Bit 11..10: symmetric Pause Mode */
+ PHY_B_P_ASYM_MD = 2<<10,/* Bit 11..10: asymmetric Pause Mode */
+ PHY_B_P_BOTH_MD = 3<<10,/* Bit 11..10: both Pause Mode */
+};
+/*
+ * Resolved Duplex mode and Capabilities (Aux Status Summary Reg)
+ */
+enum {
+ PHY_B_RES_1000FD = 7<<8,/* Bit 10..8: 1000Base-T Full Dup. */
+ PHY_B_RES_1000HD = 6<<8,/* Bit 10..8: 1000Base-T Half Dup. */
+};
+
+/*
+ * Level One-Specific
+ */
+/***** PHY_LONE_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
+enum {
+ PHY_L_1000C_TEST = 7<<13,/* Bit 15..13: Test Modes */
+ PHY_L_1000C_MSE = 1<<12, /* Bit 12: Master/Slave Enable */
+ PHY_L_1000C_MSC = 1<<11, /* Bit 11: M/S Configuration */
+ PHY_L_1000C_RD = 1<<10, /* Bit 10: Repeater/DTE */
+ PHY_L_1000C_AFD = 1<<9, /* Bit 9: Advertise Full Duplex */
+ PHY_L_1000C_AHD = 1<<8, /* Bit 8: Advertise Half Duplex */
+};
+
+/***** PHY_LONE_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
+enum {
+ PHY_L_1000S_MSF = 1<<15, /* Bit 15: Master/Slave Fault */
+ PHY_L_1000S_MSR = 1<<14, /* Bit 14: Master/Slave Result */
+ PHY_L_1000S_LRS = 1<<13, /* Bit 13: Local Receiver Status */
+ PHY_L_1000S_RRS = 1<<12, /* Bit 12: Remote Receiver Status */
+ PHY_L_1000S_LP_FD = 1<<11, /* Bit 11: Link Partner can FD */
+ PHY_L_1000S_LP_HD = 1<<10, /* Bit 10: Link Partner can HD */
+
+ PHY_L_1000S_IEC = 0xff, /* Bit 7..0: Idle Error Count */
+
+/***** PHY_LONE_EXT_STAT 16 bit r/o Extended Status Register *****/
+ PHY_L_ES_X_FD_CAP = 1<<15, /* Bit 15: 1000Base-X FD capable */
+ PHY_L_ES_X_HD_CAP = 1<<14, /* Bit 14: 1000Base-X HD capable */
+ PHY_L_ES_T_FD_CAP = 1<<13, /* Bit 13: 1000Base-T FD capable */
+ PHY_L_ES_T_HD_CAP = 1<<12, /* Bit 12: 1000Base-T HD capable */
+};
+
+/***** PHY_LONE_PORT_CFG 16 bit r/w Port Configuration Reg *****/
+enum {
+ PHY_L_PC_REP_MODE = 1<<15, /* Bit 15: Repeater Mode */
+
+ PHY_L_PC_TX_DIS = 1<<13, /* Bit 13: Tx output Disabled */
+ PHY_L_PC_BY_SCR = 1<<12, /* Bit 12: Bypass Scrambler */
+ PHY_L_PC_BY_45 = 1<<11, /* Bit 11: Bypass 4B5B-Decoder */
+ PHY_L_PC_JAB_DIS = 1<<10, /* Bit 10: Jabber Disabled */
+ PHY_L_PC_SQE = 1<<9, /* Bit 9: Enable Heartbeat */
+ PHY_L_PC_TP_LOOP = 1<<8, /* Bit 8: TP Loopback */
+ PHY_L_PC_SSS = 1<<7, /* Bit 7: Smart Speed Selection */
+ PHY_L_PC_FIFO_SIZE = 1<<6, /* Bit 6: FIFO Size */
+ PHY_L_PC_PRE_EN = 1<<5, /* Bit 5: Preamble Enable */
+ PHY_L_PC_CIM = 1<<4, /* Bit 4: Carrier Integrity Mon */
+ PHY_L_PC_10_SER = 1<<3, /* Bit 3: Use Serial Output */
+ PHY_L_PC_ANISOL = 1<<2, /* Bit 2: Unisolate Port */
+ PHY_L_PC_TEN_BIT = 1<<1, /* Bit 1: 10bit iface mode on */
+ PHY_L_PC_ALTCLOCK = 1<<0, /* Bit 0: (ro) ALTCLOCK Mode on */
+};
+
+/***** PHY_LONE_Q_STAT 16 bit r/o Quick Status Reg *****/
+enum {
+ PHY_L_QS_D_RATE = 3<<14,/* Bit 15..14: Data Rate */
+ PHY_L_QS_TX_STAT = 1<<13, /* Bit 13: Transmitting */
+ PHY_L_QS_RX_STAT = 1<<12, /* Bit 12: Receiving */
+ PHY_L_QS_COL_STAT = 1<<11, /* Bit 11: Collision */
+ PHY_L_QS_L_STAT = 1<<10, /* Bit 10: Link is up */
+ PHY_L_QS_DUP_MOD = 1<<9, /* Bit 9: Full/Half Duplex */
+ PHY_L_QS_AN = 1<<8, /* Bit 8: AutoNeg is On */
+ PHY_L_QS_AN_C = 1<<7, /* Bit 7: AN is Complete */
+ PHY_L_QS_LLE = 7<<4,/* Bit 6..4: Line Length Estim. */
+ PHY_L_QS_PAUSE = 1<<3, /* Bit 3: LP advertised Pause */
+ PHY_L_QS_AS_PAUSE = 1<<2, /* Bit 2: LP adv. asym. Pause */
+ PHY_L_QS_ISOLATE = 1<<1, /* Bit 1: CIM Isolated */
+ PHY_L_QS_EVENT = 1<<0, /* Bit 0: Event has occurred */
+};
+
+/***** PHY_LONE_INT_ENAB 16 bit r/w Interrupt Enable Reg *****/
+/***** PHY_LONE_INT_STAT 16 bit r/o Interrupt Status Reg *****/
+enum {
+ PHY_L_IS_AN_F = 1<<13, /* Bit 13: Auto-Negotiation fault */
+ PHY_L_IS_CROSS = 1<<11, /* Bit 11: Crossover used */
+ PHY_L_IS_POL = 1<<10, /* Bit 10: Polarity correct. used */
+ PHY_L_IS_SS = 1<<9, /* Bit 9: Smart Speed Downgrade */
+ PHY_L_IS_CFULL = 1<<8, /* Bit 8: Counter Full */
+ PHY_L_IS_AN_C = 1<<7, /* Bit 7: AutoNeg Complete */
+ PHY_L_IS_SPEED = 1<<6, /* Bit 6: Speed Changed */
+ PHY_L_IS_DUP = 1<<5, /* Bit 5: Duplex Changed */
+ PHY_L_IS_LS = 1<<4, /* Bit 4: Link Status Changed */
+ PHY_L_IS_ISOL = 1<<3, /* Bit 3: Isolate Occured */
+ PHY_L_IS_MDINT = 1<<2, /* Bit 2: (ro) STAT: MII Int Pending */
+ PHY_L_IS_INTEN = 1<<1, /* Bit 1: ENAB: Enable IRQs */
+ PHY_L_IS_FORCE = 1<<0, /* Bit 0: ENAB: Force Interrupt */
+};
+
+/* int. mask */
+#define PHY_L_DEF_MSK (PHY_L_IS_LS | PHY_L_IS_ISOL | PHY_L_IS_INTEN)
+
+/***** PHY_LONE_LED_CFG 16 bit r/w LED Configuration Reg *****/
+enum {
+ PHY_L_LC_LEDC = 3<<14,/* Bit 15..14: Col/Blink/On/Off */
+ PHY_L_LC_LEDR = 3<<12,/* Bit 13..12: Rx/Blink/On/Off */
+ PHY_L_LC_LEDT = 3<<10,/* Bit 11..10: Tx/Blink/On/Off */
+ PHY_L_LC_LEDG = 3<<8,/* Bit 9..8: Giga/Blink/On/Off */
+ PHY_L_LC_LEDS = 3<<6,/* Bit 7..6: 10-100/Blink/On/Off */
+ PHY_L_LC_LEDL = 3<<4,/* Bit 5..4: Link/Blink/On/Off */
+ PHY_L_LC_LEDF = 3<<2,/* Bit 3..2: Duplex/Blink/On/Off */
+ PHY_L_LC_PSTRECH= 1<<1, /* Bit 1: Strech LED Pulses */
+ PHY_L_LC_FREQ = 1<<0, /* Bit 0: 30/100 ms */
+};
+
+/***** PHY_LONE_PORT_CTRL 16 bit r/w Port Control Reg *****/
+enum {
+ PHY_L_PC_TX_TCLK = 1<<15, /* Bit 15: Enable TX_TCLK */
+ PHY_L_PC_ALT_NP = 1<<13, /* Bit 14: Alternate Next Page */
+ PHY_L_PC_GMII_ALT= 1<<12, /* Bit 13: Alternate GMII driver */
+ PHY_L_PC_TEN_CRS = 1<<10, /* Bit 10: Extend CRS*/
+};
+
+/***** PHY_LONE_CIM 16 bit r/o CIM Reg *****/
+enum {
+ PHY_L_CIM_ISOL = 0xff<<8,/* Bit 15..8: Isolate Count */
+ PHY_L_CIM_FALSE_CAR = 0xff, /* Bit 7..0: False Carrier Count */
+};
+
+/*
+ * Pause Bits (PHY_L_AN_ASP and PHY_L_AN_PC) encoding
+ */
+enum {
+ PHY_L_P_NO_PAUSE= 0<<10,/* Bit 11..10: no Pause Mode */
+ PHY_L_P_SYM_MD = 1<<10, /* Bit 11..10: symmetric Pause Mode */
+ PHY_L_P_ASYM_MD = 2<<10,/* Bit 11..10: asymmetric Pause Mode */
+ PHY_L_P_BOTH_MD = 3<<10,/* Bit 11..10: both Pause Mode */
+};
+
+/*
+ * National-Specific
+ */
+/***** PHY_NAT_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
+enum {
+ PHY_N_1000C_TEST= 7<<13,/* Bit 15..13: Test Modes */
+ PHY_N_1000C_MSE = 1<<12, /* Bit 12: Master/Slave Enable */
+ PHY_N_1000C_MSC = 1<<11, /* Bit 11: M/S Configuration */
+ PHY_N_1000C_RD = 1<<10, /* Bit 10: Repeater/DTE */
+ PHY_N_1000C_AFD = 1<<9, /* Bit 9: Advertise Full Duplex */
+ PHY_N_1000C_AHD = 1<<8, /* Bit 8: Advertise Half Duplex */
+ PHY_N_1000C_APC = 1<<7, /* Bit 7: Asymmetric Pause Cap. */};
+
+
+/***** PHY_NAT_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
+enum {
+ PHY_N_1000S_MSF = 1<<15, /* Bit 15: Master/Slave Fault */
+ PHY_N_1000S_MSR = 1<<14, /* Bit 14: Master/Slave Result */
+ PHY_N_1000S_LRS = 1<<13, /* Bit 13: Local Receiver Status */
+ PHY_N_1000S_RRS = 1<<12, /* Bit 12: Remote Receiver Status*/
+ PHY_N_1000S_LP_FD= 1<<11, /* Bit 11: Link Partner can FD */
+ PHY_N_1000S_LP_HD= 1<<10, /* Bit 10: Link Partner can HD */
+ PHY_N_1000C_LP_APC= 1<<9, /* Bit 9: LP Asym. Pause Cap. */
+ PHY_N_1000S_IEC = 0xff, /* Bit 7..0: Idle Error Count */
+};
+
+/***** PHY_NAT_EXT_STAT 16 bit r/o Extended Status Register *****/
+enum {
+ PHY_N_ES_X_FD_CAP= 1<<15, /* Bit 15: 1000Base-X FD capable */
+ PHY_N_ES_X_HD_CAP= 1<<14, /* Bit 14: 1000Base-X HD capable */
+ PHY_N_ES_T_FD_CAP= 1<<13, /* Bit 13: 1000Base-T FD capable */
+ PHY_N_ES_T_HD_CAP= 1<<12, /* Bit 12: 1000Base-T HD capable */
+};
+
+/** Marvell-Specific */
+enum {
+ PHY_M_AN_NXT_PG = 1<<15, /* Request Next Page */
+ PHY_M_AN_ACK = 1<<14, /* (ro) Acknowledge Received */
+ PHY_M_AN_RF = 1<<13, /* Remote Fault */
+
+ PHY_M_AN_ASP = 1<<11, /* Asymmetric Pause */
+ PHY_M_AN_PC = 1<<10, /* MAC Pause implemented */
+ PHY_M_AN_100_T4 = 1<<9, /* Not cap. 100Base-T4 (always 0) */
+ PHY_M_AN_100_FD = 1<<8, /* Advertise 100Base-TX Full Duplex */
+ PHY_M_AN_100_HD = 1<<7, /* Advertise 100Base-TX Half Duplex */
+ PHY_M_AN_10_FD = 1<<6, /* Advertise 10Base-TX Full Duplex */
+ PHY_M_AN_10_HD = 1<<5, /* Advertise 10Base-TX Half Duplex */
+ PHY_M_AN_SEL_MSK =0x1f<<4, /* Bit 4.. 0: Selector Field Mask */
+};
+
+/* special defines for FIBER (88E1011S only) */
+enum {
+ PHY_M_AN_ASP_X = 1<<8, /* Asymmetric Pause */
+ PHY_M_AN_PC_X = 1<<7, /* MAC Pause implemented */
+ PHY_M_AN_1000X_AHD = 1<<6, /* Advertise 10000Base-X Half Duplex */
+ PHY_M_AN_1000X_AFD = 1<<5, /* Advertise 10000Base-X Full Duplex */
+};
+
+/* Pause Bits (PHY_M_AN_ASP_X and PHY_M_AN_PC_X) encoding */
+enum {
+ PHY_M_P_NO_PAUSE_X = 0<<7,/* Bit 8.. 7: no Pause Mode */
+ PHY_M_P_SYM_MD_X = 1<<7, /* Bit 8.. 7: symmetric Pause Mode */
+ PHY_M_P_ASYM_MD_X = 2<<7,/* Bit 8.. 7: asymmetric Pause Mode */
+ PHY_M_P_BOTH_MD_X = 3<<7,/* Bit 8.. 7: both Pause Mode */
+};
+
+/***** PHY_MARV_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
+enum {
+ PHY_M_1000C_TEST = 7<<13,/* Bit 15..13: Test Modes */
+ PHY_M_1000C_MSE = 1<<12, /* Manual Master/Slave Enable */
+ PHY_M_1000C_MSC = 1<<11, /* M/S Configuration (1=Master) */
+ PHY_M_1000C_MPD = 1<<10, /* Multi-Port Device */
+ PHY_M_1000C_AFD = 1<<9, /* Advertise Full Duplex */
+ PHY_M_1000C_AHD = 1<<8, /* Advertise Half Duplex */
+};
+
+/***** PHY_MARV_PHY_CTRL 16 bit r/w PHY Specific Ctrl Reg *****/
+enum {
+ PHY_M_PC_TX_FFD_MSK = 3<<14,/* Bit 15..14: Tx FIFO Depth Mask */
+ PHY_M_PC_RX_FFD_MSK = 3<<12,/* Bit 13..12: Rx FIFO Depth Mask */
+ PHY_M_PC_ASS_CRS_TX = 1<<11, /* Assert CRS on Transmit */
+ PHY_M_PC_FL_GOOD = 1<<10, /* Force Link Good */
+ PHY_M_PC_EN_DET_MSK = 3<<8,/* Bit 9.. 8: Energy Detect Mask */
+ PHY_M_PC_ENA_EXT_D = 1<<7, /* Enable Ext. Distance (10BT) */
+ PHY_M_PC_MDIX_MSK = 3<<5,/* Bit 6.. 5: MDI/MDIX Config. Mask */
+ PHY_M_PC_DIS_125CLK = 1<<4, /* Disable 125 CLK */
+ PHY_M_PC_MAC_POW_UP = 1<<3, /* MAC Power up */
+ PHY_M_PC_SQE_T_ENA = 1<<2, /* SQE Test Enabled */
+ PHY_M_PC_POL_R_DIS = 1<<1, /* Polarity Reversal Disabled */
+ PHY_M_PC_DIS_JABBER = 1<<0, /* Disable Jabber */
+};
+
+enum {
+ PHY_M_PC_EN_DET = 2<<8, /* Energy Detect (Mode 1) */
+ PHY_M_PC_EN_DET_PLUS = 3<<8, /* Energy Detect Plus (Mode 2) */
+};
+
+#define PHY_M_PC_MDI_XMODE(x) (((x)<<5) & PHY_M_PC_MDIX_MSK)
+
+enum {
+ PHY_M_PC_MAN_MDI = 0, /* 00 = Manual MDI configuration */
+ PHY_M_PC_MAN_MDIX = 1, /* 01 = Manual MDIX configuration */
+ PHY_M_PC_ENA_AUTO = 3, /* 11 = Enable Automatic Crossover */
+};
+
+/* for 10/100 Fast Ethernet PHY (88E3082 only) */
+enum {
+ PHY_M_PC_ENA_DTE_DT = 1<<15, /* Enable Data Terminal Equ. (DTE) Detect */
+ PHY_M_PC_ENA_ENE_DT = 1<<14, /* Enable Energy Detect (sense & pulse) */
+ PHY_M_PC_DIS_NLP_CK = 1<<13, /* Disable Normal Link Puls (NLP) Check */
+ PHY_M_PC_ENA_LIP_NP = 1<<12, /* Enable Link Partner Next Page Reg. */
+ PHY_M_PC_DIS_NLP_GN = 1<<11, /* Disable Normal Link Puls Generation */
+
+ PHY_M_PC_DIS_SCRAMB = 1<<9, /* Disable Scrambler */
+ PHY_M_PC_DIS_FEFI = 1<<8, /* Disable Far End Fault Indic. (FEFI) */
+
+ PHY_M_PC_SH_TP_SEL = 1<<6, /* Shielded Twisted Pair Select */
+ PHY_M_PC_RX_FD_MSK = 3<<2,/* Bit 3.. 2: Rx FIFO Depth Mask */
+};
+
+/***** PHY_MARV_PHY_STAT 16 bit r/o PHY Specific Status Reg *****/
+enum {
+ PHY_M_PS_SPEED_MSK = 3<<14, /* Bit 15..14: Speed Mask */
+ PHY_M_PS_SPEED_1000 = 1<<15, /* 10 = 1000 Mbps */
+ PHY_M_PS_SPEED_100 = 1<<14, /* 01 = 100 Mbps */
+ PHY_M_PS_SPEED_10 = 0, /* 00 = 10 Mbps */
+ PHY_M_PS_FULL_DUP = 1<<13, /* Full Duplex */
+ PHY_M_PS_PAGE_REC = 1<<12, /* Page Received */
+ PHY_M_PS_SPDUP_RES = 1<<11, /* Speed & Duplex Resolved */
+ PHY_M_PS_LINK_UP = 1<<10, /* Link Up */
+ PHY_M_PS_CABLE_MSK = 7<<7, /* Bit 9.. 7: Cable Length Mask */
+ PHY_M_PS_MDI_X_STAT = 1<<6, /* MDI Crossover Stat (1=MDIX) */
+ PHY_M_PS_DOWNS_STAT = 1<<5, /* Downshift Status (1=downsh.) */
+ PHY_M_PS_ENDET_STAT = 1<<4, /* Energy Detect Status (1=act) */
+ PHY_M_PS_TX_P_EN = 1<<3, /* Tx Pause Enabled */
+ PHY_M_PS_RX_P_EN = 1<<2, /* Rx Pause Enabled */
+ PHY_M_PS_POL_REV = 1<<1, /* Polarity Reversed */
+ PHY_M_PS_JABBER = 1<<0, /* Jabber */
+};
+
+#define PHY_M_PS_PAUSE_MSK (PHY_M_PS_TX_P_EN | PHY_M_PS_RX_P_EN)
+
+/* for 10/100 Fast Ethernet PHY (88E3082 only) */
+enum {
+ PHY_M_PS_DTE_DETECT = 1<<15, /* Data Terminal Equipment (DTE) Detected */
+ PHY_M_PS_RES_SPEED = 1<<14, /* Resolved Speed (1=100 Mbps, 0=10 Mbps */
+};
+
+enum {
+ PHY_M_IS_AN_ERROR = 1<<15, /* Auto-Negotiation Error */
+ PHY_M_IS_LSP_CHANGE = 1<<14, /* Link Speed Changed */
+ PHY_M_IS_DUP_CHANGE = 1<<13, /* Duplex Mode Changed */
+ PHY_M_IS_AN_PR = 1<<12, /* Page Received */
+ PHY_M_IS_AN_COMPL = 1<<11, /* Auto-Negotiation Completed */
+ PHY_M_IS_LST_CHANGE = 1<<10, /* Link Status Changed */
+ PHY_M_IS_SYMB_ERROR = 1<<9, /* Symbol Error */
+ PHY_M_IS_FALSE_CARR = 1<<8, /* False Carrier */
+ PHY_M_IS_FIFO_ERROR = 1<<7, /* FIFO Overflow/Underrun Error */
+ PHY_M_IS_MDI_CHANGE = 1<<6, /* MDI Crossover Changed */
+ PHY_M_IS_DOWNSH_DET = 1<<5, /* Downshift Detected */
+ PHY_M_IS_END_CHANGE = 1<<4, /* Energy Detect Changed */
+
+ PHY_M_IS_DTE_CHANGE = 1<<2, /* DTE Power Det. Status Changed */
+ PHY_M_IS_POL_CHANGE = 1<<1, /* Polarity Changed */
+ PHY_M_IS_JABBER = 1<<0, /* Jabber */
+};
+
+#define PHY_M_DEF_MSK ( PHY_M_IS_AN_ERROR | PHY_M_IS_LSP_CHANGE | \
+ PHY_M_IS_LST_CHANGE | PHY_M_IS_FIFO_ERROR)
+
+/***** PHY_MARV_EXT_CTRL 16 bit r/w Ext. PHY Specific Ctrl *****/
+enum {
+ PHY_M_EC_ENA_BC_EXT = 1<<15, /* Enable Block Carr. Ext. (88E1111 only) */
+ PHY_M_EC_ENA_LIN_LB = 1<<14, /* Enable Line Loopback (88E1111 only) */
+
+ PHY_M_EC_DIS_LINK_P = 1<<12, /* Disable Link Pulses (88E1111 only) */
+ PHY_M_EC_M_DSC_MSK = 3<<10, /* Bit 11..10: Master Downshift Counter */
+ /* (88E1011 only) */
+ PHY_M_EC_S_DSC_MSK = 3<<8,/* Bit 9.. 8: Slave Downshift Counter */
+ /* (88E1011 only) */
+ PHY_M_EC_M_DSC_MSK2 = 7<<9,/* Bit 11.. 9: Master Downshift Counter */
+ /* (88E1111 only) */
+ PHY_M_EC_DOWN_S_ENA = 1<<8, /* Downshift Enable (88E1111 only) */
+ /* !!! Errata in spec. (1 = disable) */
+ PHY_M_EC_RX_TIM_CT = 1<<7, /* RGMII Rx Timing Control*/
+ PHY_M_EC_MAC_S_MSK = 7<<4,/* Bit 6.. 4: Def. MAC interface speed */
+ PHY_M_EC_FIB_AN_ENA = 1<<3, /* Fiber Auto-Neg. Enable (88E1011S only) */
+ PHY_M_EC_DTE_D_ENA = 1<<2, /* DTE Detect Enable (88E1111 only) */
+ PHY_M_EC_TX_TIM_CT = 1<<1, /* RGMII Tx Timing Control */
+ PHY_M_EC_TRANS_DIS = 1<<0, /* Transmitter Disable (88E1111 only) */};
+
+#define PHY_M_EC_M_DSC(x) ((x)<<10) /* 00=1x; 01=2x; 10=3x; 11=4x */
+#define PHY_M_EC_S_DSC(x) ((x)<<8) /* 00=dis; 01=1x; 10=2x; 11=3x */
+#define PHY_M_EC_MAC_S(x) ((x)<<4) /* 01X=0; 110=2.5; 111=25 (MHz) */
+
+#define PHY_M_EC_M_DSC_2(x) ((x)<<9) /* 000=1x; 001=2x; 010=3x; 011=4x */
+ /* 100=5x; 101=6x; 110=7x; 111=8x */
+enum {
+ MAC_TX_CLK_0_MHZ = 2,
+ MAC_TX_CLK_2_5_MHZ = 6,
+ MAC_TX_CLK_25_MHZ = 7,
+};
+
+/***** PHY_MARV_LED_CTRL 16 bit r/w LED Control Reg *****/
+enum {
+ PHY_M_LEDC_DIS_LED = 1<<15, /* Disable LED */
+ PHY_M_LEDC_PULS_MSK = 7<<12,/* Bit 14..12: Pulse Stretch Mask */
+ PHY_M_LEDC_F_INT = 1<<11, /* Force Interrupt */
+ PHY_M_LEDC_BL_R_MSK = 7<<8,/* Bit 10.. 8: Blink Rate Mask */
+ PHY_M_LEDC_DP_C_LSB = 1<<7, /* Duplex Control (LSB, 88E1111 only) */
+ PHY_M_LEDC_TX_C_LSB = 1<<6, /* Tx Control (LSB, 88E1111 only) */
+ PHY_M_LEDC_LK_C_MSK = 7<<3,/* Bit 5.. 3: Link Control Mask */
+ /* (88E1111 only) */
+};
+
+enum {
+ PHY_M_LEDC_LINK_MSK = 3<<3,/* Bit 4.. 3: Link Control Mask */
+ /* (88E1011 only) */
+ PHY_M_LEDC_DP_CTRL = 1<<2, /* Duplex Control */
+ PHY_M_LEDC_DP_C_MSB = 1<<2, /* Duplex Control (MSB, 88E1111 only) */
+ PHY_M_LEDC_RX_CTRL = 1<<1, /* Rx Activity / Link */
+ PHY_M_LEDC_TX_CTRL = 1<<0, /* Tx Activity / Link */
+ PHY_M_LEDC_TX_C_MSB = 1<<0, /* Tx Control (MSB, 88E1111 only) */
+};
+
+#define PHY_M_LED_PULS_DUR(x) ( ((x)<<12) & PHY_M_LEDC_PULS_MSK)
+
+enum {
+ PULS_NO_STR = 0,/* no pulse stretching */
+ PULS_21MS = 1,/* 21 ms to 42 ms */
+ PULS_42MS = 2,/* 42 ms to 84 ms */
+ PULS_84MS = 3,/* 84 ms to 170 ms */
+ PULS_170MS = 4,/* 170 ms to 340 ms */
+ PULS_340MS = 5,/* 340 ms to 670 ms */
+ PULS_670MS = 6,/* 670 ms to 1.3 s */
+ PULS_1300MS = 7,/* 1.3 s to 2.7 s */
+};
+
+#define PHY_M_LED_BLINK_RT(x) ( ((x)<<8) & PHY_M_LEDC_BL_R_MSK)
+
+enum {
+ BLINK_42MS = 0,/* 42 ms */
+ BLINK_84MS = 1,/* 84 ms */
+ BLINK_170MS = 2,/* 170 ms */
+ BLINK_340MS = 3,/* 340 ms */
+ BLINK_670MS = 4,/* 670 ms */
+};
+
+/***** PHY_MARV_LED_OVER 16 bit r/w Manual LED Override Reg *****/
+#define PHY_M_LED_MO_SGMII(x) ((x)<<14) /* Bit 15..14: SGMII AN Timer */
+ /* Bit 13..12: reserved */
+#define PHY_M_LED_MO_DUP(x) ((x)<<10) /* Bit 11..10: Duplex */
+#define PHY_M_LED_MO_10(x) ((x)<<8) /* Bit 9.. 8: Link 10 */
+#define PHY_M_LED_MO_100(x) ((x)<<6) /* Bit 7.. 6: Link 100 */
+#define PHY_M_LED_MO_1000(x) ((x)<<4) /* Bit 5.. 4: Link 1000 */
+#define PHY_M_LED_MO_RX(x) ((x)<<2) /* Bit 3.. 2: Rx */
+#define PHY_M_LED_MO_TX(x) ((x)<<0) /* Bit 1.. 0: Tx */
+
+enum {
+ MO_LED_NORM = 0,
+ MO_LED_BLINK = 1,
+ MO_LED_OFF = 2,
+ MO_LED_ON = 3,
+};
+
+/***** PHY_MARV_EXT_CTRL_2 16 bit r/w Ext. PHY Specific Ctrl 2 *****/
+enum {
+ PHY_M_EC2_FI_IMPED = 1<<6, /* Fiber Input Impedance */
+ PHY_M_EC2_FO_IMPED = 1<<5, /* Fiber Output Impedance */
+ PHY_M_EC2_FO_M_CLK = 1<<4, /* Fiber Mode Clock Enable */
+ PHY_M_EC2_FO_BOOST = 1<<3, /* Fiber Output Boost */
+ PHY_M_EC2_FO_AM_MSK = 7,/* Bit 2.. 0: Fiber Output Amplitude */
+};
+
+/***** PHY_MARV_EXT_P_STAT 16 bit r/w Ext. PHY Specific Status *****/
+enum {
+ PHY_M_FC_AUTO_SEL = 1<<15, /* Fiber/Copper Auto Sel. Dis. */
+ PHY_M_FC_AN_REG_ACC = 1<<14, /* Fiber/Copper AN Reg. Access */
+ PHY_M_FC_RESOLUTION = 1<<13, /* Fiber/Copper Resolution */
+ PHY_M_SER_IF_AN_BP = 1<<12, /* Ser. IF AN Bypass Enable */
+ PHY_M_SER_IF_BP_ST = 1<<11, /* Ser. IF AN Bypass Status */
+ PHY_M_IRQ_POLARITY = 1<<10, /* IRQ polarity */
+ PHY_M_DIS_AUT_MED = 1<<9, /* Disable Aut. Medium Reg. Selection */
+ /* (88E1111 only) */
+ /* Bit 9.. 4: reserved (88E1011 only) */
+ PHY_M_UNDOC1 = 1<<7, /* undocumented bit !! */
+ PHY_M_DTE_POW_STAT = 1<<4, /* DTE Power Status (88E1111 only) */
+ PHY_M_MODE_MASK = 0xf, /* Bit 3.. 0: copy of HWCFG MODE[3:0] */
+};
+
+/***** PHY_MARV_CABLE_DIAG 16 bit r/o Cable Diagnostic Reg *****/
+enum {
+ PHY_M_CABD_ENA_TEST = 1<<15, /* Enable Test (Page 0) */
+ PHY_M_CABD_DIS_WAIT = 1<<15, /* Disable Waiting Period (Page 1) */
+ /* (88E1111 only) */
+ PHY_M_CABD_STAT_MSK = 3<<13, /* Bit 14..13: Status Mask */
+ PHY_M_CABD_AMPL_MSK = 0x1f<<8,/* Bit 12.. 8: Amplitude Mask */
+ /* (88E1111 only) */
+ PHY_M_CABD_DIST_MSK = 0xff, /* Bit 7.. 0: Distance Mask */
+};
+
+/* values for Cable Diagnostic Status (11=fail; 00=OK; 10=open; 01=short) */
+enum {
+ CABD_STAT_NORMAL= 0,
+ CABD_STAT_SHORT = 1,
+ CABD_STAT_OPEN = 2,
+ CABD_STAT_FAIL = 3,
+};
+
+/* for 10/100 Fast Ethernet PHY (88E3082 only) */
+/***** PHY_MARV_FE_LED_PAR 16 bit r/w LED Parallel Select Reg. *****/
+ /* Bit 15..12: reserved (used internally) */
+enum {
+ PHY_M_FELP_LED2_MSK = 0xf<<8, /* Bit 11.. 8: LED2 Mask (LINK) */
+ PHY_M_FELP_LED1_MSK = 0xf<<4, /* Bit 7.. 4: LED1 Mask (ACT) */
+ PHY_M_FELP_LED0_MSK = 0xf, /* Bit 3.. 0: LED0 Mask (SPEED) */
+};
+
+#define PHY_M_FELP_LED2_CTRL(x) ( ((x)<<8) & PHY_M_FELP_LED2_MSK)
+#define PHY_M_FELP_LED1_CTRL(x) ( ((x)<<4) & PHY_M_FELP_LED1_MSK)
+#define PHY_M_FELP_LED0_CTRL(x) ( ((x)<<0) & PHY_M_FELP_LED0_MSK)
+
+enum {
+ LED_PAR_CTRL_COLX = 0x00,
+ LED_PAR_CTRL_ERROR = 0x01,
+ LED_PAR_CTRL_DUPLEX = 0x02,
+ LED_PAR_CTRL_DP_COL = 0x03,
+ LED_PAR_CTRL_SPEED = 0x04,
+ LED_PAR_CTRL_LINK = 0x05,
+ LED_PAR_CTRL_TX = 0x06,
+ LED_PAR_CTRL_RX = 0x07,
+ LED_PAR_CTRL_ACT = 0x08,
+ LED_PAR_CTRL_LNK_RX = 0x09,
+ LED_PAR_CTRL_LNK_AC = 0x0a,
+ LED_PAR_CTRL_ACT_BL = 0x0b,
+ LED_PAR_CTRL_TX_BL = 0x0c,
+ LED_PAR_CTRL_RX_BL = 0x0d,
+ LED_PAR_CTRL_COL_BL = 0x0e,
+ LED_PAR_CTRL_INACT = 0x0f
+};
+
+/*****,PHY_MARV_FE_SPEC_2 16 bit r/w Specific Control Reg. 2 *****/
+enum {
+ PHY_M_FESC_DIS_WAIT = 1<<2, /* Disable TDR Waiting Period */
+ PHY_M_FESC_ENA_MCLK = 1<<1, /* Enable MAC Rx Clock in sleep mode */
+ PHY_M_FESC_SEL_CL_A = 1<<0, /* Select Class A driver (100B-TX) */
+};
+
+/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
+/***** PHY_MARV_PHY_CTRL (page 2) 16 bit r/w MAC Specific Ctrl *****/
+enum {
+ PHY_M_MAC_MD_MSK = 7<<7, /* Bit 9.. 7: Mode Select Mask */
+ PHY_M_MAC_MD_AUTO = 3,/* Auto Copper/1000Base-X */
+ PHY_M_MAC_MD_COPPER = 5,/* Copper only */
+ PHY_M_MAC_MD_1000BX = 7,/* 1000Base-X only */
+};
+#define PHY_M_MAC_MODE_SEL(x) ( ((x)<<7) & PHY_M_MAC_MD_MSK)
+
+/***** PHY_MARV_PHY_CTRL (page 3) 16 bit r/w LED Control Reg. *****/
+enum {
+ PHY_M_LEDC_LOS_MSK = 0xf<<12,/* Bit 15..12: LOS LED Ctrl. Mask */
+ PHY_M_LEDC_INIT_MSK = 0xf<<8, /* Bit 11.. 8: INIT LED Ctrl. Mask */
+ PHY_M_LEDC_STA1_MSK = 0xf<<4,/* Bit 7.. 4: STAT1 LED Ctrl. Mask */
+ PHY_M_LEDC_STA0_MSK = 0xf, /* Bit 3.. 0: STAT0 LED Ctrl. Mask */
+};
+
+#define PHY_M_LEDC_LOS_CTRL(x) ( ((x)<<12) & PHY_M_LEDC_LOS_MSK)
+#define PHY_M_LEDC_INIT_CTRL(x) ( ((x)<<8) & PHY_M_LEDC_INIT_MSK)
+#define PHY_M_LEDC_STA1_CTRL(x) ( ((x)<<4) & PHY_M_LEDC_STA1_MSK)
+#define PHY_M_LEDC_STA0_CTRL(x) ( ((x)<<0) & PHY_M_LEDC_STA0_MSK)
+
+/* GMAC registers */
+/* Port Registers */
+enum {
+ GM_GP_STAT = 0x0000, /* 16 bit r/o General Purpose Status */
+ GM_GP_CTRL = 0x0004, /* 16 bit r/w General Purpose Control */
+ GM_TX_CTRL = 0x0008, /* 16 bit r/w Transmit Control Reg. */
+ GM_RX_CTRL = 0x000c, /* 16 bit r/w Receive Control Reg. */
+ GM_TX_FLOW_CTRL = 0x0010, /* 16 bit r/w Transmit Flow-Control */
+ GM_TX_PARAM = 0x0014, /* 16 bit r/w Transmit Parameter Reg. */
+ GM_SERIAL_MODE = 0x0018, /* 16 bit r/w Serial Mode Register */
+/* Source Address Registers */
+ GM_SRC_ADDR_1L = 0x001c, /* 16 bit r/w Source Address 1 (low) */
+ GM_SRC_ADDR_1M = 0x0020, /* 16 bit r/w Source Address 1 (middle) */
+ GM_SRC_ADDR_1H = 0x0024, /* 16 bit r/w Source Address 1 (high) */
+ GM_SRC_ADDR_2L = 0x0028, /* 16 bit r/w Source Address 2 (low) */
+ GM_SRC_ADDR_2M = 0x002c, /* 16 bit r/w Source Address 2 (middle) */
+ GM_SRC_ADDR_2H = 0x0030, /* 16 bit r/w Source Address 2 (high) */
+
+/* Multicast Address Hash Registers */
+ GM_MC_ADDR_H1 = 0x0034, /* 16 bit r/w Multicast Address Hash 1 */
+ GM_MC_ADDR_H2 = 0x0038, /* 16 bit r/w Multicast Address Hash 2 */
+ GM_MC_ADDR_H3 = 0x003c, /* 16 bit r/w Multicast Address Hash 3 */
+ GM_MC_ADDR_H4 = 0x0040, /* 16 bit r/w Multicast Address Hash 4 */
+
+/* Interrupt Source Registers */
+ GM_TX_IRQ_SRC = 0x0044, /* 16 bit r/o Tx Overflow IRQ Source */
+ GM_RX_IRQ_SRC = 0x0048, /* 16 bit r/o Rx Overflow IRQ Source */
+ GM_TR_IRQ_SRC = 0x004c, /* 16 bit r/o Tx/Rx Over. IRQ Source */
+
+/* Interrupt Mask Registers */
+ GM_TX_IRQ_MSK = 0x0050, /* 16 bit r/w Tx Overflow IRQ Mask */
+ GM_RX_IRQ_MSK = 0x0054, /* 16 bit r/w Rx Overflow IRQ Mask */
+ GM_TR_IRQ_MSK = 0x0058, /* 16 bit r/w Tx/Rx Over. IRQ Mask */
+
+/* Serial Management Interface (SMI) Registers */
+ GM_SMI_CTRL = 0x0080, /* 16 bit r/w SMI Control Register */
+ GM_SMI_DATA = 0x0084, /* 16 bit r/w SMI Data Register */
+ GM_PHY_ADDR = 0x0088, /* 16 bit r/w GPHY Address Register */
+};
+
+/* MIB Counters */
+#define GM_MIB_CNT_BASE 0x0100 /* Base Address of MIB Counters */
+#define GM_MIB_CNT_SIZE 44 /* Number of MIB Counters */
+
+/*
+ * MIB Counters base address definitions (low word) -
+ * use offset 4 for access to high word (32 bit r/o)
+ */
+enum {
+ GM_RXF_UC_OK = GM_MIB_CNT_BASE + 0, /* Unicast Frames Received OK */
+ GM_RXF_BC_OK = GM_MIB_CNT_BASE + 8, /* Broadcast Frames Received OK */
+ GM_RXF_MPAUSE = GM_MIB_CNT_BASE + 16, /* Pause MAC Ctrl Frames Received */
+ GM_RXF_MC_OK = GM_MIB_CNT_BASE + 24, /* Multicast Frames Received OK */
+ GM_RXF_FCS_ERR = GM_MIB_CNT_BASE + 32, /* Rx Frame Check Seq. Error */
+ /* GM_MIB_CNT_BASE + 40: reserved */
+ GM_RXO_OK_LO = GM_MIB_CNT_BASE + 48, /* Octets Received OK Low */
+ GM_RXO_OK_HI = GM_MIB_CNT_BASE + 56, /* Octets Received OK High */
+ GM_RXO_ERR_LO = GM_MIB_CNT_BASE + 64, /* Octets Received Invalid Low */
+ GM_RXO_ERR_HI = GM_MIB_CNT_BASE + 72, /* Octets Received Invalid High */
+ GM_RXF_SHT = GM_MIB_CNT_BASE + 80, /* Frames <64 Byte Received OK */
+ GM_RXE_FRAG = GM_MIB_CNT_BASE + 88, /* Frames <64 Byte Received with FCS Err */
+ GM_RXF_64B = GM_MIB_CNT_BASE + 96, /* 64 Byte Rx Frame */
+ GM_RXF_127B = GM_MIB_CNT_BASE + 104, /* 65-127 Byte Rx Frame */
+ GM_RXF_255B = GM_MIB_CNT_BASE + 112, /* 128-255 Byte Rx Frame */
+ GM_RXF_511B = GM_MIB_CNT_BASE + 120, /* 256-511 Byte Rx Frame */
+ GM_RXF_1023B = GM_MIB_CNT_BASE + 128, /* 512-1023 Byte Rx Frame */
+ GM_RXF_1518B = GM_MIB_CNT_BASE + 136, /* 1024-1518 Byte Rx Frame */
+ GM_RXF_MAX_SZ = GM_MIB_CNT_BASE + 144, /* 1519-MaxSize Byte Rx Frame */
+ GM_RXF_LNG_ERR = GM_MIB_CNT_BASE + 152, /* Rx Frame too Long Error */
+ GM_RXF_JAB_PKT = GM_MIB_CNT_BASE + 160, /* Rx Jabber Packet Frame */
+ /* GM_MIB_CNT_BASE + 168: reserved */
+ GM_RXE_FIFO_OV = GM_MIB_CNT_BASE + 176, /* Rx FIFO overflow Event */
+ /* GM_MIB_CNT_BASE + 184: reserved */
+ GM_TXF_UC_OK = GM_MIB_CNT_BASE + 192, /* Unicast Frames Xmitted OK */
+ GM_TXF_BC_OK = GM_MIB_CNT_BASE + 200, /* Broadcast Frames Xmitted OK */
+ GM_TXF_MPAUSE = GM_MIB_CNT_BASE + 208, /* Pause MAC Ctrl Frames Xmitted */
+ GM_TXF_MC_OK = GM_MIB_CNT_BASE + 216, /* Multicast Frames Xmitted OK */
+ GM_TXO_OK_LO = GM_MIB_CNT_BASE + 224, /* Octets Transmitted OK Low */
+ GM_TXO_OK_HI = GM_MIB_CNT_BASE + 232, /* Octets Transmitted OK High */
+ GM_TXF_64B = GM_MIB_CNT_BASE + 240, /* 64 Byte Tx Frame */
+ GM_TXF_127B = GM_MIB_CNT_BASE + 248, /* 65-127 Byte Tx Frame */
+ GM_TXF_255B = GM_MIB_CNT_BASE + 256, /* 128-255 Byte Tx Frame */
+ GM_TXF_511B = GM_MIB_CNT_BASE + 264, /* 256-511 Byte Tx Frame */
+ GM_TXF_1023B = GM_MIB_CNT_BASE + 272, /* 512-1023 Byte Tx Frame */
+ GM_TXF_1518B = GM_MIB_CNT_BASE + 280, /* 1024-1518 Byte Tx Frame */
+ GM_TXF_MAX_SZ = GM_MIB_CNT_BASE + 288, /* 1519-MaxSize Byte Tx Frame */
+
+ GM_TXF_COL = GM_MIB_CNT_BASE + 304, /* Tx Collision */
+ GM_TXF_LAT_COL = GM_MIB_CNT_BASE + 312, /* Tx Late Collision */
+ GM_TXF_ABO_COL = GM_MIB_CNT_BASE + 320, /* Tx aborted due to Exces. Col. */
+ GM_TXF_MUL_COL = GM_MIB_CNT_BASE + 328, /* Tx Multiple Collision */
+ GM_TXF_SNG_COL = GM_MIB_CNT_BASE + 336, /* Tx Single Collision */
+ GM_TXE_FIFO_UR = GM_MIB_CNT_BASE + 344, /* Tx FIFO Underrun Event */
+};
+
+/* GMAC Bit Definitions */
+/* GM_GP_STAT 16 bit r/o General Purpose Status Register */
+enum {
+ GM_GPSR_SPEED = 1<<15, /* Bit 15: Port Speed (1 = 100 Mbps) */
+ GM_GPSR_DUPLEX = 1<<14, /* Bit 14: Duplex Mode (1 = Full) */
+ GM_GPSR_FC_TX_DIS = 1<<13, /* Bit 13: Tx Flow-Control Mode Disabled */
+ GM_GPSR_LINK_UP = 1<<12, /* Bit 12: Link Up Status */
+ GM_GPSR_PAUSE = 1<<11, /* Bit 11: Pause State */
+ GM_GPSR_TX_ACTIVE = 1<<10, /* Bit 10: Tx in Progress */
+ GM_GPSR_EXC_COL = 1<<9, /* Bit 9: Excessive Collisions Occured */
+ GM_GPSR_LAT_COL = 1<<8, /* Bit 8: Late Collisions Occured */
+
+ GM_GPSR_PHY_ST_CH = 1<<5, /* Bit 5: PHY Status Change */
+ GM_GPSR_GIG_SPEED = 1<<4, /* Bit 4: Gigabit Speed (1 = 1000 Mbps) */
+ GM_GPSR_PART_MODE = 1<<3, /* Bit 3: Partition mode */
+ GM_GPSR_FC_RX_DIS = 1<<2, /* Bit 2: Rx Flow-Control Mode Disabled */
+ GM_GPSR_PROM_EN = 1<<1, /* Bit 1: Promiscuous Mode Enabled */
+};
+
+/* GM_GP_CTRL 16 bit r/w General Purpose Control Register */
+enum {
+ GM_GPCR_PROM_ENA = 1<<14, /* Bit 14: Enable Promiscuous Mode */
+ GM_GPCR_FC_TX_DIS = 1<<13, /* Bit 13: Disable Tx Flow-Control Mode */
+ GM_GPCR_TX_ENA = 1<<12, /* Bit 12: Enable Transmit */
+ GM_GPCR_RX_ENA = 1<<11, /* Bit 11: Enable Receive */
+ GM_GPCR_BURST_ENA = 1<<10, /* Bit 10: Enable Burst Mode */
+ GM_GPCR_LOOP_ENA = 1<<9, /* Bit 9: Enable MAC Loopback Mode */
+ GM_GPCR_PART_ENA = 1<<8, /* Bit 8: Enable Partition Mode */
+ GM_GPCR_GIGS_ENA = 1<<7, /* Bit 7: Gigabit Speed (1000 Mbps) */
+ GM_GPCR_FL_PASS = 1<<6, /* Bit 6: Force Link Pass */
+ GM_GPCR_DUP_FULL = 1<<5, /* Bit 5: Full Duplex Mode */
+ GM_GPCR_FC_RX_DIS = 1<<4, /* Bit 4: Disable Rx Flow-Control Mode */
+ GM_GPCR_SPEED_100 = 1<<3, /* Bit 3: Port Speed 100 Mbps */
+ GM_GPCR_AU_DUP_DIS = 1<<2, /* Bit 2: Disable Auto-Update Duplex */
+ GM_GPCR_AU_FCT_DIS = 1<<1, /* Bit 1: Disable Auto-Update Flow-C. */
+ GM_GPCR_AU_SPD_DIS = 1<<0, /* Bit 0: Disable Auto-Update Speed */
+};
+
+#define GM_GPCR_SPEED_1000 (GM_GPCR_GIGS_ENA | GM_GPCR_SPEED_100)
+#define GM_GPCR_AU_ALL_DIS (GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_FCT_DIS|GM_GPCR_AU_SPD_DIS)
+
+/* GM_TX_CTRL 16 bit r/w Transmit Control Register */
+enum {
+ GM_TXCR_FORCE_JAM = 1<<15, /* Bit 15: Force Jam / Flow-Control */
+ GM_TXCR_CRC_DIS = 1<<14, /* Bit 14: Disable insertion of CRC */
+ GM_TXCR_PAD_DIS = 1<<13, /* Bit 13: Disable padding of packets */
+ GM_TXCR_COL_THR_MSK = 1<<10, /* Bit 12..10: Collision Threshold */
+};
+
+#define TX_COL_THR(x) (((x)<<10) & GM_TXCR_COL_THR_MSK)
+#define TX_COL_DEF 0x04
+
+/* GM_RX_CTRL 16 bit r/w Receive Control Register */
+enum {
+ GM_RXCR_UCF_ENA = 1<<15, /* Bit 15: Enable Unicast filtering */
+ GM_RXCR_MCF_ENA = 1<<14, /* Bit 14: Enable Multicast filtering */
+ GM_RXCR_CRC_DIS = 1<<13, /* Bit 13: Remove 4-byte CRC */
+ GM_RXCR_PASS_FC = 1<<12, /* Bit 12: Pass FC packets to FIFO */
+};
+
+/* GM_TX_PARAM 16 bit r/w Transmit Parameter Register */
+enum {
+ GM_TXPA_JAMLEN_MSK = 0x03<<14, /* Bit 15..14: Jam Length */
+ GM_TXPA_JAMIPG_MSK = 0x1f<<9, /* Bit 13..9: Jam IPG */
+ GM_TXPA_JAMDAT_MSK = 0x1f<<4, /* Bit 8..4: IPG Jam to Data */
+
+ TX_JAM_LEN_DEF = 0x03,
+ TX_JAM_IPG_DEF = 0x0b,
+ TX_IPG_JAM_DEF = 0x1c,
+};
+
+#define TX_JAM_LEN_VAL(x) (((x)<<14) & GM_TXPA_JAMLEN_MSK)
+#define TX_JAM_IPG_VAL(x) (((x)<<9) & GM_TXPA_JAMIPG_MSK)
+#define TX_IPG_JAM_DATA(x) (((x)<<4) & GM_TXPA_JAMDAT_MSK)
+
+
+/* GM_SERIAL_MODE 16 bit r/w Serial Mode Register */
+enum {
+ GM_SMOD_DATABL_MSK = 0x1f<<11, /* Bit 15..11: Data Blinder (r/o) */
+ GM_SMOD_LIMIT_4 = 1<<10, /* Bit 10: 4 consecutive Tx trials */
+ GM_SMOD_VLAN_ENA = 1<<9, /* Bit 9: Enable VLAN (Max. Frame Len) */
+ GM_SMOD_JUMBO_ENA = 1<<8, /* Bit 8: Enable Jumbo (Max. Frame Len) */
+ GM_SMOD_IPG_MSK = 0x1f /* Bit 4..0: Inter-Packet Gap (IPG) */
+};
+
+#define DATA_BLIND_VAL(x) (((x)<<11) & GM_SMOD_DATABL_MSK)
+#define DATA_BLIND_DEF 0x04
+
+#define IPG_DATA_VAL(x) (x & GM_SMOD_IPG_MSK)
+#define IPG_DATA_DEF 0x1e
+
+/* GM_SMI_CTRL 16 bit r/w SMI Control Register */
+enum {
+ GM_SMI_CT_PHY_A_MSK = 0x1f<<11,/* Bit 15..11: PHY Device Address */
+ GM_SMI_CT_REG_A_MSK = 0x1f<<6,/* Bit 10.. 6: PHY Register Address */
+ GM_SMI_CT_OP_RD = 1<<5, /* Bit 5: OpCode Read (0=Write)*/
+ GM_SMI_CT_RD_VAL = 1<<4, /* Bit 4: Read Valid (Read completed) */
+ GM_SMI_CT_BUSY = 1<<3, /* Bit 3: Busy (Operation in progress) */
+};
+
+#define GM_SMI_CT_PHY_AD(x) (((x)<<11) & GM_SMI_CT_PHY_A_MSK)
+#define GM_SMI_CT_REG_AD(x) (((x)<<6) & GM_SMI_CT_REG_A_MSK)
+
+/* GM_PHY_ADDR 16 bit r/w GPHY Address Register */
+enum {
+ GM_PAR_MIB_CLR = 1<<5, /* Bit 5: Set MIB Clear Counter Mode */
+ GM_PAR_MIB_TST = 1<<4, /* Bit 4: MIB Load Counter (Test Mode) */
+};
+
+/* Receive Frame Status Encoding */
+enum {
+ GMR_FS_LEN = 0xffff<<16, /* Bit 31..16: Rx Frame Length */
+ GMR_FS_VLAN = 1<<13, /* Bit 13: VLAN Packet */
+ GMR_FS_JABBER = 1<<12, /* Bit 12: Jabber Packet */
+ GMR_FS_UN_SIZE = 1<<11, /* Bit 11: Undersize Packet */
+ GMR_FS_MC = 1<<10, /* Bit 10: Multicast Packet */
+ GMR_FS_BC = 1<<9, /* Bit 9: Broadcast Packet */
+ GMR_FS_RX_OK = 1<<8, /* Bit 8: Receive OK (Good Packet) */
+ GMR_FS_GOOD_FC = 1<<7, /* Bit 7: Good Flow-Control Packet */
+ GMR_FS_BAD_FC = 1<<6, /* Bit 6: Bad Flow-Control Packet */
+ GMR_FS_MII_ERR = 1<<5, /* Bit 5: MII Error */
+ GMR_FS_LONG_ERR = 1<<4, /* Bit 4: Too Long Packet */
+ GMR_FS_FRAGMENT = 1<<3, /* Bit 3: Fragment */
+
+ GMR_FS_CRC_ERR = 1<<1, /* Bit 1: CRC Error */
+ GMR_FS_RX_FF_OV = 1<<0, /* Bit 0: Rx FIFO Overflow */
+
+/*
+ * GMR_FS_ANY_ERR (analogous to XMR_FS_ANY_ERR)
+ */
+ GMR_FS_ANY_ERR = GMR_FS_CRC_ERR | GMR_FS_LONG_ERR |
+ GMR_FS_MII_ERR | GMR_FS_BAD_FC | GMR_FS_GOOD_FC |
+ GMR_FS_JABBER,
+/* Rx GMAC FIFO Flush Mask (default) */
+ RX_FF_FL_DEF_MSK = GMR_FS_CRC_ERR | GMR_FS_RX_FF_OV |GMR_FS_MII_ERR |
+ GMR_FS_BAD_FC | GMR_FS_GOOD_FC | GMR_FS_UN_SIZE |
+ GMR_FS_JABBER,
+};
+
+/* RX_GMF_CTRL_T 32 bit Rx GMAC FIFO Control/Test */
+enum {
+ GMF_WP_TST_ON = 1<<14, /* Write Pointer Test On */
+ GMF_WP_TST_OFF = 1<<13, /* Write Pointer Test Off */
+ GMF_WP_STEP = 1<<12, /* Write Pointer Step/Increment */
+
+ GMF_RP_TST_ON = 1<<10, /* Read Pointer Test On */
+ GMF_RP_TST_OFF = 1<<9, /* Read Pointer Test Off */
+ GMF_RP_STEP = 1<<8, /* Read Pointer Step/Increment */
+ GMF_RX_F_FL_ON = 1<<7, /* Rx FIFO Flush Mode On */
+ GMF_RX_F_FL_OFF = 1<<6, /* Rx FIFO Flush Mode Off */
+ GMF_CLI_RX_FO = 1<<5, /* Clear IRQ Rx FIFO Overrun */
+ GMF_CLI_RX_FC = 1<<4, /* Clear IRQ Rx Frame Complete */
+ GMF_OPER_ON = 1<<3, /* Operational Mode On */
+ GMF_OPER_OFF = 1<<2, /* Operational Mode Off */
+ GMF_RST_CLR = 1<<1, /* Clear GMAC FIFO Reset */
+ GMF_RST_SET = 1<<0, /* Set GMAC FIFO Reset */
+
+ RX_GMF_FL_THR_DEF = 0xa, /* flush threshold (default) */
+};
+
+
+/* TX_GMF_CTRL_T 32 bit Tx GMAC FIFO Control/Test */
+enum {
+ GMF_WSP_TST_ON = 1<<18,/* Write Shadow Pointer Test On */
+ GMF_WSP_TST_OFF = 1<<17,/* Write Shadow Pointer Test Off */
+ GMF_WSP_STEP = 1<<16,/* Write Shadow Pointer Step/Increment */
+
+ GMF_CLI_TX_FU = 1<<6, /* Clear IRQ Tx FIFO Underrun */
+ GMF_CLI_TX_FC = 1<<5, /* Clear IRQ Tx Frame Complete */
+ GMF_CLI_TX_PE = 1<<4, /* Clear IRQ Tx Parity Error */
+};
+
+/* GMAC_TI_ST_CTRL 8 bit Time Stamp Timer Ctrl Reg (YUKON only) */
+enum {
+ GMT_ST_START = 1<<2, /* Start Time Stamp Timer */
+ GMT_ST_STOP = 1<<1, /* Stop Time Stamp Timer */
+ GMT_ST_CLR_IRQ = 1<<0, /* Clear Time Stamp Timer IRQ */
+};
+
+/* GMAC_CTRL 32 bit GMAC Control Reg (YUKON only) */
+enum {
+ GMC_H_BURST_ON = 1<<7, /* Half Duplex Burst Mode On */
+ GMC_H_BURST_OFF = 1<<6, /* Half Duplex Burst Mode Off */
+ GMC_F_LOOPB_ON = 1<<5, /* FIFO Loopback On */
+ GMC_F_LOOPB_OFF = 1<<4, /* FIFO Loopback Off */
+ GMC_PAUSE_ON = 1<<3, /* Pause On */
+ GMC_PAUSE_OFF = 1<<2, /* Pause Off */
+ GMC_RST_CLR = 1<<1, /* Clear GMAC Reset */
+ GMC_RST_SET = 1<<0, /* Set GMAC Reset */
+};
+
+/* GPHY_CTRL 32 bit GPHY Control Reg (YUKON only) */
+enum {
+ GPC_SEL_BDT = 1<<28, /* Select Bi-Dir. Transfer for MDC/MDIO */
+ GPC_INT_POL_HI = 1<<27, /* IRQ Polarity is Active HIGH */
+ GPC_75_OHM = 1<<26, /* Use 75 Ohm Termination instead of 50 */
+ GPC_DIS_FC = 1<<25, /* Disable Automatic Fiber/Copper Detection */
+ GPC_DIS_SLEEP = 1<<24, /* Disable Energy Detect */
+ GPC_HWCFG_M_3 = 1<<23, /* HWCFG_MODE[3] */
+ GPC_HWCFG_M_2 = 1<<22, /* HWCFG_MODE[2] */
+ GPC_HWCFG_M_1 = 1<<21, /* HWCFG_MODE[1] */
+ GPC_HWCFG_M_0 = 1<<20, /* HWCFG_MODE[0] */
+ GPC_ANEG_0 = 1<<19, /* ANEG[0] */
+ GPC_ENA_XC = 1<<18, /* Enable MDI crossover */
+ GPC_DIS_125 = 1<<17, /* Disable 125 MHz clock */
+ GPC_ANEG_3 = 1<<16, /* ANEG[3] */
+ GPC_ANEG_2 = 1<<15, /* ANEG[2] */
+ GPC_ANEG_1 = 1<<14, /* ANEG[1] */
+ GPC_ENA_PAUSE = 1<<13, /* Enable Pause (SYM_OR_REM) */
+ GPC_PHYADDR_4 = 1<<12, /* Bit 4 of Phy Addr */
+ GPC_PHYADDR_3 = 1<<11, /* Bit 3 of Phy Addr */
+ GPC_PHYADDR_2 = 1<<10, /* Bit 2 of Phy Addr */
+ GPC_PHYADDR_1 = 1<<9, /* Bit 1 of Phy Addr */
+ GPC_PHYADDR_0 = 1<<8, /* Bit 0 of Phy Addr */
+ /* Bits 7..2: reserved */
+ GPC_RST_CLR = 1<<1, /* Clear GPHY Reset */
+ GPC_RST_SET = 1<<0, /* Set GPHY Reset */
+};
+
+#define GPC_HWCFG_GMII_COP (GPC_HWCFG_M_3|GPC_HWCFG_M_2 | GPC_HWCFG_M_1 | GPC_HWCFG_M_0)
+#define GPC_HWCFG_GMII_FIB (GPC_HWCFG_M_2 | GPC_HWCFG_M_1 | GPC_HWCFG_M_0)
+#define GPC_ANEG_ADV_ALL_M (GPC_ANEG_3 | GPC_ANEG_2 | GPC_ANEG_1 | GPC_ANEG_0)
+
+/* forced speed and duplex mode (don't mix with other ANEG bits) */
+#define GPC_FRC10MBIT_HALF 0
+#define GPC_FRC10MBIT_FULL GPC_ANEG_0
+#define GPC_FRC100MBIT_HALF GPC_ANEG_1
+#define GPC_FRC100MBIT_FULL (GPC_ANEG_0 | GPC_ANEG_1)
+
+/* auto-negotiation with limited advertised speeds */
+/* mix only with master/slave settings (for copper) */
+#define GPC_ADV_1000_HALF GPC_ANEG_2
+#define GPC_ADV_1000_FULL GPC_ANEG_3
+#define GPC_ADV_ALL (GPC_ANEG_2 | GPC_ANEG_3)
+
+/* master/slave settings */
+/* only for copper with 1000 Mbps */
+#define GPC_FORCE_MASTER 0
+#define GPC_FORCE_SLAVE GPC_ANEG_0
+#define GPC_PREF_MASTER GPC_ANEG_1
+#define GPC_PREF_SLAVE (GPC_ANEG_1 | GPC_ANEG_0)
+
+/* GMAC_IRQ_SRC 8 bit GMAC Interrupt Source Reg (YUKON only) */
+/* GMAC_IRQ_MSK 8 bit GMAC Interrupt Mask Reg (YUKON only) */
+enum {
+ GM_IS_TX_CO_OV = 1<<5, /* Transmit Counter Overflow IRQ */
+ GM_IS_RX_CO_OV = 1<<4, /* Receive Counter Overflow IRQ */
+ GM_IS_TX_FF_UR = 1<<3, /* Transmit FIFO Underrun */
+ GM_IS_TX_COMPL = 1<<2, /* Frame Transmission Complete */
+ GM_IS_RX_FF_OR = 1<<1, /* Receive FIFO Overrun */
+ GM_IS_RX_COMPL = 1<<0, /* Frame Reception Complete */
+
+#define GMAC_DEF_MSK (GM_IS_TX_CO_OV | GM_IS_RX_CO_OV | GM_IS_TX_FF_UR)
+
+/* GMAC_LINK_CTRL 16 bit GMAC Link Control Reg (YUKON only) */
+ /* Bits 15.. 2: reserved */
+ GMLC_RST_CLR = 1<<1, /* Clear GMAC Link Reset */
+ GMLC_RST_SET = 1<<0, /* Set GMAC Link Reset */
+
+
+/* WOL_CTRL_STAT 16 bit WOL Control/Status Reg */
+ WOL_CTL_LINK_CHG_OCC = 1<<15,
+ WOL_CTL_MAGIC_PKT_OCC = 1<<14,
+ WOL_CTL_PATTERN_OCC = 1<<13,
+ WOL_CTL_CLEAR_RESULT = 1<<12,
+ WOL_CTL_ENA_PME_ON_LINK_CHG = 1<<11,
+ WOL_CTL_DIS_PME_ON_LINK_CHG = 1<<10,
+ WOL_CTL_ENA_PME_ON_MAGIC_PKT = 1<<9,
+ WOL_CTL_DIS_PME_ON_MAGIC_PKT = 1<<8,
+ WOL_CTL_ENA_PME_ON_PATTERN = 1<<7,
+ WOL_CTL_DIS_PME_ON_PATTERN = 1<<6,
+ WOL_CTL_ENA_LINK_CHG_UNIT = 1<<5,
+ WOL_CTL_DIS_LINK_CHG_UNIT = 1<<4,
+ WOL_CTL_ENA_MAGIC_PKT_UNIT = 1<<3,
+ WOL_CTL_DIS_MAGIC_PKT_UNIT = 1<<2,
+ WOL_CTL_ENA_PATTERN_UNIT = 1<<1,
+ WOL_CTL_DIS_PATTERN_UNIT = 1<<0,
+};
+
+#define WOL_CTL_DEFAULT \
+ (WOL_CTL_DIS_PME_ON_LINK_CHG | \
+ WOL_CTL_DIS_PME_ON_PATTERN | \
+ WOL_CTL_DIS_PME_ON_MAGIC_PKT | \
+ WOL_CTL_DIS_LINK_CHG_UNIT | \
+ WOL_CTL_DIS_PATTERN_UNIT | \
+ WOL_CTL_DIS_MAGIC_PKT_UNIT)
+
+/* WOL_MATCH_CTL 8 bit WOL Match Control Reg */
+#define WOL_CTL_PATT_ENA(x) (1 << (x))
+
+
+/* XMAC II registers */
+enum {
+ XM_MMU_CMD = 0x0000, /* 16 bit r/w MMU Command Register */
+ XM_POFF = 0x0008, /* 32 bit r/w Packet Offset Register */
+ XM_BURST = 0x000c, /* 32 bit r/w Burst Register for half duplex*/
+ XM_1L_VLAN_TAG = 0x0010, /* 16 bit r/w One Level VLAN Tag ID */
+ XM_2L_VLAN_TAG = 0x0014, /* 16 bit r/w Two Level VLAN Tag ID */
+ XM_TX_CMD = 0x0020, /* 16 bit r/w Transmit Command Register */
+ XM_TX_RT_LIM = 0x0024, /* 16 bit r/w Transmit Retry Limit Register */
+ XM_TX_STIME = 0x0028, /* 16 bit r/w Transmit Slottime Register */
+ XM_TX_IPG = 0x002c, /* 16 bit r/w Transmit Inter Packet Gap */
+ XM_RX_CMD = 0x0030, /* 16 bit r/w Receive Command Register */
+ XM_PHY_ADDR = 0x0034, /* 16 bit r/w PHY Address Register */
+ XM_PHY_DATA = 0x0038, /* 16 bit r/w PHY Data Register */
+ XM_GP_PORT = 0x0040, /* 32 bit r/w General Purpose Port Register */
+ XM_IMSK = 0x0044, /* 16 bit r/w Interrupt Mask Register */
+ XM_ISRC = 0x0048, /* 16 bit r/o Interrupt Status Register */
+ XM_HW_CFG = 0x004c, /* 16 bit r/w Hardware Config Register */
+ XM_TX_LO_WM = 0x0060, /* 16 bit r/w Tx FIFO Low Water Mark */
+ XM_TX_HI_WM = 0x0062, /* 16 bit r/w Tx FIFO High Water Mark */
+ XM_TX_THR = 0x0064, /* 16 bit r/w Tx Request Threshold */
+ XM_HT_THR = 0x0066, /* 16 bit r/w Host Request Threshold */
+ XM_PAUSE_DA = 0x0068, /* NA reg r/w Pause Destination Address */
+ XM_CTL_PARA = 0x0070, /* 32 bit r/w Control Parameter Register */
+ XM_MAC_OPCODE = 0x0074, /* 16 bit r/w Opcode for MAC control frames */
+ XM_MAC_PTIME = 0x0076, /* 16 bit r/w Pause time for MAC ctrl frames*/
+ XM_TX_STAT = 0x0078, /* 32 bit r/o Tx Status LIFO Register */
+
+ XM_EXM_START = 0x0080, /* r/w Start Address of the EXM Regs */
+#define XM_EXM(reg) (XM_EXM_START + ((reg) << 3))
+};
+
+enum {
+ XM_SRC_CHK = 0x0100, /* NA reg r/w Source Check Address Register */
+ XM_SA = 0x0108, /* NA reg r/w Station Address Register */
+ XM_HSM = 0x0110, /* 64 bit r/w Hash Match Address Registers */
+ XM_RX_LO_WM = 0x0118, /* 16 bit r/w Receive Low Water Mark */
+ XM_RX_HI_WM = 0x011a, /* 16 bit r/w Receive High Water Mark */
+ XM_RX_THR = 0x011c, /* 32 bit r/w Receive Request Threshold */
+ XM_DEV_ID = 0x0120, /* 32 bit r/o Device ID Register */
+ XM_MODE = 0x0124, /* 32 bit r/w Mode Register */
+ XM_LSA = 0x0128, /* NA reg r/o Last Source Register */
+ XM_TS_READ = 0x0130, /* 32 bit r/o Time Stamp Read Register */
+ XM_TS_LOAD = 0x0134, /* 32 bit r/o Time Stamp Load Value */
+ XM_STAT_CMD = 0x0200, /* 16 bit r/w Statistics Command Register */
+ XM_RX_CNT_EV = 0x0204, /* 32 bit r/o Rx Counter Event Register */
+ XM_TX_CNT_EV = 0x0208, /* 32 bit r/o Tx Counter Event Register */
+ XM_RX_EV_MSK = 0x020c, /* 32 bit r/w Rx Counter Event Mask */
+ XM_TX_EV_MSK = 0x0210, /* 32 bit r/w Tx Counter Event Mask */
+ XM_TXF_OK = 0x0280, /* 32 bit r/o Frames Transmitted OK Conuter */
+ XM_TXO_OK_HI = 0x0284, /* 32 bit r/o Octets Transmitted OK High Cnt*/
+ XM_TXO_OK_LO = 0x0288, /* 32 bit r/o Octets Transmitted OK Low Cnt */
+ XM_TXF_BC_OK = 0x028c, /* 32 bit r/o Broadcast Frames Xmitted OK */
+ XM_TXF_MC_OK = 0x0290, /* 32 bit r/o Multicast Frames Xmitted OK */
+ XM_TXF_UC_OK = 0x0294, /* 32 bit r/o Unicast Frames Xmitted OK */
+ XM_TXF_LONG = 0x0298, /* 32 bit r/o Tx Long Frame Counter */
+ XM_TXE_BURST = 0x029c, /* 32 bit r/o Tx Burst Event Counter */
+ XM_TXF_MPAUSE = 0x02a0, /* 32 bit r/o Tx Pause MAC Ctrl Frame Cnt */
+ XM_TXF_MCTRL = 0x02a4, /* 32 bit r/o Tx MAC Ctrl Frame Counter */
+ XM_TXF_SNG_COL = 0x02a8, /* 32 bit r/o Tx Single Collision Counter */
+ XM_TXF_MUL_COL = 0x02ac, /* 32 bit r/o Tx Multiple Collision Counter */
+ XM_TXF_ABO_COL = 0x02b0, /* 32 bit r/o Tx aborted due to Exces. Col. */
+ XM_TXF_LAT_COL = 0x02b4, /* 32 bit r/o Tx Late Collision Counter */
+ XM_TXF_DEF = 0x02b8, /* 32 bit r/o Tx Deferred Frame Counter */
+ XM_TXF_EX_DEF = 0x02bc, /* 32 bit r/o Tx Excessive Deferall Counter */
+ XM_TXE_FIFO_UR = 0x02c0, /* 32 bit r/o Tx FIFO Underrun Event Cnt */
+ XM_TXE_CS_ERR = 0x02c4, /* 32 bit r/o Tx Carrier Sense Error Cnt */
+ XM_TXP_UTIL = 0x02c8, /* 32 bit r/o Tx Utilization in % */
+ XM_TXF_64B = 0x02d0, /* 32 bit r/o 64 Byte Tx Frame Counter */
+ XM_TXF_127B = 0x02d4, /* 32 bit r/o 65-127 Byte Tx Frame Counter */
+ XM_TXF_255B = 0x02d8, /* 32 bit r/o 128-255 Byte Tx Frame Counter */
+ XM_TXF_511B = 0x02dc, /* 32 bit r/o 256-511 Byte Tx Frame Counter */
+ XM_TXF_1023B = 0x02e0, /* 32 bit r/o 512-1023 Byte Tx Frame Counter*/
+ XM_TXF_MAX_SZ = 0x02e4, /* 32 bit r/o 1024-MaxSize Byte Tx Frame Cnt*/
+ XM_RXF_OK = 0x0300, /* 32 bit r/o Frames Received OK */
+ XM_RXO_OK_HI = 0x0304, /* 32 bit r/o Octets Received OK High Cnt */
+ XM_RXO_OK_LO = 0x0308, /* 32 bit r/o Octets Received OK Low Counter*/
+ XM_RXF_BC_OK = 0x030c, /* 32 bit r/o Broadcast Frames Received OK */
+ XM_RXF_MC_OK = 0x0310, /* 32 bit r/o Multicast Frames Received OK */
+ XM_RXF_UC_OK = 0x0314, /* 32 bit r/o Unicast Frames Received OK */
+ XM_RXF_MPAUSE = 0x0318, /* 32 bit r/o Rx Pause MAC Ctrl Frame Cnt */
+ XM_RXF_MCTRL = 0x031c, /* 32 bit r/o Rx MAC Ctrl Frame Counter */
+ XM_RXF_INV_MP = 0x0320, /* 32 bit r/o Rx invalid Pause Frame Cnt */
+ XM_RXF_INV_MOC = 0x0324, /* 32 bit r/o Rx Frames with inv. MAC Opcode*/
+ XM_RXE_BURST = 0x0328, /* 32 bit r/o Rx Burst Event Counter */
+ XM_RXE_FMISS = 0x032c, /* 32 bit r/o Rx Missed Frames Event Cnt */
+ XM_RXF_FRA_ERR = 0x0330, /* 32 bit r/o Rx Framing Error Counter */
+ XM_RXE_FIFO_OV = 0x0334, /* 32 bit r/o Rx FIFO overflow Event Cnt */
+ XM_RXF_JAB_PKT = 0x0338, /* 32 bit r/o Rx Jabber Packet Frame Cnt */
+ XM_RXE_CAR_ERR = 0x033c, /* 32 bit r/o Rx Carrier Event Error Cnt */
+ XM_RXF_LEN_ERR = 0x0340, /* 32 bit r/o Rx in Range Length Error */
+ XM_RXE_SYM_ERR = 0x0344, /* 32 bit r/o Rx Symbol Error Counter */
+ XM_RXE_SHT_ERR = 0x0348, /* 32 bit r/o Rx Short Event Error Cnt */
+ XM_RXE_RUNT = 0x034c, /* 32 bit r/o Rx Runt Event Counter */
+ XM_RXF_LNG_ERR = 0x0350, /* 32 bit r/o Rx Frame too Long Error Cnt */
+ XM_RXF_FCS_ERR = 0x0354, /* 32 bit r/o Rx Frame Check Seq. Error Cnt */
+ XM_RXF_CEX_ERR = 0x035c, /* 32 bit r/o Rx Carrier Ext Error Frame Cnt*/
+ XM_RXP_UTIL = 0x0360, /* 32 bit r/o Rx Utilization in % */
+ XM_RXF_64B = 0x0368, /* 32 bit r/o 64 Byte Rx Frame Counter */
+ XM_RXF_127B = 0x036c, /* 32 bit r/o 65-127 Byte Rx Frame Counter */
+ XM_RXF_255B = 0x0370, /* 32 bit r/o 128-255 Byte Rx Frame Counter */
+ XM_RXF_511B = 0x0374, /* 32 bit r/o 256-511 Byte Rx Frame Counter */
+ XM_RXF_1023B = 0x0378, /* 32 bit r/o 512-1023 Byte Rx Frame Counter*/
+ XM_RXF_MAX_SZ = 0x037c, /* 32 bit r/o 1024-MaxSize Byte Rx Frame Cnt*/
+};
+
+/* XM_MMU_CMD 16 bit r/w MMU Command Register */
+enum {
+ XM_MMU_PHY_RDY = 1<<12,/* Bit 12: PHY Read Ready */
+ XM_MMU_PHY_BUSY = 1<<11,/* Bit 11: PHY Busy */
+ XM_MMU_IGN_PF = 1<<10,/* Bit 10: Ignore Pause Frame */
+ XM_MMU_MAC_LB = 1<<9, /* Bit 9: Enable MAC Loopback */
+ XM_MMU_FRC_COL = 1<<7, /* Bit 7: Force Collision */
+ XM_MMU_SIM_COL = 1<<6, /* Bit 6: Simulate Collision */
+ XM_MMU_NO_PRE = 1<<5, /* Bit 5: No MDIO Preamble */
+ XM_MMU_GMII_FD = 1<<4, /* Bit 4: GMII uses Full Duplex */
+ XM_MMU_RAT_CTRL = 1<<3, /* Bit 3: Enable Rate Control */
+ XM_MMU_GMII_LOOP= 1<<2, /* Bit 2: PHY is in Loopback Mode */
+ XM_MMU_ENA_RX = 1<<1, /* Bit 1: Enable Receiver */
+ XM_MMU_ENA_TX = 1<<0, /* Bit 0: Enable Transmitter */
+};
+
+
+/* XM_TX_CMD 16 bit r/w Transmit Command Register */
+enum {
+ XM_TX_BK2BK = 1<<6, /* Bit 6: Ignor Carrier Sense (Tx Bk2Bk)*/
+ XM_TX_ENC_BYP = 1<<5, /* Bit 5: Set Encoder in Bypass Mode */
+ XM_TX_SAM_LINE = 1<<4, /* Bit 4: (sc) Start utilization calculation */
+ XM_TX_NO_GIG_MD = 1<<3, /* Bit 3: Disable Carrier Extension */
+ XM_TX_NO_PRE = 1<<2, /* Bit 2: Disable Preamble Generation */
+ XM_TX_NO_CRC = 1<<1, /* Bit 1: Disable CRC Generation */
+ XM_TX_AUTO_PAD = 1<<0, /* Bit 0: Enable Automatic Padding */
+};
+
+/* XM_TX_RT_LIM 16 bit r/w Transmit Retry Limit Register */
+#define XM_RT_LIM_MSK 0x1f /* Bit 4..0: Tx Retry Limit */
+
+
+/* XM_TX_STIME 16 bit r/w Transmit Slottime Register */
+#define XM_STIME_MSK 0x7f /* Bit 6..0: Tx Slottime bits */
+
+
+/* XM_TX_IPG 16 bit r/w Transmit Inter Packet Gap */
+#define XM_IPG_MSK 0xff /* Bit 7..0: IPG value bits */
+
+
+/* XM_RX_CMD 16 bit r/w Receive Command Register */
+enum {
+ XM_RX_LENERR_OK = 1<<8, /* Bit 8 don't set Rx Err bit for */
+ /* inrange error packets */
+ XM_RX_BIG_PK_OK = 1<<7, /* Bit 7 don't set Rx Err bit for */
+ /* jumbo packets */
+ XM_RX_IPG_CAP = 1<<6, /* Bit 6 repl. type field with IPG */
+ XM_RX_TP_MD = 1<<5, /* Bit 5: Enable transparent Mode */
+ XM_RX_STRIP_FCS = 1<<4, /* Bit 4: Enable FCS Stripping */
+ XM_RX_SELF_RX = 1<<3, /* Bit 3: Enable Rx of own packets */
+ XM_RX_SAM_LINE = 1<<2, /* Bit 2: (sc) Start utilization calculation */
+ XM_RX_STRIP_PAD = 1<<1, /* Bit 1: Strip pad bytes of Rx frames */
+ XM_RX_DIS_CEXT = 1<<0, /* Bit 0: Disable carrier ext. check */
+};
+
+
+/* XM_PHY_ADDR 16 bit r/w PHY Address Register */
+#define XM_PHY_ADDR_SZ 0x1f /* Bit 4..0: PHY Address bits */
+
+
+/* XM_GP_PORT 32 bit r/w General Purpose Port Register */
+enum {
+ XM_GP_ANIP = 1<<6, /* Bit 6: (ro) Auto-Neg. in progress */
+ XM_GP_FRC_INT = 1<<5, /* Bit 5: (sc) Force Interrupt */
+ XM_GP_RES_MAC = 1<<3, /* Bit 3: (sc) Reset MAC and FIFOs */
+ XM_GP_RES_STAT = 1<<2, /* Bit 2: (sc) Reset the statistics module */
+ XM_GP_INP_ASS = 1<<0, /* Bit 0: (ro) GP Input Pin asserted */
+};
+
+
+/* XM_IMSK 16 bit r/w Interrupt Mask Register */
+/* XM_ISRC 16 bit r/o Interrupt Status Register */
+enum {
+ XM_IS_LNK_AE = 1<<14, /* Bit 14: Link Asynchronous Event */
+ XM_IS_TX_ABORT = 1<<13, /* Bit 13: Transmit Abort, late Col. etc */
+ XM_IS_FRC_INT = 1<<12, /* Bit 12: Force INT bit set in GP */
+ XM_IS_INP_ASS = 1<<11, /* Bit 11: Input Asserted, GP bit 0 set */
+ XM_IS_LIPA_RC = 1<<10, /* Bit 10: Link Partner requests config */
+ XM_IS_RX_PAGE = 1<<9, /* Bit 9: Page Received */
+ XM_IS_TX_PAGE = 1<<8, /* Bit 8: Next Page Loaded for Transmit */
+ XM_IS_AND = 1<<7, /* Bit 7: Auto-Negotiation Done */
+ XM_IS_TSC_OV = 1<<6, /* Bit 6: Time Stamp Counter Overflow */
+ XM_IS_RXC_OV = 1<<5, /* Bit 5: Rx Counter Event Overflow */
+ XM_IS_TXC_OV = 1<<4, /* Bit 4: Tx Counter Event Overflow */
+ XM_IS_RXF_OV = 1<<3, /* Bit 3: Receive FIFO Overflow */
+ XM_IS_TXF_UR = 1<<2, /* Bit 2: Transmit FIFO Underrun */
+ XM_IS_TX_COMP = 1<<1, /* Bit 1: Frame Tx Complete */
+ XM_IS_RX_COMP = 1<<0, /* Bit 0: Frame Rx Complete */
+};
+
+#define XM_DEF_MSK (~(XM_IS_INP_ASS | XM_IS_LIPA_RC | XM_IS_RX_PAGE | \
+ XM_IS_AND | XM_IS_RXC_OV | XM_IS_TXC_OV | \
+ XM_IS_RXF_OV | XM_IS_TXF_UR))
+
+
+/* XM_HW_CFG 16 bit r/w Hardware Config Register */
+enum {
+ XM_HW_GEN_EOP = 1<<3, /* Bit 3: generate End of Packet pulse */
+ XM_HW_COM4SIG = 1<<2, /* Bit 2: use Comma Detect for Sig. Det.*/
+ XM_HW_GMII_MD = 1<<0, /* Bit 0: GMII Interface selected */
+};
+
+
+/* XM_TX_LO_WM 16 bit r/w Tx FIFO Low Water Mark */
+/* XM_TX_HI_WM 16 bit r/w Tx FIFO High Water Mark */
+#define XM_TX_WM_MSK 0x01ff /* Bit 9.. 0 Tx FIFO Watermark bits */
+
+/* XM_TX_THR 16 bit r/w Tx Request Threshold */
+/* XM_HT_THR 16 bit r/w Host Request Threshold */
+/* XM_RX_THR 16 bit r/w Rx Request Threshold */
+#define XM_THR_MSK 0x03ff /* Bit 10.. 0 Rx/Tx Request Threshold bits */
+
+
+/* XM_TX_STAT 32 bit r/o Tx Status LIFO Register */
+enum {
+ XM_ST_VALID = (1UL<<31), /* Bit 31: Status Valid */
+ XM_ST_BYTE_CNT = (0x3fffL<<17), /* Bit 30..17: Tx frame Length */
+ XM_ST_RETRY_CNT = (0x1fL<<12), /* Bit 16..12: Retry Count */
+ XM_ST_EX_COL = 1<<11, /* Bit 11: Excessive Collisions */
+ XM_ST_EX_DEF = 1<<10, /* Bit 10: Excessive Deferral */
+ XM_ST_BURST = 1<<9, /* Bit 9: p. xmitted in burst md*/
+ XM_ST_DEFER = 1<<8, /* Bit 8: packet was defered */
+ XM_ST_BC = 1<<7, /* Bit 7: Broadcast packet */
+ XM_ST_MC = 1<<6, /* Bit 6: Multicast packet */
+ XM_ST_UC = 1<<5, /* Bit 5: Unicast packet */
+ XM_ST_TX_UR = 1<<4, /* Bit 4: FIFO Underrun occured */
+ XM_ST_CS_ERR = 1<<3, /* Bit 3: Carrier Sense Error */
+ XM_ST_LAT_COL = 1<<2, /* Bit 2: Late Collision Error */
+ XM_ST_MUL_COL = 1<<1, /* Bit 1: Multiple Collisions */
+ XM_ST_SGN_COL = 1<<0, /* Bit 0: Single Collision */
+};
+
+/* XM_RX_LO_WM 16 bit r/w Receive Low Water Mark */
+/* XM_RX_HI_WM 16 bit r/w Receive High Water Mark */
+#define XM_RX_WM_MSK 0x03ff /* Bit 11.. 0: Rx FIFO Watermark bits */
+
+
+/* XM_DEV_ID 32 bit r/o Device ID Register */
+#define XM_DEV_OUI (0x00ffffffUL<<8) /* Bit 31..8: Device OUI */
+#define XM_DEV_REV (0x07L << 5) /* Bit 7..5: Chip Rev Num */
+
+
+/* XM_MODE 32 bit r/w Mode Register */
+enum {
+ XM_MD_ENA_REJ = 1<<26, /* Bit 26: Enable Frame Reject */
+ XM_MD_SPOE_E = 1<<25, /* Bit 25: Send Pause on Edge */
+ /* extern generated */
+ XM_MD_TX_REP = 1<<24, /* Bit 24: Transmit Repeater Mode */
+ XM_MD_SPOFF_I = 1<<23, /* Bit 23: Send Pause on FIFO full */
+ /* intern generated */
+ XM_MD_LE_STW = 1<<22, /* Bit 22: Rx Stat Word in Little Endian */
+ XM_MD_TX_CONT = 1<<21, /* Bit 21: Send Continuous */
+ XM_MD_TX_PAUSE = 1<<20, /* Bit 20: (sc) Send Pause Frame */
+ XM_MD_ATS = 1<<19, /* Bit 19: Append Time Stamp */
+ XM_MD_SPOL_I = 1<<18, /* Bit 18: Send Pause on Low */
+ /* intern generated */
+ XM_MD_SPOH_I = 1<<17, /* Bit 17: Send Pause on High */
+ /* intern generated */
+ XM_MD_CAP = 1<<16, /* Bit 16: Check Address Pair */
+ XM_MD_ENA_HASH = 1<<15, /* Bit 15: Enable Hashing */
+ XM_MD_CSA = 1<<14, /* Bit 14: Check Station Address */
+ XM_MD_CAA = 1<<13, /* Bit 13: Check Address Array */
+ XM_MD_RX_MCTRL = 1<<12, /* Bit 12: Rx MAC Control Frame */
+ XM_MD_RX_RUNT = 1<<11, /* Bit 11: Rx Runt Frames */
+ XM_MD_RX_IRLE = 1<<10, /* Bit 10: Rx in Range Len Err Frame */
+ XM_MD_RX_LONG = 1<<9, /* Bit 9: Rx Long Frame */
+ XM_MD_RX_CRCE = 1<<8, /* Bit 8: Rx CRC Error Frame */
+ XM_MD_RX_ERR = 1<<7, /* Bit 7: Rx Error Frame */
+ XM_MD_DIS_UC = 1<<6, /* Bit 6: Disable Rx Unicast */
+ XM_MD_DIS_MC = 1<<5, /* Bit 5: Disable Rx Multicast */
+ XM_MD_DIS_BC = 1<<4, /* Bit 4: Disable Rx Broadcast */
+ XM_MD_ENA_PROM = 1<<3, /* Bit 3: Enable Promiscuous */
+ XM_MD_ENA_BE = 1<<2, /* Bit 2: Enable Big Endian */
+ XM_MD_FTF = 1<<1, /* Bit 1: (sc) Flush Tx FIFO */
+ XM_MD_FRF = 1<<0, /* Bit 0: (sc) Flush Rx FIFO */
+};
+
+#define XM_PAUSE_MODE (XM_MD_SPOE_E | XM_MD_SPOL_I | XM_MD_SPOH_I)
+#define XM_DEF_MODE (XM_MD_RX_RUNT | XM_MD_RX_IRLE | XM_MD_RX_LONG |\
+ XM_MD_RX_CRCE | XM_MD_RX_ERR | XM_MD_CSA | XM_MD_CAA)
+
+/* XM_STAT_CMD 16 bit r/w Statistics Command Register */
+enum {
+ XM_SC_SNP_RXC = 1<<5, /* Bit 5: (sc) Snap Rx Counters */
+ XM_SC_SNP_TXC = 1<<4, /* Bit 4: (sc) Snap Tx Counters */
+ XM_SC_CP_RXC = 1<<3, /* Bit 3: Copy Rx Counters Continuously */
+ XM_SC_CP_TXC = 1<<2, /* Bit 2: Copy Tx Counters Continuously */
+ XM_SC_CLR_RXC = 1<<1, /* Bit 1: (sc) Clear Rx Counters */
+ XM_SC_CLR_TXC = 1<<0, /* Bit 0: (sc) Clear Tx Counters */
+};
+
+
+/* XM_RX_CNT_EV 32 bit r/o Rx Counter Event Register */
+/* XM_RX_EV_MSK 32 bit r/w Rx Counter Event Mask */
+enum {
+ XMR_MAX_SZ_OV = 1<<31, /* Bit 31: 1024-MaxSize Rx Cnt Ov*/
+ XMR_1023B_OV = 1<<30, /* Bit 30: 512-1023Byte Rx Cnt Ov*/
+ XMR_511B_OV = 1<<29, /* Bit 29: 256-511 Byte Rx Cnt Ov*/
+ XMR_255B_OV = 1<<28, /* Bit 28: 128-255 Byte Rx Cnt Ov*/
+ XMR_127B_OV = 1<<27, /* Bit 27: 65-127 Byte Rx Cnt Ov */
+ XMR_64B_OV = 1<<26, /* Bit 26: 64 Byte Rx Cnt Ov */
+ XMR_UTIL_OV = 1<<25, /* Bit 25: Rx Util Cnt Overflow */
+ XMR_UTIL_UR = 1<<24, /* Bit 24: Rx Util Cnt Underrun */
+ XMR_CEX_ERR_OV = 1<<23, /* Bit 23: CEXT Err Cnt Ov */
+ XMR_FCS_ERR_OV = 1<<21, /* Bit 21: Rx FCS Error Cnt Ov */
+ XMR_LNG_ERR_OV = 1<<20, /* Bit 20: Rx too Long Err Cnt Ov*/
+ XMR_RUNT_OV = 1<<19, /* Bit 19: Runt Event Cnt Ov */
+ XMR_SHT_ERR_OV = 1<<18, /* Bit 18: Rx Short Ev Err Cnt Ov*/
+ XMR_SYM_ERR_OV = 1<<17, /* Bit 17: Rx Sym Err Cnt Ov */
+ XMR_CAR_ERR_OV = 1<<15, /* Bit 15: Rx Carr Ev Err Cnt Ov */
+ XMR_JAB_PKT_OV = 1<<14, /* Bit 14: Rx Jabb Packet Cnt Ov */
+ XMR_FIFO_OV = 1<<13, /* Bit 13: Rx FIFO Ov Ev Cnt Ov */
+ XMR_FRA_ERR_OV = 1<<12, /* Bit 12: Rx Framing Err Cnt Ov */
+ XMR_FMISS_OV = 1<<11, /* Bit 11: Rx Missed Ev Cnt Ov */
+ XMR_BURST = 1<<10, /* Bit 10: Rx Burst Event Cnt Ov */
+ XMR_INV_MOC = 1<<9, /* Bit 9: Rx with inv. MAC OC Ov*/
+ XMR_INV_MP = 1<<8, /* Bit 8: Rx inv Pause Frame Ov */
+ XMR_MCTRL_OV = 1<<7, /* Bit 7: Rx MAC Ctrl-F Cnt Ov */
+ XMR_MPAUSE_OV = 1<<6, /* Bit 6: Rx Pause MAC Ctrl-F Ov*/
+ XMR_UC_OK_OV = 1<<5, /* Bit 5: Rx Unicast Frame CntOv*/
+ XMR_MC_OK_OV = 1<<4, /* Bit 4: Rx Multicast Cnt Ov */
+ XMR_BC_OK_OV = 1<<3, /* Bit 3: Rx Broadcast Cnt Ov */
+ XMR_OK_LO_OV = 1<<2, /* Bit 2: Octets Rx OK Low CntOv*/
+ XMR_OK_HI_OV = 1<<1, /* Bit 1: Octets Rx OK Hi Cnt Ov*/
+ XMR_OK_OV = 1<<0, /* Bit 0: Frames Received Ok Ov */
+};
+
+#define XMR_DEF_MSK (XMR_OK_LO_OV | XMR_OK_HI_OV)
+
+/* XM_TX_CNT_EV 32 bit r/o Tx Counter Event Register */
+/* XM_TX_EV_MSK 32 bit r/w Tx Counter Event Mask */
+enum {
+ XMT_MAX_SZ_OV = 1<<25, /* Bit 25: 1024-MaxSize Tx Cnt Ov*/
+ XMT_1023B_OV = 1<<24, /* Bit 24: 512-1023Byte Tx Cnt Ov*/
+ XMT_511B_OV = 1<<23, /* Bit 23: 256-511 Byte Tx Cnt Ov*/
+ XMT_255B_OV = 1<<22, /* Bit 22: 128-255 Byte Tx Cnt Ov*/
+ XMT_127B_OV = 1<<21, /* Bit 21: 65-127 Byte Tx Cnt Ov */
+ XMT_64B_OV = 1<<20, /* Bit 20: 64 Byte Tx Cnt Ov */
+ XMT_UTIL_OV = 1<<19, /* Bit 19: Tx Util Cnt Overflow */
+ XMT_UTIL_UR = 1<<18, /* Bit 18: Tx Util Cnt Underrun */
+ XMT_CS_ERR_OV = 1<<17, /* Bit 17: Tx Carr Sen Err Cnt Ov*/
+ XMT_FIFO_UR_OV = 1<<16, /* Bit 16: Tx FIFO Ur Ev Cnt Ov */
+ XMT_EX_DEF_OV = 1<<15, /* Bit 15: Tx Ex Deferall Cnt Ov */
+ XMT_DEF = 1<<14, /* Bit 14: Tx Deferred Cnt Ov */
+ XMT_LAT_COL_OV = 1<<13, /* Bit 13: Tx Late Col Cnt Ov */
+ XMT_ABO_COL_OV = 1<<12, /* Bit 12: Tx abo dueto Ex Col Ov*/
+ XMT_MUL_COL_OV = 1<<11, /* Bit 11: Tx Mult Col Cnt Ov */
+ XMT_SNG_COL = 1<<10, /* Bit 10: Tx Single Col Cnt Ov */
+ XMT_MCTRL_OV = 1<<9, /* Bit 9: Tx MAC Ctrl Counter Ov*/
+ XMT_MPAUSE = 1<<8, /* Bit 8: Tx Pause MAC Ctrl-F Ov*/
+ XMT_BURST = 1<<7, /* Bit 7: Tx Burst Event Cnt Ov */
+ XMT_LONG = 1<<6, /* Bit 6: Tx Long Frame Cnt Ov */
+ XMT_UC_OK_OV = 1<<5, /* Bit 5: Tx Unicast Cnt Ov */
+ XMT_MC_OK_OV = 1<<4, /* Bit 4: Tx Multicast Cnt Ov */
+ XMT_BC_OK_OV = 1<<3, /* Bit 3: Tx Broadcast Cnt Ov */
+ XMT_OK_LO_OV = 1<<2, /* Bit 2: Octets Tx OK Low CntOv*/
+ XMT_OK_HI_OV = 1<<1, /* Bit 1: Octets Tx OK Hi Cnt Ov*/
+ XMT_OK_OV = 1<<0, /* Bit 0: Frames Tx Ok Ov */
+};
+
+#define XMT_DEF_MSK (XMT_OK_LO_OV | XMT_OK_HI_OV)
+
+struct skge_rx_desc {
+ u32 control;
+ u32 next_offset;
+ u32 dma_lo;
+ u32 dma_hi;
+ u32 status;
+ u32 timestamp;
+ u16 csum2;
+ u16 csum1;
+ u16 csum2_start;
+ u16 csum1_start;
+};
+
+struct skge_tx_desc {
+ u32 control;
+ u32 next_offset;
+ u32 dma_lo;
+ u32 dma_hi;
+ u32 status;
+ u32 csum_offs;
+ u16 csum_write;
+ u16 csum_start;
+ u32 rsvd;
+};
+
+struct skge_element {
+ struct skge_element *next;
+ void *desc;
+ struct sk_buff *skb;
+ DECLARE_PCI_UNMAP_ADDR(mapaddr);
+ DECLARE_PCI_UNMAP_LEN(maplen);
+};
+
+struct skge_ring {
+ struct skge_element *to_clean;
+ struct skge_element *to_use;
+ struct skge_element *start;
+ unsigned long count;
+};
+
+
+struct skge_hw {
+ void __iomem *regs;
+ struct pci_dev *pdev;
+ u32 intr_mask;
+ struct net_device *dev[2];
+
+ u8 mac_cfg;
+ u8 chip_id;
+ u8 phy_type;
+ u8 pmd_type;
+ u16 phy_addr;
+
+ u32 ram_size;
+ u32 ram_offset;
+
+ struct tasklet_struct ext_tasklet;
+ spinlock_t phy_lock;
+};
+
+static inline int isdualport(const struct skge_hw *hw)
+{
+ return !(hw->mac_cfg & CFG_SNG_MAC);
+}
+
+static inline u8 chip_rev(const struct skge_hw *hw)
+{
+ return (hw->mac_cfg & CFG_CHIP_R_MSK) >> 4;
+}
+
+static inline int iscopper(const struct skge_hw *hw)
+{
+ return (hw->pmd_type == 'T');
+}
+
+enum {
+ FLOW_MODE_NONE = 0, /* No Flow-Control */
+ FLOW_MODE_LOC_SEND = 1, /* Local station sends PAUSE */
+ FLOW_MODE_REM_SEND = 2, /* Symmetric or just remote */
+ FLOW_MODE_SYMMETRIC = 3, /* Both stations may send PAUSE */
+};
+
+struct skge_port {
+ u32 msg_enable;
+ struct skge_hw *hw;
+ struct net_device *netdev;
+ int port;
+
+ spinlock_t tx_lock;
+ u32 tx_avail;
+ struct skge_ring tx_ring;
+ struct skge_ring rx_ring;
+
+ struct net_device_stats net_stats;
+
+ u8 rx_csum;
+ u8 blink_on;
+ u8 flow_control;
+ u8 wol;
+ u8 autoneg; /* AUTONEG_ENABLE, AUTONEG_DISABLE */
+ u8 duplex; /* DUPLEX_HALF, DUPLEX_FULL */
+ u16 speed; /* SPEED_1000, SPEED_100, ... */
+ u32 advertising;
+
+ void *mem; /* PCI memory for rings */
+ dma_addr_t dma;
+ unsigned long mem_size;
+
+ struct timer_list link_check;
+ struct timer_list led_blink;
+};
+
+
+/* Register accessor for memory mapped device */
+static inline u32 skge_read32(const struct skge_hw *hw, int reg)
+{
+ return readl(hw->regs + reg);
+
+}
+
+static inline u16 skge_read16(const struct skge_hw *hw, int reg)
+{
+ return readw(hw->regs + reg);
+}
+
+static inline u8 skge_read8(const struct skge_hw *hw, int reg)
+{
+ return readb(hw->regs + reg);
+}
+
+static inline void skge_write32(const struct skge_hw *hw, int reg, u32 val)
+{
+ writel(val, hw->regs + reg);
+}
+
+static inline void skge_write16(const struct skge_hw *hw, int reg, u16 val)
+{
+ writew(val, hw->regs + reg);
+}
+
+static inline void skge_write8(const struct skge_hw *hw, int reg, u8 val)
+{
+ writeb(val, hw->regs + reg);
+}
+
+/* MAC Related Registers inside the device. */
+#define SKGEMAC_REG(port,reg) (((port)<<7)+(reg))
+
+/* PCI config space can be accessed via memory mapped space */
+#define SKGEPCI_REG(reg) ((reg)+ 0x380)
+
+#define SKGEXM_REG(port, reg) \
+ ((BASE_XMAC_1 + (port) * (BASE_XMAC_2 - BASE_XMAC_1)) | (reg) << 1)
+
+static inline u32 skge_xm_read32(const struct skge_hw *hw, int port, int reg)
+{
+ return skge_read32(hw, SKGEXM_REG(port,reg));
+}
+
+static inline u16 skge_xm_read16(const struct skge_hw *hw, int port, int reg)
+{
+ return skge_read16(hw, SKGEXM_REG(port,reg));
+}
+
+static inline u8 skge_xm_read8(const struct skge_hw *hw, int port, int reg)
+{
+ return skge_read8(hw, SKGEXM_REG(port,reg));
+}
+
+static inline void skge_xm_write32(const struct skge_hw *hw, int port, int r, u32 v)
+{
+ skge_write32(hw, SKGEXM_REG(port,r), v);
+}
+
+static inline void skge_xm_write16(const struct skge_hw *hw, int port, int r, u16 v)
+{
+ skge_write16(hw, SKGEXM_REG(port,r), v);
+}
+
+static inline void skge_xm_write8(const struct skge_hw *hw, int port, int r, u8 v)
+{
+ skge_write8(hw, SKGEXM_REG(port,r), v);
+}
+
+static inline void skge_xm_outhash(const struct skge_hw *hw, int port, int reg,
+ const u8 *hash)
+{
+ skge_xm_write16(hw, port, reg,
+ (u16)hash[0] | ((u16)hash[1] << 8));
+ skge_xm_write16(hw, port, reg+2,
+ (u16)hash[2] | ((u16)hash[3] << 8));
+ skge_xm_write16(hw, port, reg+4,
+ (u16)hash[4] | ((u16)hash[5] << 8));
+ skge_xm_write16(hw, port, reg+6,
+ (u16)hash[6] | ((u16)hash[7] << 8));
+}
+
+static inline void skge_xm_outaddr(const struct skge_hw *hw, int port, int reg,
+ const u8 *addr)
+{
+ skge_xm_write16(hw, port, reg,
+ (u16)addr[0] | ((u16)addr[1] << 8));
+ skge_xm_write16(hw, port, reg,
+ (u16)addr[2] | ((u16)addr[3] << 8));
+ skge_xm_write16(hw, port, reg,
+ (u16)addr[4] | ((u16)addr[5] << 8));
+}
+
+
+#define SKGEGMA_REG(port,reg) \
+ ((reg) + BASE_GMAC_1 + \
+ (port) * (BASE_GMAC_2-BASE_GMAC_1))
+
+static inline u16 skge_gma_read16(const struct skge_hw *hw, int port, int reg)
+{
+ return skge_read16(hw, SKGEGMA_REG(port,reg));
+}
+
+static inline u32 skge_gma_read32(const struct skge_hw *hw, int port, int reg)
+{
+ return (u32) skge_read16(hw, SKGEGMA_REG(port,reg))
+ | ((u32)skge_read16(hw, SKGEGMA_REG(port,reg+4)) << 16);
+}
+
+static inline u8 skge_gma_read8(const struct skge_hw *hw, int port, int reg)
+{
+ return skge_read8(hw, SKGEGMA_REG(port,reg));
+}
+
+static inline void skge_gma_write16(const struct skge_hw *hw, int port, int r, u16 v)
+{
+ skge_write16(hw, SKGEGMA_REG(port,r), v);
+}
+
+static inline void skge_gma_write32(const struct skge_hw *hw, int port, int r, u32 v)
+{
+ skge_write16(hw, SKGEGMA_REG(port, r), (u16) v);
+ skge_write32(hw, SKGEGMA_REG(port, r+4), (u16)(v >> 16));
+}
+
+static inline void skge_gma_write8(const struct skge_hw *hw, int port, int r, u8 v)
+{
+ skge_write8(hw, SKGEGMA_REG(port,r), v);
+}
+
+static inline void skge_gm_set_addr(struct skge_hw *hw, int port, int reg,
+ const u8 *addr)
+{
+ skge_gma_write16(hw, port, reg,
+ (u16) addr[0] | ((u16) addr[1] << 8));
+ skge_gma_write16(hw, port, reg+4,
+ (u16) addr[2] | ((u16) addr[3] << 8));
+ skge_gma_write16(hw, port, reg+8,
+ (u16) addr[4] | ((u16) addr[5] << 8));
+}
+
+#endif
git://bbs.cooldavid.org / net-next-2.6.git / commitdiff