b43: N-PHY: update init code to match current specs

Previous init path was based on old specs from old driver. Update it
as much as possible leaving some TODOs for not implemented functions.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

diff --git a/drivers/net/wireless/b43/phy_n.c b/drivers/net/wireless/b43/phy_n.c
index cb784a2504a6f19f7184aecf7bf8ec3ff301eadc..c16c98538f65fdba7768a94b9d7b642addd676d9 100644 (file)
--- a/drivers/net/wireless/b43/phy_n.c
+++ b/drivers/net/wireless/b43/phy_n.c
@@ -419,75 +419,196 @@ static void b43_nphy_rssi_cal(struct b43_wldev *dev, u8 type)
        //TODO
 }
 
+/*
+ * Init N-PHY
+ * http://bcm-v4.sipsolutions.net/802.11/PHY/Init/N
+ */
 int b43_phy_initn(struct b43_wldev *dev)
 {
+       struct ssb_bus *bus = dev->dev->bus;
        struct b43_phy *phy = &dev->phy;
+       struct b43_phy_n *nphy = phy->n;
+       u8 tx_pwr_state;
+       struct nphy_txgains target;
        u16 tmp;
+       enum ieee80211_band tmp2;
+       bool do_rssi_cal;
+
+       u16 clip[2];
+       bool do_cal = false;
 
-       //TODO: Spectral management
+       if ((dev->phy.rev >= 3) &&
+          (bus->sprom.boardflags_lo & B43_BFL_EXTLNA) &&
+          (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ)) {
+               chipco_set32(&dev->dev->bus->chipco, SSB_CHIPCO_CHIPCTL, 0x40);
+       }
+       nphy->deaf_count = 0;
        b43_nphy_tables_init(dev);
+       nphy->crsminpwr_adjusted = false;
+       nphy->noisevars_adjusted = false;
 
        /* Clear all overrides */
-       b43_phy_write(dev, B43_NPHY_RFCTL_OVER, 0);
+       if (dev->phy.rev >= 3) {
+               b43_phy_write(dev, B43_NPHY_TXF_40CO_B1S1, 0);
+               b43_phy_write(dev, B43_NPHY_RFCTL_OVER, 0);
+               b43_phy_write(dev, B43_NPHY_TXF_40CO_B1S0, 0);
+               b43_phy_write(dev, B43_NPHY_TXF_40CO_B32S1, 0);
+       } else {
+               b43_phy_write(dev, B43_NPHY_RFCTL_OVER, 0);
+       }
        b43_phy_write(dev, B43_NPHY_RFCTL_INTC1, 0);
        b43_phy_write(dev, B43_NPHY_RFCTL_INTC2, 0);
-       b43_phy_write(dev, B43_NPHY_RFCTL_INTC3, 0);
-       b43_phy_write(dev, B43_NPHY_RFCTL_INTC4, 0);
+       if (dev->phy.rev < 6) {
+               b43_phy_write(dev, B43_NPHY_RFCTL_INTC3, 0);
+               b43_phy_write(dev, B43_NPHY_RFCTL_INTC4, 0);
+       }
        b43_phy_mask(dev, B43_NPHY_RFSEQMODE,
                     ~(B43_NPHY_RFSEQMODE_CAOVER |
                       B43_NPHY_RFSEQMODE_TROVER));
+       if (dev->phy.rev >= 3)
+               b43_phy_write(dev, B43_NPHY_AFECTL_OVER1, 0);
        b43_phy_write(dev, B43_NPHY_AFECTL_OVER, 0);
 
-       tmp = (phy->rev < 2) ? 64 : 59;
-       b43_phy_maskset(dev, B43_NPHY_BPHY_CTL3,
-                       ~B43_NPHY_BPHY_CTL3_SCALE,
-                       tmp << B43_NPHY_BPHY_CTL3_SCALE_SHIFT);
-
+       if (dev->phy.rev <= 2) {
+               tmp = (dev->phy.rev == 2) ? 0x3B : 0x40;
+               b43_phy_maskset(dev, B43_NPHY_BPHY_CTL3,
+                               ~B43_NPHY_BPHY_CTL3_SCALE,
+                               tmp << B43_NPHY_BPHY_CTL3_SCALE_SHIFT);
+       }
        b43_phy_write(dev, B43_NPHY_AFESEQ_TX2RX_PUD_20M, 0x20);
        b43_phy_write(dev, B43_NPHY_AFESEQ_TX2RX_PUD_40M, 0x20);
 
-       b43_phy_write(dev, B43_NPHY_TXREALFD, 184);
-       b43_phy_write(dev, B43_NPHY_MIMO_CRSTXEXT, 200);
-       b43_phy_write(dev, B43_NPHY_PLOAD_CSENSE_EXTLEN, 80);
-       b43_phy_write(dev, B43_NPHY_C2_BCLIPBKOFF, 511);
+       if (bus->sprom.boardflags2_lo & 0x100 ||
+           (bus->boardinfo.vendor == PCI_VENDOR_ID_APPLE &&
+            bus->boardinfo.type == 0x8B))
+               b43_phy_write(dev, B43_NPHY_TXREALFD, 0xA0);
+       else
+               b43_phy_write(dev, B43_NPHY_TXREALFD, 0xB8);
+       b43_phy_write(dev, B43_NPHY_MIMO_CRSTXEXT, 0xC8);
+       b43_phy_write(dev, B43_NPHY_PLOAD_CSENSE_EXTLEN, 0x50);
+       b43_phy_write(dev, B43_NPHY_TXRIFS_FRDEL, 0x30);
 
-       //TODO MIMO-Config
-       //TODO Update TX/RX chain
+       /* TODO MIMO-Config */
+       /* TODO Update TX/RX chain */
 
        if (phy->rev < 2) {
                b43_phy_write(dev, B43_NPHY_DUP40_GFBL, 0xAA8);
                b43_phy_write(dev, B43_NPHY_DUP40_BL, 0x9A4);
        }
+
+       tmp2 = b43_current_band(dev->wl);
+       if ((nphy->ipa2g_on && tmp2 == IEEE80211_BAND_2GHZ) ||
+           (nphy->ipa5g_on && tmp2 == IEEE80211_BAND_5GHZ)) {
+               b43_phy_set(dev, B43_NPHY_PAPD_EN0, 0x1);
+               b43_phy_maskset(dev, B43_NPHY_EPS_TABLE_ADJ0, 0x007F,
+                               nphy->papd_epsilon_offset[0] << 7);
+               b43_phy_set(dev, B43_NPHY_PAPD_EN1, 0x1);
+               b43_phy_maskset(dev, B43_NPHY_EPS_TABLE_ADJ1, 0x007F,
+                               nphy->papd_epsilon_offset[1] << 7);
+               /* TODO N PHY IPA Set TX Dig Filters */
+       } else if (phy->rev >= 5) {
+               /* TODO N PHY Ext PA Set TX Dig Filters */
+       }
+
        b43_nphy_workarounds(dev);
-       b43_nphy_reset_cca(dev);
 
-       ssb_write32(dev->dev, SSB_TMSLOW,
-                   ssb_read32(dev->dev, SSB_TMSLOW) | B43_TMSLOW_MACPHYCLKEN);
+       /* Reset CCA, in init code it differs a little from standard way */
+       /* b43_nphy_bmac_clock_fgc(dev, 1); */
+       tmp = b43_phy_read(dev, B43_NPHY_BBCFG);
+       b43_phy_write(dev, B43_NPHY_BBCFG, tmp | B43_NPHY_BBCFG_RSTCCA);
+       b43_phy_write(dev, B43_NPHY_BBCFG, tmp & ~B43_NPHY_BBCFG_RSTCCA);
+       /* b43_nphy_bmac_clock_fgc(dev, 0); */
+
+       /* TODO N PHY MAC PHY Clock Set with argument 1 */
+
+       /* b43_nphy_pa_override(dev, false); */
        b43_nphy_force_rf_sequence(dev, B43_RFSEQ_RX2TX);
        b43_nphy_force_rf_sequence(dev, B43_RFSEQ_RESET2RX);
+       /* b43_nphy_pa_override(dev, true); */
+
+       /* b43_nphy_classifier(dev, 0, 0); */
+       /* b43_nphy_read_clip_detection(dev, clip); */
+       tx_pwr_state = nphy->txpwrctrl;
+       /* TODO N PHY TX power control with argument 0
+               (turning off power control) */
+       /* TODO Fix the TX Power Settings */
+       /* TODO N PHY TX Power Control Idle TSSI */
+       /* TODO N PHY TX Power Control Setup */
+
+       if (phy->rev >= 3) {
+               /* TODO */
+       } else {
+               /* TODO Write an N PHY table with ID 26, length 128, offset 192, width 32, and the data from Rev 2 TX Power Control Table */
+               /* TODO Write an N PHY table with ID 27, length 128, offset 192, width 32, and the data from Rev 2 TX Power Control Table */
+       }
 
-       b43_phy_read(dev, B43_NPHY_CLASSCTL); /* dummy read */
-       //TODO read core1/2 clip1 thres regs
-
-       if (1 /* FIXME Band is 2.4GHz */)
-               b43_nphy_bphy_init(dev);
-       //TODO disable TX power control
-       //TODO Fix the TX power settings
-       //TODO Init periodic calibration with reason 3
-       b43_nphy_rssi_cal(dev, 2);
-       b43_nphy_rssi_cal(dev, 0);
-       b43_nphy_rssi_cal(dev, 1);
-       //TODO get TX gain
-       //TODO init superswitch
-       //TODO calibrate LO
-       //TODO idle TSSI TX pctl
-       //TODO TX power control power setup
-       //TODO table writes
-       //TODO TX power control coefficients
-       //TODO enable TX power control
-       //TODO control antenna selection
-       //TODO init radar detection
-       //TODO reset channel if changed
+       if (nphy->phyrxchain != 3)
+               ;/* TODO N PHY RX Core Set State with phyrxchain as argument */
+       if (nphy->mphase_cal_phase_id > 0)
+               ;/* TODO PHY Periodic Calibration Multi-Phase Restart */
+
+       do_rssi_cal = false;
+       if (phy->rev >= 3) {
+               if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ)
+                       do_rssi_cal = (nphy->rssical_chanspec_2G == 0);
+               else
+                       do_rssi_cal = (nphy->rssical_chanspec_5G == 0);
+
+               if (do_rssi_cal)
+                       ;/* b43_nphy_rssi_cal(dev); */
+               else
+                       ;/* b43_nphy_restore_rssi_cal(dev); */
+       } else {
+               /* b43_nphy_rssi_cal(dev); */
+       }
+
+       if (!((nphy->measure_hold & 0x6) != 0)) {
+               if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ)
+                       do_cal = (nphy->iqcal_chanspec_2G == 0);
+               else
+                       do_cal = (nphy->iqcal_chanspec_5G == 0);
+
+               if (nphy->mute)
+                       do_cal = false;
+
+               if (do_cal) {
+                       /* target = b43_nphy_get_tx_gains(dev); */
+
+                       if (nphy->antsel_type == 2)
+                               ;/*TODO NPHY Superswitch Init with argument 1*/
+                       if (nphy->perical != 2) {
+                               /* b43_nphy_rssi_cal(dev); */
+                               if (phy->rev >= 3) {
+                                       nphy->cal_orig_pwr_idx[0] =
+                                           nphy->txpwrindex[0].index_internal;
+                                       nphy->cal_orig_pwr_idx[1] =
+                                           nphy->txpwrindex[1].index_internal;
+                                       /* TODO N PHY Pre Calibrate TX Gain */
+                                       /*target = b43_nphy_get_tx_gains(dev)*/
+                               }
+                       }
+               }
+       }
+
+       /*
+       if (!b43_nphy_cal_tx_iq_lo(dev, target, true, false)) {
+               if (b43_nphy_cal_rx_iq(dev, target, 2, 0) == 0)
+                       Call N PHY Save Cal
+               else if (nphy->mphase_cal_phase_id == 0)
+                       N PHY Periodic Calibration with argument 3
+       } else {
+               b43_nphy_restore_cal(dev);
+       }
+       */
+
+       /* b43_nphy_tx_pwr_ctrl_coef_setup(dev); */
+       /* TODO N PHY TX Power Control Enable with argument tx_pwr_state */
+       b43_phy_write(dev, B43_NPHY_TXMACIF_HOLDOFF, 0x0015);
+       b43_phy_write(dev, B43_NPHY_TXMACDELAY, 0x0320);
+       if (phy->rev >= 3 && phy->rev <= 6)
+               b43_phy_write(dev, B43_NPHY_PLOAD_CSENSE_EXTLEN, 0x0014);
+       /* b43_nphy_tx_lp_fbw(dev); */
+       /* TODO N PHY Spur Workaround */
 
        b43err(dev->wl, "IEEE 802.11n devices are not supported, yet.\n");
        return 0;