*
* @SURVEY_INFO_NOISE_DBM: noise (in dBm) was filled in
* @SURVEY_INFO_IN_USE: channel is currently being used
+ * @SURVEY_INFO_CHANNEL_TIME: channel active time (in ms) was filled in
+ * @SURVEY_INFO_CHANNEL_TIME_BUSY: channel busy time was filled in
+ * @SURVEY_INFO_CHANNEL_TIME_EXT_BUSY: extension channel busy time was filled in
+ * @SURVEY_INFO_CHANNEL_TIME_RX: channel receive time was filled in
+ * @SURVEY_INFO_CHANNEL_TIME_TX: channel transmit time was filled in
*
* Used by the driver to indicate which info in &struct survey_info
* it has filled in during the get_survey().
enum survey_info_flags {
SURVEY_INFO_NOISE_DBM = 1<<0,
SURVEY_INFO_IN_USE = 1<<1,
+ SURVEY_INFO_CHANNEL_TIME = 1<<2,
+ SURVEY_INFO_CHANNEL_TIME_BUSY = 1<<3,
+ SURVEY_INFO_CHANNEL_TIME_EXT_BUSY = 1<<4,
+ SURVEY_INFO_CHANNEL_TIME_RX = 1<<5,
+ SURVEY_INFO_CHANNEL_TIME_TX = 1<<6,
};
/**
* @filled: bitflag of flags from &enum survey_info_flags
* @noise: channel noise in dBm. This and all following fields are
* optional
+ * @channel_time: amount of time in ms the radio spent on the channel
+ * @channel_time_busy: amount of time the primary channel was sensed busy
+ * @channel_time_ext_busy: amount of time the extension channel was sensed busy
+ * @channel_time_rx: amount of time the radio spent receiving data
+ * @channel_time_tx: amount of time the radio spent transmitting data
*
* Used by dump_survey() to report back per-channel survey information.
*
*/
struct survey_info {
struct ieee80211_channel *channel;
+ u64 channel_time;
+ u64 channel_time_busy;
+ u64 channel_time_ext_busy;
+ u64 channel_time_rx;
+ u64 channel_time_tx;
u32 filled;
s8 noise;
};
* @STATION_INFO_TX_PACKETS: @tx_packets filled
* @STATION_INFO_TX_RETRIES: @tx_retries filled
* @STATION_INFO_TX_FAILED: @tx_failed filled
+ * @STATION_INFO_RX_DROP_MISC: @rx_dropped_misc filled
*/
enum station_info_flags {
STATION_INFO_INACTIVE_TIME = 1<<0,
STATION_INFO_TX_PACKETS = 1<<9,
STATION_INFO_TX_RETRIES = 1<<10,
STATION_INFO_TX_FAILED = 1<<11,
+ STATION_INFO_RX_DROP_MISC = 1<<12,
};
/**
* @tx_packets: packets transmitted to this station
* @tx_retries: cumulative retry counts
* @tx_failed: number of failed transmissions (retries exceeded, no ACK)
+ * @rx_dropped_misc: Dropped for un-specified reason.
* @generation: generation number for nl80211 dumps.
* This number should increase every time the list of stations
* changes, i.e. when a station is added or removed, so that
u32 tx_packets;
u32 tx_retries;
u32 tx_failed;
+ u32 rx_dropped_misc;
int generation;
};
* allows the driver to adjust the dynamic ps timeout value.
* @set_cqm_rssi_config: Configure connection quality monitor RSSI threshold.
*
+ * @mgmt_frame_register: Notify driver that a management frame type was
+ * registered. Note that this callback may not sleep, and cannot run
+ * concurrently with itself.
*/
struct cfg80211_ops {
int (*suspend)(struct wiphy *wiphy);
int (*get_tx_power)(struct wiphy *wiphy, int *dbm);
int (*set_wds_peer)(struct wiphy *wiphy, struct net_device *dev,
- u8 *addr);
+ const u8 *addr);
void (*rfkill_poll)(struct wiphy *wiphy);
int (*set_cqm_rssi_config)(struct wiphy *wiphy,
struct net_device *dev,
s32 rssi_thold, u32 rssi_hyst);
+
+ void (*mgmt_frame_register)(struct wiphy *wiphy,
+ struct net_device *dev,
+ u16 frame_type, bool reg);
};
/*
* initiator is %REGDOM_SET_BY_CORE).
* @WIPHY_FLAG_STRICT_REGULATORY: tells us the driver for this device will
* ignore regulatory domain settings until it gets its own regulatory
- * domain via its regulatory_hint(). After its gets its own regulatory
- * domain it will only allow further regulatory domain settings to
- * further enhance compliance. For example if channel 13 and 14 are
- * disabled by this regulatory domain no user regulatory domain can
- * enable these channels at a later time. This can be used for devices
- * which do not have calibration information gauranteed for frequencies
- * or settings outside of its regulatory domain.
+ * domain via its regulatory_hint() unless the regulatory hint is
+ * from a country IE. After its gets its own regulatory domain it will
+ * only allow further regulatory domain settings to further enhance
+ * compliance. For example if channel 13 and 14 are disabled by this
+ * regulatory domain no user regulatory domain can enable these channels
+ * at a later time. This can be used for devices which do not have
+ * calibration information guaranteed for frequencies or settings
+ * outside of its regulatory domain.
* @WIPHY_FLAG_DISABLE_BEACON_HINTS: enable this if your driver needs to ensure
* that passive scan flags and beaconing flags may not be lifted by
* cfg80211 due to regulatory beacon hints. For more information on beacon
WIPHY_FLAG_4ADDR_AP = BIT(5),
WIPHY_FLAG_4ADDR_STATION = BIT(6),
WIPHY_FLAG_CONTROL_PORT_PROTOCOL = BIT(7),
- WIPHY_FLAG_IBSS_RSN = BIT(7),
+ WIPHY_FLAG_IBSS_RSN = BIT(8),
};
struct mac_address {