/*******************************************************************************
Intel PRO/1000 Linux driver
- Copyright(c) 1999 - 2008 Intel Corporation.
+ Copyright(c) 1999 - 2009 Intel Corporation.
This program is free software; you can redistribute it and/or modify it
under the terms and conditions of the GNU General Public License,
*******************************************************************************/
-#include <linux/netdevice.h>
-#include <linux/ethtool.h>
-#include <linux/delay.h>
-#include <linux/pci.h>
-
#include "e1000.h"
enum e1000_mng_mode {
u32 i;
/* Setup the receive address */
- hw_dbg(hw, "Programming MAC Address into RAR[0]\n");
+ e_dbg("Programming MAC Address into RAR[0]\n");
e1000e_rar_set(hw, hw->mac.addr, 0);
/* Zero out the other (rar_entry_count - 1) receive addresses */
- hw_dbg(hw, "Clearing RAR[1-%u]\n", rar_count-1);
+ e_dbg("Clearing RAR[1-%u]\n", rar_count-1);
for (i = 1; i < rar_count; i++) {
E1000_WRITE_REG_ARRAY(hw, E1000_RA, (i << 1), 0);
e1e_flush();
for (; mc_addr_count > 0; mc_addr_count--) {
u32 hash_value, hash_reg, hash_bit, mta;
hash_value = e1000_hash_mc_addr(hw, mc_addr_list);
- hw_dbg(hw, "Hash value = 0x%03X\n", hash_value);
+ e_dbg("Hash value = 0x%03X\n", hash_value);
hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1);
hash_bit = hash_value & 0x1F;
mta = (1 << hash_bit);
*/
ret_val = e1000e_config_fc_after_link_up(hw);
if (ret_val) {
- hw_dbg(hw, "Error configuring flow control\n");
+ e_dbg("Error configuring flow control\n");
}
return ret_val;
mac->autoneg_failed = 1;
return 0;
}
- hw_dbg(hw, "NOT RXing /C/, disable AutoNeg and force link.\n");
+ e_dbg("NOT RXing /C/, disable AutoNeg and force link.\n");
/* Disable auto-negotiation in the TXCW register */
ew32(TXCW, (mac->txcw & ~E1000_TXCW_ANE));
/* Configure Flow Control after forcing link up. */
ret_val = e1000e_config_fc_after_link_up(hw);
if (ret_val) {
- hw_dbg(hw, "Error configuring flow control\n");
+ e_dbg("Error configuring flow control\n");
return ret_val;
}
} else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
* and disable forced link in the Device Control register
* in an attempt to auto-negotiate with our link partner.
*/
- hw_dbg(hw, "RXing /C/, enable AutoNeg and stop forcing link.\n");
+ e_dbg("RXing /C/, enable AutoNeg and stop forcing link.\n");
ew32(TXCW, mac->txcw);
ew32(CTRL, (ctrl & ~E1000_CTRL_SLU));
mac->autoneg_failed = 1;
return 0;
}
- hw_dbg(hw, "NOT RXing /C/, disable AutoNeg and force link.\n");
+ e_dbg("NOT RXing /C/, disable AutoNeg and force link.\n");
/* Disable auto-negotiation in the TXCW register */
ew32(TXCW, (mac->txcw & ~E1000_TXCW_ANE));
/* Configure Flow Control after forcing link up. */
ret_val = e1000e_config_fc_after_link_up(hw);
if (ret_val) {
- hw_dbg(hw, "Error configuring flow control\n");
+ e_dbg("Error configuring flow control\n");
return ret_val;
}
} else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
* and disable forced link in the Device Control register
* in an attempt to auto-negotiate with our link partner.
*/
- hw_dbg(hw, "RXing /C/, enable AutoNeg and stop forcing link.\n");
+ e_dbg("RXing /C/, enable AutoNeg and stop forcing link.\n");
ew32(TXCW, mac->txcw);
ew32(CTRL, (ctrl & ~E1000_CTRL_SLU));
if (rxcw & E1000_RXCW_SYNCH) {
if (!(rxcw & E1000_RXCW_IV)) {
mac->serdes_has_link = true;
- hw_dbg(hw, "SERDES: Link up - forced.\n");
+ e_dbg("SERDES: Link up - forced.\n");
}
} else {
mac->serdes_has_link = false;
- hw_dbg(hw, "SERDES: Link down - force failed.\n");
+ e_dbg("SERDES: Link down - force failed.\n");
}
}
if (rxcw & E1000_RXCW_SYNCH) {
if (!(rxcw & E1000_RXCW_IV)) {
mac->serdes_has_link = true;
- hw_dbg(hw, "SERDES: Link up - autoneg "
+ e_dbg("SERDES: Link up - autoneg "
"completed sucessfully.\n");
} else {
mac->serdes_has_link = false;
- hw_dbg(hw, "SERDES: Link down - invalid"
+ e_dbg("SERDES: Link down - invalid"
"codewords detected in autoneg.\n");
}
} else {
mac->serdes_has_link = false;
- hw_dbg(hw, "SERDES: Link down - no sync.\n");
+ e_dbg("SERDES: Link down - no sync.\n");
}
} else {
mac->serdes_has_link = false;
- hw_dbg(hw, "SERDES: Link down - autoneg failed\n");
+ e_dbg("SERDES: Link down - autoneg failed\n");
}
}
ret_val = e1000_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &nvm_data);
if (ret_val) {
- hw_dbg(hw, "NVM Read Error\n");
+ e_dbg("NVM Read Error\n");
return ret_val;
}
*/
hw->fc.current_mode = hw->fc.requested_mode;
- hw_dbg(hw, "After fix-ups FlowControl is now = %x\n",
+ e_dbg("After fix-ups FlowControl is now = %x\n",
hw->fc.current_mode);
/* Call the necessary media_type subroutine to configure the link. */
* control is disabled, because it does not hurt anything to
* initialize these registers.
*/
- hw_dbg(hw, "Initializing the Flow Control address, type and timer regs\n");
+ e_dbg("Initializing the Flow Control address, type and timer regs\n");
ew32(FCT, FLOW_CONTROL_TYPE);
ew32(FCAH, FLOW_CONTROL_ADDRESS_HIGH);
ew32(FCAL, FLOW_CONTROL_ADDRESS_LOW);
txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
break;
default:
- hw_dbg(hw, "Flow control param set incorrectly\n");
+ e_dbg("Flow control param set incorrectly\n");
return -E1000_ERR_CONFIG;
break;
}
break;
}
if (i == FIBER_LINK_UP_LIMIT) {
- hw_dbg(hw, "Never got a valid link from auto-neg!!!\n");
+ e_dbg("Never got a valid link from auto-neg!!!\n");
mac->autoneg_failed = 1;
/*
* AutoNeg failed to achieve a link, so we'll call
*/
ret_val = mac->ops.check_for_link(hw);
if (ret_val) {
- hw_dbg(hw, "Error while checking for link\n");
+ e_dbg("Error while checking for link\n");
return ret_val;
}
mac->autoneg_failed = 0;
} else {
mac->autoneg_failed = 0;
- hw_dbg(hw, "Valid Link Found\n");
+ e_dbg("Valid Link Found\n");
}
return 0;
* then the link-up status bit will be set and the flow control enable
* bits (RFCE and TFCE) will be set according to their negotiated value.
*/
- hw_dbg(hw, "Auto-negotiation enabled\n");
+ e_dbg("Auto-negotiation enabled\n");
ew32(CTRL, ctrl);
e1e_flush();
(er32(CTRL) & E1000_CTRL_SWDPIN1)) {
ret_val = e1000_poll_fiber_serdes_link_generic(hw);
} else {
- hw_dbg(hw, "No signal detected\n");
+ e_dbg("No signal detected\n");
}
return 0;
* 3: Both Rx and Tx flow control (symmetric) is enabled.
* other: No other values should be possible at this point.
*/
- hw_dbg(hw, "hw->fc.current_mode = %u\n", hw->fc.current_mode);
+ e_dbg("hw->fc.current_mode = %u\n", hw->fc.current_mode);
switch (hw->fc.current_mode) {
case e1000_fc_none:
ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE);
break;
default:
- hw_dbg(hw, "Flow control param set incorrectly\n");
+ e_dbg("Flow control param set incorrectly\n");
return -E1000_ERR_CONFIG;
}
}
if (ret_val) {
- hw_dbg(hw, "Error forcing flow control settings\n");
+ e_dbg("Error forcing flow control settings\n");
return ret_val;
}
return ret_val;
if (!(mii_status_reg & MII_SR_AUTONEG_COMPLETE)) {
- hw_dbg(hw, "Copper PHY and Auto Neg "
+ e_dbg("Copper PHY and Auto Neg "
"has not completed.\n");
return ret_val;
}
*/
if (hw->fc.requested_mode == e1000_fc_full) {
hw->fc.current_mode = e1000_fc_full;
- hw_dbg(hw, "Flow Control = FULL.\r\n");
+ e_dbg("Flow Control = FULL.\r\n");
} else {
hw->fc.current_mode = e1000_fc_rx_pause;
- hw_dbg(hw, "Flow Control = "
+ e_dbg("Flow Control = "
"RX PAUSE frames only.\r\n");
}
}
(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
(mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
hw->fc.current_mode = e1000_fc_tx_pause;
- hw_dbg(hw, "Flow Control = Tx PAUSE frames only.\r\n");
+ e_dbg("Flow Control = Tx PAUSE frames only.\r\n");
}
/*
* For transmitting PAUSE frames ONLY.
!(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
(mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
hw->fc.current_mode = e1000_fc_rx_pause;
- hw_dbg(hw, "Flow Control = Rx PAUSE frames only.\r\n");
+ e_dbg("Flow Control = Rx PAUSE frames only.\r\n");
} else {
/*
* Per the IEEE spec, at this point flow control
* should be disabled.
*/
hw->fc.current_mode = e1000_fc_none;
- hw_dbg(hw, "Flow Control = NONE.\r\n");
+ e_dbg("Flow Control = NONE.\r\n");
}
/*
*/
ret_val = mac->ops.get_link_up_info(hw, &speed, &duplex);
if (ret_val) {
- hw_dbg(hw, "Error getting link speed and duplex\n");
+ e_dbg("Error getting link speed and duplex\n");
return ret_val;
}
*/
ret_val = e1000e_force_mac_fc(hw);
if (ret_val) {
- hw_dbg(hw, "Error forcing flow control settings\n");
+ e_dbg("Error forcing flow control settings\n");
return ret_val;
}
}
status = er32(STATUS);
if (status & E1000_STATUS_SPEED_1000) {
*speed = SPEED_1000;
- hw_dbg(hw, "1000 Mbs, ");
+ e_dbg("1000 Mbs, ");
} else if (status & E1000_STATUS_SPEED_100) {
*speed = SPEED_100;
- hw_dbg(hw, "100 Mbs, ");
+ e_dbg("100 Mbs, ");
} else {
*speed = SPEED_10;
- hw_dbg(hw, "10 Mbs, ");
+ e_dbg("10 Mbs, ");
}
if (status & E1000_STATUS_FD) {
*duplex = FULL_DUPLEX;
- hw_dbg(hw, "Full Duplex\n");
+ e_dbg("Full Duplex\n");
} else {
*duplex = HALF_DUPLEX;
- hw_dbg(hw, "Half Duplex\n");
+ e_dbg("Half Duplex\n");
}
return 0;
}
if (i == timeout) {
- hw_dbg(hw, "Driver can't access device - SMBI bit is set.\n");
+ e_dbg("Driver can't access device - SMBI bit is set.\n");
return -E1000_ERR_NVM;
}
if (i == timeout) {
/* Release semaphores */
e1000e_put_hw_semaphore(hw);
- hw_dbg(hw, "Driver can't access the NVM\n");
+ e_dbg("Driver can't access the NVM\n");
return -E1000_ERR_NVM;
}
}
if (i == AUTO_READ_DONE_TIMEOUT) {
- hw_dbg(hw, "Auto read by HW from NVM has not completed.\n");
+ e_dbg("Auto read by HW from NVM has not completed.\n");
return -E1000_ERR_RESET;
}
ret_val = e1000_read_nvm(hw, NVM_ID_LED_SETTINGS, 1, data);
if (ret_val) {
- hw_dbg(hw, "NVM Read Error\n");
+ e_dbg("NVM Read Error\n");
return ret_val;
}
}
if (!timeout) {
- hw_dbg(hw, "Master requests are pending.\n");
+ e_dbg("Master requests are pending.\n");
return -E1000_ERR_MASTER_REQUESTS_PENDING;
}
if (!timeout) {
eecd &= ~E1000_EECD_REQ;
ew32(EECD, eecd);
- hw_dbg(hw, "Could not acquire NVM grant\n");
+ e_dbg("Could not acquire NVM grant\n");
return -E1000_ERR_NVM;
}
}
if (!timeout) {
- hw_dbg(hw, "SPI NVM Status error\n");
+ e_dbg("SPI NVM Status error\n");
return -E1000_ERR_NVM;
}
}
*/
if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) ||
(words == 0)) {
- hw_dbg(hw, "nvm parameter(s) out of bounds\n");
+ e_dbg("nvm parameter(s) out of bounds\n");
return -E1000_ERR_NVM;
}
*/
if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) ||
(words == 0)) {
- hw_dbg(hw, "nvm parameter(s) out of bounds\n");
+ e_dbg("nvm parameter(s) out of bounds\n");
return -E1000_ERR_NVM;
}
- ret_val = nvm->ops.acquire_nvm(hw);
+ ret_val = nvm->ops.acquire(hw);
if (ret_val)
return ret_val;
ret_val = e1000_ready_nvm_eeprom(hw);
if (ret_val) {
- nvm->ops.release_nvm(hw);
+ nvm->ops.release(hw);
return ret_val;
}
}
msleep(10);
- nvm->ops.release_nvm(hw);
+ nvm->ops.release(hw);
return 0;
}
ret_val = e1000_read_nvm(hw, NVM_ALT_MAC_ADDR_PTR, 1,
&mac_addr_offset);
if (ret_val) {
- hw_dbg(hw, "NVM Read Error\n");
+ e_dbg("NVM Read Error\n");
return ret_val;
}
if (mac_addr_offset == 0xFFFF)
ret_val = e1000_read_nvm(hw, mac_addr_offset, 1,
&nvm_data);
if (ret_val) {
- hw_dbg(hw, "NVM Read Error\n");
+ e_dbg("NVM Read Error\n");
return ret_val;
}
if (nvm_data & 0x0001)
offset = mac_addr_offset + (i >> 1);
ret_val = e1000_read_nvm(hw, offset, 1, &nvm_data);
if (ret_val) {
- hw_dbg(hw, "NVM Read Error\n");
+ e_dbg("NVM Read Error\n");
return ret_val;
}
hw->mac.perm_addr[i] = (u8)(nvm_data & 0xFF);
for (i = 0; i < (NVM_CHECKSUM_REG + 1); i++) {
ret_val = e1000_read_nvm(hw, i, 1, &nvm_data);
if (ret_val) {
- hw_dbg(hw, "NVM Read Error\n");
+ e_dbg("NVM Read Error\n");
return ret_val;
}
checksum += nvm_data;
}
if (checksum != (u16) NVM_SUM) {
- hw_dbg(hw, "NVM Checksum Invalid\n");
+ e_dbg("NVM Checksum Invalid\n");
return -E1000_ERR_NVM;
}
for (i = 0; i < NVM_CHECKSUM_REG; i++) {
ret_val = e1000_read_nvm(hw, i, 1, &nvm_data);
if (ret_val) {
- hw_dbg(hw, "NVM Read Error while updating checksum.\n");
+ e_dbg("NVM Read Error while updating checksum.\n");
return ret_val;
}
checksum += nvm_data;
checksum = (u16) NVM_SUM - checksum;
ret_val = e1000_write_nvm(hw, NVM_CHECKSUM_REG, 1, &checksum);
if (ret_val)
- hw_dbg(hw, "NVM Write Error while updating checksum.\n");
+ e_dbg("NVM Write Error while updating checksum.\n");
return ret_val;
}
/* Check that the host interface is enabled. */
hicr = er32(HICR);
if ((hicr & E1000_HICR_EN) == 0) {
- hw_dbg(hw, "E1000_HOST_EN bit disabled.\n");
+ e_dbg("E1000_HOST_EN bit disabled.\n");
return -E1000_ERR_HOST_INTERFACE_COMMAND;
}
/* check the previous command is completed */
}
if (i == E1000_MNG_DHCP_COMMAND_TIMEOUT) {
- hw_dbg(hw, "Previous command timeout failed .\n");
+ e_dbg("Previous command timeout failed .\n");
return -E1000_ERR_HOST_INTERFACE_COMMAND;
}
ret_val = e1000_read_nvm(hw, NVM_PBA_OFFSET_0, 1, &nvm_data);
if (ret_val) {
- hw_dbg(hw, "NVM Read Error\n");
+ e_dbg("NVM Read Error\n");
return ret_val;
}
*pba_num = (u32)(nvm_data << 16);
ret_val = e1000_read_nvm(hw, NVM_PBA_OFFSET_1, 1, &nvm_data);
if (ret_val) {
- hw_dbg(hw, "NVM Read Error\n");
+ e_dbg("NVM Read Error\n");
return ret_val;
}
*pba_num |= nvm_data;
git://bbs.cooldavid.org / net-next-2.6.git / blobdiff