static int bnx2x_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
{
struct bnx2x *bp = netdev_priv(dev);
-
- cmd->supported = bp->port.supported;
- cmd->advertising = bp->port.advertising;
+ int cfg_idx = bnx2x_get_link_cfg_idx(bp);
+ /* Dual Media boards present all available port types */
+ cmd->supported = bp->port.supported[cfg_idx] |
+ (bp->port.supported[cfg_idx ^ 1] &
+ (SUPPORTED_TP | SUPPORTED_FIBRE));
+ cmd->advertising = bp->port.advertising[cfg_idx];
if ((bp->state == BNX2X_STATE_OPEN) &&
!(bp->flags & MF_FUNC_DIS) &&
cmd->speed = vn_max_rate;
}
} else {
- cmd->speed = -1;
- cmd->duplex = -1;
+ cmd->speed = bp->link_params.req_line_speed[cfg_idx];
+ cmd->duplex = bp->link_params.req_duplex[cfg_idx];
}
- if (bp->link_params.num_phys > 0) {
- if (bp->link_params.phy[bp->link_params.num_phys - 1].
- supported & SUPPORTED_FIBRE)
- cmd->port = PORT_FIBRE;
- else
- cmd->port = PORT_TP;
- } else
- DP(NETIF_MSG_LINK, "No media found\n");
+ if (bp->port.supported[cfg_idx] & SUPPORTED_TP)
+ cmd->port = PORT_TP;
+ else if (bp->port.supported[cfg_idx] & SUPPORTED_FIBRE)
+ cmd->port = PORT_FIBRE;
+ else
+ BNX2X_ERR("XGXS PHY Failure detected\n");
+
cmd->phy_address = bp->mdio.prtad;
cmd->transceiver = XCVR_INTERNAL;
- if (bp->link_params.req_line_speed == SPEED_AUTO_NEG)
+ if (bp->link_params.req_line_speed[cfg_idx] == SPEED_AUTO_NEG)
cmd->autoneg = AUTONEG_ENABLE;
else
cmd->autoneg = AUTONEG_DISABLE;
static int bnx2x_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
{
struct bnx2x *bp = netdev_priv(dev);
- u32 advertising;
+ u32 advertising, cfg_idx, old_multi_phy_config, new_multi_phy_config;
if (IS_E1HMF(bp))
return 0;
cmd->duplex, cmd->port, cmd->phy_address, cmd->transceiver,
cmd->autoneg, cmd->maxtxpkt, cmd->maxrxpkt);
+ cfg_idx = bnx2x_get_link_cfg_idx(bp);
+ old_multi_phy_config = bp->link_params.multi_phy_config;
+ switch (cmd->port) {
+ case PORT_TP:
+ if (bp->port.supported[cfg_idx] & SUPPORTED_TP)
+ break; /* no port change */
+
+ if (!(bp->port.supported[0] & SUPPORTED_TP ||
+ bp->port.supported[1] & SUPPORTED_TP)) {
+ DP(NETIF_MSG_LINK, "Unsupported port type\n");
+ return -EINVAL;
+ }
+ bp->link_params.multi_phy_config &=
+ ~PORT_HW_CFG_PHY_SELECTION_MASK;
+ if (bp->link_params.multi_phy_config &
+ PORT_HW_CFG_PHY_SWAPPED_ENABLED)
+ bp->link_params.multi_phy_config |=
+ PORT_HW_CFG_PHY_SELECTION_SECOND_PHY;
+ else
+ bp->link_params.multi_phy_config |=
+ PORT_HW_CFG_PHY_SELECTION_FIRST_PHY;
+ break;
+ case PORT_FIBRE:
+ if (bp->port.supported[cfg_idx] & SUPPORTED_FIBRE)
+ break; /* no port change */
+
+ if (!(bp->port.supported[0] & SUPPORTED_FIBRE ||
+ bp->port.supported[1] & SUPPORTED_FIBRE)) {
+ DP(NETIF_MSG_LINK, "Unsupported port type\n");
+ return -EINVAL;
+ }
+ bp->link_params.multi_phy_config &=
+ ~PORT_HW_CFG_PHY_SELECTION_MASK;
+ if (bp->link_params.multi_phy_config &
+ PORT_HW_CFG_PHY_SWAPPED_ENABLED)
+ bp->link_params.multi_phy_config |=
+ PORT_HW_CFG_PHY_SELECTION_FIRST_PHY;
+ else
+ bp->link_params.multi_phy_config |=
+ PORT_HW_CFG_PHY_SELECTION_SECOND_PHY;
+ break;
+ default:
+ DP(NETIF_MSG_LINK, "Unsupported port type\n");
+ return -EINVAL;
+ }
+ /* Save new config in case command complete successuly */
+ new_multi_phy_config = bp->link_params.multi_phy_config;
+ /* Get the new cfg_idx */
+ cfg_idx = bnx2x_get_link_cfg_idx(bp);
+ /* Restore old config in case command failed */
+ bp->link_params.multi_phy_config = old_multi_phy_config;
+ DP(NETIF_MSG_LINK, "cfg_idx = %x\n", cfg_idx);
+
if (cmd->autoneg == AUTONEG_ENABLE) {
- if (!(bp->port.supported & SUPPORTED_Autoneg)) {
+ if (!(bp->port.supported[cfg_idx] & SUPPORTED_Autoneg)) {
DP(NETIF_MSG_LINK, "Autoneg not supported\n");
return -EINVAL;
}
/* advertise the requested speed and duplex if supported */
- cmd->advertising &= bp->port.supported;
+ cmd->advertising &= bp->port.supported[cfg_idx];
- bp->link_params.req_line_speed = SPEED_AUTO_NEG;
- bp->link_params.req_duplex = DUPLEX_FULL;
- bp->port.advertising |= (ADVERTISED_Autoneg |
+ bp->link_params.req_line_speed[cfg_idx] = SPEED_AUTO_NEG;
+ bp->link_params.req_duplex[cfg_idx] = DUPLEX_FULL;
+ bp->port.advertising[cfg_idx] |= (ADVERTISED_Autoneg |
cmd->advertising);
} else { /* forced speed */
/* advertise the requested speed and duplex if supported */
- switch (cmd->speed) {
+ u32 speed = cmd->speed;
+ speed |= (cmd->speed_hi << 16);
+ switch (speed) {
case SPEED_10:
if (cmd->duplex == DUPLEX_FULL) {
- if (!(bp->port.supported &
+ if (!(bp->port.supported[cfg_idx] &
SUPPORTED_10baseT_Full)) {
DP(NETIF_MSG_LINK,
"10M full not supported\n");
advertising = (ADVERTISED_10baseT_Full |
ADVERTISED_TP);
} else {
- if (!(bp->port.supported &
+ if (!(bp->port.supported[cfg_idx] &
SUPPORTED_10baseT_Half)) {
DP(NETIF_MSG_LINK,
"10M half not supported\n");
case SPEED_100:
if (cmd->duplex == DUPLEX_FULL) {
- if (!(bp->port.supported &
+ if (!(bp->port.supported[cfg_idx] &
SUPPORTED_100baseT_Full)) {
DP(NETIF_MSG_LINK,
"100M full not supported\n");
advertising = (ADVERTISED_100baseT_Full |
ADVERTISED_TP);
} else {
- if (!(bp->port.supported &
+ if (!(bp->port.supported[cfg_idx] &
SUPPORTED_100baseT_Half)) {
DP(NETIF_MSG_LINK,
"100M half not supported\n");
return -EINVAL;
}
- if (!(bp->port.supported & SUPPORTED_1000baseT_Full)) {
+ if (!(bp->port.supported[cfg_idx] &
+ SUPPORTED_1000baseT_Full)) {
DP(NETIF_MSG_LINK, "1G full not supported\n");
return -EINVAL;
}
return -EINVAL;
}
- if (!(bp->port.supported & SUPPORTED_2500baseX_Full)) {
+ if (!(bp->port.supported[cfg_idx]
+ & SUPPORTED_2500baseX_Full)) {
DP(NETIF_MSG_LINK,
"2.5G full not supported\n");
return -EINVAL;
return -EINVAL;
}
- if (!(bp->port.supported & SUPPORTED_10000baseT_Full)) {
+ if (!(bp->port.supported[cfg_idx]
+ & SUPPORTED_10000baseT_Full)) {
DP(NETIF_MSG_LINK, "10G full not supported\n");
return -EINVAL;
}
break;
default:
- DP(NETIF_MSG_LINK, "Unsupported speed\n");
+ DP(NETIF_MSG_LINK, "Unsupported speed %d\n", speed);
return -EINVAL;
}
- bp->link_params.req_line_speed = cmd->speed;
- bp->link_params.req_duplex = cmd->duplex;
- bp->port.advertising = advertising;
+ bp->link_params.req_line_speed[cfg_idx] = speed;
+ bp->link_params.req_duplex[cfg_idx] = cmd->duplex;
+ bp->port.advertising[cfg_idx] = advertising;
}
DP(NETIF_MSG_LINK, "req_line_speed %d\n"
DP_LEVEL " req_duplex %d advertising 0x%x\n",
- bp->link_params.req_line_speed, bp->link_params.req_duplex,
- bp->port.advertising);
+ bp->link_params.req_line_speed[cfg_idx],
+ bp->link_params.req_duplex[cfg_idx],
+ bp->port.advertising[cfg_idx]);
+ /* Set new config */
+ bp->link_params.multi_phy_config = new_multi_phy_config;
if (netif_running(dev)) {
bnx2x_stats_handle(bp, STATS_EVENT_STOP);
bnx2x_link_set(bp);
struct ethtool_pauseparam *epause)
{
struct bnx2x *bp = netdev_priv(dev);
-
- epause->autoneg = (bp->link_params.req_flow_ctrl ==
- BNX2X_FLOW_CTRL_AUTO) &&
- (bp->link_params.req_line_speed == SPEED_AUTO_NEG);
+ int cfg_idx = bnx2x_get_link_cfg_idx(bp);
+ epause->autoneg = (bp->link_params.req_flow_ctrl[cfg_idx] ==
+ BNX2X_FLOW_CTRL_AUTO);
epause->rx_pause = ((bp->link_vars.flow_ctrl & BNX2X_FLOW_CTRL_RX) ==
BNX2X_FLOW_CTRL_RX);
struct ethtool_pauseparam *epause)
{
struct bnx2x *bp = netdev_priv(dev);
-
+ u32 cfg_idx = bnx2x_get_link_cfg_idx(bp);
if (IS_E1HMF(bp))
return 0;
DP_LEVEL " autoneg %d rx_pause %d tx_pause %d\n",
epause->cmd, epause->autoneg, epause->rx_pause, epause->tx_pause);
- bp->link_params.req_flow_ctrl = BNX2X_FLOW_CTRL_AUTO;
+ bp->link_params.req_flow_ctrl[cfg_idx] = BNX2X_FLOW_CTRL_AUTO;
if (epause->rx_pause)
- bp->link_params.req_flow_ctrl |= BNX2X_FLOW_CTRL_RX;
+ bp->link_params.req_flow_ctrl[cfg_idx] |= BNX2X_FLOW_CTRL_RX;
if (epause->tx_pause)
- bp->link_params.req_flow_ctrl |= BNX2X_FLOW_CTRL_TX;
+ bp->link_params.req_flow_ctrl[cfg_idx] |= BNX2X_FLOW_CTRL_TX;
- if (bp->link_params.req_flow_ctrl == BNX2X_FLOW_CTRL_AUTO)
- bp->link_params.req_flow_ctrl = BNX2X_FLOW_CTRL_NONE;
+ if (bp->link_params.req_flow_ctrl[cfg_idx] == BNX2X_FLOW_CTRL_AUTO)
+ bp->link_params.req_flow_ctrl[cfg_idx] = BNX2X_FLOW_CTRL_NONE;
if (epause->autoneg) {
- if (!(bp->port.supported & SUPPORTED_Autoneg)) {
+ if (!(bp->port.supported[cfg_idx] & SUPPORTED_Autoneg)) {
DP(NETIF_MSG_LINK, "autoneg not supported\n");
return -EINVAL;
}
- if (bp->link_params.req_line_speed == SPEED_AUTO_NEG)
- bp->link_params.req_flow_ctrl = BNX2X_FLOW_CTRL_AUTO;
+ if (bp->link_params.req_line_speed[cfg_idx] == SPEED_AUTO_NEG) {
+ bp->link_params.req_flow_ctrl[cfg_idx] =
+ BNX2X_FLOW_CTRL_AUTO;
+ }
}
DP(NETIF_MSG_LINK,
- "req_flow_ctrl 0x%x\n", bp->link_params.req_flow_ctrl);
+ "req_flow_ctrl 0x%x\n", bp->link_params.req_flow_ctrl[cfg_idx]);
if (netif_running(dev)) {
bnx2x_stats_handle(bp, STATS_EVENT_STOP);
return rc;
}
-static void bnx2x_wait_for_link(struct bnx2x *bp, u8 link_up)
+static void bnx2x_wait_for_link(struct bnx2x *bp, u8 link_up, u8 is_serdes)
{
int cnt = 1000;
if (link_up)
- while (bnx2x_link_test(bp) && cnt--)
+ while (bnx2x_link_test(bp, is_serdes) && cnt--)
msleep(10);
}
struct ethtool_test *etest, u64 *buf)
{
struct bnx2x *bp = netdev_priv(dev);
-
+ u8 is_serdes;
if (bp->recovery_state != BNX2X_RECOVERY_DONE) {
printk(KERN_ERR "Handling parity error recovery. Try again later\n");
etest->flags |= ETH_TEST_FL_FAILED;
/* offline tests are not supported in MF mode */
if (IS_E1HMF(bp))
etest->flags &= ~ETH_TEST_FL_OFFLINE;
+ is_serdes = (bp->link_vars.link_status & LINK_STATUS_SERDES_LINK) > 0;
if (etest->flags & ETH_TEST_FL_OFFLINE) {
int port = BP_PORT(bp);
/* disable input for TX port IF */
REG_WR(bp, NIG_REG_EGRESS_UMP0_IN_EN + port*4, 0);
- link_up = (bnx2x_link_test(bp) == 0);
+ link_up = bp->link_vars.link_up;
+
bnx2x_nic_unload(bp, UNLOAD_NORMAL);
bnx2x_nic_load(bp, LOAD_DIAG);
/* wait until link state is restored */
- bnx2x_wait_for_link(bp, link_up);
+ bnx2x_wait_for_link(bp, link_up, is_serdes);
if (bnx2x_test_registers(bp) != 0) {
buf[0] = 1;
bnx2x_nic_load(bp, LOAD_NORMAL);
/* wait until link state is restored */
- bnx2x_wait_for_link(bp, link_up);
+ bnx2x_wait_for_link(bp, link_up, is_serdes);
}
if (bnx2x_test_nvram(bp) != 0) {
buf[3] = 1;
etest->flags |= ETH_TEST_FL_FAILED;
}
if (bp->port.pmf)
- if (bnx2x_link_test(bp) != 0) {
+ if (bnx2x_link_test(bp, is_serdes) != 0) {
buf[5] = 1;
etest->flags |= ETH_TEST_FL_FAILED;
}
git://bbs.cooldavid.org / net-next-2.6.git / blobdiff