#include <linux/i2c.h>
#include <linux/kernel.h>
#include <linux/slab.h>
+#include <linux/vgaarb.h>
#include "drmP.h"
#include "intel_drv.h"
#include "i915_drm.h"
return true;
}
-void
-intel_wait_for_vblank(struct drm_device *dev)
+/**
+ * intel_wait_for_vblank - wait for vblank on a given pipe
+ * @dev: drm device
+ * @pipe: pipe to wait for
+ *
+ * Wait for vblank to occur on a given pipe. Needed for various bits of
+ * mode setting code.
+ */
+void intel_wait_for_vblank(struct drm_device *dev, int pipe)
{
- /* Wait for 20ms, i.e. one cycle at 50hz. */
- msleep(20);
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ int pipestat_reg = (pipe == 0 ? PIPEASTAT : PIPEBSTAT);
+
+ /* Clear existing vblank status. Note this will clear any other
+ * sticky status fields as well.
+ *
+ * This races with i915_driver_irq_handler() with the result
+ * that either function could miss a vblank event. Here it is not
+ * fatal, as we will either wait upon the next vblank interrupt or
+ * timeout. Generally speaking intel_wait_for_vblank() is only
+ * called during modeset at which time the GPU should be idle and
+ * should *not* be performing page flips and thus not waiting on
+ * vblanks...
+ * Currently, the result of us stealing a vblank from the irq
+ * handler is that a single frame will be skipped during swapbuffers.
+ */
+ I915_WRITE(pipestat_reg,
+ I915_READ(pipestat_reg) | PIPE_VBLANK_INTERRUPT_STATUS);
+
+ /* Wait for vblank interrupt bit to set */
+ if (wait_for((I915_READ(pipestat_reg) &
+ PIPE_VBLANK_INTERRUPT_STATUS),
+ 50, 0))
+ DRM_DEBUG_KMS("vblank wait timed out\n");
+}
+
+/*
+ * intel_wait_for_pipe_off - wait for pipe to turn off
+ * @dev: drm device
+ * @pipe: pipe to wait for
+ *
+ * After disabling a pipe, we can't wait for vblank in the usual way,
+ * spinning on the vblank interrupt status bit, since we won't actually
+ * see an interrupt when the pipe is disabled.
+ *
+ * On Gen4 and above:
+ * wait for the pipe register state bit to turn off
+ *
+ * Otherwise:
+ * wait for the display line value to settle (it usually
+ * ends up stopping at the start of the next frame).
+ *
+ */
+static void intel_wait_for_pipe_off(struct drm_device *dev, int pipe)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+
+ if (INTEL_INFO(dev)->gen >= 4) {
+ int pipeconf_reg = (pipe == 0 ? PIPEACONF : PIPEBCONF);
+
+ /* Wait for the Pipe State to go off */
+ if (wait_for((I915_READ(pipeconf_reg) & I965_PIPECONF_ACTIVE) == 0,
+ 100, 0))
+ DRM_DEBUG_KMS("pipe_off wait timed out\n");
+ } else {
+ u32 last_line;
+ int pipedsl_reg = (pipe == 0 ? PIPEADSL : PIPEBDSL);
+ unsigned long timeout = jiffies + msecs_to_jiffies(100);
+
+ /* Wait for the display line to settle */
+ do {
+ last_line = I915_READ(pipedsl_reg) & DSL_LINEMASK;
+ mdelay(5);
+ } while (((I915_READ(pipedsl_reg) & DSL_LINEMASK) != last_line) &&
+ time_after(timeout, jiffies));
+ if (time_after(jiffies, timeout))
+ DRM_DEBUG_KMS("pipe_off wait timed out\n");
+ }
}
/* Parameters have changed, update FBC info */
void i8xx_disable_fbc(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
- unsigned long timeout = jiffies + msecs_to_jiffies(1);
u32 fbc_ctl;
if (!I915_HAS_FBC(dev))
I915_WRITE(FBC_CONTROL, fbc_ctl);
/* Wait for compressing bit to clear */
- while (I915_READ(FBC_STATUS) & FBC_STAT_COMPRESSING) {
- if (time_after(jiffies, timeout)) {
- DRM_DEBUG_DRIVER("FBC idle timed out\n");
- break;
- }
- ; /* do nothing */
+ if (wait_for((I915_READ(FBC_STATUS) & FBC_STAT_COMPRESSING) == 0, 10, 0)) {
+ DRM_DEBUG_KMS("FBC idle timed out\n");
+ return;
}
- intel_wait_for_vblank(dev);
-
DRM_DEBUG_KMS("disabled FBC\n");
}
dpfc_ctl = I915_READ(DPFC_CONTROL);
dpfc_ctl &= ~DPFC_CTL_EN;
I915_WRITE(DPFC_CONTROL, dpfc_ctl);
- intel_wait_for_vblank(dev);
DRM_DEBUG_KMS("disabled FBC\n");
}
dpfc_ctl = I915_READ(ILK_DPFC_CONTROL);
dpfc_ctl &= ~DPFC_CTL_EN;
I915_WRITE(ILK_DPFC_CONTROL, dpfc_ctl);
- intel_wait_for_vblank(dev);
DRM_DEBUG_KMS("disabled FBC\n");
}
goto out_disable;
}
+ /* If the kernel debugger is active, always disable compression */
+ if (in_dbg_master())
+ goto out_disable;
+
if (intel_fbc_enabled(dev)) {
/* We can re-enable it in this case, but need to update pitch */
if ((fb->pitch > dev_priv->cfb_pitch) ||
return 0;
}
+/* Assume fb object is pinned & idle & fenced and just update base pointers */
static int
-intel_pipe_set_base(struct drm_crtc *crtc, int x, int y,
- struct drm_framebuffer *old_fb)
+intel_pipe_set_base_atomic(struct drm_crtc *crtc, struct drm_framebuffer *fb,
+ int x, int y)
{
struct drm_device *dev = crtc->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
- struct drm_i915_master_private *master_priv;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
struct intel_framebuffer *intel_fb;
struct drm_i915_gem_object *obj_priv;
struct drm_gem_object *obj;
- int pipe = intel_crtc->pipe;
int plane = intel_crtc->plane;
unsigned long Start, Offset;
int dspbase = (plane == 0 ? DSPAADDR : DSPBADDR);
int dsptileoff = (plane == 0 ? DSPATILEOFF : DSPBTILEOFF);
int dspcntr_reg = (plane == 0) ? DSPACNTR : DSPBCNTR;
u32 dspcntr;
- int ret;
-
- /* no fb bound */
- if (!crtc->fb) {
- DRM_DEBUG_KMS("No FB bound\n");
- return 0;
- }
switch (plane) {
case 0:
return -EINVAL;
}
- intel_fb = to_intel_framebuffer(crtc->fb);
+ intel_fb = to_intel_framebuffer(fb);
obj = intel_fb->obj;
obj_priv = to_intel_bo(obj);
- mutex_lock(&dev->struct_mutex);
- ret = intel_pin_and_fence_fb_obj(dev, obj);
- if (ret != 0) {
- mutex_unlock(&dev->struct_mutex);
- return ret;
- }
-
- ret = i915_gem_object_set_to_display_plane(obj);
- if (ret != 0) {
- i915_gem_object_unpin(obj);
- mutex_unlock(&dev->struct_mutex);
- return ret;
- }
-
dspcntr = I915_READ(dspcntr_reg);
/* Mask out pixel format bits in case we change it */
dspcntr &= ~DISPPLANE_PIXFORMAT_MASK;
- switch (crtc->fb->bits_per_pixel) {
+ switch (fb->bits_per_pixel) {
case 8:
dspcntr |= DISPPLANE_8BPP;
break;
case 16:
- if (crtc->fb->depth == 15)
+ if (fb->depth == 15)
dspcntr |= DISPPLANE_15_16BPP;
else
dspcntr |= DISPPLANE_16BPP;
break;
case 24:
case 32:
- if (crtc->fb->depth == 30)
- dspcntr |= DISPPLANE_32BPP_30BIT_NO_ALPHA;
- else
- dspcntr |= DISPPLANE_32BPP_NO_ALPHA;
+ dspcntr |= DISPPLANE_32BPP_NO_ALPHA;
break;
default:
DRM_ERROR("Unknown color depth\n");
- i915_gem_object_unpin(obj);
- mutex_unlock(&dev->struct_mutex);
return -EINVAL;
}
if (IS_I965G(dev)) {
I915_WRITE(dspcntr_reg, dspcntr);
Start = obj_priv->gtt_offset;
- Offset = y * crtc->fb->pitch + x * (crtc->fb->bits_per_pixel / 8);
+ Offset = y * fb->pitch + x * (fb->bits_per_pixel / 8);
DRM_DEBUG_KMS("Writing base %08lX %08lX %d %d %d\n",
- Start, Offset, x, y, crtc->fb->pitch);
- I915_WRITE(dspstride, crtc->fb->pitch);
+ Start, Offset, x, y, fb->pitch);
+ I915_WRITE(dspstride, fb->pitch);
if (IS_I965G(dev)) {
- I915_WRITE(dspbase, Offset);
- I915_READ(dspbase);
I915_WRITE(dspsurf, Start);
- I915_READ(dspsurf);
I915_WRITE(dsptileoff, (y << 16) | x);
+ I915_WRITE(dspbase, Offset);
} else {
I915_WRITE(dspbase, Start + Offset);
- I915_READ(dspbase);
}
+ POSTING_READ(dspbase);
- if ((IS_I965G(dev) || plane == 0))
+ if (IS_I965G(dev) || plane == 0)
intel_update_fbc(crtc, &crtc->mode);
- intel_wait_for_vblank(dev);
+ intel_wait_for_vblank(dev, intel_crtc->pipe);
+ intel_increase_pllclock(crtc, true);
+
+ return 0;
+}
+
+static int
+intel_pipe_set_base(struct drm_crtc *crtc, int x, int y,
+ struct drm_framebuffer *old_fb)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_master_private *master_priv;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ struct intel_framebuffer *intel_fb;
+ struct drm_i915_gem_object *obj_priv;
+ struct drm_gem_object *obj;
+ int pipe = intel_crtc->pipe;
+ int plane = intel_crtc->plane;
+ int ret;
+
+ /* no fb bound */
+ if (!crtc->fb) {
+ DRM_DEBUG_KMS("No FB bound\n");
+ return 0;
+ }
+
+ switch (plane) {
+ case 0:
+ case 1:
+ break;
+ default:
+ DRM_ERROR("Can't update plane %d in SAREA\n", plane);
+ return -EINVAL;
+ }
+
+ intel_fb = to_intel_framebuffer(crtc->fb);
+ obj = intel_fb->obj;
+ obj_priv = to_intel_bo(obj);
+
+ mutex_lock(&dev->struct_mutex);
+ ret = intel_pin_and_fence_fb_obj(dev, obj);
+ if (ret != 0) {
+ mutex_unlock(&dev->struct_mutex);
+ return ret;
+ }
+
+ ret = i915_gem_object_set_to_display_plane(obj);
+ if (ret != 0) {
+ i915_gem_object_unpin(obj);
+ mutex_unlock(&dev->struct_mutex);
+ return ret;
+ }
+
+ ret = intel_pipe_set_base_atomic(crtc, crtc->fb, x, y);
+ if (ret) {
+ i915_gem_object_unpin(obj);
+ mutex_unlock(&dev->struct_mutex);
+ return ret;
+ }
if (old_fb) {
intel_fb = to_intel_framebuffer(old_fb);
obj_priv = to_intel_bo(intel_fb->obj);
i915_gem_object_unpin(intel_fb->obj);
}
- intel_increase_pllclock(crtc, true);
mutex_unlock(&dev->struct_mutex);
return 0;
}
-/* Disable the VGA plane that we never use */
-static void i915_disable_vga (struct drm_device *dev)
-{
- struct drm_i915_private *dev_priv = dev->dev_private;
- u8 sr1;
- u32 vga_reg;
-
- if (HAS_PCH_SPLIT(dev))
- vga_reg = CPU_VGACNTRL;
- else
- vga_reg = VGACNTRL;
-
- if (I915_READ(vga_reg) & VGA_DISP_DISABLE)
- return;
-
- I915_WRITE8(VGA_SR_INDEX, 1);
- sr1 = I915_READ8(VGA_SR_DATA);
- I915_WRITE8(VGA_SR_DATA, sr1 | (1 << 5));
- udelay(100);
-
- I915_WRITE(vga_reg, VGA_DISP_DISABLE);
-}
-
-static void ironlake_disable_pll_edp (struct drm_crtc *crtc)
-{
- struct drm_device *dev = crtc->dev;
- struct drm_i915_private *dev_priv = dev->dev_private;
- u32 dpa_ctl;
-
- DRM_DEBUG_KMS("\n");
- dpa_ctl = I915_READ(DP_A);
- dpa_ctl &= ~DP_PLL_ENABLE;
- I915_WRITE(DP_A, dpa_ctl);
-}
-
-static void ironlake_enable_pll_edp (struct drm_crtc *crtc)
-{
- struct drm_device *dev = crtc->dev;
- struct drm_i915_private *dev_priv = dev->dev_private;
- u32 dpa_ctl;
-
- dpa_ctl = I915_READ(DP_A);
- dpa_ctl |= DP_PLL_ENABLE;
- I915_WRITE(DP_A, dpa_ctl);
- udelay(200);
-}
-
-
static void ironlake_set_pll_edp (struct drm_crtc *crtc, int clock)
{
struct drm_device *dev = crtc->dev;
int fdi_tx_reg = (pipe == 0) ? FDI_TXA_CTL : FDI_TXB_CTL;
int fdi_rx_reg = (pipe == 0) ? FDI_RXA_CTL : FDI_RXB_CTL;
int transconf_reg = (pipe == 0) ? TRANSACONF : TRANSBCONF;
- int pf_ctl_reg = (pipe == 0) ? PFA_CTL_1 : PFB_CTL_1;
- int pf_win_size = (pipe == 0) ? PFA_WIN_SZ : PFB_WIN_SZ;
- int pf_win_pos = (pipe == 0) ? PFA_WIN_POS : PFB_WIN_POS;
int cpu_htot_reg = (pipe == 0) ? HTOTAL_A : HTOTAL_B;
int cpu_hblank_reg = (pipe == 0) ? HBLANK_A : HBLANK_B;
int cpu_hsync_reg = (pipe == 0) ? HSYNC_A : HSYNC_B;
int trans_vsync_reg = (pipe == 0) ? TRANS_VSYNC_A : TRANS_VSYNC_B;
int trans_dpll_sel = (pipe == 0) ? 0 : 1;
u32 temp;
- int n;
u32 pipe_bpc;
temp = I915_READ(pipeconf_reg);
case DRM_MODE_DPMS_ON:
case DRM_MODE_DPMS_STANDBY:
case DRM_MODE_DPMS_SUSPEND:
- DRM_DEBUG_KMS("crtc %d dpms on\n", pipe);
+ DRM_DEBUG_KMS("crtc %d/%d dpms on\n", pipe, plane);
if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS)) {
temp = I915_READ(PCH_LVDS);
}
}
- if (HAS_eDP) {
- /* enable eDP PLL */
- ironlake_enable_pll_edp(crtc);
- } else {
+ if (!HAS_eDP) {
/* enable PCH FDI RX PLL, wait warmup plus DMI latency */
temp = I915_READ(fdi_rx_reg);
}
/* Enable panel fitting for LVDS */
- if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS)
- || HAS_eDP || intel_pch_has_edp(crtc)) {
- temp = I915_READ(pf_ctl_reg);
- I915_WRITE(pf_ctl_reg, temp | PF_ENABLE | PF_FILTER_MED_3x3);
-
- /* currently full aspect */
- I915_WRITE(pf_win_pos, 0);
-
- I915_WRITE(pf_win_size,
- (dev_priv->panel_fixed_mode->hdisplay << 16) |
- (dev_priv->panel_fixed_mode->vdisplay));
+ if (dev_priv->pch_pf_size &&
+ (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS)
+ || HAS_eDP || intel_pch_has_edp(crtc))) {
+ /* Force use of hard-coded filter coefficients
+ * as some pre-programmed values are broken,
+ * e.g. x201.
+ */
+ I915_WRITE(pipe ? PFB_CTL_1 : PFA_CTL_1,
+ PF_ENABLE | PF_FILTER_MED_3x3);
+ I915_WRITE(pipe ? PFB_WIN_POS : PFA_WIN_POS,
+ dev_priv->pch_pf_pos);
+ I915_WRITE(pipe ? PFB_WIN_SZ : PFA_WIN_SZ,
+ dev_priv->pch_pf_size);
}
/* Enable CPU pipe */
int reg;
reg = I915_READ(trans_dp_ctl);
- reg &= ~TRANS_DP_PORT_SEL_MASK;
- reg = TRANS_DP_OUTPUT_ENABLE |
- TRANS_DP_ENH_FRAMING;
+ reg &= ~(TRANS_DP_PORT_SEL_MASK |
+ TRANS_DP_SYNC_MASK);
+ reg |= (TRANS_DP_OUTPUT_ENABLE |
+ TRANS_DP_ENH_FRAMING);
if (crtc->mode.flags & DRM_MODE_FLAG_PHSYNC)
reg |= TRANS_DP_HSYNC_ACTIVE_HIGH;
I915_WRITE(transconf_reg, temp | TRANS_ENABLE);
I915_READ(transconf_reg);
- while ((I915_READ(transconf_reg) & TRANS_STATE_ENABLE) == 0)
- ;
-
+ if (wait_for(I915_READ(transconf_reg) & TRANS_STATE_ENABLE, 100, 1))
+ DRM_ERROR("failed to enable transcoder\n");
}
intel_crtc_load_lut(crtc);
intel_update_fbc(crtc, &crtc->mode);
+ break;
- break;
case DRM_MODE_DPMS_OFF:
- DRM_DEBUG_KMS("crtc %d dpms off\n", pipe);
+ DRM_DEBUG_KMS("crtc %d/%d dpms off\n", pipe, plane);
drm_vblank_off(dev, pipe);
/* Disable display plane */
dev_priv->display.disable_fbc)
dev_priv->display.disable_fbc(dev);
- i915_disable_vga(dev);
-
/* disable cpu pipe, disable after all planes disabled */
temp = I915_READ(pipeconf_reg);
if ((temp & PIPEACONF_ENABLE) != 0) {
I915_WRITE(pipeconf_reg, temp & ~PIPEACONF_ENABLE);
- I915_READ(pipeconf_reg);
- n = 0;
+
/* wait for cpu pipe off, pipe state */
- while ((I915_READ(pipeconf_reg) & I965_PIPECONF_ACTIVE) != 0) {
- n++;
- if (n < 60) {
- udelay(500);
- continue;
- } else {
- DRM_DEBUG_KMS("pipe %d off delay\n",
- pipe);
- break;
- }
- }
+ if (wait_for((I915_READ(pipeconf_reg) & I965_PIPECONF_ACTIVE) == 0, 50, 1))
+ DRM_ERROR("failed to turn off cpu pipe\n");
} else
DRM_DEBUG_KMS("crtc %d is disabled\n", pipe);
udelay(100);
/* Disable PF */
- temp = I915_READ(pf_ctl_reg);
- if ((temp & PF_ENABLE) != 0) {
- I915_WRITE(pf_ctl_reg, temp & ~PF_ENABLE);
- I915_READ(pf_ctl_reg);
- }
- I915_WRITE(pf_win_size, 0);
- POSTING_READ(pf_win_size);
-
+ I915_WRITE(pipe ? PFB_CTL_1 : PFA_CTL_1, 0);
+ I915_WRITE(pipe ? PFB_WIN_SZ : PFA_WIN_SZ, 0);
/* disable CPU FDI tx and PCH FDI rx */
temp = I915_READ(fdi_tx_reg);
temp = I915_READ(transconf_reg);
if ((temp & TRANS_ENABLE) != 0) {
I915_WRITE(transconf_reg, temp & ~TRANS_ENABLE);
- I915_READ(transconf_reg);
- n = 0;
+
/* wait for PCH transcoder off, transcoder state */
- while ((I915_READ(transconf_reg) & TRANS_STATE_ENABLE) != 0) {
- n++;
- if (n < 60) {
- udelay(500);
- continue;
- } else {
- DRM_DEBUG_KMS("transcoder %d off "
- "delay\n", pipe);
- break;
- }
- }
+ if (wait_for((I915_READ(transconf_reg) & TRANS_STATE_ENABLE) == 0, 50, 1))
+ DRM_ERROR("failed to disable transcoder\n");
}
temp = I915_READ(transconf_reg);
I915_WRITE(pch_dpll_reg, temp & ~DPLL_VCO_ENABLE);
I915_READ(pch_dpll_reg);
- if (HAS_eDP) {
- ironlake_disable_pll_edp(crtc);
- }
-
/* Switch from PCDclk to Rawclk */
temp = I915_READ(fdi_rx_reg);
temp &= ~FDI_SEL_PCDCLK;
case DRM_MODE_DPMS_ON:
case DRM_MODE_DPMS_STANDBY:
case DRM_MODE_DPMS_SUSPEND:
- intel_update_watermarks(dev);
-
/* Enable the DPLL */
temp = I915_READ(dpll_reg);
if ((temp & DPLL_VCO_ENABLE) == 0) {
intel_crtc_dpms_overlay(intel_crtc, true);
break;
case DRM_MODE_DPMS_OFF:
- intel_update_watermarks(dev);
-
/* Give the overlay scaler a chance to disable if it's on this pipe */
intel_crtc_dpms_overlay(intel_crtc, false);
drm_vblank_off(dev, pipe);
dev_priv->display.disable_fbc)
dev_priv->display.disable_fbc(dev);
- /* Disable the VGA plane that we never use */
- i915_disable_vga(dev);
-
/* Disable display plane */
temp = I915_READ(dspcntr_reg);
if ((temp & DISPLAY_PLANE_ENABLE) != 0) {
I915_READ(dspbase_reg);
}
- if (!IS_I9XX(dev)) {
- /* Wait for vblank for the disable to take effect */
- intel_wait_for_vblank(dev);
- }
-
/* Don't disable pipe A or pipe A PLLs if needed */
if (pipeconf_reg == PIPEACONF &&
- (dev_priv->quirks & QUIRK_PIPEA_FORCE))
+ (dev_priv->quirks & QUIRK_PIPEA_FORCE)) {
+ /* Wait for vblank for the disable to take effect */
+ intel_wait_for_vblank(dev, pipe);
goto skip_pipe_off;
+ }
/* Next, disable display pipes */
temp = I915_READ(pipeconf_reg);
I915_READ(pipeconf_reg);
}
- /* Wait for vblank for the disable to take effect. */
- intel_wait_for_vblank(dev);
+ /* Wait for the pipe to turn off */
+ intel_wait_for_pipe_off(dev, pipe);
temp = I915_READ(dpll_reg);
if ((temp & DPLL_VCO_ENABLE) != 0) {
/**
* Sets the power management mode of the pipe and plane.
- *
- * This code should probably grow support for turning the cursor off and back
- * on appropriately at the same time as we're turning the pipe off/on.
*/
static void intel_crtc_dpms(struct drm_crtc *crtc, int mode)
{
int pipe = intel_crtc->pipe;
bool enabled;
- dev_priv->display.dpms(crtc, mode);
+ if (intel_crtc->dpms_mode == mode)
+ return;
intel_crtc->dpms_mode = mode;
+ intel_crtc->cursor_on = mode == DRM_MODE_DPMS_ON;
+
+ /* When switching on the display, ensure that SR is disabled
+ * with multiple pipes prior to enabling to new pipe.
+ *
+ * When switching off the display, make sure the cursor is
+ * properly hidden prior to disabling the pipe.
+ */
+ if (mode == DRM_MODE_DPMS_ON)
+ intel_update_watermarks(dev);
+ else
+ intel_crtc_update_cursor(crtc);
+
+ dev_priv->display.dpms(crtc, mode);
+
+ if (mode == DRM_MODE_DPMS_ON)
+ intel_crtc_update_cursor(crtc);
+ else
+ intel_update_watermarks(dev);
if (!dev->primary->master)
return;
encoder_funcs->dpms(encoder, DRM_MODE_DPMS_ON);
}
+void intel_encoder_destroy(struct drm_encoder *encoder)
+{
+ struct intel_encoder *intel_encoder = enc_to_intel_encoder(encoder);
+
+ if (intel_encoder->ddc_bus)
+ intel_i2c_destroy(intel_encoder->ddc_bus);
+
+ if (intel_encoder->i2c_bus)
+ intel_i2c_destroy(intel_encoder->i2c_bus);
+
+ drm_encoder_cleanup(encoder);
+ kfree(intel_encoder);
+}
+
static bool intel_crtc_mode_fixup(struct drm_crtc *crtc,
struct drm_display_mode *mode,
struct drm_display_mode *adjusted_mode)
{
struct drm_device *dev = crtc->dev;
+
if (HAS_PCH_SPLIT(dev)) {
/* FDI link clock is fixed at 2.7G */
if (mode->clock * 3 > IRONLAKE_FDI_FREQ * 4)
return false;
}
+
+ /* XXX some encoders set the crtcinfo, others don't.
+ * Obviously we need some form of conflict resolution here...
+ */
+ if (adjusted_mode->crtc_htotal == 0)
+ drm_mode_set_crtcinfo(adjusted_mode, 0);
+
return true;
}
/* Don't promote wm_size to unsigned... */
if (wm_size > (long)wm->max_wm)
wm_size = wm->max_wm;
- if (wm_size <= 0) {
+ if (wm_size <= 0)
wm_size = wm->default_wm;
- DRM_ERROR("Insufficient FIFO for plane, expect flickering:"
- " entries required = %ld, available = %lu.\n",
- entries_required + wm->guard_size,
- wm->fifo_size);
- }
-
return wm_size;
}
unsigned long cursor_hpll_disable;
};
-static struct cxsr_latency cxsr_latency_table[] = {
+static const struct cxsr_latency cxsr_latency_table[] = {
{1, 0, 800, 400, 3382, 33382, 3983, 33983}, /* DDR2-400 SC */
{1, 0, 800, 667, 3354, 33354, 3807, 33807}, /* DDR2-667 SC */
{1, 0, 800, 800, 3347, 33347, 3763, 33763}, /* DDR2-800 SC */
{0, 1, 400, 800, 6042, 36042, 6584, 36584}, /* DDR3-800 SC */
};
-static struct cxsr_latency *intel_get_cxsr_latency(int is_desktop, int is_ddr3,
- int fsb, int mem)
+static const struct cxsr_latency *intel_get_cxsr_latency(int is_desktop,
+ int is_ddr3,
+ int fsb,
+ int mem)
{
+ const struct cxsr_latency *latency;
int i;
- struct cxsr_latency *latency;
if (fsb == 0 || mem == 0)
return NULL;
static void pineview_disable_cxsr(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
- u32 reg;
/* deactivate cxsr */
- reg = I915_READ(DSPFW3);
- reg &= ~(PINEVIEW_SELF_REFRESH_EN);
- I915_WRITE(DSPFW3, reg);
- DRM_INFO("Big FIFO is disabled\n");
+ I915_WRITE(DSPFW3, I915_READ(DSPFW3) & ~PINEVIEW_SELF_REFRESH_EN);
}
/*
int pixel_size)
{
struct drm_i915_private *dev_priv = dev->dev_private;
+ const struct cxsr_latency *latency;
u32 reg;
unsigned long wm;
- struct cxsr_latency *latency;
int sr_clock;
- latency = intel_get_cxsr_latency(IS_PINEVIEW_G(dev), dev_priv->is_ddr3,
+ latency = intel_get_cxsr_latency(IS_PINEVIEW_G(dev), dev_priv->is_ddr3,
dev_priv->fsb_freq, dev_priv->mem_freq);
if (!latency) {
DRM_DEBUG_KMS("Unknown FSB/MEM found, disable CxSR\n");
DRM_DEBUG_KMS("DSPFW3 register is %x\n", reg);
/* activate cxsr */
- reg = I915_READ(DSPFW3);
- reg |= PINEVIEW_SELF_REFRESH_EN;
- I915_WRITE(DSPFW3, reg);
+ I915_WRITE(DSPFW3,
+ I915_READ(DSPFW3) | PINEVIEW_SELF_REFRESH_EN);
DRM_DEBUG_KMS("Self-refresh is enabled\n");
} else {
pineview_disable_cxsr(dev);
int line_count;
int planea_htotal = 0, planeb_htotal = 0;
struct drm_crtc *crtc;
- struct intel_crtc *intel_crtc;
/* Need htotal for all active display plane */
list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
- intel_crtc = to_intel_crtc(crtc);
- if (crtc->enabled) {
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ if (intel_crtc->dpms_mode == DRM_MODE_DPMS_ON) {
if (intel_crtc->plane == 0)
planea_htotal = crtc->mode.htotal;
else
reg_value = I915_READ(WM1_LP_ILK);
reg_value &= ~(WM1_LP_LATENCY_MASK | WM1_LP_SR_MASK |
WM1_LP_CURSOR_MASK);
- reg_value |= WM1_LP_SR_EN |
- (ilk_sr_latency << WM1_LP_LATENCY_SHIFT) |
+ reg_value |= (ilk_sr_latency << WM1_LP_LATENCY_SHIFT) |
(sr_wm << WM1_LP_SR_SHIFT) | cursor_wm;
I915_WRITE(WM1_LP_ILK, reg_value);
{
struct drm_i915_private *dev_priv = dev->dev_private;
struct drm_crtc *crtc;
- struct intel_crtc *intel_crtc;
int sr_hdisplay = 0;
unsigned long planea_clock = 0, planeb_clock = 0, sr_clock = 0;
int enabled = 0, pixel_size = 0;
/* Get the clock config from both planes */
list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
- intel_crtc = to_intel_crtc(crtc);
- if (crtc->enabled) {
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ if (intel_crtc->dpms_mode == DRM_MODE_DPMS_ON) {
enabled++;
if (intel_crtc->plane == 0) {
DRM_DEBUG_KMS("plane A (pipe %d) clock: %d\n",
u32 dpll = 0, fp = 0, fp2 = 0, dspcntr, pipeconf;
bool ok, has_reduced_clock = false, is_sdvo = false, is_dvo = false;
bool is_crt = false, is_lvds = false, is_tv = false, is_dp = false;
- bool is_edp = false;
+ struct intel_encoder *has_edp_encoder = NULL;
struct drm_mode_config *mode_config = &dev->mode_config;
struct drm_encoder *encoder;
- struct intel_encoder *intel_encoder = NULL;
const intel_limit_t *limit;
int ret;
struct fdi_m_n m_n = {0};
drm_vblank_pre_modeset(dev, pipe);
list_for_each_entry(encoder, &mode_config->encoder_list, head) {
+ struct intel_encoder *intel_encoder;
- if (!encoder || encoder->crtc != crtc)
+ if (encoder->crtc != crtc)
continue;
intel_encoder = enc_to_intel_encoder(encoder);
-
switch (intel_encoder->type) {
case INTEL_OUTPUT_LVDS:
is_lvds = true;
is_dp = true;
break;
case INTEL_OUTPUT_EDP:
- is_edp = true;
+ has_edp_encoder = intel_encoder;
break;
}
int lane = 0, link_bw, bpp;
/* eDP doesn't require FDI link, so just set DP M/N
according to current link config */
- if (is_edp) {
+ if (has_edp_encoder) {
target_clock = mode->clock;
- intel_edp_link_config(intel_encoder,
- &lane, &link_bw);
+ intel_edp_link_config(has_edp_encoder,
+ &lane, &link_bw);
} else {
/* DP over FDI requires target mode clock
instead of link clock */
temp |= PIPE_8BPC;
else
temp |= PIPE_6BPC;
- } else if (is_edp || (is_dp && intel_pch_has_edp(crtc))) {
+ } else if (has_edp_encoder || (is_dp && intel_pch_has_edp(crtc))) {
switch (dev_priv->edp_bpp/3) {
case 8:
temp |= PIPE_8BPC;
udelay(200);
- if (is_edp) {
+ if (has_edp_encoder) {
if (dev_priv->lvds_use_ssc) {
temp |= DREF_SSC1_ENABLE;
I915_WRITE(PCH_DREF_CONTROL, temp);
dpll_reg = pch_dpll_reg;
}
- if (is_edp) {
- ironlake_disable_pll_edp(crtc);
- } else if ((dpll & DPLL_VCO_ENABLE)) {
+ if (!has_edp_encoder) {
I915_WRITE(fp_reg, fp);
I915_WRITE(dpll_reg, dpll & ~DPLL_VCO_ENABLE);
I915_READ(dpll_reg);
}
}
- if (!is_edp) {
+ if (!has_edp_encoder) {
I915_WRITE(fp_reg, fp);
I915_WRITE(dpll_reg, dpll);
I915_READ(dpll_reg);
I915_WRITE(link_m1_reg, m_n.link_m);
I915_WRITE(link_n1_reg, m_n.link_n);
- if (is_edp) {
+ if (has_edp_encoder) {
ironlake_set_pll_edp(crtc, adjusted_mode->clock);
} else {
/* enable FDI RX PLL too */
I915_WRITE(pipeconf_reg, pipeconf);
I915_READ(pipeconf_reg);
- intel_wait_for_vblank(dev);
+ intel_wait_for_vblank(dev, pipe);
if (IS_IRONLAKE(dev)) {
/* enable address swizzle for tiling buffer */
/* Flush the plane changes */
ret = intel_pipe_set_base(crtc, x, y, old_fb);
- if ((IS_I965G(dev) || plane == 0))
- intel_update_fbc(crtc, &crtc->mode);
-
intel_update_watermarks(dev);
drm_vblank_post_modeset(dev, pipe);
}
}
+static void i845_update_cursor(struct drm_crtc *crtc, u32 base)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ bool visible = base != 0;
+ u32 cntl;
+
+ if (intel_crtc->cursor_visible == visible)
+ return;
+
+ cntl = I915_READ(CURACNTR);
+ if (visible) {
+ /* On these chipsets we can only modify the base whilst
+ * the cursor is disabled.
+ */
+ I915_WRITE(CURABASE, base);
+
+ cntl &= ~(CURSOR_FORMAT_MASK);
+ /* XXX width must be 64, stride 256 => 0x00 << 28 */
+ cntl |= CURSOR_ENABLE |
+ CURSOR_GAMMA_ENABLE |
+ CURSOR_FORMAT_ARGB;
+ } else
+ cntl &= ~(CURSOR_ENABLE | CURSOR_GAMMA_ENABLE);
+ I915_WRITE(CURACNTR, cntl);
+
+ intel_crtc->cursor_visible = visible;
+}
+
+static void i9xx_update_cursor(struct drm_crtc *crtc, u32 base)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ int pipe = intel_crtc->pipe;
+ bool visible = base != 0;
+
+ if (intel_crtc->cursor_visible != visible) {
+ uint32_t cntl = I915_READ(pipe == 0 ? CURACNTR : CURBCNTR);
+ if (base) {
+ cntl &= ~(CURSOR_MODE | MCURSOR_PIPE_SELECT);
+ cntl |= CURSOR_MODE_64_ARGB_AX | MCURSOR_GAMMA_ENABLE;
+ cntl |= pipe << 28; /* Connect to correct pipe */
+ } else {
+ cntl &= ~(CURSOR_MODE | MCURSOR_GAMMA_ENABLE);
+ cntl |= CURSOR_MODE_DISABLE;
+ }
+ I915_WRITE(pipe == 0 ? CURACNTR : CURBCNTR, cntl);
+
+ intel_crtc->cursor_visible = visible;
+ }
+ /* and commit changes on next vblank */
+ I915_WRITE(pipe == 0 ? CURABASE : CURBBASE, base);
+}
+
/* If no-part of the cursor is visible on the framebuffer, then the GPU may hang... */
static void intel_crtc_update_cursor(struct drm_crtc *crtc)
{
int pipe = intel_crtc->pipe;
int x = intel_crtc->cursor_x;
int y = intel_crtc->cursor_y;
- uint32_t base, pos;
+ u32 base, pos;
bool visible;
pos = 0;
- if (crtc->fb) {
+ if (intel_crtc->cursor_on && crtc->fb) {
base = intel_crtc->cursor_addr;
if (x > (int) crtc->fb->width)
base = 0;
pos |= y << CURSOR_Y_SHIFT;
visible = base != 0;
- if (!visible && !intel_crtc->cursor_visble)
+ if (!visible && !intel_crtc->cursor_visible)
return;
I915_WRITE(pipe == 0 ? CURAPOS : CURBPOS, pos);
- if (intel_crtc->cursor_visble != visible) {
- uint32_t cntl = I915_READ(pipe == 0 ? CURACNTR : CURBCNTR);
- if (base) {
- /* Hooray for CUR*CNTR differences */
- if (IS_MOBILE(dev) || IS_I9XX(dev)) {
- cntl &= ~(CURSOR_MODE | MCURSOR_PIPE_SELECT);
- cntl |= CURSOR_MODE_64_ARGB_AX | MCURSOR_GAMMA_ENABLE;
- cntl |= pipe << 28; /* Connect to correct pipe */
- } else {
- cntl &= ~(CURSOR_FORMAT_MASK);
- cntl |= CURSOR_ENABLE;
- cntl |= CURSOR_FORMAT_ARGB | CURSOR_GAMMA_ENABLE;
- }
- } else {
- if (IS_MOBILE(dev) || IS_I9XX(dev)) {
- cntl &= ~(CURSOR_MODE | MCURSOR_GAMMA_ENABLE);
- cntl |= CURSOR_MODE_DISABLE;
- } else {
- cntl &= ~(CURSOR_ENABLE | CURSOR_GAMMA_ENABLE);
- }
- }
- I915_WRITE(pipe == 0 ? CURACNTR : CURBCNTR, cntl);
-
- intel_crtc->cursor_visble = visible;
- }
- /* and commit changes on next vblank */
- I915_WRITE(pipe == 0 ? CURABASE : CURBBASE, base);
+ if (IS_845G(dev) || IS_I865G(dev))
+ i845_update_cursor(crtc, base);
+ else
+ i9xx_update_cursor(crtc, base);
if (visible)
intel_mark_busy(dev, to_intel_framebuffer(crtc->fb)->obj);
addr = obj_priv->gtt_offset;
} else {
+ int align = IS_I830(dev) ? 16 * 1024 : 256;
ret = i915_gem_attach_phys_object(dev, bo,
- (intel_crtc->pipe == 0) ? I915_GEM_PHYS_CURSOR_0 : I915_GEM_PHYS_CURSOR_1);
+ (intel_crtc->pipe == 0) ? I915_GEM_PHYS_CURSOR_0 : I915_GEM_PHYS_CURSOR_1,
+ align);
if (ret) {
DRM_ERROR("failed to attach phys object\n");
goto fail_locked;
encoder_funcs->commit(encoder);
}
/* let the connector get through one full cycle before testing */
- intel_wait_for_vblank(dev);
+ intel_wait_for_vblank(dev, intel_crtc->pipe);
return crtc;
}
dpll &= ~DISPLAY_RATE_SELECT_FPA1;
I915_WRITE(dpll_reg, dpll);
dpll = I915_READ(dpll_reg);
- intel_wait_for_vblank(dev);
+ intel_wait_for_vblank(dev, pipe);
dpll = I915_READ(dpll_reg);
if (dpll & DISPLAY_RATE_SELECT_FPA1)
DRM_DEBUG_DRIVER("failed to upclock LVDS!\n");
dpll |= DISPLAY_RATE_SELECT_FPA1;
I915_WRITE(dpll_reg, dpll);
dpll = I915_READ(dpll_reg);
- intel_wait_for_vblank(dev);
+ intel_wait_for_vblank(dev, pipe);
dpll = I915_READ(dpll_reg);
if (!(dpll & DISPLAY_RATE_SELECT_FPA1))
DRM_DEBUG_DRIVER("failed to downclock LVDS!\n");
kfree(intel_crtc);
}
-struct intel_unpin_work {
- struct work_struct work;
- struct drm_device *dev;
- struct drm_gem_object *old_fb_obj;
- struct drm_gem_object *pending_flip_obj;
- struct drm_pending_vblank_event *event;
- int pending;
-};
-
static void intel_unpin_work_fn(struct work_struct *__work)
{
struct intel_unpin_work *work =
spin_lock_irqsave(&dev->event_lock, flags);
if (intel_crtc->unpin_work) {
- intel_crtc->unpin_work->pending = 1;
+ if ((++intel_crtc->unpin_work->pending) > 1)
+ DRM_ERROR("Prepared flip multiple times\n");
} else {
DRM_DEBUG_DRIVER("preparing flip with no unpin work?\n");
}
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
struct intel_unpin_work *work;
unsigned long flags, offset;
- int pipesrc_reg = (intel_crtc->pipe == 0) ? PIPEASRC : PIPEBSRC;
- int ret, pipesrc;
- u32 flip_mask;
+ int pipe = intel_crtc->pipe;
+ u32 pf, pipesrc;
+ int ret;
work = kzalloc(sizeof *work, GFP_KERNEL);
if (work == NULL)
atomic_inc(&obj_priv->pending_flip);
work->pending_flip_obj = obj;
- if (intel_crtc->plane)
- flip_mask = I915_DISPLAY_PLANE_B_FLIP_PENDING_INTERRUPT;
- else
- flip_mask = I915_DISPLAY_PLANE_A_FLIP_PENDING_INTERRUPT;
+ if (IS_GEN3(dev) || IS_GEN2(dev)) {
+ u32 flip_mask;
+
+ if (intel_crtc->plane)
+ flip_mask = MI_WAIT_FOR_PLANE_B_FLIP;
+ else
+ flip_mask = MI_WAIT_FOR_PLANE_A_FLIP;
+
+ BEGIN_LP_RING(2);
+ OUT_RING(MI_WAIT_FOR_EVENT | flip_mask);
+ OUT_RING(0);
+ ADVANCE_LP_RING();
+ }
- /* Wait for any previous flip to finish */
- if (IS_GEN3(dev))
- while (I915_READ(ISR) & flip_mask)
- ;
+ work->enable_stall_check = true;
/* Offset into the new buffer for cases of shared fbs between CRTCs */
- offset = obj_priv->gtt_offset;
- offset += (crtc->y * fb->pitch) + (crtc->x * (fb->bits_per_pixel) / 8);
+ offset = crtc->y * fb->pitch + crtc->x * fb->bits_per_pixel/8;
BEGIN_LP_RING(4);
- if (IS_I965G(dev)) {
+ switch(INTEL_INFO(dev)->gen) {
+ case 2:
OUT_RING(MI_DISPLAY_FLIP |
MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
OUT_RING(fb->pitch);
- OUT_RING(offset | obj_priv->tiling_mode);
- pipesrc = I915_READ(pipesrc_reg);
- OUT_RING(pipesrc & 0x0fff0fff);
- } else {
+ OUT_RING(obj_priv->gtt_offset + offset);
+ OUT_RING(MI_NOOP);
+ break;
+
+ case 3:
OUT_RING(MI_DISPLAY_FLIP_I915 |
MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
OUT_RING(fb->pitch);
- OUT_RING(offset);
+ OUT_RING(obj_priv->gtt_offset + offset);
OUT_RING(MI_NOOP);
+ break;
+
+ case 4:
+ case 5:
+ /* i965+ uses the linear or tiled offsets from the
+ * Display Registers (which do not change across a page-flip)
+ * so we need only reprogram the base address.
+ */
+ OUT_RING(MI_DISPLAY_FLIP |
+ MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
+ OUT_RING(fb->pitch);
+ OUT_RING(obj_priv->gtt_offset | obj_priv->tiling_mode);
+
+ /* XXX Enabling the panel-fitter across page-flip is so far
+ * untested on non-native modes, so ignore it for now.
+ * pf = I915_READ(pipe == 0 ? PFA_CTL_1 : PFB_CTL_1) & PF_ENABLE;
+ */
+ pf = 0;
+ pipesrc = I915_READ(pipe == 0 ? PIPEASRC : PIPEBSRC) & 0x0fff0fff;
+ OUT_RING(pf | pipesrc);
+ break;
+
+ case 6:
+ OUT_RING(MI_DISPLAY_FLIP |
+ MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
+ OUT_RING(fb->pitch | obj_priv->tiling_mode);
+ OUT_RING(obj_priv->gtt_offset);
+
+ pf = I915_READ(pipe == 0 ? PFA_CTL_1 : PFB_CTL_1) & PF_ENABLE;
+ pipesrc = I915_READ(pipe == 0 ? PIPEASRC : PIPEBSRC) & 0x0fff0fff;
+ OUT_RING(pf | pipesrc);
+ break;
}
ADVANCE_LP_RING();
.mode_fixup = intel_crtc_mode_fixup,
.mode_set = intel_crtc_mode_set,
.mode_set_base = intel_pipe_set_base,
+ .mode_set_base_atomic = intel_pipe_set_base_atomic,
.prepare = intel_crtc_prepare,
.commit = intel_crtc_commit,
.load_lut = intel_crtc_load_lut,
dev_priv->pipe_to_crtc_mapping[intel_crtc->pipe] = &intel_crtc->base;
intel_crtc->cursor_addr = 0;
- intel_crtc->dpms_mode = DRM_MODE_DPMS_OFF;
+ intel_crtc->dpms_mode = -1;
drm_crtc_helper_add(&intel_crtc->base, &intel_helper_funcs);
intel_crtc->busy = false;
};
static struct drm_gem_object *
-intel_alloc_power_context(struct drm_device *dev)
+intel_alloc_context_page(struct drm_device *dev)
{
- struct drm_gem_object *pwrctx;
+ struct drm_gem_object *ctx;
int ret;
- pwrctx = i915_gem_alloc_object(dev, 4096);
- if (!pwrctx) {
+ ctx = i915_gem_alloc_object(dev, 4096);
+ if (!ctx) {
DRM_DEBUG("failed to alloc power context, RC6 disabled\n");
return NULL;
}
mutex_lock(&dev->struct_mutex);
- ret = i915_gem_object_pin(pwrctx, 4096);
+ ret = i915_gem_object_pin(ctx, 4096);
if (ret) {
DRM_ERROR("failed to pin power context: %d\n", ret);
goto err_unref;
}
- ret = i915_gem_object_set_to_gtt_domain(pwrctx, 1);
+ ret = i915_gem_object_set_to_gtt_domain(ctx, 1);
if (ret) {
DRM_ERROR("failed to set-domain on power context: %d\n", ret);
goto err_unpin;
}
mutex_unlock(&dev->struct_mutex);
- return pwrctx;
+ return ctx;
err_unpin:
- i915_gem_object_unpin(pwrctx);
+ i915_gem_object_unpin(ctx);
err_unref:
- drm_gem_object_unreference(pwrctx);
+ drm_gem_object_unreference(ctx);
mutex_unlock(&dev->struct_mutex);
return NULL;
}
struct drm_i915_private *dev_priv = dev->dev_private;
u32 rgvmodectl = I915_READ(MEMMODECTL);
u8 fmax, fmin, fstart, vstart;
- int i = 0;
/* 100ms RC evaluation intervals */
I915_WRITE(RCUPEI, 100000);
rgvmodectl |= MEMMODE_SWMODE_EN;
I915_WRITE(MEMMODECTL, rgvmodectl);
- while (I915_READ(MEMSWCTL) & MEMCTL_CMD_STS) {
- if (i++ > 100) {
- DRM_ERROR("stuck trying to change perf mode\n");
- break;
- }
- msleep(1);
- }
+ if (wait_for((I915_READ(MEMSWCTL) & MEMCTL_CMD_STS) == 0, 1, 0))
+ DRM_ERROR("stuck trying to change perf mode\n");
msleep(1);
ironlake_set_drps(dev, fstart);
I915_WRITE(DISP_ARB_CTL,
(I915_READ(DISP_ARB_CTL) |
DISP_FBC_WM_DIS));
+ I915_WRITE(WM3_LP_ILK, 0);
+ I915_WRITE(WM2_LP_ILK, 0);
+ I915_WRITE(WM1_LP_ILK, 0);
}
/*
* Based on the document from hardware guys the following bits
* GPU can automatically power down the render unit if given a page
* to save state.
*/
+ if (IS_IRONLAKE_M(dev)) {
+ if (dev_priv->renderctx == NULL)
+ dev_priv->renderctx = intel_alloc_context_page(dev);
+ if (dev_priv->renderctx) {
+ struct drm_i915_gem_object *obj_priv;
+ obj_priv = to_intel_bo(dev_priv->renderctx);
+ if (obj_priv) {
+ BEGIN_LP_RING(4);
+ OUT_RING(MI_SET_CONTEXT);
+ OUT_RING(obj_priv->gtt_offset |
+ MI_MM_SPACE_GTT |
+ MI_SAVE_EXT_STATE_EN |
+ MI_RESTORE_EXT_STATE_EN |
+ MI_RESTORE_INHIBIT);
+ OUT_RING(MI_NOOP);
+ OUT_RING(MI_FLUSH);
+ ADVANCE_LP_RING();
+ }
+ } else
+ DRM_DEBUG_KMS("Failed to allocate render context."
+ "Disable RC6\n");
+ }
+
if (I915_HAS_RC6(dev) && drm_core_check_feature(dev, DRIVER_MODESET)) {
struct drm_i915_gem_object *obj_priv = NULL;
} else {
struct drm_gem_object *pwrctx;
- pwrctx = intel_alloc_power_context(dev);
+ pwrctx = intel_alloc_context_page(dev);
if (pwrctx) {
dev_priv->pwrctx = pwrctx;
obj_priv = to_intel_bo(pwrctx);
}
}
+/* Disable the VGA plane that we never use */
+static void i915_disable_vga(struct drm_device *dev)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ u8 sr1;
+ u32 vga_reg;
+
+ if (HAS_PCH_SPLIT(dev))
+ vga_reg = CPU_VGACNTRL;
+ else
+ vga_reg = VGACNTRL;
+
+ vga_get_uninterruptible(dev->pdev, VGA_RSRC_LEGACY_IO);
+ outb(1, VGA_SR_INDEX);
+ sr1 = inb(VGA_SR_DATA);
+ outb(sr1 | 1<<5, VGA_SR_DATA);
+ vga_put(dev->pdev, VGA_RSRC_LEGACY_IO);
+ udelay(300);
+
+ I915_WRITE(vga_reg, VGA_DISP_DISABLE);
+ POSTING_READ(vga_reg);
+}
+
void intel_modeset_init(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
intel_init_clock_gating(dev);
+ /* Just disable it once at startup */
+ i915_disable_vga(dev);
+
if (IS_IRONLAKE_M(dev)) {
ironlake_enable_drps(dev);
intel_init_emon(dev);
if (dev_priv->display.disable_fbc)
dev_priv->display.disable_fbc(dev);
+ if (dev_priv->renderctx) {
+ struct drm_i915_gem_object *obj_priv;
+
+ obj_priv = to_intel_bo(dev_priv->renderctx);
+ I915_WRITE(CCID, obj_priv->gtt_offset &~ CCID_EN);
+ I915_READ(CCID);
+ i915_gem_object_unpin(dev_priv->renderctx);
+ drm_gem_object_unreference(dev_priv->renderctx);
+ }
+
if (dev_priv->pwrctx) {
struct drm_i915_gem_object *obj_priv;
git://bbs.cooldavid.org / net-next-2.6.git / blobdiff