[net-next-2.6.git] / net / dsa / mv88e6131.c

/*
 * net/dsa/mv88e6131.c - Marvell 88e6095/6095f/6131 switch chip support
 * Copyright (c) 2008-2009 Marvell Semiconductor
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 */

#include <linux/list.h>
#include <linux/netdevice.h>
#include <linux/phy.h>
#include "dsa_priv.h"
#include "mv88e6xxx.h"

static char *mv88e6131_probe(struct mii_bus *bus, int sw_addr)
{
	int ret;

	ret = __mv88e6xxx_reg_read(bus, sw_addr, REG_PORT(0), 0x03);
	if (ret >= 0) {
		ret &= 0xfff0;
		if (ret == 0x0950)
			return "Marvell 88E6095/88E6095F";
		if (ret == 0x1060)
			return "Marvell 88E6131";
	}

	return NULL;
}

static int mv88e6131_switch_reset(struct dsa_switch *ds)
{
	int i;
	int ret;

	/*
	 * Set all ports to the disabled state.
	 */
	for (i = 0; i < 11; i++) {
		ret = REG_READ(REG_PORT(i), 0x04);
		REG_WRITE(REG_PORT(i), 0x04, ret & 0xfffc);
	}

	/*
	 * Wait for transmit queues to drain.
	 */
	msleep(2);

	/*
	 * Reset the switch.
	 */
	REG_WRITE(REG_GLOBAL, 0x04, 0xc400);

	/*
	 * Wait up to one second for reset to complete.
	 */
	for (i = 0; i < 1000; i++) {
		ret = REG_READ(REG_GLOBAL, 0x00);
		if ((ret & 0xc800) == 0xc800)
			break;

		msleep(1);
	}
	if (i == 1000)
		return -ETIMEDOUT;

	return 0;
}

static int mv88e6131_setup_global(struct dsa_switch *ds)
{
	int ret;
	int i;

	/*
	 * Enable the PHY polling unit, don't discard packets with
	 * excessive collisions, use a weighted fair queueing scheme
	 * to arbitrate between packet queues, set the maximum frame
	 * size to 1632, and mask all interrupt sources.
	 */
	REG_WRITE(REG_GLOBAL, 0x04, 0x4400);

	/*
	 * Set the default address aging time to 5 minutes, and
	 * enable address learn messages to be sent to all message
	 * ports.
	 */
	REG_WRITE(REG_GLOBAL, 0x0a, 0x0148);

	/*
	 * Configure the priority mapping registers.
	 */
	ret = mv88e6xxx_config_prio(ds);
	if (ret < 0)
		return ret;

	/*
	 * Set the VLAN ethertype to 0x8100.
	 */
	REG_WRITE(REG_GLOBAL, 0x19, 0x8100);

	/*
	 * Disable ARP mirroring, and configure the upstream port as
	 * the port to which ingress and egress monitor frames are to
	 * be sent.
	 */
	REG_WRITE(REG_GLOBAL, 0x1a, (dsa_upstream_port(ds) * 0x1100) | 0x00f0);

	/*
	 * Disable cascade port functionality, and set the switch's
	 * DSA device number.
	 */
	REG_WRITE(REG_GLOBAL, 0x1c, 0xe000 | (ds->index & 0x1f));

	/*
	 * Send all frames with destination addresses matching
	 * 01:80:c2:00:00:0x to the CPU port.
	 */
	REG_WRITE(REG_GLOBAL2, 0x03, 0xffff);

	/*
	 * Ignore removed tag data on doubly tagged packets, disable
	 * flow control messages, force flow control priority to the
	 * highest, and send all special multicast frames to the CPU
	 * port at the higest priority.
	 */
	REG_WRITE(REG_GLOBAL2, 0x05, 0x00ff);

	/*
	 * Program the DSA routing table.
	 */
	for (i = 0; i < 32; i++) {
		int nexthop;

		nexthop = 0x1f;
		if (i != ds->index && i < ds->dst->pd->nr_chips)
			nexthop = ds->pd->rtable[i] & 0x1f;

		REG_WRITE(REG_GLOBAL2, 0x06, 0x8000 | (i << 8) | nexthop);
	}

	/*
	 * Clear all trunk masks.
	 */
	for (i = 0; i < 8; i++)
		REG_WRITE(REG_GLOBAL2, 0x07, 0x8000 | (i << 12) | 0x7ff);

	/*
	 * Clear all trunk mappings.
	 */
	for (i = 0; i < 16; i++)
		REG_WRITE(REG_GLOBAL2, 0x08, 0x8000 | (i << 11));

	/*
	 * Force the priority of IGMP/MLD snoop frames and ARP frames
	 * to the highest setting.
	 */
	REG_WRITE(REG_GLOBAL2, 0x0f, 0x00ff);

	return 0;
}

static int mv88e6131_setup_port(struct dsa_switch *ds, int p)
{
	int addr = REG_PORT(p);
	u16 val;

	/*
	 * MAC Forcing register: don't force link, speed, duplex
	 * or flow control state to any particular values on physical
	 * ports, but force the CPU port and all DSA ports to 1000 Mb/s
	 * full duplex.
	 */
	if (dsa_is_cpu_port(ds, p) || ds->dsa_port_mask & (1 << p))
		REG_WRITE(addr, 0x01, 0x003e);
	else
		REG_WRITE(addr, 0x01, 0x0003);

	/*
	 * Port Control: disable Core Tag, disable Drop-on-Lock,
	 * transmit frames unmodified, disable Header mode,
	 * enable IGMP/MLD snoop, disable DoubleTag, disable VLAN
	 * tunneling, determine priority by looking at 802.1p and
	 * IP priority fields (IP prio has precedence), and set STP
	 * state to Forwarding.
	 *
	 * If this is the upstream port for this switch, enable
	 * forwarding of unknown unicasts, and enable DSA tagging
	 * mode.
	 *
	 * If this is the link to another switch, use DSA tagging
	 * mode, but do not enable forwarding of unknown unicasts.
	 */
	val = 0x0433;
	if (p == dsa_upstream_port(ds))
		val |= 0x0104;
	if (ds->dsa_port_mask & (1 << p))
		val |= 0x0100;
	REG_WRITE(addr, 0x04, val);

	/*
	 * Port Control 1: disable trunking.  Also, if this is the
	 * CPU port, enable learn messages to be sent to this port.
	 */
	REG_WRITE(addr, 0x05, dsa_is_cpu_port(ds, p) ? 0x8000 : 0x0000);

	/*
	 * Port based VLAN map: give each port its own address
	 * database, allow the CPU port to talk to each of the 'real'
	 * ports, and allow each of the 'real' ports to only talk to
	 * the upstream port.
	 */
	val = (p & 0xf) << 12;
	if (dsa_is_cpu_port(ds, p))
		val |= ds->phys_port_mask;
	else
		val |= 1 << dsa_upstream_port(ds);
	REG_WRITE(addr, 0x06, val);

	/*
	 * Default VLAN ID and priority: don't set a default VLAN
	 * ID, and set the default packet priority to zero.
	 */
	REG_WRITE(addr, 0x07, 0x0000);

	/*
	 * Port Control 2: don't force a good FCS, don't use
	 * VLAN-based, source address-based or destination
	 * address-based priority overrides, don't let the switch
	 * add or strip 802.1q tags, don't discard tagged or
	 * untagged frames on this port, do a destination address
	 * lookup on received packets as usual, don't send a copy
	 * of all transmitted/received frames on this port to the
	 * CPU, and configure the upstream port number.
	 *
	 * If this is the upstream port for this switch, enable
	 * forwarding of unknown multicast addresses.
	 */
	val = 0x0080 | dsa_upstream_port(ds);
	if (p == dsa_upstream_port(ds))
		val |= 0x0040;
	REG_WRITE(addr, 0x08, val);

	/*
	 * Rate Control: disable ingress rate limiting.
	 */
	REG_WRITE(addr, 0x09, 0x0000);

	/*
	 * Rate Control 2: disable egress rate limiting.
	 */
	REG_WRITE(addr, 0x0a, 0x0000);

	/*
	 * Port Association Vector: when learning source addresses
	 * of packets, add the address to the address database using
	 * a port bitmap that has only the bit for this port set and
	 * the other bits clear.
	 */
	REG_WRITE(addr, 0x0b, 1 << p);

	/*
	 * Tag Remap: use an identity 802.1p prio -> switch prio
	 * mapping.
	 */
	REG_WRITE(addr, 0x18, 0x3210);

	/*
	 * Tag Remap 2: use an identity 802.1p prio -> switch prio
	 * mapping.
	 */
	REG_WRITE(addr, 0x19, 0x7654);

	return 0;
}

static int mv88e6131_setup(struct dsa_switch *ds)
{
	struct mv88e6xxx_priv_state *ps = (void *)(ds + 1);
	int i;
	int ret;

	mutex_init(&ps->smi_mutex);
	mv88e6xxx_ppu_state_init(ds);
	mutex_init(&ps->stats_mutex);

	ret = mv88e6131_switch_reset(ds);
	if (ret < 0)
		return ret;

	/* @@@ initialise vtu and atu */

	ret = mv88e6131_setup_global(ds);
	if (ret < 0)
		return ret;

	for (i = 0; i < 11; i++) {
		ret = mv88e6131_setup_port(ds, i);
		if (ret < 0)
			return ret;
	}

	return 0;
}

static int mv88e6131_port_to_phy_addr(int port)
{
	if (port >= 0 && port <= 11)
		return port;
	return -1;
}

static int
mv88e6131_phy_read(struct dsa_switch *ds, int port, int regnum)
{
	int addr = mv88e6131_port_to_phy_addr(port);
	return mv88e6xxx_phy_read_ppu(ds, addr, regnum);
}

static int
mv88e6131_phy_write(struct dsa_switch *ds,
			      int port, int regnum, u16 val)
{
	int addr = mv88e6131_port_to_phy_addr(port);
	return mv88e6xxx_phy_write_ppu(ds, addr, regnum, val);
}

static struct mv88e6xxx_hw_stat mv88e6131_hw_stats[] = {
	{ "in_good_octets", 8, 0x00, },
	{ "in_bad_octets", 4, 0x02, },
	{ "in_unicast", 4, 0x04, },
	{ "in_broadcasts", 4, 0x06, },
	{ "in_multicasts", 4, 0x07, },
	{ "in_pause", 4, 0x16, },
	{ "in_undersize", 4, 0x18, },
	{ "in_fragments", 4, 0x19, },
	{ "in_oversize", 4, 0x1a, },
	{ "in_jabber", 4, 0x1b, },
	{ "in_rx_error", 4, 0x1c, },
	{ "in_fcs_error", 4, 0x1d, },
	{ "out_octets", 8, 0x0e, },
	{ "out_unicast", 4, 0x10, },
	{ "out_broadcasts", 4, 0x13, },
	{ "out_multicasts", 4, 0x12, },
	{ "out_pause", 4, 0x15, },
	{ "excessive", 4, 0x11, },
	{ "collisions", 4, 0x1e, },
	{ "deferred", 4, 0x05, },
	{ "single", 4, 0x14, },
	{ "multiple", 4, 0x17, },
	{ "out_fcs_error", 4, 0x03, },
	{ "late", 4, 0x1f, },
	{ "hist_64bytes", 4, 0x08, },
	{ "hist_65_127bytes", 4, 0x09, },
	{ "hist_128_255bytes", 4, 0x0a, },
	{ "hist_256_511bytes", 4, 0x0b, },
	{ "hist_512_1023bytes", 4, 0x0c, },
	{ "hist_1024_max_bytes", 4, 0x0d, },
};

static void
mv88e6131_get_strings(struct dsa_switch *ds, int port, uint8_t *data)
{
	mv88e6xxx_get_strings(ds, ARRAY_SIZE(mv88e6131_hw_stats),
			      mv88e6131_hw_stats, port, data);
}

static void
mv88e6131_get_ethtool_stats(struct dsa_switch *ds,
				  int port, uint64_t *data)
{
	mv88e6xxx_get_ethtool_stats(ds, ARRAY_SIZE(mv88e6131_hw_stats),
				    mv88e6131_hw_stats, port, data);
}

static int mv88e6131_get_sset_count(struct dsa_switch *ds)
{
	return ARRAY_SIZE(mv88e6131_hw_stats);
}

static struct dsa_switch_driver mv88e6131_switch_driver = {
	.tag_protocol		= cpu_to_be16(ETH_P_DSA),
	.priv_size		= sizeof(struct mv88e6xxx_priv_state),
	.probe			= mv88e6131_probe,
	.setup			= mv88e6131_setup,
	.set_addr		= mv88e6xxx_set_addr_direct,
	.phy_read		= mv88e6131_phy_read,
	.phy_write		= mv88e6131_phy_write,
	.poll_link		= mv88e6xxx_poll_link,
	.get_strings		= mv88e6131_get_strings,
	.get_ethtool_stats	= mv88e6131_get_ethtool_stats,
	.get_sset_count		= mv88e6131_get_sset_count,
};

static int __init mv88e6131_init(void)
{
	register_switch_driver(&mv88e6131_switch_driver);
	return 0;
}
module_init(mv88e6131_init);

static void __exit mv88e6131_cleanup(void)
{
	unregister_switch_driver(&mv88e6131_switch_driver);
}
module_exit(mv88e6131_cleanup);
Commit	Line	Data
2e5f0320	1	/*
076d3e10 LB	2	* net/dsa/mv88e6131.c - Marvell 88e6095/6095f/6131 switch chip support
076d3e10 LB	3	* Copyright (c) 2008-2009 Marvell Semiconductor
2e5f0320 LB	4	*
	5	* This program is free software; you can redistribute it and/or modify
	6	* it under the terms of the GNU General Public License as published by
	7	* the Free Software Foundation; either version 2 of the License, or
	8	* (at your option) any later version.
	9	*/
	10
	11	#include <linux/list.h>
	12	#include <linux/netdevice.h>
	13	#include <linux/phy.h>
	14	#include "dsa_priv.h"
	15	#include "mv88e6xxx.h"
	16
	17	static char mv88e6131_probe(struct mii_bus bus, int sw_addr)
	18	{
	19	int ret;
	20
	21	ret = __mv88e6xxx_reg_read(bus, sw_addr, REG_PORT(0), 0x03);
	22	if (ret >= 0) {
	23	ret &= 0xfff0;
076d3e10 LB	24	if (ret == 0x0950)
076d3e10 LB	25	return "Marvell 88E6095/88E6095F";
2e5f0320 LB	26	if (ret == 0x1060)
	27	return "Marvell 88E6131";
	28	}
	29
	30	return NULL;
	31	}
	32
	33	static int mv88e6131_switch_reset(struct dsa_switch *ds)
	34	{
	35	int i;
	36	int ret;
	37
	38	/*
	39	* Set all ports to the disabled state.
	40	*/
076d3e10	41	for (i = 0; i < 11; i++) {
2e5f0320 LB	42	ret = REG_READ(REG_PORT(i), 0x04);
	43	REG_WRITE(REG_PORT(i), 0x04, ret & 0xfffc);
	44	}
	45
	46	/*
	47	* Wait for transmit queues to drain.
	48	*/
	49	msleep(2);
	50
	51	/*
	52	* Reset the switch.
	53	*/
	54	REG_WRITE(REG_GLOBAL, 0x04, 0xc400);
	55
	56	/*
	57	* Wait up to one second for reset to complete.
	58	*/
	59	for (i = 0; i < 1000; i++) {
	60	ret = REG_READ(REG_GLOBAL, 0x00);
	61	if ((ret & 0xc800) == 0xc800)
	62	break;
	63
	64	msleep(1);
	65	}
	66	if (i == 1000)
	67	return -ETIMEDOUT;
	68
	69	return 0;
	70	}
	71
	72	static int mv88e6131_setup_global(struct dsa_switch *ds)
	73	{
	74	int ret;
	75	int i;
	76
	77	/*
	78	* Enable the PHY polling unit, don't discard packets with
	79	* excessive collisions, use a weighted fair queueing scheme
	80	* to arbitrate between packet queues, set the maximum frame
	81	* size to 1632, and mask all interrupt sources.
	82	*/
	83	REG_WRITE(REG_GLOBAL, 0x04, 0x4400);
	84
	85	/*
	86	* Set the default address aging time to 5 minutes, and
	87	* enable address learn messages to be sent to all message
	88	* ports.
	89	*/
	90	REG_WRITE(REG_GLOBAL, 0x0a, 0x0148);
	91
	92	/*
	93	* Configure the priority mapping registers.
	94	*/
	95	ret = mv88e6xxx_config_prio(ds);
	96	if (ret < 0)
	97	return ret;
	98
	99	/*
	100	* Set the VLAN ethertype to 0x8100.
	101	*/
	102	REG_WRITE(REG_GLOBAL, 0x19, 0x8100);
	103
	104	/*
e84665c9 LB	105	* Disable ARP mirroring, and configure the upstream port as
	106	* the port to which ingress and egress monitor frames are to
	107	* be sent.
2e5f0320	108	*/
e84665c9	109	REG_WRITE(REG_GLOBAL, 0x1a, (dsa_upstream_port(ds) * 0x1100) \| 0x00f0);
2e5f0320 LB	110
	111	/*
	112	* Disable cascade port functionality, and set the switch's
e84665c9	113	* DSA device number.
2e5f0320	114	*/
e84665c9	115	REG_WRITE(REG_GLOBAL, 0x1c, 0xe000 \| (ds->index & 0x1f));
2e5f0320 LB	116
	117	/*
	118	* Send all frames with destination addresses matching
	119	* 01:80:c2:00:00:0x to the CPU port.
	120	*/
	121	REG_WRITE(REG_GLOBAL2, 0x03, 0xffff);
	122
	123	/*
	124	* Ignore removed tag data on doubly tagged packets, disable
	125	* flow control messages, force flow control priority to the
	126	* highest, and send all special multicast frames to the CPU
	127	* port at the higest priority.
	128	*/
	129	REG_WRITE(REG_GLOBAL2, 0x05, 0x00ff);
	130
	131	/*
e84665c9	132	* Program the DSA routing table.
2e5f0320	133	*/
e84665c9 LB	134	for (i = 0; i < 32; i++) {
	135	int nexthop;
	136
	137	nexthop = 0x1f;
	138	if (i != ds->index && i < ds->dst->pd->nr_chips)
	139	nexthop = ds->pd->rtable[i] & 0x1f;
	140
	141	REG_WRITE(REG_GLOBAL2, 0x06, 0x8000 \| (i << 8) \| nexthop);
	142	}
2e5f0320 LB	143
	144	/*
	145	* Clear all trunk masks.
	146	*/
	147	for (i = 0; i < 8; i++)
076d3e10	148	REG_WRITE(REG_GLOBAL2, 0x07, 0x8000 \| (i << 12) \| 0x7ff);
2e5f0320 LB	149
	150	/*
	151	* Clear all trunk mappings.
	152	*/
	153	for (i = 0; i < 16; i++)
	154	REG_WRITE(REG_GLOBAL2, 0x08, 0x8000 \| (i << 11));
	155
	156	/*
	157	* Force the priority of IGMP/MLD snoop frames and ARP frames
	158	* to the highest setting.
	159	*/
	160	REG_WRITE(REG_GLOBAL2, 0x0f, 0x00ff);
	161
	162	return 0;
	163	}
	164
	165	static int mv88e6131_setup_port(struct dsa_switch *ds, int p)
	166	{
	167	int addr = REG_PORT(p);
e84665c9	168	u16 val;
2e5f0320 LB	169
	170	/*
	171	* MAC Forcing register: don't force link, speed, duplex
076d3e10	172	* or flow control state to any particular values on physical
e84665c9 LB	173	* ports, but force the CPU port and all DSA ports to 1000 Mb/s
e84665c9 LB	174	* full duplex.
2e5f0320	175	*/
e84665c9	176	if (dsa_is_cpu_port(ds, p) \|\| ds->dsa_port_mask & (1 << p))
076d3e10 LB	177	REG_WRITE(addr, 0x01, 0x003e);
	178	else
	179	REG_WRITE(addr, 0x01, 0x0003);
2e5f0320 LB	180
	181	/*
	182	* Port Control: disable Core Tag, disable Drop-on-Lock,
	183	* transmit frames unmodified, disable Header mode,
	184	* enable IGMP/MLD snoop, disable DoubleTag, disable VLAN
	185	* tunneling, determine priority by looking at 802.1p and
	186	* IP priority fields (IP prio has precedence), and set STP
e84665c9 LB	187	* state to Forwarding.
	188	*
	189	* If this is the upstream port for this switch, enable
	190	* forwarding of unknown unicasts, and enable DSA tagging
	191	* mode.
	192	*
	193	* If this is the link to another switch, use DSA tagging
	194	* mode, but do not enable forwarding of unknown unicasts.
2e5f0320	195	*/
e84665c9 LB	196	val = 0x0433;
	197	if (p == dsa_upstream_port(ds))
	198	val \|= 0x0104;
	199	if (ds->dsa_port_mask & (1 << p))
	200	val \|= 0x0100;
	201	REG_WRITE(addr, 0x04, val);
2e5f0320 LB	202
	203	/*
	204	* Port Control 1: disable trunking. Also, if this is the
	205	* CPU port, enable learn messages to be sent to this port.
	206	*/
e84665c9	207	REG_WRITE(addr, 0x05, dsa_is_cpu_port(ds, p) ? 0x8000 : 0x0000);
2e5f0320 LB	208
	209	/*
	210	* Port based VLAN map: give each port its own address
	211	* database, allow the CPU port to talk to each of the 'real'
	212	* ports, and allow each of the 'real' ports to only talk to
e84665c9	213	* the upstream port.
2e5f0320	214	*/
e84665c9 LB	215	val = (p & 0xf) << 12;
	216	if (dsa_is_cpu_port(ds, p))
	217	val \|= ds->phys_port_mask;
	218	else
	219	val \|= 1 << dsa_upstream_port(ds);
	220	REG_WRITE(addr, 0x06, val);
2e5f0320 LB	221
	222	/*
	223	* Default VLAN ID and priority: don't set a default VLAN
	224	* ID, and set the default packet priority to zero.
	225	*/
	226	REG_WRITE(addr, 0x07, 0x0000);
	227
	228	/*
	229	* Port Control 2: don't force a good FCS, don't use
	230	* VLAN-based, source address-based or destination
	231	* address-based priority overrides, don't let the switch
	232	* add or strip 802.1q tags, don't discard tagged or
	233	* untagged frames on this port, do a destination address
	234	* lookup on received packets as usual, don't send a copy
	235	* of all transmitted/received frames on this port to the
e84665c9 LB	236	* CPU, and configure the upstream port number.
	237	*
	238	* If this is the upstream port for this switch, enable
	239	* forwarding of unknown multicast addresses.
2e5f0320	240	*/
e84665c9 LB	241	val = 0x0080 \| dsa_upstream_port(ds);
	242	if (p == dsa_upstream_port(ds))
	243	val \|= 0x0040;
	244	REG_WRITE(addr, 0x08, val);
2e5f0320 LB	245
	246	/*
	247	* Rate Control: disable ingress rate limiting.
	248	*/
	249	REG_WRITE(addr, 0x09, 0x0000);
	250
	251	/*
	252	* Rate Control 2: disable egress rate limiting.
	253	*/
	254	REG_WRITE(addr, 0x0a, 0x0000);
	255
	256	/*
	257	* Port Association Vector: when learning source addresses
	258	* of packets, add the address to the address database using
	259	* a port bitmap that has only the bit for this port set and
	260	* the other bits clear.
	261	*/
	262	REG_WRITE(addr, 0x0b, 1 << p);
	263
	264	/*
	265	* Tag Remap: use an identity 802.1p prio -> switch prio
	266	* mapping.
	267	*/
	268	REG_WRITE(addr, 0x18, 0x3210);
	269
	270	/*
	271	* Tag Remap 2: use an identity 802.1p prio -> switch prio
	272	* mapping.
	273	*/
	274	REG_WRITE(addr, 0x19, 0x7654);
	275
	276	return 0;
	277	}
	278
	279	static int mv88e6131_setup(struct dsa_switch *ds)
	280	{
	281	struct mv88e6xxx_priv_state ps = (void )(ds + 1);
	282	int i;
	283	int ret;
	284
	285	mutex_init(&ps->smi_mutex);
	286	mv88e6xxx_ppu_state_init(ds);
	287	mutex_init(&ps->stats_mutex);
	288
	289	ret = mv88e6131_switch_reset(ds);
	290	if (ret < 0)
	291	return ret;
	292
	293	/* @@@ initialise vtu and atu */
	294
	295	ret = mv88e6131_setup_global(ds);
	296	if (ret < 0)
	297	return ret;
	298
076d3e10	299	for (i = 0; i < 11; i++) {
2e5f0320 LB	300	ret = mv88e6131_setup_port(ds, i);
	301	if (ret < 0)
	302	return ret;
	303	}
	304
	305	return 0;
	306	}
	307
	308	static int mv88e6131_port_to_phy_addr(int port)
	309	{
076d3e10	310	if (port >= 0 && port <= 11)
2e5f0320 LB	311	return port;
	312	return -1;
	313	}
	314
	315	static int
	316	mv88e6131_phy_read(struct dsa_switch *ds, int port, int regnum)
	317	{
	318	int addr = mv88e6131_port_to_phy_addr(port);
	319	return mv88e6xxx_phy_read_ppu(ds, addr, regnum);
	320	}
	321
	322	static int
	323	mv88e6131_phy_write(struct dsa_switch *ds,
	324	int port, int regnum, u16 val)
	325	{
	326	int addr = mv88e6131_port_to_phy_addr(port);
	327	return mv88e6xxx_phy_write_ppu(ds, addr, regnum, val);
	328	}
	329
	330	static struct mv88e6xxx_hw_stat mv88e6131_hw_stats[] = {
	331	{ "in_good_octets", 8, 0x00, },
	332	{ "in_bad_octets", 4, 0x02, },
	333	{ "in_unicast", 4, 0x04, },
	334	{ "in_broadcasts", 4, 0x06, },
	335	{ "in_multicasts", 4, 0x07, },
	336	{ "in_pause", 4, 0x16, },
	337	{ "in_undersize", 4, 0x18, },
	338	{ "in_fragments", 4, 0x19, },
	339	{ "in_oversize", 4, 0x1a, },
	340	{ "in_jabber", 4, 0x1b, },
	341	{ "in_rx_error", 4, 0x1c, },
	342	{ "in_fcs_error", 4, 0x1d, },
	343	{ "out_octets", 8, 0x0e, },
	344	{ "out_unicast", 4, 0x10, },
	345	{ "out_broadcasts", 4, 0x13, },
	346	{ "out_multicasts", 4, 0x12, },
	347	{ "out_pause", 4, 0x15, },
	348	{ "excessive", 4, 0x11, },
	349	{ "collisions", 4, 0x1e, },
	350	{ "deferred", 4, 0x05, },
	351	{ "single", 4, 0x14, },
	352	{ "multiple", 4, 0x17, },
	353	{ "out_fcs_error", 4, 0x03, },
	354	{ "late", 4, 0x1f, },
	355	{ "hist_64bytes", 4, 0x08, },
	356	{ "hist_65_127bytes", 4, 0x09, },
	357	{ "hist_128_255bytes", 4, 0x0a, },
	358	{ "hist_256_511bytes", 4, 0x0b, },
	359	{ "hist_512_1023bytes", 4, 0x0c, },
	360	{ "hist_1024_max_bytes", 4, 0x0d, },
	361	};
	362
	363	static void
	364	mv88e6131_get_strings(struct dsa_switch ds, int port, uint8_t data)
	365	{
	366	mv88e6xxx_get_strings(ds, ARRAY_SIZE(mv88e6131_hw_stats),
	367	mv88e6131_hw_stats, port, data);
	368	}
	369
	370	static void
	371	mv88e6131_get_ethtool_stats(struct dsa_switch *ds,
	372	int port, uint64_t *data)
	373	{
	374	mv88e6xxx_get_ethtool_stats(ds, ARRAY_SIZE(mv88e6131_hw_stats),
375	mv88e6131_hw_stats, port, data);
376	}
377
378	static int mv88e6131_get_sset_count(struct dsa_switch *ds)
379	{
380	return ARRAY_SIZE(mv88e6131_hw_stats);
381	}
382
383	static struct dsa_switch_driver mv88e6131_switch_driver = {
09640e63	384	.tag_protocol = cpu_to_be16(ETH_P_DSA),
2e5f0320 LB	385	.priv_size = sizeof(struct mv88e6xxx_priv_state),
	386	.probe = mv88e6131_probe,
	387	.setup = mv88e6131_setup,
	388	.set_addr = mv88e6xxx_set_addr_direct,
	389	.phy_read = mv88e6131_phy_read,
	390	.phy_write = mv88e6131_phy_write,
	391	.poll_link = mv88e6xxx_poll_link,
	392	.get_strings = mv88e6131_get_strings,
	393	.get_ethtool_stats = mv88e6131_get_ethtool_stats,
	394	.get_sset_count = mv88e6131_get_sset_count,
	395	};
	396
5eaa65b2	397	static int __init mv88e6131_init(void)
2e5f0320 LB	398	{
	399	register_switch_driver(&mv88e6131_switch_driver);
	400	return 0;
	401	}
	402	module_init(mv88e6131_init);
	403
5eaa65b2	404	static void __exit mv88e6131_cleanup(void)
2e5f0320 LB	405	{
	406	unregister_switch_driver(&mv88e6131_switch_driver);
	407	}
	408	module_exit(mv88e6131_cleanup);