[net-next-2.6.git] / include / linux / lp.h

#ifndef _LINUX_LP_H
#define _LINUX_LP_H

/*
 * usr/include/linux/lp.h c.1991-1992 James Wiegand
 * many modifications copyright (C) 1992 Michael K. Johnson
 * Interrupt support added 1993 Nigel Gamble
 * Removed 8255 status defines from inside __KERNEL__ Marcelo Tosatti 
 */

/*
 * Per POSIX guidelines, this module reserves the LP and lp prefixes
 * These are the lp_table[minor].flags flags...
 */
#define LP_EXIST 0x0001
#define LP_SELEC 0x0002
#define LP_BUSY	 0x0004
#define LP_BUSY_BIT_POS 2
#define LP_OFFL	 0x0008
#define LP_NOPA  0x0010
#define LP_ERR   0x0020
#define LP_ABORT 0x0040
#define LP_CAREFUL 0x0080 /* obsoleted -arca */
#define LP_ABORTOPEN 0x0100

#define LP_TRUST_IRQ_  0x0200 /* obsolete */
#define LP_NO_REVERSE  0x0400 /* No reverse mode available. */
#define LP_DATA_AVAIL  0x0800 /* Data is available. */

/* 
 * bit defines for 8255 status port
 * base + 1
 * accessed with LP_S(minor), which gets the byte...
 */
#define LP_PBUSY	0x80  /* inverted input, active high */
#define LP_PACK		0x40  /* unchanged input, active low */
#define LP_POUTPA	0x20  /* unchanged input, active high */
#define LP_PSELECD	0x10  /* unchanged input, active high */
#define LP_PERRORP	0x08  /* unchanged input, active low */

/* timeout for each character.  This is relative to bus cycles -- it
 * is the count in a busy loop.  THIS IS THE VALUE TO CHANGE if you
 * have extremely slow printing, or if the machine seems to slow down
 * a lot when you print.  If you have slow printing, increase this
 * number and recompile, and if your system gets bogged down, decrease
 * this number.  This can be changed with the tunelp(8) command as well.
 */

#define LP_INIT_CHAR 1000

/* The parallel port specs apparently say that there needs to be
 * a .5usec wait before and after the strobe.
 */

#define LP_INIT_WAIT 1

/* This is the amount of time that the driver waits for the printer to
 * catch up when the printer's buffer appears to be filled.  If you
 * want to tune this and have a fast printer (i.e. HPIIIP), decrease
 * this number, and if you have a slow printer, increase this number.
 * This is in hundredths of a second, the default 2 being .05 second.
 * Or use the tunelp(8) command, which is especially nice if you want
 * change back and forth between character and graphics printing, which
 * are wildly different...
 */

#define LP_INIT_TIME 2

/* IOCTL numbers */
#define LPCHAR   0x0601  /* corresponds to LP_INIT_CHAR */
#define LPTIME   0x0602  /* corresponds to LP_INIT_TIME */
#define LPABORT  0x0604  /* call with TRUE arg to abort on error,
			    FALSE to retry.  Default is retry.  */
#define LPSETIRQ 0x0605  /* call with new IRQ number,
			    or 0 for polling (no IRQ) */
#define LPGETIRQ 0x0606  /* get the current IRQ number */
#define LPWAIT   0x0608  /* corresponds to LP_INIT_WAIT */
/* NOTE: LPCAREFUL is obsoleted and it' s always the default right now -arca */
#define LPCAREFUL   0x0609  /* call with TRUE arg to require out-of-paper, off-
			    line, and error indicators good on all writes,
			    FALSE to ignore them.  Default is ignore. */
#define LPABORTOPEN 0x060a  /* call with TRUE arg to abort open() on error,
			    FALSE to ignore error.  Default is ignore.  */
#define LPGETSTATUS 0x060b  /* return LP_S(minor) */
#define LPRESET     0x060c  /* reset printer */
#ifdef LP_STATS
#define LPGETSTATS  0x060d  /* get statistics (struct lp_stats) */
#endif
#define LPGETFLAGS  0x060e  /* get status flags */
#define LPSETTIMEOUT 0x060f /* set parport timeout */

/* timeout for printk'ing a timeout, in jiffies (100ths of a second).
   This is also used for re-checking error conditions if LP_ABORT is
   not set.  This is the default behavior. */

#define LP_TIMEOUT_INTERRUPT	(60 * HZ)
#define LP_TIMEOUT_POLLED	(10 * HZ)

#ifdef __KERNEL__

#include <linux/wait.h>
#include <linux/mutex.h>

/* Magic numbers for defining port-device mappings */
#define LP_PARPORT_UNSPEC -4
#define LP_PARPORT_AUTO -3
#define LP_PARPORT_OFF -2
#define LP_PARPORT_NONE -1

#define LP_F(minor)	lp_table[(minor)].flags		/* flags for busy, etc. */
#define LP_CHAR(minor)	lp_table[(minor)].chars		/* busy timeout */
#define LP_TIME(minor)	lp_table[(minor)].time		/* wait time */
#define LP_WAIT(minor)	lp_table[(minor)].wait		/* strobe wait */
#define LP_IRQ(minor)	lp_table[(minor)].dev->port->irq /* interrupt # */
					/* PARPORT_IRQ_NONE means polled */
#ifdef LP_STATS
#define LP_STAT(minor)	lp_table[(minor)].stats		/* statistics area */
#endif
#define LP_BUFFER_SIZE PAGE_SIZE

#define LP_BASE(x)	lp_table[(x)].dev->port->base

#ifdef LP_STATS
struct lp_stats {
	unsigned long chars;
	unsigned long sleeps;
	unsigned int maxrun;
	unsigned int maxwait;
	unsigned int meanwait;
	unsigned int mdev;
};
#endif

struct lp_struct {
	struct pardevice *dev;
	unsigned long flags;
	unsigned int chars;
	unsigned int time;
	unsigned int wait;
	char *lp_buffer;
#ifdef LP_STATS
	unsigned int lastcall;
	unsigned int runchars;
	struct lp_stats stats;
#endif
	wait_queue_head_t waitq;
	unsigned int last_error;
	struct mutex port_mutex;
	wait_queue_head_t dataq;
	long timeout;
	unsigned int best_mode;
	unsigned int current_mode;
	unsigned long bits;
};

/*
 * The following constants describe the various signals of the printer port
 * hardware.  Note that the hardware inverts some signals and that some
 * signals are active low.  An example is LP_STROBE, which must be programmed
 * with 1 for being active and 0 for being inactive, because the strobe signal
 * gets inverted, but it is also active low.
 */


/* 
 * defines for 8255 control port
 * base + 2 
 * accessed with LP_C(minor)
 */
#define LP_PINTEN	0x10  /* high to read data in or-ed with data out */
#define LP_PSELECP	0x08  /* inverted output, active low */
#define LP_PINITP	0x04  /* unchanged output, active low */
#define LP_PAUTOLF	0x02  /* inverted output, active low */
#define LP_PSTROBE	0x01  /* short high output on raising edge */

/* 
 * the value written to ports to test existence. PC-style ports will 
 * return the value written. AT-style ports will return 0. so why not
 * make them the same ? 
 */
#define LP_DUMMY	0x00

/*
 * This is the port delay time, in microseconds.
 * It is used only in the lp_init() and lp_reset() routine.
 */
#define LP_DELAY 	50

#endif

#endif
Commit	Line	Data
1da177e4 LT	1	#ifndef _LINUX_LP_H
	2	#define _LINUX_LP_H
	3
	4	/*
	5	* usr/include/linux/lp.h c.1991-1992 James Wiegand
	6	* many modifications copyright (C) 1992 Michael K. Johnson
	7	* Interrupt support added 1993 Nigel Gamble
	8	* Removed 8255 status defines from inside __KERNEL__ Marcelo Tosatti
	9	*/
	10
	11	/*
	12	* Per POSIX guidelines, this module reserves the LP and lp prefixes
	13	* These are the lp_table[minor].flags flags...
	14	*/
	15	#define LP_EXIST 0x0001
	16	#define LP_SELEC 0x0002
	17	#define LP_BUSY 0x0004
	18	#define LP_BUSY_BIT_POS 2
	19	#define LP_OFFL 0x0008
	20	#define LP_NOPA 0x0010
	21	#define LP_ERR 0x0020
	22	#define LP_ABORT 0x0040
	23	#define LP_CAREFUL 0x0080 /* obsoleted -arca */
	24	#define LP_ABORTOPEN 0x0100
	25
	26	#define LP_TRUST_IRQ_ 0x0200 /* obsolete */
	27	#define LP_NO_REVERSE 0x0400 /* No reverse mode available. */
	28	#define LP_DATA_AVAIL 0x0800 /* Data is available. */
	29
	30	/*
	31	* bit defines for 8255 status port
	32	* base + 1
	33	* accessed with LP_S(minor), which gets the byte...
	34	*/
	35	#define LP_PBUSY 0x80 /* inverted input, active high */
	36	#define LP_PACK 0x40 /* unchanged input, active low */
	37	#define LP_POUTPA 0x20 /* unchanged input, active high */
	38	#define LP_PSELECD 0x10 /* unchanged input, active high */
	39	#define LP_PERRORP 0x08 /* unchanged input, active low */
	40
	41	/* timeout for each character. This is relative to bus cycles -- it
	42	* is the count in a busy loop. THIS IS THE VALUE TO CHANGE if you
	43	* have extremely slow printing, or if the machine seems to slow down
	44	* a lot when you print. If you have slow printing, increase this
	45	* number and recompile, and if your system gets bogged down, decrease
	46	* this number. This can be changed with the tunelp(8) command as well.
	47	*/
	48
	49	#define LP_INIT_CHAR 1000
	50
	51	/* The parallel port specs apparently say that there needs to be
	52	* a .5usec wait before and after the strobe.
	53	*/
	54
	55	#define LP_INIT_WAIT 1
	56
	57	/* This is the amount of time that the driver waits for the printer to
	58	* catch up when the printer's buffer appears to be filled. If you
	59	* want to tune this and have a fast printer (i.e. HPIIIP), decrease
	60	* this number, and if you have a slow printer, increase this number.
	61	* This is in hundredths of a second, the default 2 being .05 second.
	62	* Or use the tunelp(8) command, which is especially nice if you want
	63	* change back and forth between character and graphics printing, which
	64	* are wildly different...
65	*/
66
67	#define LP_INIT_TIME 2
68
69	/* IOCTL numbers */
70	#define LPCHAR 0x0601 /* corresponds to LP_INIT_CHAR */
71	#define LPTIME 0x0602 /* corresponds to LP_INIT_TIME */
72	#define LPABORT 0x0604 /* call with TRUE arg to abort on error,
73	FALSE to retry. Default is retry. */
74	#define LPSETIRQ 0x0605 /* call with new IRQ number,
75	or 0 for polling (no IRQ) */
76	#define LPGETIRQ 0x0606 /* get the current IRQ number */
77	#define LPWAIT 0x0608 /* corresponds to LP_INIT_WAIT */
78	/* NOTE: LPCAREFUL is obsoleted and it' s always the default right now -arca */
79	#define LPCAREFUL 0x0609 /* call with TRUE arg to require out-of-paper, off-
80	line, and error indicators good on all writes,
81	FALSE to ignore them. Default is ignore. */
82	#define LPABORTOPEN 0x060a /* call with TRUE arg to abort open() on error,
83	FALSE to ignore error. Default is ignore. */
84	#define LPGETSTATUS 0x060b /* return LP_S(minor) */
85	#define LPRESET 0x060c /* reset printer */
86	#ifdef LP_STATS
87	#define LPGETSTATS 0x060d /* get statistics (struct lp_stats) */
88	#endif
89	#define LPGETFLAGS 0x060e /* get status flags */
90	#define LPSETTIMEOUT 0x060f /* set parport timeout */
91
92	/* timeout for printk'ing a timeout, in jiffies (100ths of a second).
93	This is also used for re-checking error conditions if LP_ABORT is
94	not set. This is the default behavior. */
95
96	#define LP_TIMEOUT_INTERRUPT (60 * HZ)
97	#define LP_TIMEOUT_POLLED (10 * HZ)
98
99	#ifdef __KERNEL__
100
101	#include <linux/wait.h>
0a5dcb51	102	#include <linux/mutex.h>
1da177e4 LT	103
	104	/* Magic numbers for defining port-device mappings */
	105	#define LP_PARPORT_UNSPEC -4
	106	#define LP_PARPORT_AUTO -3
	107	#define LP_PARPORT_OFF -2
	108	#define LP_PARPORT_NONE -1
	109
	110	#define LP_F(minor) lp_table[(minor)].flags /* flags for busy, etc. */
	111	#define LP_CHAR(minor) lp_table[(minor)].chars /* busy timeout */
	112	#define LP_TIME(minor) lp_table[(minor)].time /* wait time */
	113	#define LP_WAIT(minor) lp_table[(minor)].wait /* strobe wait */
	114	#define LP_IRQ(minor) lp_table[(minor)].dev->port->irq /* interrupt # */
	115	/* PARPORT_IRQ_NONE means polled */
	116	#ifdef LP_STATS
	117	#define LP_STAT(minor) lp_table[(minor)].stats /* statistics area */
	118	#endif
	119	#define LP_BUFFER_SIZE PAGE_SIZE
	120
	121	#define LP_BASE(x) lp_table[(x)].dev->port->base
	122
	123	#ifdef LP_STATS
	124	struct lp_stats {
	125	unsigned long chars;
	126	unsigned long sleeps;
	127	unsigned int maxrun;
	128	unsigned int maxwait;
	129	unsigned int meanwait;
	130	unsigned int mdev;
	131	};
	132	#endif
	133
	134	struct lp_struct {
	135	struct pardevice *dev;
	136	unsigned long flags;
	137	unsigned int chars;
	138	unsigned int time;
	139	unsigned int wait;
	140	char *lp_buffer;
	141	#ifdef LP_STATS
	142	unsigned int lastcall;
	143	unsigned int runchars;
	144	struct lp_stats stats;
	145	#endif
	146	wait_queue_head_t waitq;
	147	unsigned int last_error;
0a5dcb51	148	struct mutex port_mutex;
1da177e4 LT	149	wait_queue_head_t dataq;
	150	long timeout;
	151	unsigned int best_mode;
	152	unsigned int current_mode;
	153	unsigned long bits;
	154	};
	155
	156	/*
	157	* The following constants describe the various signals of the printer port
	158	* hardware. Note that the hardware inverts some signals and that some
	159	* signals are active low. An example is LP_STROBE, which must be programmed
	160	* with 1 for being active and 0 for being inactive, because the strobe signal
	161	* gets inverted, but it is also active low.
	162	*/
	163
	164
	165	/*
	166	* defines for 8255 control port
	167	* base + 2
	168	* accessed with LP_C(minor)
	169	*/
	170	#define LP_PINTEN 0x10 /* high to read data in or-ed with data out */
	171	#define LP_PSELECP 0x08 /* inverted output, active low */
	172	#define LP_PINITP 0x04 /* unchanged output, active low */
	173	#define LP_PAUTOLF 0x02 /* inverted output, active low */
	174	#define LP_PSTROBE 0x01 /* short high output on raising edge */
	175
	176	/*
	177	* the value written to ports to test existence. PC-style ports will
	178	* return the value written. AT-style ports will return 0. so why not
	179	* make them the same ?
	180	*/
	181	#define LP_DUMMY 0x00
	182
	183	/*
	184	* This is the port delay time, in microseconds.
	185	* It is used only in the lp_init() and lp_reset() routine.
	186	*/
	187	#define LP_DELAY 50
	188
	189	#endif
	190
	191	#endif