[net-next-2.6.git] / drivers / usb / host / Kconfig

#
# USB Host Controller Drivers
#
comment "USB Host Controller Drivers"
	depends on USB

config USB_EHCI_HCD
	tristate "EHCI HCD (USB 2.0) support"
	depends on USB && USB_ARCH_HAS_EHCI
	---help---
	  The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
	  "high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware.
	  If your USB host controller supports USB 2.0, you will likely want to
	  configure this Host Controller Driver.  At the time of this writing, 
	  the primary implementation of EHCI is a chip from NEC, widely available
	  in add-on PCI cards, but implementations are in the works from other 
	  vendors including Intel and Philips.  Motherboard support is appearing.

	  EHCI controllers are packaged with "companion" host controllers (OHCI
	  or UHCI) to handle USB 1.1 devices connected to root hub ports.  Ports
	  will connect to EHCI if the device is high speed, otherwise they
	  connect to a companion controller.  If you configure EHCI, you should
	  probably configure the OHCI (for NEC and some other vendors) USB Host
	  Controller Driver or UHCI (for Via motherboards) Host Controller
	  Driver too.

	  You may want to read <file:Documentation/usb/ehci.txt>.

	  To compile this driver as a module, choose M here: the
	  module will be called ehci-hcd.

config USB_EHCI_SPLIT_ISO
	bool "Full speed ISO transactions (EXPERIMENTAL)"
	depends on USB_EHCI_HCD && EXPERIMENTAL
	default n
	---help---
	  This code is new and hasn't been used with many different
	  EHCI or USB 2.0 transaction translator implementations.
	  It should work for ISO-OUT transfers, like audio.

config USB_EHCI_ROOT_HUB_TT
	bool "Root Hub Transaction Translators (EXPERIMENTAL)"
	depends on USB_EHCI_HCD && EXPERIMENTAL
	---help---
	  Some EHCI chips have vendor-specific extensions to integrate
	  transaction translators, so that no OHCI or UHCI companion
	  controller is needed.  It's safe to say "y" even if your
	  controller doesn't support this feature.

	  This supports the EHCI implementation that's originally
	  from ARC, and has since changed hands a few times.

config USB_EHCI_TT_NEWSCHED
	bool "Improved Transaction Translator scheduling (EXPERIMENTAL)"
	depends on USB_EHCI_HCD && EXPERIMENTAL
	---help---
	  This changes the periodic scheduling code to fill more of the low
	  and full speed bandwidth available from the Transaction Translator
	  (TT) in USB 2.0 hubs.  Without this, only one transfer will be
	  issued in each microframe, significantly reducing the number of
	  periodic low/fullspeed transfers possible.

	  If you have multiple periodic low/fullspeed devices connected to a
	  highspeed USB hub which is connected to a highspeed USB Host
	  Controller, and some of those devices will not work correctly
	  (possibly due to "ENOSPC" or "-28" errors), say Y.

	  If unsure, say N.

config USB_EHCI_BIG_ENDIAN_MMIO
	bool
	depends on USB_EHCI_HCD
	default n

config USB_EHCI_BIG_ENDIAN_DESC
	bool
	depends on USB_EHCI_HCD
	default n

config USB_ISP116X_HCD
	tristate "ISP116X HCD support"
	depends on USB
	---help---
	  The ISP1160 and ISP1161 chips are USB host controllers. Enable this
	  option if your board has this chip. If unsure, say N.

	  This driver does not support isochronous transfers.

	  To compile this driver as a module, choose M here: the
	  module will be called isp116x-hcd.

config USB_OHCI_HCD
	tristate "OHCI HCD support"
	depends on USB && USB_ARCH_HAS_OHCI
	select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3
	select I2C if ARCH_PNX4008
	---help---
	  The Open Host Controller Interface (OHCI) is a standard for accessing
	  USB 1.1 host controller hardware.  It does more in hardware than Intel's
	  UHCI specification.  If your USB host controller follows the OHCI spec,
	  say Y.  On most non-x86 systems, and on x86 hardware that's not using a
	  USB controller from Intel or VIA, this is appropriate.  If your host
	  controller doesn't use PCI, this is probably appropriate.  For a PCI
	  based system where you're not sure, the "lspci -v" entry will list the
	  right "prog-if" for your USB controller(s):  EHCI, OHCI, or UHCI.

	  To compile this driver as a module, choose M here: the
	  module will be called ohci-hcd.

config USB_OHCI_HCD_PPC_SOC
	bool "OHCI support for on-chip PPC USB controller"
	depends on USB_OHCI_HCD && (STB03xxx || PPC_MPC52xx)
	default y
	select USB_OHCI_BIG_ENDIAN_DESC
	select USB_OHCI_BIG_ENDIAN_MMIO
	---help---
	  Enables support for the USB controller on the MPC52xx or
	  STB03xxx processor chip.  If unsure, say Y.

config USB_OHCI_HCD_PPC_OF
	bool "OHCI support for PPC USB controller on OF platform bus"
	depends on USB_OHCI_HCD && PPC_OF
	default y
	---help---
	  Enables support for the USB controller PowerPC present on the
	  OpenFirmware platform bus.

config USB_OHCI_HCD_PPC_OF_BE
	bool "Support big endian HC"
	depends on USB_OHCI_HCD_PPC_OF
	default y
	select USB_OHCI_BIG_ENDIAN_DESC
	select USB_OHCI_BIG_ENDIAN_MMIO

config USB_OHCI_HCD_PPC_OF_LE
	bool "Support little endian HC"
	depends on USB_OHCI_HCD_PPC_OF
	default n
	select USB_OHCI_LITTLE_ENDIAN

config USB_OHCI_HCD_PCI
	bool "OHCI support for PCI-bus USB controllers"
	depends on USB_OHCI_HCD && PCI && (STB03xxx || PPC_MPC52xx || USB_OHCI_HCD_PPC_OF)
	default y
	select USB_OHCI_LITTLE_ENDIAN
	---help---
	  Enables support for PCI-bus plug-in USB controller cards.
	  If unsure, say Y.

config USB_OHCI_BIG_ENDIAN_DESC
	bool
	depends on USB_OHCI_HCD
	default n

config USB_OHCI_BIG_ENDIAN_MMIO
	bool
	depends on USB_OHCI_HCD
	default n

config USB_OHCI_LITTLE_ENDIAN
	bool
	depends on USB_OHCI_HCD
	default n if STB03xxx || PPC_MPC52xx
	default y

config USB_UHCI_HCD
	tristate "UHCI HCD (most Intel and VIA) support"
	depends on USB && PCI
	---help---
	  The Universal Host Controller Interface is a standard by Intel for
	  accessing the USB hardware in the PC (which is also called the USB
	  host controller). If your USB host controller conforms to this
	  standard, you may want to say Y, but see below. All recent boards
	  with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX,
	  i810, i820) conform to this standard. Also all VIA PCI chipsets
	  (like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro
	  133). If unsure, say Y.

	  To compile this driver as a module, choose M here: the
	  module will be called uhci-hcd.

config USB_U132_HCD
	tristate "Elan U132 Adapter Host Controller"
	depends on USB && USB_FTDI_ELAN
	default M
	help
	  The U132 adapter is a USB to CardBus adapter specifically designed
	  for PC cards that contain an OHCI host controller. Typical PC cards
	  are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132
	  adapter will *NOT* work with PC cards that do not contain an OHCI
	  controller.

	  For those PC cards that contain multiple OHCI controllers only the
	  first one is used.

	  The driver consists of two modules, the "ftdi-elan" module is a
	  USB client driver that interfaces to the FTDI chip within ELAN's
	  USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host
	  controller driver that talks to the OHCI controller within the
	  CardBus cards that are inserted in the U132 adapter.

	  This driver has been tested with a CardBus OHCI USB adapter, and
	  worked with a USB PEN Drive inserted into the first USB port of
	  the PCCARD. A rather pointless thing to do, but useful for testing.

	  It is safe to say M here.

	  See also <http://www.elandigitalsystems.com/support/ufaq/u132linux.php>

config USB_SL811_HCD
	tristate "SL811HS HCD support"
	depends on USB
	help
	  The SL811HS is a single-port USB controller that supports either
	  host side or peripheral side roles.  Enable this option if your
	  board has this chip, and you want to use it as a host controller. 
	  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called sl811-hcd.

config USB_SL811_CS
	tristate "CF/PCMCIA support for SL811HS HCD"
	depends on USB_SL811_HCD && PCMCIA
	help
	  Wraps a PCMCIA driver around the SL811HS HCD, supporting the RATOC
	  REX-CFU1U CF card (often used with PDAs).  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called "sl811_cs".

config USB_R8A66597_HCD
	tristate "R8A66597 HCD suppoort"
	depends on USB
	help
	  The R8A66597 is a USB 2.0 host and peripheral controller.

	  Enable this option if your board has this chip, and you want
	  to use it as a host controller.  If unsure, say N.

	  To compile this driver as a module, choose M here: the
	  module will be called r8a66597-hcd.
Commit	Line	Data
1da177e4 LT	1	#
	2	# USB Host Controller Drivers
	3	#
	4	comment "USB Host Controller Drivers"
	5	depends on USB
	6
	7	config USB_EHCI_HCD
	8	tristate "EHCI HCD (USB 2.0) support"
76fa9a24	9	depends on USB && USB_ARCH_HAS_EHCI
1da177e4 LT	10	---help---
	11	The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
	12	"high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware.
	13	If your USB host controller supports USB 2.0, you will likely want to
b3c29d85 JJ	14	configure this Host Controller Driver. At the time of this writing,
	15	the primary implementation of EHCI is a chip from NEC, widely available
	16	in add-on PCI cards, but implementations are in the works from other
	17	vendors including Intel and Philips. Motherboard support is appearing.
1da177e4 LT	18
	19	EHCI controllers are packaged with "companion" host controllers (OHCI
	20	or UHCI) to handle USB 1.1 devices connected to root hub ports. Ports
b3c29d85	21	will connect to EHCI if the device is high speed, otherwise they
1da177e4 LT	22	connect to a companion controller. If you configure EHCI, you should
	23	probably configure the OHCI (for NEC and some other vendors) USB Host
	24	Controller Driver or UHCI (for Via motherboards) Host Controller
	25	Driver too.
	26
	27	You may want to read <file:Documentation/usb/ehci.txt>.
	28
	29	To compile this driver as a module, choose M here: the
	30	module will be called ehci-hcd.
	31
	32	config USB_EHCI_SPLIT_ISO
	33	bool "Full speed ISO transactions (EXPERIMENTAL)"
	34	depends on USB_EHCI_HCD && EXPERIMENTAL
	35	default n
	36	---help---
	37	This code is new and hasn't been used with many different
	38	EHCI or USB 2.0 transaction translator implementations.
	39	It should work for ISO-OUT transfers, like audio.
	40
	41	config USB_EHCI_ROOT_HUB_TT
	42	bool "Root Hub Transaction Translators (EXPERIMENTAL)"
	43	depends on USB_EHCI_HCD && EXPERIMENTAL
	44	---help---
	45	Some EHCI chips have vendor-specific extensions to integrate
	46	transaction translators, so that no OHCI or UHCI companion
	47	controller is needed. It's safe to say "y" even if your
	48	controller doesn't support this feature.
	49
ba47f66b DS	50	This supports the EHCI implementation that's originally
	51	from ARC, and has since changed hands a few times.
	52
	53	config USB_EHCI_TT_NEWSCHED
	54	bool "Improved Transaction Translator scheduling (EXPERIMENTAL)"
	55	depends on USB_EHCI_HCD && EXPERIMENTAL
	56	---help---
	57	This changes the periodic scheduling code to fill more of the low
	58	and full speed bandwidth available from the Transaction Translator
	59	(TT) in USB 2.0 hubs. Without this, only one transfer will be
	60	issued in each microframe, significantly reducing the number of
	61	periodic low/fullspeed transfers possible.
	62
	63	If you have multiple periodic low/fullspeed devices connected to a
	64	highspeed USB hub which is connected to a highspeed USB Host
	65	Controller, and some of those devices will not work correctly
	66	(possibly due to "ENOSPC" or "-28" errors), say Y.
	67
	68	If unsure, say N.
1da177e4	69
083522d7 BH	70	config USB_EHCI_BIG_ENDIAN_MMIO
	71	bool
	72	depends on USB_EHCI_HCD
	73	default n
	74
6dbd682b SR	75	config USB_EHCI_BIG_ENDIAN_DESC
	76	bool
	77	depends on USB_EHCI_HCD
	78	default n
	79
4808a1c0 OK	80	config USB_ISP116X_HCD
	81	tristate "ISP116X HCD support"
	82	depends on USB
4808a1c0 OK	83	---help---
	84	The ISP1160 and ISP1161 chips are USB host controllers. Enable this
	85	option if your board has this chip. If unsure, say N.
	86
	87	This driver does not support isochronous transfers.
	88
	89	To compile this driver as a module, choose M here: the
	90	module will be called isp116x-hcd.
	91
1da177e4 LT	92	config USB_OHCI_HCD
	93	tristate "OHCI HCD support"
	94	depends on USB && USB_ARCH_HAS_OHCI
	95	select ISP1301_OMAP if MACH_OMAP_H2 \|\| MACH_OMAP_H3
60bbfc84	96	select I2C if ARCH_PNX4008
1da177e4 LT	97	---help---
	98	The Open Host Controller Interface (OHCI) is a standard for accessing
	99	USB 1.1 host controller hardware. It does more in hardware than Intel's
	100	UHCI specification. If your USB host controller follows the OHCI spec,
	101	say Y. On most non-x86 systems, and on x86 hardware that's not using a
	102	USB controller from Intel or VIA, this is appropriate. If your host
	103	controller doesn't use PCI, this is probably appropriate. For a PCI
	104	based system where you're not sure, the "lspci -v" entry will list the
	105	right "prog-if" for your USB controller(s): EHCI, OHCI, or UHCI.
	106
	107	To compile this driver as a module, choose M here: the
	108	module will be called ohci-hcd.
	109
	110	config USB_OHCI_HCD_PPC_SOC
	111	bool "OHCI support for on-chip PPC USB controller"
	112	depends on USB_OHCI_HCD && (STB03xxx \|\| PPC_MPC52xx)
	113	default y
11d1a4aa BH	114	select USB_OHCI_BIG_ENDIAN_DESC
11d1a4aa BH	115	select USB_OHCI_BIG_ENDIAN_MMIO
1da177e4 LT	116	---help---
	117	Enables support for the USB controller on the MPC52xx or
	118	STB03xxx processor chip. If unsure, say Y.
	119
495a678f SM	120	config USB_OHCI_HCD_PPC_OF
	121	bool "OHCI support for PPC USB controller on OF platform bus"
	122	depends on USB_OHCI_HCD && PPC_OF
	123	default y
	124	---help---
	125	Enables support for the USB controller PowerPC present on the
	126	OpenFirmware platform bus.
	127
	128	config USB_OHCI_HCD_PPC_OF_BE
	129	bool "Support big endian HC"
	130	depends on USB_OHCI_HCD_PPC_OF
	131	default y
	132	select USB_OHCI_BIG_ENDIAN_DESC
	133	select USB_OHCI_BIG_ENDIAN_MMIO
	134
	135	config USB_OHCI_HCD_PPC_OF_LE
	136	bool "Support little endian HC"
	137	depends on USB_OHCI_HCD_PPC_OF
	138	default n
	139	select USB_OHCI_LITTLE_ENDIAN
	140
1da177e4 LT	141	config USB_OHCI_HCD_PCI
1da177e4 LT	142	bool "OHCI support for PCI-bus USB controllers"
495a678f	143	depends on USB_OHCI_HCD && PCI && (STB03xxx \|\| PPC_MPC52xx \|\| USB_OHCI_HCD_PPC_OF)
1da177e4 LT	144	default y
	145	select USB_OHCI_LITTLE_ENDIAN
	146	---help---
	147	Enables support for PCI-bus plug-in USB controller cards.
	148	If unsure, say Y.
	149
11d1a4aa BH	150	config USB_OHCI_BIG_ENDIAN_DESC
	151	bool
	152	depends on USB_OHCI_HCD
	153	default n
	154
	155	config USB_OHCI_BIG_ENDIAN_MMIO
1da177e4 LT	156	bool
	157	depends on USB_OHCI_HCD
	158	default n
	159
	160	config USB_OHCI_LITTLE_ENDIAN
	161	bool
	162	depends on USB_OHCI_HCD
	163	default n if STB03xxx \|\| PPC_MPC52xx
	164	default y
	165
	166	config USB_UHCI_HCD
	167	tristate "UHCI HCD (most Intel and VIA) support"
	168	depends on USB && PCI
	169	---help---
	170	The Universal Host Controller Interface is a standard by Intel for
	171	accessing the USB hardware in the PC (which is also called the USB
	172	host controller). If your USB host controller conforms to this
	173	standard, you may want to say Y, but see below. All recent boards
	174	with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX,
	175	i810, i820) conform to this standard. Also all VIA PCI chipsets
	176	(like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro
	177	133). If unsure, say Y.
	178
	179	To compile this driver as a module, choose M here: the
	180	module will be called uhci-hcd.
	181
d774efea TO	182	config USB_U132_HCD
	183	tristate "Elan U132 Adapter Host Controller"
	184	depends on USB && USB_FTDI_ELAN
	185	default M
	186	help
	187	The U132 adapter is a USB to CardBus adapter specifically designed
	188	for PC cards that contain an OHCI host controller. Typical PC cards
	189	are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132
	190	adapter will NOT work with PC cards that do not contain an OHCI
	191	controller.
	192
3cb2fccc	193	For those PC cards that contain multiple OHCI controllers only the
d774efea TO	194	first one is used.
	195
	196	The driver consists of two modules, the "ftdi-elan" module is a
	197	USB client driver that interfaces to the FTDI chip within ELAN's
	198	USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host
	199	controller driver that talks to the OHCI controller within the
	200	CardBus cards that are inserted in the U132 adapter.
	201
	202	This driver has been tested with a CardBus OHCI USB adapter, and
	203	worked with a USB PEN Drive inserted into the first USB port of
	204	the PCCARD. A rather pointless thing to do, but useful for testing.
	205
	206	It is safe to say M here.
	207
	208	See also <http://www.elandigitalsystems.com/support/ufaq/u132linux.php>
	209
1da177e4 LT	210	config USB_SL811_HCD
	211	tristate "SL811HS HCD support"
	212	depends on USB
1da177e4 LT	213	help
	214	The SL811HS is a single-port USB controller that supports either
	215	host side or peripheral side roles. Enable this option if your
	216	board has this chip, and you want to use it as a host controller.
	217	If unsure, say N.
	218
	219	To compile this driver as a module, choose M here: the
	220	module will be called sl811-hcd.
	221
c6de2b64 DB	222	config USB_SL811_CS
	223	tristate "CF/PCMCIA support for SL811HS HCD"
	224	depends on USB_SL811_HCD && PCMCIA
c6de2b64 DB	225	help
	226	Wraps a PCMCIA driver around the SL811HS HCD, supporting the RATOC
	227	REX-CFU1U CF card (often used with PDAs). If unsure, say N.
	228
	229	To compile this driver as a module, choose M here: the
	230	module will be called "sl811_cs".
	231
5d304358 YS	232	config USB_R8A66597_HCD
	233	tristate "R8A66597 HCD suppoort"
	234	depends on USB
	235	help
	236	The R8A66597 is a USB 2.0 host and peripheral controller.
	237
	238	Enable this option if your board has this chip, and you want
	239	to use it as a host controller. If unsure, say N.
	240
	241	To compile this driver as a module, choose M here: the
	242	module will be called r8a66597-hcd.
	243