]> bbs.cooldavid.org Git - net-next-2.6.git/blame - drivers/serial/max3107.h
git://bbs.cooldavid.org / net-next-2.6.git / blame
? search:
summary | shortlog | log | commit | commitdiff | tree
blob | blame (incremental) | history | HEAD
pktgen: allow faster module unload
[net-next-2.6.git] / drivers / serial / max3107.h
CommitLineData
44318feb 1/*
2 * max3107.h - spi uart protocol driver header for Maxim 3107
3 *
4 * Copyright (C) Aavamobile 2009
5 * Based on serial_max3100.h by Christian Pellegrin
6 *
7 * This program is free software; you can redistribute it and/or modify
8 * it under the terms of the GNU General Public License as published by
9 * the Free Software Foundation; either version 2 of the License, or
10 * (at your option) any later version.
11 */
12
61fd1526
AC		 13#ifndef _MAX3107_H
14#define _MAX3107_H
44318feb 15
16/* Serial error status definitions */
17#define MAX3107_PARITY_ERROR 1
18#define MAX3107_FRAME_ERROR 2
19#define MAX3107_OVERRUN_ERROR 4
20#define MAX3107_ALL_ERRORS (MAX3107_PARITY_ERROR | \
21 MAX3107_FRAME_ERROR | \
22 MAX3107_OVERRUN_ERROR)
23
24/* GPIO definitions */
25#define MAX3107_GPIO_BASE 88
26#define MAX3107_GPIO_COUNT 4
27
28
29/* GPIO connected to chip's reset pin */
30#define MAX3107_RESET_GPIO 87
31
32
33/* Chip reset delay */
34#define MAX3107_RESET_DELAY 10
35
36/* Chip wakeup delay */
37#define MAX3107_WAKEUP_DELAY 50
38
39
40/* Sleep mode definitions */
41#define MAX3107_DISABLE_FORCED_SLEEP 0
42#define MAX3107_ENABLE_FORCED_SLEEP 1
43#define MAX3107_DISABLE_AUTOSLEEP 2
44#define MAX3107_ENABLE_AUTOSLEEP 3
45
46
47/* Definitions for register access with SPI transfers
48 *
49 * SPI transfer format:
50 *
51 * Master to slave bits xzzzzzzzyyyyyyyy
52 * Slave to master bits aaaaaaaabbbbbbbb
53 *
54 * where:
55 * x = 0 for reads, 1 for writes
56 * z = register address
57 * y = new register value if write, 0 if read
58 * a = unspecified
59 * b = register value if read, unspecified if write
60 */
61
62/* SPI speed */
63#define MAX3107_SPI_SPEED (3125000 * 2)
64
65/* Write bit */
66#define MAX3107_WRITE_BIT (1 << 15)
67
68/* SPI TX data mask */
69#define MAX3107_SPI_RX_DATA_MASK (0x00ff)
70
71/* SPI RX data mask */
72#define MAX3107_SPI_TX_DATA_MASK (0x00ff)
73
74/* Register access masks */
75#define MAX3107_RHR_REG (0x0000) /* RX FIFO */
76#define MAX3107_THR_REG (0x0000) /* TX FIFO */
77#define MAX3107_IRQEN_REG (0x0100) /* IRQ enable */
78#define MAX3107_IRQSTS_REG (0x0200) /* IRQ status */
79#define MAX3107_LSR_IRQEN_REG (0x0300) /* LSR IRQ enable */
80#define MAX3107_LSR_IRQSTS_REG (0x0400) /* LSR IRQ status */
81#define MAX3107_SPCHR_IRQEN_REG (0x0500) /* Special char IRQ enable */
82#define MAX3107_SPCHR_IRQSTS_REG (0x0600) /* Special char IRQ status */
83#define MAX3107_STS_IRQEN_REG (0x0700) /* Status IRQ enable */
84#define MAX3107_STS_IRQSTS_REG (0x0800) /* Status IRQ status */
85#define MAX3107_MODE1_REG (0x0900) /* MODE1 */
86#define MAX3107_MODE2_REG (0x0a00) /* MODE2 */
87#define MAX3107_LCR_REG (0x0b00) /* LCR */
88#define MAX3107_RXTO_REG (0x0c00) /* RX timeout */
89#define MAX3107_HDPIXDELAY_REG (0x0d00) /* Auto transceiver delays */
90#define MAX3107_IRDA_REG (0x0e00) /* IRDA settings */
91#define MAX3107_FLOWLVL_REG (0x0f00) /* Flow control levels */
92#define MAX3107_FIFOTRIGLVL_REG (0x1000) /* FIFO IRQ trigger levels */
93#define MAX3107_TXFIFOLVL_REG (0x1100) /* TX FIFO level */
94#define MAX3107_RXFIFOLVL_REG (0x1200) /* RX FIFO level */
95#define MAX3107_FLOWCTRL_REG (0x1300) /* Flow control */
96#define MAX3107_XON1_REG (0x1400) /* XON1 character */
97#define MAX3107_XON2_REG (0x1500) /* XON2 character */
98#define MAX3107_XOFF1_REG (0x1600) /* XOFF1 character */
99#define MAX3107_XOFF2_REG (0x1700) /* XOFF2 character */
100#define MAX3107_GPIOCFG_REG (0x1800) /* GPIO config */
101#define MAX3107_GPIODATA_REG (0x1900) /* GPIO data */
102#define MAX3107_PLLCFG_REG (0x1a00) /* PLL config */
103#define MAX3107_BRGCFG_REG (0x1b00) /* Baud rate generator conf */
104#define MAX3107_BRGDIVLSB_REG (0x1c00) /* Baud rate divisor LSB */
105#define MAX3107_BRGDIVMSB_REG (0x1d00) /* Baud rate divisor MSB */
106#define MAX3107_CLKSRC_REG (0x1e00) /* Clock source */
107#define MAX3107_REVID_REG (0x1f00) /* Revision identification */
108
109/* IRQ register bits */
110#define MAX3107_IRQ_LSR_BIT (1 << 0) /* LSR interrupt */
111#define MAX3107_IRQ_SPCHR_BIT (1 << 1) /* Special char interrupt */
112#define MAX3107_IRQ_STS_BIT (1 << 2) /* Status interrupt */
113#define MAX3107_IRQ_RXFIFO_BIT (1 << 3) /* RX FIFO interrupt */
114#define MAX3107_IRQ_TXFIFO_BIT (1 << 4) /* TX FIFO interrupt */
115#define MAX3107_IRQ_TXEMPTY_BIT (1 << 5) /* TX FIFO empty interrupt */
116#define MAX3107_IRQ_RXEMPTY_BIT (1 << 6) /* RX FIFO empty interrupt */
117#define MAX3107_IRQ_CTS_BIT (1 << 7) /* CTS interrupt */
118
119/* LSR register bits */
120#define MAX3107_LSR_RXTO_BIT (1 << 0) /* RX timeout */
121#define MAX3107_LSR_RXOVR_BIT (1 << 1) /* RX overrun */
122#define MAX3107_LSR_RXPAR_BIT (1 << 2) /* RX parity error */
123#define MAX3107_LSR_FRERR_BIT (1 << 3) /* Frame error */
124#define MAX3107_LSR_RXBRK_BIT (1 << 4) /* RX break */
125#define MAX3107_LSR_RXNOISE_BIT (1 << 5) /* RX noise */
126#define MAX3107_LSR_UNDEF6_BIT (1 << 6) /* Undefined/not used */
127#define MAX3107_LSR_CTS_BIT (1 << 7) /* CTS pin state */
128
129/* Special character register bits */
130#define MAX3107_SPCHR_XON1_BIT (1 << 0) /* XON1 character */
131#define MAX3107_SPCHR_XON2_BIT (1 << 1) /* XON2 character */
132#define MAX3107_SPCHR_XOFF1_BIT (1 << 2) /* XOFF1 character */
133#define MAX3107_SPCHR_XOFF2_BIT (1 << 3) /* XOFF2 character */
134#define MAX3107_SPCHR_BREAK_BIT (1 << 4) /* RX break */
135#define MAX3107_SPCHR_MULTIDROP_BIT (1 << 5) /* 9-bit multidrop addr char */
136#define MAX3107_SPCHR_UNDEF6_BIT (1 << 6) /* Undefined/not used */
137#define MAX3107_SPCHR_UNDEF7_BIT (1 << 7) /* Undefined/not used */
138
139/* Status register bits */
140#define MAX3107_STS_GPIO0_BIT (1 << 0) /* GPIO 0 interrupt */
141#define MAX3107_STS_GPIO1_BIT (1 << 1) /* GPIO 1 interrupt */
142#define MAX3107_STS_GPIO2_BIT (1 << 2) /* GPIO 2 interrupt */
143#define MAX3107_STS_GPIO3_BIT (1 << 3) /* GPIO 3 interrupt */
144#define MAX3107_STS_UNDEF4_BIT (1 << 4) /* Undefined/not used */
145#define MAX3107_STS_CLKREADY_BIT (1 << 5) /* Clock ready */
146#define MAX3107_STS_SLEEP_BIT (1 << 6) /* Sleep interrupt */
147#define MAX3107_STS_UNDEF7_BIT (1 << 7) /* Undefined/not used */
148
149/* MODE1 register bits */
150#define MAX3107_MODE1_RXDIS_BIT (1 << 0) /* RX disable */
151#define MAX3107_MODE1_TXDIS_BIT (1 << 1) /* TX disable */
152#define MAX3107_MODE1_TXHIZ_BIT (1 << 2) /* TX pin three-state */
153#define MAX3107_MODE1_RTSHIZ_BIT (1 << 3) /* RTS pin three-state */
154#define MAX3107_MODE1_TRNSCVCTRL_BIT (1 << 4) /* Transceiver ctrl enable */
155#define MAX3107_MODE1_FORCESLEEP_BIT (1 << 5) /* Force sleep mode */
156#define MAX3107_MODE1_AUTOSLEEP_BIT (1 << 6) /* Auto sleep enable */
157#define MAX3107_MODE1_IRQSEL_BIT (1 << 7) /* IRQ pin enable */
158
159/* MODE2 register bits */
160#define MAX3107_MODE2_RST_BIT (1 << 0) /* Chip reset */
161#define MAX3107_MODE2_FIFORST_BIT (1 << 1) /* FIFO reset */
162#define MAX3107_MODE2_RXTRIGINV_BIT (1 << 2) /* RX FIFO INT invert */
163#define MAX3107_MODE2_RXEMPTINV_BIT (1 << 3) /* RX FIFO empty INT invert */
164#define MAX3107_MODE2_SPCHR_BIT (1 << 4) /* Special chr detect enable */
165#define MAX3107_MODE2_LOOPBACK_BIT (1 << 5) /* Internal loopback enable */
166#define MAX3107_MODE2_MULTIDROP_BIT (1 << 6) /* 9-bit multidrop enable */
167#define MAX3107_MODE2_ECHOSUPR_BIT (1 << 7) /* ECHO suppression enable */
168
169/* LCR register bits */
170#define MAX3107_LCR_LENGTH0_BIT (1 << 0) /* Word length bit 0 */
171#define MAX3107_LCR_LENGTH1_BIT (1 << 1) /* Word length bit 1
172 *
173 * Word length bits table:
174 * 00 -> 5 bit words
175 * 01 -> 6 bit words
176 * 10 -> 7 bit words
177 * 11 -> 8 bit words
178 */
179#define MAX3107_LCR_STOPLEN_BIT (1 << 2) /* STOP length bit
180 *
181 * STOP length bit table:
182 * 0 -> 1 stop bit
183 * 1 -> 1-1.5 stop bits if
184 * word length is 5,
185 * 2 stop bits otherwise
186 */
187#define MAX3107_LCR_PARITY_BIT (1 << 3) /* Parity bit enable */
188#define MAX3107_LCR_EVENPARITY_BIT (1 << 4) /* Even parity bit enable */
189#define MAX3107_LCR_FORCEPARITY_BIT (1 << 5) /* 9-bit multidrop parity */
190#define MAX3107_LCR_TXBREAK_BIT (1 << 6) /* TX break enable */
191#define MAX3107_LCR_RTS_BIT (1 << 7) /* RTS pin control */
192#define MAX3107_LCR_WORD_LEN_5 (0x0000)
193#define MAX3107_LCR_WORD_LEN_6 (0x0001)
194#define MAX3107_LCR_WORD_LEN_7 (0x0002)
195#define MAX3107_LCR_WORD_LEN_8 (0x0003)
196
197
198/* IRDA register bits */
199#define MAX3107_IRDA_IRDAEN_BIT (1 << 0) /* IRDA mode enable */
200#define MAX3107_IRDA_SIR_BIT (1 << 1) /* SIR mode enable */
201#define MAX3107_IRDA_SHORTIR_BIT (1 << 2) /* Short SIR mode enable */
202#define MAX3107_IRDA_MIR_BIT (1 << 3) /* MIR mode enable */
203#define MAX3107_IRDA_RXINV_BIT (1 << 4) /* RX logic inversion enable */
204#define MAX3107_IRDA_TXINV_BIT (1 << 5) /* TX logic inversion enable */
205#define MAX3107_IRDA_UNDEF6_BIT (1 << 6) /* Undefined/not used */
206#define MAX3107_IRDA_UNDEF7_BIT (1 << 7) /* Undefined/not used */
207
208/* Flow control trigger level register masks */
209#define MAX3107_FLOWLVL_HALT_MASK (0x000f) /* Flow control halt level */
210#define MAX3107_FLOWLVL_RES_MASK (0x00f0) /* Flow control resume level */
211#define MAX3107_FLOWLVL_HALT(words) ((words/8) & 0x000f)
212#define MAX3107_FLOWLVL_RES(words) (((words/8) & 0x000f) << 4)
213
214/* FIFO interrupt trigger level register masks */
215#define MAX3107_FIFOTRIGLVL_TX_MASK (0x000f) /* TX FIFO trigger level */
216#define MAX3107_FIFOTRIGLVL_RX_MASK (0x00f0) /* RX FIFO trigger level */
217#define MAX3107_FIFOTRIGLVL_TX(words) ((words/8) & 0x000f)
218#define MAX3107_FIFOTRIGLVL_RX(words) (((words/8) & 0x000f) << 4)
219
220/* Flow control register bits */
221#define MAX3107_FLOWCTRL_AUTORTS_BIT (1 << 0) /* Auto RTS flow ctrl enable */
222#define MAX3107_FLOWCTRL_AUTOCTS_BIT (1 << 1) /* Auto CTS flow ctrl enable */
223#define MAX3107_FLOWCTRL_GPIADDR_BIT (1 << 2) /* Enables that GPIO inputs
224 * are used in conjunction with
225 * XOFF2 for definition of
226 * special character */
227#define MAX3107_FLOWCTRL_SWFLOWEN_BIT (1 << 3) /* Auto SW flow ctrl enable */
228#define MAX3107_FLOWCTRL_SWFLOW0_BIT (1 << 4) /* SWFLOW bit 0 */
229#define MAX3107_FLOWCTRL_SWFLOW1_BIT (1 << 5) /* SWFLOW bit 1
230 *
231 * SWFLOW bits 1 & 0 table:
232 * 00 -> no transmitter flow
233 * control
234 * 01 -> receiver compares
235 * XON2 and XOFF2
236 * and controls
237 * transmitter
238 * 10 -> receiver compares
239 * XON1 and XOFF1
240 * and controls
241 * transmitter
242 * 11 -> receiver compares
243 * XON1, XON2, XOFF1 and
244 * XOFF2 and controls
245 * transmitter
246 */
247#define MAX3107_FLOWCTRL_SWFLOW2_BIT (1 << 6) /* SWFLOW bit 2 */
248#define MAX3107_FLOWCTRL_SWFLOW3_BIT (1 << 7) /* SWFLOW bit 3
249 *
250 * SWFLOW bits 3 & 2 table:
251 * 00 -> no received flow
252 * control
253 * 01 -> transmitter generates
254 * XON2 and XOFF2
255 * 10 -> transmitter generates
256 * XON1 and XOFF1
257 * 11 -> transmitter generates
258 * XON1, XON2, XOFF1 and
259 * XOFF2
260 */
261
262/* GPIO configuration register bits */
263#define MAX3107_GPIOCFG_GP0OUT_BIT (1 << 0) /* GPIO 0 output enable */
264#define MAX3107_GPIOCFG_GP1OUT_BIT (1 << 1) /* GPIO 1 output enable */
265#define MAX3107_GPIOCFG_GP2OUT_BIT (1 << 2) /* GPIO 2 output enable */
266#define MAX3107_GPIOCFG_GP3OUT_BIT (1 << 3) /* GPIO 3 output enable */
267#define MAX3107_GPIOCFG_GP0OD_BIT (1 << 4) /* GPIO 0 open-drain enable */
268#define MAX3107_GPIOCFG_GP1OD_BIT (1 << 5) /* GPIO 1 open-drain enable */
269#define MAX3107_GPIOCFG_GP2OD_BIT (1 << 6) /* GPIO 2 open-drain enable */
270#define MAX3107_GPIOCFG_GP3OD_BIT (1 << 7) /* GPIO 3 open-drain enable */
271
272/* GPIO DATA register bits */
273#define MAX3107_GPIODATA_GP0OUT_BIT (1 << 0) /* GPIO 0 output value */
274#define MAX3107_GPIODATA_GP1OUT_BIT (1 << 1) /* GPIO 1 output value */
275#define MAX3107_GPIODATA_GP2OUT_BIT (1 << 2) /* GPIO 2 output value */
276#define MAX3107_GPIODATA_GP3OUT_BIT (1 << 3) /* GPIO 3 output value */
277#define MAX3107_GPIODATA_GP0IN_BIT (1 << 4) /* GPIO 0 input value */
278#define MAX3107_GPIODATA_GP1IN_BIT (1 << 5) /* GPIO 1 input value */
279#define MAX3107_GPIODATA_GP2IN_BIT (1 << 6) /* GPIO 2 input value */
280#define MAX3107_GPIODATA_GP3IN_BIT (1 << 7) /* GPIO 3 input value */
281
282/* PLL configuration register masks */
283#define MAX3107_PLLCFG_PREDIV_MASK (0x003f) /* PLL predivision value */
284#define MAX3107_PLLCFG_PLLFACTOR_MASK (0x00c0) /* PLL multiplication factor */
285
286/* Baud rate generator configuration register masks and bits */
287#define MAX3107_BRGCFG_FRACT_MASK (0x000f) /* Fractional portion of
288 * Baud rate generator divisor
289 */
290#define MAX3107_BRGCFG_2XMODE_BIT (1 << 4) /* Double baud rate */
291#define MAX3107_BRGCFG_4XMODE_BIT (1 << 5) /* Quadruple baud rate */
292#define MAX3107_BRGCFG_UNDEF6_BIT (1 << 6) /* Undefined/not used */
293#define MAX3107_BRGCFG_UNDEF7_BIT (1 << 7) /* Undefined/not used */
294
295/* Clock source register bits */
296#define MAX3107_CLKSRC_INTOSC_BIT (1 << 0) /* Internal osc enable */
297#define MAX3107_CLKSRC_CRYST_BIT (1 << 1) /* Crystal osc enable */
298#define MAX3107_CLKSRC_PLL_BIT (1 << 2) /* PLL enable */
299#define MAX3107_CLKSRC_PLLBYP_BIT (1 << 3) /* PLL bypass */
300#define MAX3107_CLKSRC_EXTCLK_BIT (1 << 4) /* External clock enable */
301#define MAX3107_CLKSRC_UNDEF5_BIT (1 << 5) /* Undefined/not used */
302#define MAX3107_CLKSRC_UNDEF6_BIT (1 << 6) /* Undefined/not used */
303#define MAX3107_CLKSRC_CLK2RTS_BIT (1 << 7) /* Baud clk to RTS pin */
304
305
306/* HW definitions */
307#define MAX3107_RX_FIFO_SIZE 128
308#define MAX3107_TX_FIFO_SIZE 128
309#define MAX3107_REVID1 0x00a0
310#define MAX3107_REVID2 0x00a1
311
312
313/* Baud rate generator configuration values for external clock 13MHz */
314#define MAX3107_BRG13_B300 (0x0A9400 | 0x05)
315#define MAX3107_BRG13_B600 (0x054A00 | 0x03)
316#define MAX3107_BRG13_B1200 (0x02A500 | 0x01)
317#define MAX3107_BRG13_B2400 (0x015200 | 0x09)
318#define MAX3107_BRG13_B4800 (0x00A900 | 0x04)
319#define MAX3107_BRG13_B9600 (0x005400 | 0x0A)
320#define MAX3107_BRG13_B19200 (0x002A00 | 0x05)
321#define MAX3107_BRG13_B38400 (0x001500 | 0x03)
322#define MAX3107_BRG13_B57600 (0x000E00 | 0x02)
323#define MAX3107_BRG13_B115200 (0x000700 | 0x01)
324#define MAX3107_BRG13_B230400 (0x000300 | 0x08)
325#define MAX3107_BRG13_B460800 (0x000100 | 0x0c)
326#define MAX3107_BRG13_B921600 (0x000100 | 0x1c)
327
328/* Baud rate generator configuration values for external clock 26MHz */
329#define MAX3107_BRG26_B300 (0x152800 | 0x0A)
330#define MAX3107_BRG26_B600 (0x0A9400 | 0x05)
331#define MAX3107_BRG26_B1200 (0x054A00 | 0x03)
332#define MAX3107_BRG26_B2400 (0x02A500 | 0x01)
333#define MAX3107_BRG26_B4800 (0x015200 | 0x09)
334#define MAX3107_BRG26_B9600 (0x00A900 | 0x04)
335#define MAX3107_BRG26_B19200 (0x005400 | 0x0A)
336#define MAX3107_BRG26_B38400 (0x002A00 | 0x05)
337#define MAX3107_BRG26_B57600 (0x001C00 | 0x03)
338#define MAX3107_BRG26_B115200 (0x000E00 | 0x02)
339#define MAX3107_BRG26_B230400 (0x000700 | 0x01)
340#define MAX3107_BRG26_B460800 (0x000300 | 0x08)
341#define MAX3107_BRG26_B921600 (0x000100 | 0x0C)
342
343/* Baud rate generator configuration values for internal clock */
344#define MAX3107_BRG13_IB300 (0x008000 | 0x00)
345#define MAX3107_BRG13_IB600 (0x004000 | 0x00)
346#define MAX3107_BRG13_IB1200 (0x002000 | 0x00)
347#define MAX3107_BRG13_IB2400 (0x001000 | 0x00)
348#define MAX3107_BRG13_IB4800 (0x000800 | 0x00)
349#define MAX3107_BRG13_IB9600 (0x000400 | 0x00)
350#define MAX3107_BRG13_IB19200 (0x000200 | 0x00)
351#define MAX3107_BRG13_IB38400 (0x000100 | 0x00)
352#define MAX3107_BRG13_IB57600 (0x000000 | 0x0B)
353#define MAX3107_BRG13_IB115200 (0x000000 | 0x05)
354#define MAX3107_BRG13_IB230400 (0x000000 | 0x03)
355#define MAX3107_BRG13_IB460800 (0x000000 | 0x00)
356#define MAX3107_BRG13_IB921600 (0x000000 | 0x00)
357
61fd1526
AC		 358
359struct baud_table {
360 int baud;
361 u32 new_brg;
362};
363
364struct max3107_port {
365 /* UART port structure */
366 struct uart_port port;
367
368 /* SPI device structure */
369 struct spi_device *spi;
370
e38018be 371#if defined(CONFIG_GPIOLIB)
61fd1526
AC		 372 /* GPIO chip stucture */
373 struct gpio_chip chip;
e38018be 374#endif
61fd1526
AC		 375
376 /* Workqueue that does all the magic */
377 struct workqueue_struct *workqueue;
378 struct work_struct work;
379
380 /* Lock for shared data */
381 spinlock_t data_lock;
382
383 /* Device configuration */
384 int ext_clk; /* 1 if external clock used */
385 int loopback; /* Current loopback mode state */
386 int baud; /* Current baud rate */
387
388 /* State flags */
389 int suspended; /* Indicates suspend mode */
390 int tx_fifo_empty; /* Flag for TX FIFO state */
391 int rx_enabled; /* Flag for receiver state */
392 int tx_enabled; /* Flag for transmitter state */
393
394 u16 irqen_reg; /* Current IRQ enable register value */
395 /* Shared data */
396 u16 mode1_reg; /* Current mode1 register value*/
397 int mode1_commit; /* Flag for setting new mode1 register value */
398 u16 lcr_reg; /* Current LCR register value */
399 int lcr_commit; /* Flag for setting new LCR register value */
400 u32 brg_cfg; /* Current Baud rate generator config */
401 int brg_commit; /* Flag for setting new baud rate generator
402 * config
403 */
404 struct baud_table *baud_tbl;
405 int handle_irq; /* Indicates that IRQ should be handled */
406
407 /* Rx buffer and str*/
408 u16 *rxbuf;
409 u8 *rxstr;
410 /* Tx buffer*/
411 u16 *txbuf;
412
413 struct max3107_plat *pdata; /* Platform data */
414};
415
416/* Platform data structure */
417struct max3107_plat {
418 /* Loopback mode enable */
419 int loopback;
420 /* External clock enable */
421 int ext_clk;
422 /* Called during the register initialisation */
423 void (*init)(struct max3107_port *s);
424 /* Called when the port is found and configured */
425 int (*configure)(struct max3107_port *s);
426 /* HW suspend function */
427 void (*hw_suspend) (struct max3107_port *s, int suspend);
428 /* Polling mode enable */
429 int polled_mode;
430 /* Polling period if polling mode enabled */
431 int poll_time;
432};
433
434extern int max3107_rw(struct max3107_port *s, u8 *tx, u8 *rx, int len);
435extern void max3107_hw_susp(struct max3107_port *s, int suspend);
436extern int max3107_probe(struct spi_device *spi, struct max3107_plat *pdata);
437extern int max3107_remove(struct spi_device *spi);
438extern int max3107_suspend(struct spi_device *spi, pm_message_t state);
439extern int max3107_resume(struct spi_device *spi);
440
44318feb 441#endif /* _LINUX_SERIAL_MAX3107_H */
Clone of davem's net-next-2.6 tree