John W. Linville [Thu, 25 Feb 2010 17:02:45 +0000 (12:02 -0500)]
netdevice.h: check for CONFIG_WLAN instead of CONFIG_WLAN_80211
In "wireless: remove WLAN_80211 and WLAN_PRE80211 from Kconfig" I
inadvertantly missed a line in include/linux/netdevice.h. I thereby
effectively reverted "net: Set LL_MAX_HEADER properly for wireless." by
accident. :-( Now we should check there for CONFIG_WLAN instead.
Signed-off-by: John W. Linville <linville@tuxdriver.com> Reported-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de> Cc: stable@kernel.org
Helmut Schaa [Wed, 24 Feb 2010 13:19:37 +0000 (14:19 +0100)]
mac80211: use listen interval 5 as default
Currently if a driver does not set hw.max_listen_interval a listen
interval of 1 is negotiated with the AP. Thus, the AP could drop
buffered frames for us after just one beacon interval which can
easily happen with the current powersave and scan implementation.
To avoid this issue increase the default interval to 5 which should
be a reasonable safe default.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 24 Feb 2010 03:43:05 +0000 (04:43 +0100)]
ath9k: disable RIFS search for AR91xx based chips
While ath9k does not support RIFS yet, the ability to receive RIFS
frames is currently enabled for most chipsets in the initvals.
This is causing baseband related issues on AR9160 and AR9130 based
chipsets, which can lock up under certain conditions.
This patch fixes these issues by overriding the initvals, effectively
disabling RIFS for all affected chipsets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Abhijeet Kolekar [Fri, 19 Feb 2010 19:49:49 +0000 (11:49 -0800)]
iwlwifi: increase command buffer size
Increase the buffer size for commands with "huge"
bit set. This has been recently observed for 6050 cards where
for even with huge bit set few commands were not properly allocated
memory with the command overwriting the buffer allocated for it..
Also add a check to see if command size exceeds the
maximum allowable size.
The goal of "iwlwifi: Monitor and recover the aggregation TX flow failure"
is to first detect when data transmission stalls and then to recover from
this situation with a reset of the radio or the firmware, depending on how
bad the transmission failures are.
Unfortunately we have found that this change causes excessive resets with
its current detection algorithm. It also performs its recovery action when
none is really needed, like when we are not associated.
Revert this change until the issues have been addressed.
Johannes Berg [Fri, 19 Feb 2010 18:18:37 +0000 (19:18 +0100)]
mwl8k: convert to new station add/remove callbacks
This converts mwl8k to use the new station
add/remove callbacks instead of using the
old sta_notify callback.
The new callbacks can sleep, so a lot of
code can be removed now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: sanity check before counting number of tfds can be free
Check the frame control for ieee80211_is_data_qos() is true before
counting the number of tfds can be free, the tfds_in_queue only
increment when ieee80211_is_data_qos() is true before transmit; so it
should only decrement if the type match.
Remove ieee80211_is_data_qos check for frame_ctrl in tx_resp to avoid
invalid information pass from uCode.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> CC: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 19 Feb 2010 23:47:32 +0000 (15:47 -0800)]
iwlwifi: error checking for number of tfds in queue
When receive reply_tx and ready to decrement the count for number of
tfds in queue, do error checking to prevent error condition and
tfds_in_queue become negative number.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> CC: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 19 Feb 2010 17:21:42 +0000 (18:21 +0100)]
ath9k: fix beacon timer restart after a card reset
In AP mode, ath_beacon_config_ap only restarts the timer if a TSF
restart is requested. Apparently this was added, because this function
unconditionally sets the flag for TSF reset.
The problem with this is, that ath9k_hw_reset() clobbers the timer
registers (specified in the initvals), thus effectively disabling the
SWBA interrupt whenever a card reset without TSF reset is issued
(happens in a few places in the code).
This patch fixes ath_beacon_config_ap to only issue the TSF reset flag
when necessary, but reinitialize the timer unconditionally. Tests show,
that this is enough to keep the SWBA interrupt going after a call to
ath_reset()
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 19 Feb 2010 06:03:07 +0000 (22:03 -0800)]
iwlwifi: add debugfs to monitor force reset parameters
Adding debugfs file to monitor the counters and other
information related to "force_reset" request.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 19 Feb 2010 06:03:06 +0000 (22:03 -0800)]
iwlwifi: separated time check for different type of force reset
Use different timing duration check for different type of force reset,
force reset request can come from different source and based on
different reason; one type of reset request should not block other type of
reset request.
Adding structure to keep track of different force reset request.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Fri, 19 Feb 2010 06:03:04 +0000 (22:03 -0800)]
iwlwifi: enable serialization of synchronous commands
Until now it was only possible to have one synchronous command running at
any time. If a synchronous command is in progress when a second request
arrives then the second command will fail. Create a new mutex specific for
this purpose to only allow one synchronous command at a time, but enable
other commands to wait instead of fail if a synchronous command is in
progress.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Fri, 19 Feb 2010 06:03:02 +0000 (22:03 -0800)]
iwl3945: remove STATUS macros from header
iwl3945 includes iwl-core.h in which these STATUS flags are already
defined. This also removes a potential confusing definition with iwlcore
using STATUS_MODE_PENDING with value 18 and iwl3945 defining (but not
using) STATUS_CONF_PENDING for value 18.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 19 Feb 2010 00:46:36 +0000 (01:46 +0100)]
ath9k: fix rate control fallback rate selection
When selecting the tx fallback rate, rc.c used a separate variable
'nrix' for storing the next rate index, however it did not use that as
reference for further rate index lowering. Because of that, it ended up
reusing the same rate for multiple multi-rate retry stages, thus
decreasing delivery probability under changing link conditions.
This patch removes the separate (unnecessary) variable and fixes
fallback the way it was intended to work.
This should result in increased throughput and better link stability.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Thu, 18 Feb 2010 11:25:53 +0000 (13:25 +0200)]
wl1271: add testmode support
Testmode will be used to send PLT (Production Line Testing) commands
from user space.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Feb 2010 11:25:52 +0000 (13:25 +0200)]
wl1271: Fix beacon filter table configuration
The beacon filter table configuration ACX structure had certain elements
reversed, resulting in firmware instability in regard of the feature. Fix
the structure.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Feb 2010 11:25:51 +0000 (13:25 +0200)]
wl1271: Fix ad-hoc SSID update
If re-configuring the SSID while ad-hoc was already enabled, the beacon
template would be properly updated, but the SSID passed in the CMD_JOIN would
not - hence filtering etc would not work properly.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Feb 2010 11:25:50 +0000 (13:25 +0200)]
wl1271: Fix WEP key handling
WEP key index handling was broken: the default key when using key 0 was never
specified to the FW, and if using other default than 0, it would be set on the
TX path for every single TX'd frame.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Feb 2010 11:25:49 +0000 (13:25 +0200)]
wl1271: Fix key-remove error
The new firmware does not allow removal of unicast keys - they will be
automatically removed on the next CMD_JOIN.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Feb 2010 11:25:48 +0000 (13:25 +0200)]
wl1271: Optimized RX path packet retrieval
Instead of acking RX packets read from the FW once all (of several possible)
buffered packets are retrieved, ack packets one by one as they are read. This
enables the FW to start receiving more packets from the network while the
host read operation is still ongoing.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Thu, 18 Feb 2010 11:25:47 +0000 (13:25 +0200)]
wl1271: wakeup chip in op_conf_tx()
elp_wakeup() was missing in op_conf_tx() which caused wakeup problems in
power save. I forgot to add this part when porting the patch from wl1251.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Feb 2010 11:25:46 +0000 (13:25 +0200)]
wl1271: Fix random MAC address setting
If reverting to a random MAC address, the driver would not update it to the
NVS file, and hence the firmware frame filtering would not work properly.
So update the randomized MAC address to the NVS image.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Thu, 18 Feb 2010 11:25:45 +0000 (13:25 +0200)]
wl1271: skip 3 unused bytes from the NVS
Our NVS uploading mechanism had a bug that was causing it to pass three extra
zeros at the start of the NVS. This may be a problem in the NVS generation
application, but for now we fix it in the driver.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Thu, 18 Feb 2010 11:25:44 +0000 (13:25 +0200)]
wl1271: add most of the normal initialization commands to PLT mode
We need to configure PLT mode almost in the same way as normal mode. Most of
the configuration functions need to be called also when entering PLT, with
the exception of a few RX and TX configuration (which cause mac80211 warnings
if enable while runnning PLT tests).
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Feb 2010 11:25:43 +0000 (13:25 +0200)]
wl1271: Retrieve device mac address from the nvs file
Instead of always randomizing the MAC address, retrieve and configure the
MAC address from the device specific nvs file. For now, randomize an address
only if the address in the NVS is zero.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Feb 2010 11:25:42 +0000 (13:25 +0200)]
wl1271: Use NVS INI file configuration
Replace the hardcoded general and radio parameter configuration in the driver
with configuration taken from the NVS file directly. Also remove the driver
dependency to the structures with the parameter data.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Thu, 18 Feb 2010 11:25:41 +0000 (13:25 +0200)]
wl1271: implement WMM
Now that necessary commands for WMM are implemented, implement queue handling
for WMM. But WMM is not enabled yet, only one queue is used.
Based on a similar patch from wl1251.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Thu, 18 Feb 2010 11:25:40 +0000 (13:25 +0200)]
wl1271: modify wl1271_acx_tid_cfg() to use function parameters
For WMM we need to configure each tid separately so modify
wl1271_acx_tid_cfg() to take the configuration from function parameters
instead.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Thu, 18 Feb 2010 11:25:39 +0000 (13:25 +0200)]
wl1271: modify wl1271_acx_ac_cfg() to use function parameters
For WMM we need to configure each queue separately so modify
wl1271_acx_ac_cfg() to take the configuration from function parameters
instead.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Feb 2010 11:25:38 +0000 (13:25 +0200)]
wl1271: Add SSID configuration for JOIN in ad-hoc
This patch adds code to extract the SSID from the beacon template used for
ad-hoc. The mac80211 currently does not provide the SSID, so this is a
workaround for that, for now.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Feb 2010 11:25:37 +0000 (13:25 +0200)]
wl1271: Fix channel changing code
The channel changing code would a) change the BSSID to a dummy on upon
channel change, breaking connectivity, and b) not update the channel number
at all for ad-hoc, breaking adhoc.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Feb 2010 11:25:36 +0000 (13:25 +0200)]
wl1271: Fix PSM entry
Currently the PSM entry function assumes successful operation, and enables
ELP, BET and beacon filtering right away. This is bad, because the PSM
entry may fail due to environmental issues, which will cause the ELP, BET and
beacon filtering to be illegally enabled (because FW remains in active state.)
Fix this by enabling ELP, BET and beacon filtering only after successful entry,
and by ensuring the firmware is in active mode after the failure.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Frederic Leroy [Wed, 17 Feb 2010 23:25:26 +0000 (00:25 +0100)]
staging: rtl8192su: fix compile error from wireless-testing commit
In wireless-testing, commit 7044cc56 added struct ieee80211_hdr_3addr
to include/linux/ieee80211.h. This definition collides with one that is
in the rtl8192su driver in staging.
The conflict is resolved by changing rtl8192su
to use the definition from include/linux/ieee80211.h.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Wed, 17 Feb 2010 15:58:10 +0000 (17:58 +0200)]
nl80211: add power save commands
The most needed command from nl80211, which Wireless Extensions had,
is support for power save mode. Add a simple command to make it possible
to enable and disable power save via nl80211.
I was also planning about extending the interface, for example adding the
timeout value, but after thinking more about this I decided not to do it.
Basically there were three reasons:
Firstly, the parameters for power save are very much hardware dependent.
Trying to find a unified interface which would work with all hardware, and
still make sense to users, will be very difficult.
Secondly, IEEE 802.11 power save implementation in Linux is still in state
of flux. We have a long way to still to go and there is no way to predict
what kind of implementation we will have after few years. And because we
need to support nl80211 interface a long time, practically forever, adding
now parameters to nl80211 might create maintenance problems later on.
Third issue are the users. Power save parameters are mostly used for
debugging, so debugfs is better, more flexible, interface for this.
For example, wpa_supplicant currently doesn't configure anything related
to power save mode. It's better to strive that kernel can automatically
optimise the power save parameters, like with help of pm qos network
and other traffic parameters.
Later on, when we have better understanding of power save, we can extend
this command with more features, if there's a need for that.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
As it's the case with some other Prism based devices, the third ID
string contains a design name that should be sufficient to identify the
card as having Intersil Prism chipset and thus compatible with both
orinoco_cs and hostap_cs.
Introduce PCMCIA_DEVICE_PROD_ID3 that matches the third ID string only.
Use it in orinoco_cs and hostap_cs to match cards with the third ID
string indicating Prism chipset. Remove corresponding entries that use
PCMCIA_DEVICE_PROD_ID123.
Reported-by: Ozzy <ozzymud@gmail.com> Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Halperin [Fri, 19 Feb 2010 06:01:39 +0000 (22:01 -0800)]
iwlwifi: set HT flags after channel in rxon
The HT extension channel settings require priv->staging_rxon.channel to be
accurate. However, iwl_set_rxon_ht was being called before iwl_set_rxon_channel
and thus HT40 could be broken unless another call to iwl_mac_config came in.
This problem was recently introduced by "iwlwifi: Fix to set correct ht
configuration"
The particular setting in which I noticed this was monitor mode:
iwconfig wlan0 mode monitor
ifconfig wlan0 up
./iw wlan0 set channel 64 HT40-
#./iw wlan0 set channel 64 HT40-
tcpdump -i wlan0 -y IEEE802_11_RADIO
would only catch HT40 packets if I issued the IW command twice.
From visual inspection, iwl_set_rxon_channel does not depend on
iwl_set_rxon_ht, so simply swapping them should be safe and fixes this problem.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> CC: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 16 Feb 2010 10:05:00 +0000 (11:05 +0100)]
mac80211: split ieee80211_drop_unencrypted
Currently, ieee80211_drop_unencrypted is called
from management and data frame context, and the
different contexts pass different frames. This
could lead to it processing an 802.3 frame as an
802.11 frame when MFP is enabled.
Move the MFP part of ieee80211_drop_unencrypted
into a new function that is only called for mgmt
frames.
Cc: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin [Sun, 14 Feb 2010 03:13:06 +0000 (22:13 -0500)]
mwl8k: disable softirqs when accessing sta_notify_list
Use spin_[un]lock_bh in mwl8k_sta_notify(). The sta_notify handler is
required to be atomic, yet it can be called in process context, so make
sure one call won't preempt another.
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Mon, 15 Feb 2010 10:53:10 +0000 (12:53 +0200)]
cfg80211/mac80211: allow registering for and sending action frames
This implements a new command to register for action frames
that userspace wants to handle instead of the in-kernel
rejection. It is then responsible for rejecting ones that
it decided not to handle. There is no unregistration, but
the socket can be closed for that.
Frames that are not registered for will not be forwarded
to userspace and will be rejected by the kernel, the
cfg80211 API helps implementing that.
Additionally, this patch adds a new command that allows
doing action frame transmission from userspace. It can be
used either to exchange action frames on the current
operational channel (e.g., with the AP with which we are
currently associated) or to exchange off-channel Public
Action frames with the remain-on-channel command.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 15 Feb 2010 10:46:39 +0000 (12:46 +0200)]
mac80211: reject unhandled action frames
802.11-2007 7.3.1.11 mandates that we need to
reject action frames we don't handle by setting
the 0x80 bit in the category and returning them
to the sender, so do that. In AP mode, hostapd
is responsible for this.
Additionally, drop completely malformed action
frames or ones that should've been encrypted as
unusable, userspace shouldn't see those.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: rt2800 - Make rt30xx and rt35xx chipsets configurable.
Support for rt30xx- and rt35xx-based devices is currently not functional
in rt2800pci and rt2800usb.
In order to not confuse users we shouldn't claim the PCI and USB device
ID's for these devices. However, to allow for testing it is good to still
have them available, although disabled by default.
Make support for these device configuration options that default to off.
For rt2800usb a 3rd class of devices is added, which are the unknown
devices. For these devices it is known that they are either based on
rt28xx, rt30xx or rt35xx, but it is not known on what chipset exactly.
These devices are disabled by default as well, until it can be established
on what chipset exactly they are based.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: rework RT chipset and revision determination for PCI an SOC devices.
The recent rt2800 devices are no longer really identified by their PCI
ID's, but rather by the contents of their CSR0 register. Also for the
other chipsets is the contents of this CSR0 register important.
Change the chipset determination logic to be more aligned with the rt2800
model.
Preparation for the support of rt3070 / rt3090 based devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: Reorganize RT chipset setting for PCI/SOC devices.
Don't set the RT chipset for a device from within the generic PCI/SOC code,
but rather from the individual drivers, so that individual drivers have
more control over what RT chipset is set.
Preparation for chip handling updates for rt2800 devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce the SoC interface type to detect SoC devices, instead of having
them mimic being PCI devices.
This allows for easier detection of SoC devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Randy Dunlap [Fri, 12 Feb 2010 21:02:23 +0000 (13:02 -0800)]
wireless: airo_cs build fixes
When WEXT_PRIV is not enabled, airo_cs has build errors.
It needs to include net/iw_handler.h and it should select
WEXT_PRIV, like the airo driver does.
drivers/net/wireless/airo.c:7655: error: unknown field 'num_private' specified in initializer
drivers/net/wireless/airo.c:7655: warning: initialization makes pointer from integer without a cast
drivers/net/wireless/airo.c:7656: error: unknown field 'num_private_args' specified in initializer
drivers/net/wireless/airo.c:7656: warning: excess elements in struct initializer
drivers/net/wireless/airo.c:7656: warning: (near initialization for 'airo_handler_def')
drivers/net/wireless/airo.c:7658: error: unknown field 'private' specified in initializer
drivers/net/wireless/airo.c:7658: warning: initialization makes integer from pointer without a cast
drivers/net/wireless/airo.c:7658: error: initializer element is not computable at load time
drivers/net/wireless/airo.c:7658: error: (near initialization for 'airo_handler_def.num_standard')
drivers/net/wireless/airo.c:7659: error: unknown field 'private_args' specified in initializer
drivers/net/wireless/airo.c:7659: warning: initialization from incompatible pointer type
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
nl80211: does not allow NEW_STATION and DEL_STATION for mesh
As discussed in linux-wireless mailing list, adding and removing
stations for mesh topologies is not necessary. Since doing it triggers
bugs, the sugestion was to simply disable it.
Tested using a custom iw command "station new". Works only after using
hostapd. "station del" command also works.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Simon Raffeiner <sturmflut@lieberbiber.de> Cc: Andrey Yurovsky <andrey@cozybit.com> Cc: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This manifested itself only in debug messages
and in the debugfs rename failure that would
always happen due to trying to rename the dir
over itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Tested-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 12 Feb 2010 08:05:45 +0000 (10:05 +0200)]
mac80211: fix handling of null-rate control in rate_control_get_rate
For hardware with IEEE80211_HW_HAS_RATE_CONTROL the rate controller is not
initialized. However, calling functions such as ieee80211_beacon_get result
in the rate_control_get_rate function getting called, which is accessing
(in this case uninitialized) rate control structures unconditionally.
Fix by exiting the function before setting the rates for HW with
IEEE80211_HW_HAS_RATE_CONTROL set. The initialization of the ieee80211_tx_info
struct is intentionally still executed.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Kalle Valo <kalle.valo@nokia.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Shanyu Zhao [Thu, 11 Feb 2010 18:42:22 +0000 (10:42 -0800)]
iwlwifi: fix AMSDU Rx after paged Rx patch
Previous patch "use paged Rx" broke AMSDU Rx functionality. If an AP
sends out A-MSDU packets the station will crash. Fix it by linearizing
skbuff for AMSDU packet before handing it to mac80211 since mac80211
doesn't support paged skbuff.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2155
Reported-by: Norbert Preining <preining@logic.at> Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com> Acked-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 11 Feb 2010 17:07:19 +0000 (18:07 +0100)]
ath9k: add a workaround for ack timeout issues
Adding support for setting the coverage class in some cases broke
association and data transfer, as it overwrote the initial ACK timeout
value from the initvals with a smaller value.
I don't know why the new value works in 5 GHz (matches the initval
there), but not in 2.4 GHz (initvals use 64us here), so until the
problem is fully understood, the value should be increased again.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: Monitor and recover the aggregation TX flow failure
This change monitors the tx statistics to detect the drop in throughput.
When the throughput drops, the ratio of the actual_ack_count and the expected_
ack_count also drops. At the same time, the aggregated ba_timeout (the number
of ba timeout retries) also rises. If the actual_ack_count/expected_ack_count
ratio is 0 and the number of ba timeout retries rises to 16, no tx packets
(tcp, udp, or ping - icmp) can be delivered. The driver recovers from this
situation by reseting the uCode firmware. If the actual_ack_count/expected_
ack_count ratio drops below 50% (but not 0) and the aggregated ba_timeout
retries just exceed 5 (but not 16), then the driver can reset the radio to
bring the throughput up.
Wey-Yi Guy [Tue, 9 Feb 2010 16:14:11 +0000 (08:14 -0800)]
iwlwifi: clear all the stop_queue flag after load firmware
All the queues are awake and ready to use after loading firmware,
for firmware reload case, if any queues was stopped before
reload, mac80211 will wake those queues after restart hardware, so make
sure all the flag used to keep track of the queue status are
reset correctly.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwlwifi: Adjusting PLCP error threshold for 1000 NIC
While testing the station with the NIC 1000 family, it is found that
the plcp error can easily exceed 50 value in 100mSecs. This creates
unneccessary radio reset/tuning. This patch raises the PLCP error
threshold of the NIC 1000 from 50 to 200 error count.
Reinette Chatre [Wed, 3 Feb 2010 17:38:59 +0000 (09:38 -0800)]
iwlwifi: reset card during probe
To ensure that card is in a sane state during probe we add a reset call.
This change was prompted by users of kdump who was not able to bring up the
wireless driver in the kdump kernel. The problem here was that the primary
kernel, which is not running at the time, left the wireless card up and
running. When the kdump kernel starts it is thus possible to immediately
receive interrupts from firmware after registering interrupt, but without
being ready to deal with interrupts from firmware yet.
Reinette Chatre [Tue, 2 Feb 2010 18:57:12 +0000 (10:57 -0800)]
iwlwifi: fix scan race
There is a problem if an "internal short scan" is in progress when a
mac80211 requested scan arrives. If this new scan request arrives within
the "next_scan_jiffies" period then driver will immediately return success
and complete the scan. The problem here is that the scan has not been
fully initialized at this time (is_internal_short_scan is still set to true
because of the currently running scan), which results in the scan
completion never to be sent to mac80211. At this time also, evan though the
internal short scan is still running the state (is_internal_short_scan)
will be set to false, so when the internal scan does complete then mac80211
will receive a scan completion.
Fix this by checking right away if a scan is in progress when a scan
request arrives from mac80211.
Wey-Yi Guy [Wed, 3 Feb 2010 20:24:44 +0000 (12:24 -0800)]
iwlwifi: check for aggregation frame and queue
Error checking for aggregation frames should go into aggregation queue,
if aggregation queue not available, use legacy queue instead.
Also make sure the aggregation queue is available to activate,
if driver and mac80211 is out-of-sync, try to disable the queue and
sync-up with mac80211.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Wed, 3 Feb 2010 19:47:19 +0000 (11:47 -0800)]
iwlwifi: multiple force reset mode
Provide the function to perform different type of uCode reset/reload operation.
When uCode detect error and can not fix itself, this iwl_force_reset()
function allow driver to perform the necessary reset/reload functions and help
to bring uCode back to normal operation state.
Currently only 2 type of force reset are available:
- reset radio
- reload firmware
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Sujith [Wed, 10 Feb 2010 09:22:21 +0000 (14:52 +0530)]
mac80211: Deny TX BA session requests during disassociation
In associated state, when bringing an interface down, existing
BA sessions are torn down. When this is in progress, nothing
prevents mac80211 from accepting another BA session start request.
Use a new station flag to fix this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Tue, 9 Feb 2010 18:06:54 +0000 (13:06 -0500)]
ath5k: use correct packet type when transmitting
The hardware needs to know what type of frames are being
sent in order to fill in various fields, for example the
timestamp in probe responses (before this patch, it was
always 0). Set it correctly when initializing the TX
descriptor.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vivek Natarajan [Tue, 9 Feb 2010 09:20:28 +0000 (14:50 +0530)]
mac80211: Retry null data frame for power save.
Even if the null data frame is not acked by the AP, mac80211
goes into power save. This might lead to loss of frames
from the AP.
Prevent this by restarting dynamic_ps_timer when ack is not
received for null data frames.
Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roel Kluin [Tue, 9 Feb 2010 11:07:41 +0000 (12:07 +0100)]
iwmc3200wifi: Test of wrong pointer after kzalloc in iwm_mlme_update_bss_table()
The wrong pointer was tested.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Tue, 9 Feb 2010 04:37:00 +0000 (10:07 +0530)]
ath9k: Fix sequence numbers for PAE frames
Currently, PAE frames are not assigned proper sequence numbers.
Since sending PAE frames as part of aggregates breaks
crupto with several APs, they are sent as normal MPDUs.
Fix the seqeuence number issue by updating the frame with the
internal sequence number.
Tested-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vivek Natarajan [Mon, 8 Feb 2010 12:17:01 +0000 (17:47 +0530)]
mac80211: Reset dynamic ps timer in Rx path.
The current mac80211 implementation enables power save if there
is no Tx traffic for a specific timeout. Hence, PS is triggered
even if there is a continuous Rx only traffic(like UDP) going on.
This makes the drivers to wait on the tim bit in the next beacon
to awake which leads to redundant sleep-wake cycles.
Fix this by restarting the dynamic ps timer on receiving every
data packet.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> CC: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andres Salomon [Mon, 8 Feb 2010 02:47:50 +0000 (21:47 -0500)]
mac80211: make rate_control_alloc static
rate_control_alloc is not used by anything outside of
ieee80211_init_rate_ctrl_alg. Both are in rate.c; there's no reason to make
rate_control_alloc visible outside of it.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a WARN_ON which is triggered
by Poland's country code.
ath: EEPROM regdomain: 0x8268
ath: EEPROM indicates we should expect a country code
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x37
ath: Country alpha2 being used: PL
ath: Regpair used: 0x37
-----------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/regd.c:155 ath_regd_init+0x30b
Pid: 12661, comm: firmware/carl91 2.6.33-rc5-wl #18
Call Trace:
[<>] ? warn_slowpath_common+0x76/0x8c
[<>] ? ar9170_reg_notifier+0x0/0x2d [carl9170usb]
[<>] ? ath_regd_init+0x30b/0x377 [ath]
[<>] ? ar9170_register+0x3b3/0x3ca [carl9170usb]
[...]
---[ end trace ]---
Note: Poland is just an example. But it is very likely
that more country codes are affected.
Cc: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Sun, 7 Feb 2010 08:22:01 +0000 (10:22 +0200)]
mac80211: remove get_tx_stats() driver op
get_tx_stats() driver operation is not currently used anywhere in mac80211
and there are no plans to use it in the not-so-near future. So it can go
without anyone missing it.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Sun, 7 Feb 2010 08:21:53 +0000 (10:21 +0200)]
rt2x00: remove get_tx_stats() mac80211 op
get_tx_stats() will be removed from mac80211.
Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Sun, 7 Feb 2010 08:21:46 +0000 (10:21 +0200)]
p54: remove get_tx_stats() mac80211 op
get_tx_stats() will be removed from mac80211.
p54 uses struct ieee80211_tx_queue_stats also internally, so create a new
identical struct p54_tx_queue_stats which the driver can use.
Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi> Tested-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Sun, 7 Feb 2010 08:21:37 +0000 (10:21 +0200)]
iwlwifi: remove get_tx_stats() mac80211 op
get_tx_stats() will be removed from mac80211.
Compile-tested only.
Cc: Zhu Yi <yi.zhu@intel.com> Signed-off-by: Kalle Valo <kalle.valo@iki.fi> Acked-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
git://bbs.cooldavid.org / net-next-2.6.git / log