/* Only one curve for RF5111
* find out which one and place
- * in in pd_curves.
+ * in pd_curves.
* Note: ee_x_gain is reversed here */
for (idx = 0; idx < AR5K_EEPROM_N_PD_CURVES; idx++) {
#define AR_GENTMR_BIT(_index) (1 << (_index))
/*
- * Using de Bruijin sequence to to look up 1's index in a 32 bit number
+ * Using de Bruijin sequence to look up 1's index in a 32 bit number
* debruijn32 = 0000 0111 0111 1100 1011 0101 0011 0001
*/
#define debruijn32 0x077CB531U
* LMAC. If you look at LMAC commands you'll se that they
* are actually regular iwlwifi target commands encapsulated
* into a special UMAC command called UMAC passthrough.
- * This is due to the fact the the host talks exclusively
+ * This is due to the fact the host talks exclusively
* to the UMAC and so there needs to be a special UMAC
* command for talking to the LMAC.
* This is how a wifi command is layed out:
/**
* @brief Interpret a BSS scan response returned from the firmware
*
- * Parse the various fixed fields and IEs passed back for a a BSS probe
+ * Parse the various fixed fields and IEs passed back for a BSS probe
* response or beacon from the scan command. Record information as needed
* in the scan table struct bss_descriptor for that entry.
*
} __attribute__ ((packed));
/*
- * Plug Data References are located in in the image after the last data
+ * Plug Data References are located in the image after the last data
* block. They refer to areas in the adapter memory where the plug data
* items with matching ID should be written.
*/
/*
* If the IV/EIV data was stripped from the frame before it was
* passed to the hardware, we should now reinsert it again because
- * mac80211 will expect the the same data to be present it the
+ * mac80211 will expect the same data to be present it the
* frame as it was passed to us.
*/
if (test_bit(CONFIG_SUPPORT_HW_CRYPTO, &rt2x00dev->flags))
if (skb == NULL)
return -ENOMEM;
if (need_padding) {
- /* Make sure the the payload data is 4 byte aligned. */
+ /* Make sure the payload data is 4 byte aligned. */
skb_reserve(skb, 2);
}
* @usb: a &struct zd_usb pointer
* @urb: URB to be freed
*
- * Frees the the transmission URB, which means to put it on the free URB
+ * Frees the transmission URB, which means to put it on the free URB
* list.
*/
static void free_tx_urb(struct zd_usb *usb, struct urb *urb)
* %NL80211_ATTR_REG_RULE_POWER_MAX_ANT_GAIN and
* %NL80211_ATTR_REG_RULE_POWER_MAX_EIRP.
* @NL80211_CMD_REQ_SET_REG: ask the wireless core to set the regulatory domain
- * to the the specified ISO/IEC 3166-1 alpha2 country code. The core will
+ * to the specified ISO/IEC 3166-1 alpha2 country code. The core will
* store this as a valid request and then query userspace for it.
*
* @NL80211_CMD_GET_MESH_PARAMS: Get mesh networking properties for the
* @max_power: maximum transmission power (in dBm)
* @beacon_found: helper to regulatory code to indicate when a beacon
* has been found on this channel. Use regulatory_hint_found_beacon()
- * to enable this, this is is useful only on 5 GHz band.
+ * to enable this, this is useful only on 5 GHz band.
* @orig_mag: internal use
* @orig_mpwr: internal use
*/
/*
* ieee80211_queue_work() should have picked up most cases,
- * here we'll pick the the rest.
+ * here we'll pick the rest.
*/
if (WARN(local->suspended, "STA MLME work scheduled while "
"going to suspend\n"))
/*
* This skb 'survived' a round-trip through the driver, and
* hopefully the driver didn't mangle it too badly. However,
- * we can definitely not rely on the the control information
+ * we can definitely not rely on the control information
* being correct. Clear it so we don't get junk there, and
* indicate that it needs new processing, but must not be
* modified/encrypted again.
/*
* ieee80211_queue_work() should have picked up most cases,
- * here we'll pick the the rest.
+ * here we'll pick the rest.
*/
if (WARN(local->suspended, "work scheduled while going to suspend\n"))
return;
git://bbs.cooldavid.org / net-next-2.6.git / commitdiff