#define MI_OVERLAY_OFF (0x2<<21)
#define MI_LOAD_SCAN_LINES_INCL MI_INSTR(0x12, 0)
#define MI_DISPLAY_FLIP MI_INSTR(0x14, 2)
+#define MI_DISPLAY_FLIP_I915 MI_INSTR(0x14, 1)
#define MI_DISPLAY_FLIP_PLANE(n) ((n) << 20)
#define MI_STORE_DWORD_IMM MI_INSTR(0x20, 1)
#define MI_MEM_VIRTUAL (1 << 22) /* 965+ only */
#define I915_DEBUG_INTERRUPT (1<<2)
#define I915_USER_INTERRUPT (1<<1)
#define I915_ASLE_INTERRUPT (1<<0)
+#define I915_BSD_USER_INTERRUPT (1<<25)
#define EIR 0x020b0
#define EMR 0x020b4
#define ESR 0x020b8
#define LM_BURST_LENGTH 0x00000700
#define LM_FIFO_WATERMARK 0x0000001F
#define MI_ARB_STATE 0x020e4 /* 915+ only */
+#define MI_ARB_MASK_SHIFT 16 /* shift for enable bits */
+
+/* Make render/texture TLB fetches lower priorty than associated data
+ * fetches. This is not turned on by default
+ */
+#define MI_ARB_RENDER_TLB_LOW_PRIORITY (1 << 15)
+
+/* Isoch request wait on GTT enable (Display A/B/C streams).
+ * Make isoch requests stall on the TLB update. May cause
+ * display underruns (test mode only)
+ */
+#define MI_ARB_ISOCH_WAIT_GTT (1 << 14)
+
+/* Block grant count for isoch requests when block count is
+ * set to a finite value.
+ */
+#define MI_ARB_BLOCK_GRANT_MASK (3 << 12)
+#define MI_ARB_BLOCK_GRANT_8 (0 << 12) /* for 3 display planes */
+#define MI_ARB_BLOCK_GRANT_4 (1 << 12) /* for 2 display planes */
+#define MI_ARB_BLOCK_GRANT_2 (2 << 12) /* for 1 display plane */
+#define MI_ARB_BLOCK_GRANT_0 (3 << 12) /* don't use */
+
+/* Enable render writes to complete in C2/C3/C4 power states.
+ * If this isn't enabled, render writes are prevented in low
+ * power states. That seems bad to me.
+ */
+#define MI_ARB_C3_LP_WRITE_ENABLE (1 << 11)
+
+/* This acknowledges an async flip immediately instead
+ * of waiting for 2TLB fetches.
+ */
+#define MI_ARB_ASYNC_FLIP_ACK_IMMEDIATE (1 << 10)
+
+/* Enables non-sequential data reads through arbiter
+ */
+#define MI_ARB_DUAL_DATA_PHASE_DISABLE (1 << 9)
+
+/* Disable FSB snooping of cacheable write cycles from binner/render
+ * command stream
+ */
+#define MI_ARB_CACHE_SNOOP_DISABLE (1 << 8)
+
+/* Arbiter time slice for non-isoch streams */
+#define MI_ARB_TIME_SLICE_MASK (7 << 5)
+#define MI_ARB_TIME_SLICE_1 (0 << 5)
+#define MI_ARB_TIME_SLICE_2 (1 << 5)
+#define MI_ARB_TIME_SLICE_4 (2 << 5)
+#define MI_ARB_TIME_SLICE_6 (3 << 5)
+#define MI_ARB_TIME_SLICE_8 (4 << 5)
+#define MI_ARB_TIME_SLICE_10 (5 << 5)
+#define MI_ARB_TIME_SLICE_14 (6 << 5)
+#define MI_ARB_TIME_SLICE_16 (7 << 5)
+
+/* Low priority grace period page size */
+#define MI_ARB_LOW_PRIORITY_GRACE_4KB (0 << 4) /* default */
+#define MI_ARB_LOW_PRIORITY_GRACE_8KB (1 << 4)
+
+/* Disable display A/B trickle feed */
+#define MI_ARB_DISPLAY_TRICKLE_FEED_DISABLE (1 << 2)
+
+/* Set display plane priority */
+#define MI_ARB_DISPLAY_PRIORITY_A_B (0 << 0) /* display A > display B */
+#define MI_ARB_DISPLAY_PRIORITY_B_A (1 << 0) /* display B > display A */
+
#define CACHE_MODE_0 0x02120 /* 915+ only */
#define CM0_MASK_SHIFT 16
#define CM0_IZ_OPT_DISABLE (1<<6)
#define CM0_RC_OP_FLUSH_DISABLE (1<<0)
#define BB_ADDR 0x02140 /* 8 bytes */
#define GFX_FLSH_CNTL 0x02170 /* 915+ only */
+#define ECOSKPD 0x021d0
+#define ECO_GATING_CX_ONLY (1<<3)
+#define ECO_FLIP_DONE (1<<0)
+
+/* GEN6 interrupt control */
+#define GEN6_RENDER_HWSTAM 0x2098
+#define GEN6_RENDER_IMR 0x20a8
+#define GEN6_RENDER_CONTEXT_SWITCH_INTERRUPT (1 << 8)
+#define GEN6_RENDER_PPGTT_PAGE_FAULT (1 << 7)
+#define GEN6_RENDER TIMEOUT_COUNTER_EXPIRED (1 << 6)
+#define GEN6_RENDER_L3_PARITY_ERROR (1 << 5)
+#define GEN6_RENDER_PIPE_CONTROL_NOTIFY_INTERRUPT (1 << 4)
+#define GEN6_RENDER_COMMAND_PARSER_MASTER_ERROR (1 << 3)
+#define GEN6_RENDER_SYNC_STATUS (1 << 2)
+#define GEN6_RENDER_DEBUG_INTERRUPT (1 << 1)
+#define GEN6_RENDER_USER_INTERRUPT (1 << 0)
+
+#define GEN6_BLITTER_HWSTAM 0x22098
+#define GEN6_BLITTER_IMR 0x220a8
+#define GEN6_BLITTER_MI_FLUSH_DW_NOTIFY_INTERRUPT (1 << 26)
+#define GEN6_BLITTER_COMMAND_PARSER_MASTER_ERROR (1 << 25)
+#define GEN6_BLITTER_SYNC_STATUS (1 << 24)
+#define GEN6_BLITTER_USER_INTERRUPT (1 << 22)
+/*
+ * BSD (bit stream decoder instruction and interrupt control register defines
+ * (G4X and Ironlake only)
+ */
+#define BSD_RING_TAIL 0x04030
+#define BSD_RING_HEAD 0x04034
+#define BSD_RING_START 0x04038
+#define BSD_RING_CTL 0x0403c
+#define BSD_RING_ACTHD 0x04074
+#define BSD_HWS_PGA 0x04080
/*
* Framebuffer compression (915+ only)
#define DCC_CHANNEL_XOR_DISABLE (1 << 10)
#define DCC_CHANNEL_XOR_BIT_17 (1 << 9)
+/** Pineview MCH register contains DDR3 setting */
+#define CSHRDDR3CTL 0x101a8
+#define CSHRDDR3CTL_DDR3 (1 << 2)
+
/** 965 MCH register controlling DRAM channel configuration */
#define C0DRB3 0x10206
#define C1DRB3 0x10606
#define CLKCFG_MEM_800 (3 << 4)
#define CLKCFG_MEM_MASK (7 << 4)
+#define TR1 0x11006
+#define TSFS 0x11020
+#define TSFS_SLOPE_MASK 0x0000ff00
+#define TSFS_SLOPE_SHIFT 8
+#define TSFS_INTR_MASK 0x000000ff
+
#define CRSTANDVID 0x11100
#define PXVFREQ_BASE 0x11110 /* P[0-15]VIDFREQ (0x1114c) (Ironlake) */
#define PXVFREQ_PX_MASK 0x7f000000
#define MEMSTAT_SRC_CTL_STDBY 3
#define RCPREVBSYTUPAVG 0x113b8
#define RCPREVBSYTDNAVG 0x113bc
+#define SDEW 0x1124c
+#define CSIEW0 0x11250
+#define CSIEW1 0x11254
+#define CSIEW2 0x11258
+#define PEW 0x1125c
+#define DEW 0x11270
+#define MCHAFE 0x112c0
+#define CSIEC 0x112e0
+#define DMIEC 0x112e4
+#define DDREC 0x112e8
+#define PEG0EC 0x112ec
+#define PEG1EC 0x112f0
+#define GFXEC 0x112f4
+#define RPPREVBSYTUPAVG 0x113b8
+#define RPPREVBSYTDNAVG 0x113bc
+#define ECR 0x11600
+#define ECR_GPFE (1<<31)
+#define ECR_IMONE (1<<30)
+#define ECR_CAP_MASK 0x0000001f /* Event range, 0-31 */
+#define OGW0 0x11608
+#define OGW1 0x1160c
+#define EG0 0x11610
+#define EG1 0x11614
+#define EG2 0x11618
+#define EG3 0x1161c
+#define EG4 0x11620
+#define EG5 0x11624
+#define EG6 0x11628
+#define EG7 0x1162c
+#define PXW 0x11664
+#define PXWL 0x11680
+#define LCFUSE02 0x116c0
+#define LCFUSE_HIV_MASK 0x000000ff
+#define CSIPLL0 0x12c10
+#define DDRMPLL1 0X12c20
#define PEG_BAND_GAP_DATA 0x14d68
/*
#define CRT_HOTPLUG_DETECT_DELAY_2G (1 << 4)
#define CRT_HOTPLUG_DETECT_VOLTAGE_325MV (0 << 2)
#define CRT_HOTPLUG_DETECT_VOLTAGE_475MV (1 << 2)
-#define CRT_HOTPLUG_MASK (0x3fc) /* Bits 9-2 */
-#define CRT_FORCE_HOTPLUG_MASK 0xfffffe1f
#define PORT_HOTPLUG_STAT 0x61114
#define HDMIB_HOTPLUG_INT_STATUS (1 << 29)
#define GT_PIPE_NOTIFY (1 << 4)
#define GT_SYNC_STATUS (1 << 2)
#define GT_USER_INTERRUPT (1 << 0)
+#define GT_BSD_USER_INTERRUPT (1 << 5)
+
#define GTISR 0x44010
#define GTIMR 0x44014
#define SDVO_ENCODING (0)
#define TMDS_ENCODING (2 << 10)
#define NULL_PACKET_VSYNC_ENABLE (1 << 9)
+/* CPT */
+#define HDMI_MODE_SELECT (1 << 9)
+#define DVI_MODE_SELECT (0)
#define SDVOB_BORDER_ENABLE (1 << 7)
#define AUDIO_ENABLE (1 << 6)
#define VSYNC_ACTIVE_HIGH (1 << 4)
git://bbs.cooldavid.org / net-next-2.6.git / blobdiff