#define MI_NO_WRITE_FLUSH (1 << 2)
#define MI_SCENE_COUNT (1 << 3) /* just increment scene count */
#define MI_END_SCENE (1 << 4) /* flush binner and incr scene count */
+#define MI_INVALIDATE_ISP (1 << 5) /* invalidate indirect state pointers */
#define MI_BATCH_BUFFER_END MI_INSTR(0x0a, 0)
#define MI_REPORT_HEAD MI_INSTR(0x07, 0)
#define MI_OVERLAY_FLIP MI_INSTR(0x11,0)
#define MI_DISPLAY_FLIP MI_INSTR(0x14, 2)
#define MI_DISPLAY_FLIP_I915 MI_INSTR(0x14, 1)
#define MI_DISPLAY_FLIP_PLANE(n) ((n) << 20)
+#define MI_SET_CONTEXT MI_INSTR(0x18, 0)
+#define MI_MM_SPACE_GTT (1<<8)
+#define MI_MM_SPACE_PHYSICAL (0<<8)
+#define MI_SAVE_EXT_STATE_EN (1<<3)
+#define MI_RESTORE_EXT_STATE_EN (1<<2)
+#define MI_RESTORE_INHIBIT (1<<0)
#define MI_STORE_DWORD_IMM MI_INSTR(0x20, 1)
#define MI_MEM_VIRTUAL (1 << 22) /* 965+ only */
#define MI_STORE_DWORD_INDEX MI_INSTR(0x21, 1)
#define LM_BURST_LENGTH 0x00000700
#define LM_FIFO_WATERMARK 0x0000001F
#define MI_ARB_STATE 0x020e4 /* 915+ only */
+#define MI_ARB_MASK_SHIFT 16 /* shift for enable bits */
+
+/* Make render/texture TLB fetches lower priorty than associated data
+ * fetches. This is not turned on by default
+ */
+#define MI_ARB_RENDER_TLB_LOW_PRIORITY (1 << 15)
+
+/* Isoch request wait on GTT enable (Display A/B/C streams).
+ * Make isoch requests stall on the TLB update. May cause
+ * display underruns (test mode only)
+ */
+#define MI_ARB_ISOCH_WAIT_GTT (1 << 14)
+
+/* Block grant count for isoch requests when block count is
+ * set to a finite value.
+ */
+#define MI_ARB_BLOCK_GRANT_MASK (3 << 12)
+#define MI_ARB_BLOCK_GRANT_8 (0 << 12) /* for 3 display planes */
+#define MI_ARB_BLOCK_GRANT_4 (1 << 12) /* for 2 display planes */
+#define MI_ARB_BLOCK_GRANT_2 (2 << 12) /* for 1 display plane */
+#define MI_ARB_BLOCK_GRANT_0 (3 << 12) /* don't use */
+
+/* Enable render writes to complete in C2/C3/C4 power states.
+ * If this isn't enabled, render writes are prevented in low
+ * power states. That seems bad to me.
+ */
+#define MI_ARB_C3_LP_WRITE_ENABLE (1 << 11)
+
+/* This acknowledges an async flip immediately instead
+ * of waiting for 2TLB fetches.
+ */
+#define MI_ARB_ASYNC_FLIP_ACK_IMMEDIATE (1 << 10)
+
+/* Enables non-sequential data reads through arbiter
+ */
+#define MI_ARB_DUAL_DATA_PHASE_DISABLE (1 << 9)
+
+/* Disable FSB snooping of cacheable write cycles from binner/render
+ * command stream
+ */
+#define MI_ARB_CACHE_SNOOP_DISABLE (1 << 8)
+
+/* Arbiter time slice for non-isoch streams */
+#define MI_ARB_TIME_SLICE_MASK (7 << 5)
+#define MI_ARB_TIME_SLICE_1 (0 << 5)
+#define MI_ARB_TIME_SLICE_2 (1 << 5)
+#define MI_ARB_TIME_SLICE_4 (2 << 5)
+#define MI_ARB_TIME_SLICE_6 (3 << 5)
+#define MI_ARB_TIME_SLICE_8 (4 << 5)
+#define MI_ARB_TIME_SLICE_10 (5 << 5)
+#define MI_ARB_TIME_SLICE_14 (6 << 5)
+#define MI_ARB_TIME_SLICE_16 (7 << 5)
+
+/* Low priority grace period page size */
+#define MI_ARB_LOW_PRIORITY_GRACE_4KB (0 << 4) /* default */
+#define MI_ARB_LOW_PRIORITY_GRACE_8KB (1 << 4)
+
+/* Disable display A/B trickle feed */
+#define MI_ARB_DISPLAY_TRICKLE_FEED_DISABLE (1 << 2)
+
+/* Set display plane priority */
+#define MI_ARB_DISPLAY_PRIORITY_A_B (0 << 0) /* display A > display B */
+#define MI_ARB_DISPLAY_PRIORITY_B_A (1 << 0) /* display B > display A */
+
#define CACHE_MODE_0 0x02120 /* 915+ only */
#define CM0_MASK_SHIFT 16
#define CM0_IZ_OPT_DISABLE (1<<6)
#define GEN6_RENDER_IMR 0x20a8
#define GEN6_RENDER_CONTEXT_SWITCH_INTERRUPT (1 << 8)
#define GEN6_RENDER_PPGTT_PAGE_FAULT (1 << 7)
-#define GEN6_RENDER TIMEOUT_COUNTER_EXPIRED (1 << 6)
+#define GEN6_RENDER_TIMEOUT_COUNTER_EXPIRED (1 << 6)
#define GEN6_RENDER_L3_PARITY_ERROR (1 << 5)
#define GEN6_RENDER_PIPE_CONTROL_NOTIFY_INTERRUPT (1 << 4)
#define GEN6_RENDER_COMMAND_PARSER_MASTER_ERROR (1 << 3)
#define DPFC_CHICKEN 0x3224
#define DPFC_HT_MODIFY (1<<31)
+/* Framebuffer compression for Ironlake */
+#define ILK_DPFC_CB_BASE 0x43200
+#define ILK_DPFC_CONTROL 0x43208
+/* The bit 28-8 is reserved */
+#define DPFC_RESERVED (0x1FFFFF00)
+#define ILK_DPFC_RECOMP_CTL 0x4320c
+#define ILK_DPFC_STATUS 0x43210
+#define ILK_DPFC_FENCE_YOFF 0x43218
+#define ILK_DPFC_CHICKEN 0x43224
+#define ILK_FBC_RT_BASE 0x2128
+#define ILK_FBC_RT_VALID (1<<0)
+
+#define ILK_DISPLAY_CHICKEN1 0x42000
+#define ILK_FBCQ_DIS (1<<22)
+
/*
* GPIO regs
*/
#define DPLL_FPA01_P1_POST_DIV_MASK 0x00ff0000 /* i915 */
#define DPLL_FPA01_P1_POST_DIV_MASK_PINEVIEW 0x00ff8000 /* Pineview */
-#define I915_FIFO_UNDERRUN_STATUS (1UL<<31)
-#define I915_CRC_ERROR_ENABLE (1UL<<29)
-#define I915_CRC_DONE_ENABLE (1UL<<28)
-#define I915_GMBUS_EVENT_ENABLE (1UL<<27)
-#define I915_VSYNC_INTERRUPT_ENABLE (1UL<<25)
-#define I915_DISPLAY_LINE_COMPARE_ENABLE (1UL<<24)
-#define I915_DPST_EVENT_ENABLE (1UL<<23)
-#define I915_LEGACY_BLC_EVENT_ENABLE (1UL<<22)
-#define I915_ODD_FIELD_INTERRUPT_ENABLE (1UL<<21)
-#define I915_EVEN_FIELD_INTERRUPT_ENABLE (1UL<<20)
-#define I915_START_VBLANK_INTERRUPT_ENABLE (1UL<<18) /* 965 or later */
-#define I915_VBLANK_INTERRUPT_ENABLE (1UL<<17)
-#define I915_OVERLAY_UPDATED_ENABLE (1UL<<16)
-#define I915_CRC_ERROR_INTERRUPT_STATUS (1UL<<13)
-#define I915_CRC_DONE_INTERRUPT_STATUS (1UL<<12)
-#define I915_GMBUS_INTERRUPT_STATUS (1UL<<11)
-#define I915_VSYNC_INTERRUPT_STATUS (1UL<<9)
-#define I915_DISPLAY_LINE_COMPARE_STATUS (1UL<<8)
-#define I915_DPST_EVENT_STATUS (1UL<<7)
-#define I915_LEGACY_BLC_EVENT_STATUS (1UL<<6)
-#define I915_ODD_FIELD_INTERRUPT_STATUS (1UL<<5)
-#define I915_EVEN_FIELD_INTERRUPT_STATUS (1UL<<4)
-#define I915_START_VBLANK_INTERRUPT_STATUS (1UL<<2) /* 965 or later */
-#define I915_VBLANK_INTERRUPT_STATUS (1UL<<1)
-#define I915_OVERLAY_UPDATED_STATUS (1UL<<0)
-
#define SRX_INDEX 0x3c4
#define SRX_DATA 0x3c5
#define SR01 1
#define DDRMPLL1 0X12c20
#define PEG_BAND_GAP_DATA 0x14d68
+/*
+ * Logical Context regs
+ */
+#define CCID 0x2180
+#define CCID_EN (1<<0)
/*
* Overlay regs
*/
#define PIPE_DITHER_TYPE_ST01 (1 << 2)
/* Pipe A */
#define PIPEADSL 0x70000
+#define DSL_LINEMASK 0x00000fff
#define PIPEACONF 0x70008
#define PIPEACONF_ENABLE (1<<31)
#define PIPEACONF_DISABLE 0
#define I830_FIFO_LINE_SIZE 32
#define G4X_FIFO_SIZE 127
-#define I945_FIFO_SIZE 127 /* 945 & 965 */
+#define I965_FIFO_SIZE 512
+#define I945_FIFO_SIZE 127
#define I915_FIFO_SIZE 95
#define I855GM_FIFO_SIZE 127 /* In cachelines */
#define I830_FIFO_SIZE 95
#define PINEVIEW_CURSOR_DFT_WM 0
#define PINEVIEW_CURSOR_GUARD_WM 5
+#define I965_CURSOR_FIFO 64
+#define I965_CURSOR_MAX_WM 32
+#define I965_CURSOR_DFT_WM 8
/* define the Watermark register on Ironlake */
#define WM0_PIPEA_ILK 0x45100
#define ILK_DISPLAY_FIFO 128
#define ILK_DISPLAY_MAXWM 64
#define ILK_DISPLAY_DFTWM 8
+#define ILK_CURSOR_FIFO 32
+#define ILK_CURSOR_MAXWM 16
+#define ILK_CURSOR_DFTWM 8
#define ILK_DISPLAY_SR_FIFO 512
#define ILK_DISPLAY_MAX_SRWM 0x1ff
#define ILK_VSDPFD_FULL (1<<21)
#define ILK_DSPCLK_GATE 0x42020
#define ILK_DPARB_CLK_GATE (1<<5)
+/* According to spec this bit 7/8/9 of 0x42020 should be set to enable FBC */
+#define ILK_CLK_FBC (1<<7)
+#define ILK_DPFC_DIS1 (1<<8)
+#define ILK_DPFC_DIS2 (1<<9)
#define DISP_ARB_CTL 0x45000
#define DISP_TILE_SURFACE_SWIZZLING (1<<13)
#define PCH_PP_STATUS 0xc7200
#define PCH_PP_CONTROL 0xc7204
+#define PANEL_UNLOCK_REGS (0xabcd << 16)
#define EDP_FORCE_VDD (1 << 3)
#define EDP_BLC_ENABLE (1 << 2)
#define PANEL_POWER_RESET (1 << 1)
#define TRANS_DP_VSYNC_ACTIVE_LOW 0
#define TRANS_DP_HSYNC_ACTIVE_HIGH (1<<3)
#define TRANS_DP_HSYNC_ACTIVE_LOW 0
+#define TRANS_DP_SYNC_MASK (3<<3)
/* SNB eDP training params */
/* SNB A-stepping */