driver core: basic infrastructure for per-module dynamic debug messages

[net-next-2.6.git] / Documentation / kernel-parameters.txt

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index a2701cb6b37a961a0267819a09f5759a49901c32..b429c84ceef206124fbb959e17754981ca6e7964 100644 (file)
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -658,11 +658,12 @@ and is between 256 and 4096 characters. It is defined in the file
        earlyprintk=    [X86-32,X86-64,SH,BLACKFIN]
                        earlyprintk=vga
                        earlyprintk=serial[,ttySn[,baudrate]]
+                       earlyprintk=dbgp
 
                        Append ",keep" to not disable it when the real console
                        takes over.
 
-                       Only vga or serial at a time, not both.
+                       Only vga or serial or usb debug port at a time.
 
                        Currently only ttyS0 and ttyS1 are supported.
 
@@ -1019,6 +1020,10 @@ and is between 256 and 4096 characters. It is defined in the file
                        (only serial suported for now)
                        Format: <serial_device>[,baud]
 
+       kmac=           [MIPS] korina ethernet MAC address.
+                       Configure the RouterBoard 532 series on-chip
+                       Ethernet adapter MAC address.
+
        l2cr=           [PPC]
 
        l3cr=           [PPC]
@@ -1227,6 +1232,29 @@ and is between 256 and 4096 characters. It is defined in the file
                                 or
                                 memmap=0x10000$0x18690000
 
+       memory_corruption_check=0/1 [X86]
+                       Some BIOSes seem to corrupt the first 64k of
+                       memory when doing things like suspend/resume.
+                       Setting this option will scan the memory
+                       looking for corruption.  Enabling this will
+                       both detect corruption and prevent the kernel
+                       from using the memory being corrupted.
+                       However, its intended as a diagnostic tool; if
+                       repeatable BIOS-originated corruption always
+                       affects the same memory, you can use memmap=
+                       to prevent the kernel from using that memory.
+
+       memory_corruption_check_size=size [X86]
+                       By default it checks for corruption in the low
+                       64k, making this memory unavailable for normal
+                       use.  Use this parameter to scan for
+                       corruption in more or less memory.
+
+       memory_corruption_check_period=seconds [X86]
+                       By default it checks for corruption every 60
+                       seconds.  Use this parameter to check at some
+                       other rate.  0 disables periodic checking.
+
        memtest=        [KNL,X86] Enable memtest
                        Format: <integer>
                        range: 0,4 : pattern number
@@ -1424,6 +1452,12 @@ and is between 256 and 4096 characters. It is defined in the file
 
        nolapic_timer   [X86-32,APIC] Do not use the local APIC timer.
 
+       nox2apic        [X86-64,APIC] Do not enable x2APIC mode.
+
+       x2apic_phys     [X86-64,APIC] Use x2apic physical mode instead of
+                       default x2apic cluster mode on platforms
+                       supporting x2apic.
+
        noltlbs         [PPC] Do not use large page/tlb entries for kernel
                        lowmem mapping on PPC40x.
 
@@ -1679,6 +1713,11 @@ and is between 256 and 4096 characters. It is defined in the file
                        autoconfiguration.
                        Ranges are in pairs (memory base and size).
 
+       dynamic_printk
+                       Enables pr_debug()/dev_dbg() calls if
+                       CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled. These can also
+                       be switched on/off via <debugfs>/dynamic_printk/modules
+
        print-fatal-signals=
                        [KNL] debug: print fatal signals
                        print-fatal-signals=1: print segfault info to