[net-next-2.6.git] / include / linux / mmc / sdio.h

/*
 *  include/linux/mmc/sdio.h
 *
 *  Copyright 2006-2007 Pierre Ossman
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or (at
 * your option) any later version.
 */

#ifndef MMC_SDIO_H
#define MMC_SDIO_H

/* SDIO commands                         type  argument     response */
#define SD_IO_SEND_OP_COND          5 /* bcr  [23:0] OCR         R4  */
#define SD_IO_RW_DIRECT            52 /* ac   [31:0] See below   R5  */
#define SD_IO_RW_EXTENDED          53 /* adtc [31:0] See below   R5  */

/*
 * SD_IO_RW_DIRECT argument format:
 *
 *      [31] R/W flag
 *      [30:28] Function number
 *      [27] RAW flag
 *      [25:9] Register address
 *      [7:0] Data
 */

/*
 * SD_IO_RW_EXTENDED argument format:
 *
 *      [31] R/W flag
 *      [30:28] Function number
 *      [27] Block mode
 *      [26] Increment address
 *      [25:9] Register address
 *      [8:0] Byte/block count
 */

#define R4_MEMORY_PRESENT (1 << 27)

/*
  SDIO status in R5
  Type
	e : error bit
	s : status bit
	r : detected and set for the actual command response
	x : detected and set during command execution. the host must poll
            the card by sending status command in order to read these bits.
  Clear condition
	a : according to the card state
	b : always related to the previous command. Reception of
            a valid command will clear it (with a delay of one command)
	c : clear by read
 */

#define R5_COM_CRC_ERROR	(1 << 15)	/* er, b */
#define R5_ILLEGAL_COMMAND	(1 << 14)	/* er, b */
#define R5_ERROR		(1 << 11)	/* erx, c */
#define R5_FUNCTION_NUMBER	(1 << 9)	/* er, c */
#define R5_OUT_OF_RANGE		(1 << 8)	/* er, c */
#define R5_STATUS(x)		(x & 0xCB00)
#define R5_IO_CURRENT_STATE(x)	((x & 0x3000) >> 12) /* s, b */

/*
 * Card Common Control Registers (CCCR)
 */

#define SDIO_CCCR_CCCR		0x00

#define  SDIO_CCCR_REV_1_00	0	/* CCCR/FBR Version 1.00 */
#define  SDIO_CCCR_REV_1_10	1	/* CCCR/FBR Version 1.10 */
#define  SDIO_CCCR_REV_1_20	2	/* CCCR/FBR Version 1.20 */

#define  SDIO_SDIO_REV_1_00	0	/* SDIO Spec Version 1.00 */
#define  SDIO_SDIO_REV_1_10	1	/* SDIO Spec Version 1.10 */
#define  SDIO_SDIO_REV_1_20	2	/* SDIO Spec Version 1.20 */
#define  SDIO_SDIO_REV_2_00	3	/* SDIO Spec Version 2.00 */

#define SDIO_CCCR_SD		0x01

#define  SDIO_SD_REV_1_01	0	/* SD Physical Spec Version 1.01 */
#define  SDIO_SD_REV_1_10	1	/* SD Physical Spec Version 1.10 */
#define  SDIO_SD_REV_2_00	2	/* SD Physical Spec Version 2.00 */

#define SDIO_CCCR_IOEx		0x02
#define SDIO_CCCR_IORx		0x03

#define SDIO_CCCR_IENx		0x04	/* Function/Master Interrupt Enable */
#define SDIO_CCCR_INTx		0x05	/* Function Interrupt Pending */

#define SDIO_CCCR_ABORT		0x06	/* function abort/card reset */

#define SDIO_CCCR_IF		0x07	/* bus interface controls */

#define  SDIO_BUS_WIDTH_1BIT	0x00
#define  SDIO_BUS_WIDTH_4BIT	0x02
#define  SDIO_BUS_ECSI		0x20	/* Enable continuous SPI interrupt */
#define  SDIO_BUS_SCSI		0x40	/* Support continuous SPI interrupt */

#define  SDIO_BUS_ASYNC_INT	0x20

#define  SDIO_BUS_CD_DISABLE     0x80	/* disable pull-up on DAT3 (pin 1) */

#define SDIO_CCCR_CAPS		0x08

#define  SDIO_CCCR_CAP_SDC	0x01	/* can do CMD52 while data transfer */
#define  SDIO_CCCR_CAP_SMB	0x02	/* can do multi-block xfers (CMD53) */
#define  SDIO_CCCR_CAP_SRW	0x04	/* supports read-wait protocol */
#define  SDIO_CCCR_CAP_SBS	0x08	/* supports suspend/resume */
#define  SDIO_CCCR_CAP_S4MI	0x10	/* interrupt during 4-bit CMD53 */
#define  SDIO_CCCR_CAP_E4MI	0x20	/* enable ints during 4-bit CMD53 */
#define  SDIO_CCCR_CAP_LSC	0x40	/* low speed card */
#define  SDIO_CCCR_CAP_4BLS	0x80	/* 4 bit low speed card */

#define SDIO_CCCR_CIS		0x09	/* common CIS pointer (3 bytes) */

/* Following 4 regs are valid only if SBS is set */
#define SDIO_CCCR_SUSPEND	0x0c
#define SDIO_CCCR_SELx		0x0d
#define SDIO_CCCR_EXECx		0x0e
#define SDIO_CCCR_READYx	0x0f

#define SDIO_CCCR_BLKSIZE	0x10

#define SDIO_CCCR_POWER		0x12

#define  SDIO_POWER_SMPC	0x01	/* Supports Master Power Control */
#define  SDIO_POWER_EMPC	0x02	/* Enable Master Power Control */

#define SDIO_CCCR_SPEED		0x13

#define  SDIO_SPEED_SHS		0x01	/* Supports High-Speed mode */
#define  SDIO_SPEED_EHS		0x02	/* Enable High-Speed mode */

/*
 * Function Basic Registers (FBR)
 */

#define SDIO_FBR_BASE(f)	((f) * 0x100) /* base of function f's FBRs */

#define SDIO_FBR_STD_IF		0x00

#define  SDIO_FBR_SUPPORTS_CSA	0x40	/* supports Code Storage Area */
#define  SDIO_FBR_ENABLE_CSA	0x80	/* enable Code Storage Area */

#define SDIO_FBR_STD_IF_EXT	0x01

#define SDIO_FBR_POWER		0x02

#define  SDIO_FBR_POWER_SPS	0x01	/* Supports Power Selection */
#define  SDIO_FBR_POWER_EPS	0x02	/* Enable (low) Power Selection */

#define SDIO_FBR_CIS		0x09	/* CIS pointer (3 bytes) */


#define SDIO_FBR_CSA		0x0C	/* CSA pointer (3 bytes) */

#define SDIO_FBR_CSA_DATA	0x0F

#define SDIO_FBR_BLKSIZE	0x10	/* block size (2 bytes) */

#endif
Commit	Line	Data
5c4e6f13 PO	1	/*
	2	* include/linux/mmc/sdio.h
	3	*
	4	* Copyright 2006-2007 Pierre Ossman
	5	*
	6	* This program is free software; you can redistribute it and/or modify
	7	* it under the terms of the GNU General Public License as published by
	8	* the Free Software Foundation; either version 2 of the License, or (at
	9	* your option) any later version.
	10	*/
	11
	12	#ifndef MMC_SDIO_H
	13	#define MMC_SDIO_H
	14
	15	/* SDIO commands type argument response */
	16	#define SD_IO_SEND_OP_COND 5 /* bcr [23:0] OCR R4 */
b2bcc798	17	#define SD_IO_RW_DIRECT 52 /* ac [31:0] See below R5 */
112c9db9	18	#define SD_IO_RW_EXTENDED 53 /* adtc [31:0] See below R5 */
b2bcc798 PO	19
	20	/*
	21	* SD_IO_RW_DIRECT argument format:
	22	*
	23	* [31] R/W flag
	24	* [30:28] Function number
	25	* [27] RAW flag
	26	* [25:9] Register address
	27	* [7:0] Data
	28	*/
	29
112c9db9 PO	30	/*
	31	* SD_IO_RW_EXTENDED argument format:
	32	*
	33	* [31] R/W flag
	34	* [30:28] Function number
	35	* [27] Block mode
	36	* [26] Increment address
	37	* [25:9] Register address
	38	* [8:0] Byte/block count
	39	*/
	40
f3c65b28 DV	41	#define R4_MEMORY_PRESENT (1 << 27)
f3c65b28 DV	42
b2bcc798 PO	43	/*
	44	SDIO status in R5
	45	Type
	46	e : error bit
	47	s : status bit
	48	r : detected and set for the actual command response
	49	x : detected and set during command execution. the host must poll
	50	the card by sending status command in order to read these bits.
	51	Clear condition
	52	a : according to the card state
	53	b : always related to the previous command. Reception of
	54	a valid command will clear it (with a delay of one command)
	55	c : clear by read
	56	*/
	57
	58	#define R5_COM_CRC_ERROR (1 << 15) /* er, b */
	59	#define R5_ILLEGAL_COMMAND (1 << 14) /* er, b */
	60	#define R5_ERROR (1 << 11) /* erx, c */
	61	#define R5_FUNCTION_NUMBER (1 << 9) /* er, c */
	62	#define R5_OUT_OF_RANGE (1 << 8) /* er, c */
	63	#define R5_STATUS(x) (x & 0xCB00)
	64	#define R5_IO_CURRENT_STATE(x) ((x & 0x3000) >> 12) /* s, b */
5c4e6f13	65
fa64efa1 PO	66	/*
	67	* Card Common Control Registers (CCCR)
	68	*/
	69
	70	#define SDIO_CCCR_CCCR 0x00
	71
	72	#define SDIO_CCCR_REV_1_00 0 /* CCCR/FBR Version 1.00 */
	73	#define SDIO_CCCR_REV_1_10 1 /* CCCR/FBR Version 1.10 */
	74	#define SDIO_CCCR_REV_1_20 2 /* CCCR/FBR Version 1.20 */
	75
	76	#define SDIO_SDIO_REV_1_00 0 /* SDIO Spec Version 1.00 */
	77	#define SDIO_SDIO_REV_1_10 1 /* SDIO Spec Version 1.10 */
	78	#define SDIO_SDIO_REV_1_20 2 /* SDIO Spec Version 1.20 */
	79	#define SDIO_SDIO_REV_2_00 3 /* SDIO Spec Version 2.00 */
	80
	81	#define SDIO_CCCR_SD 0x01
	82
	83	#define SDIO_SD_REV_1_01 0 /* SD Physical Spec Version 1.01 */
	84	#define SDIO_SD_REV_1_10 1 /* SD Physical Spec Version 1.10 */
	85	#define SDIO_SD_REV_2_00 2 /* SD Physical Spec Version 2.00 */
	86
	87	#define SDIO_CCCR_IOEx 0x02
	88	#define SDIO_CCCR_IORx 0x03
	89
	90	#define SDIO_CCCR_IENx 0x04 /* Function/Master Interrupt Enable */
	91	#define SDIO_CCCR_INTx 0x05 /* Function Interrupt Pending */
	92
	93	#define SDIO_CCCR_ABORT 0x06 /* function abort/card reset */
	94
	95	#define SDIO_CCCR_IF 0x07 /* bus interface controls */
	96
	97	#define SDIO_BUS_WIDTH_1BIT 0x00
	98	#define SDIO_BUS_WIDTH_4BIT 0x02
8a64c0f6 DM	99	#define SDIO_BUS_ECSI 0x20 /* Enable continuous SPI interrupt */
8a64c0f6 DM	100	#define SDIO_BUS_SCSI 0x40 /* Support continuous SPI interrupt */
fa64efa1	101
6b5eda36 DD	102	#define SDIO_BUS_ASYNC_INT 0x20
6b5eda36 DD	103
fa64efa1 PO	104	#define SDIO_BUS_CD_DISABLE 0x80 /* disable pull-up on DAT3 (pin 1) */
	105
	106	#define SDIO_CCCR_CAPS 0x08
	107
	108	#define SDIO_CCCR_CAP_SDC 0x01 /* can do CMD52 while data transfer */
	109	#define SDIO_CCCR_CAP_SMB 0x02 /* can do multi-block xfers (CMD53) */
	110	#define SDIO_CCCR_CAP_SRW 0x04 /* supports read-wait protocol */
	111	#define SDIO_CCCR_CAP_SBS 0x08 /* supports suspend/resume */
	112	#define SDIO_CCCR_CAP_S4MI 0x10 /* interrupt during 4-bit CMD53 */
	113	#define SDIO_CCCR_CAP_E4MI 0x20 /* enable ints during 4-bit CMD53 */
	114	#define SDIO_CCCR_CAP_LSC 0x40 /* low speed card */
	115	#define SDIO_CCCR_CAP_4BLS 0x80 /* 4 bit low speed card */
	116
	117	#define SDIO_CCCR_CIS 0x09 /* common CIS pointer (3 bytes) */
	118
	119	/* Following 4 regs are valid only if SBS is set */
	120	#define SDIO_CCCR_SUSPEND 0x0c
	121	#define SDIO_CCCR_SELx 0x0d
	122	#define SDIO_CCCR_EXECx 0x0e
	123	#define SDIO_CCCR_READYx 0x0f
	124
	125	#define SDIO_CCCR_BLKSIZE 0x10
	126
	127	#define SDIO_CCCR_POWER 0x12
	128
	129	#define SDIO_POWER_SMPC 0x01 /* Supports Master Power Control */
	130	#define SDIO_POWER_EMPC 0x02 /* Enable Master Power Control */
	131
	132	#define SDIO_CCCR_SPEED 0x13
	133
	134	#define SDIO_SPEED_SHS 0x01 /* Supports High-Speed mode */
	135	#define SDIO_SPEED_EHS 0x02 /* Enable High-Speed mode */
	136
	137	/*
	138	* Function Basic Registers (FBR)
	139	*/
	140
7616ee95 DV	141	#define SDIO_FBR_BASE(f) ((f) * 0x100) /* base of function f's FBRs */
7616ee95 DV	142
fa64efa1 PO	143	#define SDIO_FBR_STD_IF 0x00
	144
	145	#define SDIO_FBR_SUPPORTS_CSA 0x40 /* supports Code Storage Area */
	146	#define SDIO_FBR_ENABLE_CSA 0x80 /* enable Code Storage Area */
	147
	148	#define SDIO_FBR_STD_IF_EXT 0x01
	149
	150	#define SDIO_FBR_POWER 0x02
	151
	152	#define SDIO_FBR_POWER_SPS 0x01 /* Supports Power Selection */
	153	#define SDIO_FBR_POWER_EPS 0x02 /* Enable (low) Power Selection */
	154
	155	#define SDIO_FBR_CIS 0x09 /* CIS pointer (3 bytes) */
	156
	157
	158	#define SDIO_FBR_CSA 0x0C /* CSA pointer (3 bytes) */
	159
	160	#define SDIO_FBR_CSA_DATA 0x0F
	161
	162	#define SDIO_FBR_BLKSIZE 0x10 /* block size (2 bytes) */
	163
5c4e6f13 PO	164	#endif
5c4e6f13 PO	165