]>
Commit | Line | Data |
---|---|---|
ecdfa446 GKH |
1 | /****************************************************************************** |
2 | * Copyright(c) 2008 - 2010 Realtek Corporation. All rights reserved. | |
3 | * Linux device driver for RTL8190P / RTL8192E | |
4 | * | |
5 | * Based on the r8180 driver, which is: | |
6 | * Copyright 2004-2005 Andrea Merello <andreamrl@tiscali.it>, et al. | |
7 | * This program is free software; you can redistribute it and/or modify it | |
8 | * under the terms of version 2 of the GNU General Public License as | |
9 | * published by the Free Software Foundation. | |
10 | * | |
11 | * This program is distributed in the hope that it will be useful, but WITHOUT | |
12 | * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or | |
13 | * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for | |
14 | * more details. | |
15 | * | |
16 | * You should have received a copy of the GNU General Public License along with | |
17 | * this program; if not, write to the Free Software Foundation, Inc., | |
18 | * 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA | |
19 | * | |
20 | * The full GNU General Public License is included in this distribution in the | |
21 | * file called LICENSE. | |
22 | * | |
23 | * Contact Information: | |
24 | * Jerry chuang <wlanfae@realtek.com> | |
25 | */ | |
26 | ||
ecdfa446 GKH |
27 | |
28 | #undef LOOP_TEST | |
29 | #undef RX_DONT_PASS_UL | |
30 | #undef DEBUG_EPROM | |
31 | #undef DEBUG_RX_VERBOSE | |
32 | #undef DUMMY_RX | |
33 | #undef DEBUG_ZERO_RX | |
34 | #undef DEBUG_RX_SKB | |
35 | #undef DEBUG_TX_FRAG | |
36 | #undef DEBUG_RX_FRAG | |
37 | #undef DEBUG_TX_FILLDESC | |
38 | #undef DEBUG_TX | |
39 | #undef DEBUG_IRQ | |
40 | #undef DEBUG_RX | |
41 | #undef DEBUG_RXALLOC | |
42 | #undef DEBUG_REGISTERS | |
43 | #undef DEBUG_RING | |
44 | #undef DEBUG_IRQ_TASKLET | |
45 | #undef DEBUG_TX_ALLOC | |
46 | #undef DEBUG_TX_DESC | |
47 | ||
48 | //#define CONFIG_RTL8192_IO_MAP | |
3d14b518 | 49 | #include <linux/vmalloc.h> |
ecdfa446 GKH |
50 | #include <asm/uaccess.h> |
51 | #include "r8192E_hw.h" | |
52 | #include "r8192E.h" | |
53 | #include "r8190_rtl8256.h" /* RTL8225 Radio frontend */ | |
54 | #include "r8180_93cx6.h" /* Card EEPROM */ | |
55 | #include "r8192E_wx.h" | |
56 | #include "r819xE_phy.h" //added by WB 4.30.2008 | |
57 | #include "r819xE_phyreg.h" | |
58 | #include "r819xE_cmdpkt.h" | |
59 | #include "r8192E_dm.h" | |
60 | //#include "r8192xU_phyreg.h" | |
61 | //#include <linux/usb.h> | |
62 | // FIXME: check if 2.6.7 is ok | |
63 | ||
64 | #ifdef CONFIG_PM_RTL | |
65 | #include "r8192_pm.h" | |
66 | #endif | |
67 | ||
68 | #ifdef ENABLE_DOT11D | |
65a43784 | 69 | #include "ieee80211/dot11d.h" |
ecdfa446 GKH |
70 | #endif |
71 | ||
72 | //set here to open your trace code. //WB | |
73 | u32 rt_global_debug_component = \ | |
74 | // COMP_INIT | | |
75 | // COMP_EPROM | | |
76 | // COMP_PHY | | |
77 | // COMP_RF | | |
65a43784 | 78 | // COMP_FIRMWARE | |
ecdfa446 GKH |
79 | // COMP_TRACE | |
80 | // COMP_DOWN | | |
81 | // COMP_SWBW | | |
82 | // COMP_SEC | | |
83 | // COMP_QOS | | |
84 | // COMP_RATE | | |
85 | // COMP_RECV | | |
86 | // COMP_SEND | | |
87 | // COMP_POWER | | |
88 | // COMP_EVENTS | | |
89 | // COMP_RESET | | |
90 | // COMP_CMDPKT | | |
91 | // COMP_POWER_TRACKING | | |
92 | // COMP_INTR | | |
93 | COMP_ERR ; //always open err flags on | |
94 | #ifndef PCI_DEVICE | |
95 | #define PCI_DEVICE(vend,dev)\ | |
96 | .vendor=(vend),.device=(dev),\ | |
97 | .subvendor=PCI_ANY_ID,.subdevice=PCI_ANY_ID | |
98 | #endif | |
99 | static struct pci_device_id rtl8192_pci_id_tbl[] __devinitdata = { | |
100 | #ifdef RTL8190P | |
101 | /* Realtek */ | |
102 | /* Dlink */ | |
103 | { PCI_DEVICE(0x10ec, 0x8190) }, | |
104 | /* Corega */ | |
105 | { PCI_DEVICE(0x07aa, 0x0045) }, | |
106 | { PCI_DEVICE(0x07aa, 0x0046) }, | |
107 | #else | |
108 | /* Realtek */ | |
109 | { PCI_DEVICE(0x10ec, 0x8192) }, | |
110 | ||
111 | /* Corega */ | |
112 | { PCI_DEVICE(0x07aa, 0x0044) }, | |
113 | { PCI_DEVICE(0x07aa, 0x0047) }, | |
114 | #endif | |
115 | {} | |
116 | }; | |
117 | ||
118 | static char* ifname = "wlan%d"; | |
ecdfa446 GKH |
119 | static int hwwep = 1; //default use hw. set 0 to use software security |
120 | static int channels = 0x3fff; | |
121 | ||
122 | MODULE_LICENSE("GPL"); | |
ecdfa446 | 123 | MODULE_VERSION("V 1.1"); |
ecdfa446 GKH |
124 | MODULE_DEVICE_TABLE(pci, rtl8192_pci_id_tbl); |
125 | //MODULE_AUTHOR("Andrea Merello <andreamrl@tiscali.it>"); | |
126 | MODULE_DESCRIPTION("Linux driver for Realtek RTL819x WiFi cards"); | |
127 | ||
ecdfa446 | 128 | |
ecdfa446 GKH |
129 | module_param(ifname, charp, S_IRUGO|S_IWUSR ); |
130 | //module_param(hwseqnum,int, S_IRUGO|S_IWUSR); | |
131 | module_param(hwwep,int, S_IRUGO|S_IWUSR); | |
132 | module_param(channels,int, S_IRUGO|S_IWUSR); | |
ecdfa446 GKH |
133 | |
134 | MODULE_PARM_DESC(ifname," Net interface name, wlan%d=default"); | |
135 | //MODULE_PARM_DESC(hwseqnum," Try to use hardware 802.11 header sequence numbers. Zero=default"); | |
136 | MODULE_PARM_DESC(hwwep," Try to use hardware WEP support. Still broken and not available on all cards"); | |
137 | MODULE_PARM_DESC(channels," Channel bitmask for specific locales. NYI"); | |
138 | ||
139 | static int __devinit rtl8192_pci_probe(struct pci_dev *pdev, | |
140 | const struct pci_device_id *id); | |
141 | static void __devexit rtl8192_pci_disconnect(struct pci_dev *pdev); | |
142 | ||
143 | static struct pci_driver rtl8192_pci_driver = { | |
144 | .name = RTL819xE_MODULE_NAME, /* Driver name */ | |
145 | .id_table = rtl8192_pci_id_tbl, /* PCI_ID table */ | |
146 | .probe = rtl8192_pci_probe, /* probe fn */ | |
147 | .remove = __devexit_p(rtl8192_pci_disconnect), /* remove fn */ | |
ecdfa446 GKH |
148 | #ifdef CONFIG_PM_RTL |
149 | .suspend = rtl8192E_suspend, /* PM suspend fn */ | |
150 | .resume = rtl8192E_resume, /* PM resume fn */ | |
151 | #else | |
152 | .suspend = NULL, /* PM suspend fn */ | |
153 | .resume = NULL, /* PM resume fn */ | |
154 | #endif | |
ecdfa446 GKH |
155 | }; |
156 | ||
157 | #ifdef ENABLE_DOT11D | |
158 | ||
159 | typedef struct _CHANNEL_LIST | |
160 | { | |
161 | u8 Channel[32]; | |
162 | u8 Len; | |
163 | }CHANNEL_LIST, *PCHANNEL_LIST; | |
164 | ||
165 | static CHANNEL_LIST ChannelPlan[] = { | |
166 | {{1,2,3,4,5,6,7,8,9,10,11,36,40,44,48,52,56,60,64,149,153,157,161,165},24}, //FCC | |
167 | {{1,2,3,4,5,6,7,8,9,10,11},11}, //IC | |
168 | {{1,2,3,4,5,6,7,8,9,10,11,12,13,36,40,44,48,52,56,60,64},21}, //ETSI | |
169 | {{1,2,3,4,5,6,7,8,9,10,11,12,13},13}, //Spain. Change to ETSI. | |
170 | {{1,2,3,4,5,6,7,8,9,10,11,12,13},13}, //France. Change to ETSI. | |
171 | {{1,2,3,4,5,6,7,8,9,10,11,12,13,14,36,40,44,48,52,56,60,64},22}, //MKK //MKK | |
172 | {{1,2,3,4,5,6,7,8,9,10,11,12,13,14,36,40,44,48,52,56,60,64},22},//MKK1 | |
173 | {{1,2,3,4,5,6,7,8,9,10,11,12,13},13}, //Israel. | |
174 | {{1,2,3,4,5,6,7,8,9,10,11,12,13,14,36,40,44,48,52,56,60,64},22}, // For 11a , TELEC | |
175 | {{1,2,3,4,5,6,7,8,9,10,11,12,13,14,36,40,44,48,52,56,60,64}, 22}, //MIC | |
176 | {{1,2,3,4,5,6,7,8,9,10,11,12,13,14},14} //For Global Domain. 1-11:active scan, 12-14 passive scan. //+YJ, 080626 | |
177 | }; | |
178 | ||
179 | static void rtl819x_set_channel_map(u8 channel_plan, struct r8192_priv* priv) | |
180 | { | |
181 | int i, max_chan=-1, min_chan=-1; | |
182 | struct ieee80211_device* ieee = priv->ieee80211; | |
183 | switch (channel_plan) | |
184 | { | |
185 | case COUNTRY_CODE_FCC: | |
186 | case COUNTRY_CODE_IC: | |
187 | case COUNTRY_CODE_ETSI: | |
188 | case COUNTRY_CODE_SPAIN: | |
189 | case COUNTRY_CODE_FRANCE: | |
190 | case COUNTRY_CODE_MKK: | |
191 | case COUNTRY_CODE_MKK1: | |
192 | case COUNTRY_CODE_ISRAEL: | |
193 | case COUNTRY_CODE_TELEC: | |
194 | case COUNTRY_CODE_MIC: | |
195 | { | |
196 | Dot11d_Init(ieee); | |
197 | ieee->bGlobalDomain = false; | |
198 | //acturally 8225 & 8256 rf chip only support B,G,24N mode | |
199 | if ((priv->rf_chip == RF_8225) || (priv->rf_chip == RF_8256)) | |
200 | { | |
201 | min_chan = 1; | |
202 | max_chan = 14; | |
203 | } | |
204 | else | |
205 | { | |
206 | RT_TRACE(COMP_ERR, "unknown rf chip, can't set channel map in function:%s()\n", __FUNCTION__); | |
207 | } | |
208 | if (ChannelPlan[channel_plan].Len != 0){ | |
209 | // Clear old channel map | |
210 | memset(GET_DOT11D_INFO(ieee)->channel_map, 0, sizeof(GET_DOT11D_INFO(ieee)->channel_map)); | |
211 | // Set new channel map | |
212 | for (i=0;i<ChannelPlan[channel_plan].Len;i++) | |
213 | { | |
214 | if (ChannelPlan[channel_plan].Channel[i] < min_chan || ChannelPlan[channel_plan].Channel[i] > max_chan) | |
215 | break; | |
216 | GET_DOT11D_INFO(ieee)->channel_map[ChannelPlan[channel_plan].Channel[i]] = 1; | |
217 | } | |
218 | } | |
219 | break; | |
220 | } | |
221 | case COUNTRY_CODE_GLOBAL_DOMAIN: | |
222 | { | |
223 | GET_DOT11D_INFO(ieee)->bEnabled = 0; //this flag enabled to follow 11d country IE setting, otherwise, it shall follow global domain setting | |
224 | Dot11d_Reset(ieee); | |
225 | ieee->bGlobalDomain = true; | |
226 | break; | |
227 | } | |
228 | default: | |
229 | break; | |
230 | } | |
231 | } | |
232 | #endif | |
233 | ||
234 | ||
235 | #define eqMacAddr(a,b) ( ((a)[0]==(b)[0] && (a)[1]==(b)[1] && (a)[2]==(b)[2] && (a)[3]==(b)[3] && (a)[4]==(b)[4] && (a)[5]==(b)[5]) ? 1:0 ) | |
236 | /* 2007/07/25 MH Defien temp tx fw info. */ | |
5e1ad18a | 237 | static TX_FWINFO_T Tmp_TxFwInfo; |
ecdfa446 GKH |
238 | |
239 | ||
240 | #define rx_hal_is_cck_rate(_pdrvinfo)\ | |
241 | (_pdrvinfo->RxRate == DESC90_RATE1M ||\ | |
242 | _pdrvinfo->RxRate == DESC90_RATE2M ||\ | |
243 | _pdrvinfo->RxRate == DESC90_RATE5_5M ||\ | |
244 | _pdrvinfo->RxRate == DESC90_RATE11M) &&\ | |
245 | !_pdrvinfo->RxHT\ | |
246 | ||
247 | ||
248 | void CamResetAllEntry(struct net_device *dev) | |
249 | { | |
250 | //u8 ucIndex; | |
251 | u32 ulcommand = 0; | |
252 | ||
253 | #if 1 | |
254 | ulcommand |= BIT31|BIT30; | |
255 | write_nic_dword(dev, RWCAM, ulcommand); | |
256 | #else | |
257 | for(ucIndex=0;ucIndex<TOTAL_CAM_ENTRY;ucIndex++) | |
258 | CAM_mark_invalid(dev, ucIndex); | |
259 | for(ucIndex=0;ucIndex<TOTAL_CAM_ENTRY;ucIndex++) | |
260 | CAM_empty_entry(dev, ucIndex); | |
261 | #endif | |
262 | } | |
263 | ||
264 | ||
265 | void write_cam(struct net_device *dev, u8 addr, u32 data) | |
266 | { | |
267 | write_nic_dword(dev, WCAMI, data); | |
268 | write_nic_dword(dev, RWCAM, BIT31|BIT16|(addr&0xff) ); | |
269 | } | |
270 | u32 read_cam(struct net_device *dev, u8 addr) | |
271 | { | |
272 | write_nic_dword(dev, RWCAM, 0x80000000|(addr&0xff) ); | |
273 | return read_nic_dword(dev, 0xa8); | |
274 | } | |
275 | ||
276 | //////////////////////////////////////////////////////////// | |
277 | #ifdef CONFIG_RTL8180_IO_MAP | |
278 | ||
279 | u8 read_nic_byte(struct net_device *dev, int x) | |
280 | { | |
281 | return 0xff&inb(dev->base_addr +x); | |
282 | } | |
283 | ||
284 | u32 read_nic_dword(struct net_device *dev, int x) | |
285 | { | |
286 | return inl(dev->base_addr +x); | |
287 | } | |
288 | ||
289 | u16 read_nic_word(struct net_device *dev, int x) | |
290 | { | |
291 | return inw(dev->base_addr +x); | |
292 | } | |
293 | ||
294 | void write_nic_byte(struct net_device *dev, int x,u8 y) | |
295 | { | |
296 | outb(y&0xff,dev->base_addr +x); | |
297 | } | |
298 | ||
299 | void write_nic_word(struct net_device *dev, int x,u16 y) | |
300 | { | |
301 | outw(y,dev->base_addr +x); | |
302 | } | |
303 | ||
304 | void write_nic_dword(struct net_device *dev, int x,u32 y) | |
305 | { | |
306 | outl(y,dev->base_addr +x); | |
307 | } | |
308 | ||
309 | #else /* RTL_IO_MAP */ | |
310 | ||
311 | u8 read_nic_byte(struct net_device *dev, int x) | |
312 | { | |
313 | return 0xff&readb((u8*)dev->mem_start +x); | |
314 | } | |
315 | ||
316 | u32 read_nic_dword(struct net_device *dev, int x) | |
317 | { | |
318 | return readl((u8*)dev->mem_start +x); | |
319 | } | |
320 | ||
321 | u16 read_nic_word(struct net_device *dev, int x) | |
322 | { | |
323 | return readw((u8*)dev->mem_start +x); | |
324 | } | |
325 | ||
326 | void write_nic_byte(struct net_device *dev, int x,u8 y) | |
327 | { | |
328 | writeb(y,(u8*)dev->mem_start +x); | |
329 | udelay(20); | |
330 | } | |
331 | ||
332 | void write_nic_dword(struct net_device *dev, int x,u32 y) | |
333 | { | |
334 | writel(y,(u8*)dev->mem_start +x); | |
335 | udelay(20); | |
336 | } | |
337 | ||
338 | void write_nic_word(struct net_device *dev, int x,u16 y) | |
339 | { | |
340 | writew(y,(u8*)dev->mem_start +x); | |
341 | udelay(20); | |
342 | } | |
343 | ||
344 | #endif /* RTL_IO_MAP */ | |
345 | ||
65a43784 | 346 | u8 rtl8192e_ap_sec_type(struct ieee80211_device *ieee) |
347 | { | |
348 | //struct r8192_priv* priv = ieee80211_priv(dev); | |
349 | //struct ieee80211_device *ieee = priv->ieee80211; | |
350 | ||
351 | static u8 ccmp_ie[4] = {0x00,0x50,0xf2,0x04}; | |
352 | static u8 ccmp_rsn_ie[4] = {0x00, 0x0f, 0xac, 0x04}; | |
353 | int wpa_ie_len= ieee->wpa_ie_len; | |
354 | struct ieee80211_crypt_data* crypt; | |
355 | int encrypt; | |
356 | ||
357 | crypt = ieee->crypt[ieee->tx_keyidx]; | |
358 | ||
359 | encrypt = (ieee->current_network.capability & WLAN_CAPABILITY_PRIVACY) ||\ | |
360 | (ieee->host_encrypt && crypt && crypt->ops && \ | |
361 | (0 == strcmp(crypt->ops->name,"WEP"))); | |
362 | ||
363 | /* simply judge */ | |
364 | if(encrypt && (wpa_ie_len == 0)) { | |
365 | // wep encryption, no N mode setting */ | |
366 | return SEC_ALG_WEP; | |
367 | } else if((wpa_ie_len != 0)) { | |
368 | // parse pairwise key type */ | |
369 | if (((ieee->wpa_ie[0] == 0xdd) && (!memcmp(&(ieee->wpa_ie[14]),ccmp_ie,4))) || | |
370 | ((ieee->wpa_ie[0] == 0x30) && (!memcmp(&ieee->wpa_ie[10],ccmp_rsn_ie, 4)))) | |
371 | return SEC_ALG_CCMP; | |
372 | else | |
373 | return SEC_ALG_TKIP; | |
374 | } else { | |
375 | return SEC_ALG_NONE; | |
376 | } | |
377 | } | |
378 | ||
379 | void | |
380 | rtl8192e_SetHwReg(struct net_device *dev,u8 variable,u8* val) | |
381 | { | |
382 | struct r8192_priv* priv = ieee80211_priv(dev); | |
383 | ||
384 | switch(variable) | |
385 | { | |
386 | ||
387 | case HW_VAR_BSSID: | |
388 | write_nic_dword(dev, BSSIDR, ((u32*)(val))[0]); | |
389 | write_nic_word(dev, BSSIDR+2, ((u16*)(val+2))[0]); | |
390 | break; | |
391 | ||
392 | case HW_VAR_MEDIA_STATUS: | |
393 | { | |
394 | RT_OP_MODE OpMode = *((RT_OP_MODE *)(val)); | |
395 | //LED_CTL_MODE LedAction = LED_CTL_NO_LINK; | |
396 | u8 btMsr = read_nic_byte(dev, MSR); | |
397 | ||
398 | btMsr &= 0xfc; | |
399 | ||
400 | switch(OpMode) | |
401 | { | |
402 | case RT_OP_MODE_INFRASTRUCTURE: | |
403 | btMsr |= MSR_INFRA; | |
404 | //LedAction = LED_CTL_LINK; | |
405 | break; | |
406 | ||
407 | case RT_OP_MODE_IBSS: | |
408 | btMsr |= MSR_ADHOC; | |
409 | // led link set seperate | |
410 | break; | |
411 | ||
412 | case RT_OP_MODE_AP: | |
413 | btMsr |= MSR_AP; | |
414 | //LedAction = LED_CTL_LINK; | |
415 | break; | |
416 | ||
417 | default: | |
418 | btMsr |= MSR_NOLINK; | |
419 | break; | |
420 | } | |
421 | ||
422 | write_nic_byte(dev, MSR, btMsr); | |
423 | ||
424 | //priv->ieee80211->LedControlHandler(dev, LedAction); | |
425 | } | |
426 | break; | |
427 | ||
428 | case HW_VAR_CECHK_BSSID: | |
429 | { | |
430 | u32 RegRCR, Type; | |
431 | ||
432 | Type = ((u8*)(val))[0]; | |
433 | //priv->ieee80211->GetHwRegHandler(dev, HW_VAR_RCR, (u8*)(&RegRCR)); | |
434 | RegRCR = read_nic_dword(dev,RCR); | |
435 | priv->ReceiveConfig = RegRCR; | |
436 | ||
437 | if (Type == true) | |
438 | RegRCR |= (RCR_CBSSID); | |
439 | else if (Type == false) | |
440 | RegRCR &= (~RCR_CBSSID); | |
441 | ||
442 | //priv->ieee80211->SetHwRegHandler( dev, HW_VAR_RCR, (u8*)(&RegRCR) ); | |
443 | write_nic_dword(dev, RCR,RegRCR); | |
444 | priv->ReceiveConfig = RegRCR; | |
445 | ||
446 | } | |
447 | break; | |
448 | ||
449 | case HW_VAR_SLOT_TIME: | |
450 | { | |
451 | //PSTA_QOS pStaQos = Adapter->MgntInfo.pStaQos; | |
452 | //AC_CODING eACI; | |
453 | ||
454 | priv->slot_time = val[0]; | |
455 | write_nic_byte(dev, SLOT_TIME, val[0]); | |
456 | ||
457 | } | |
458 | break; | |
459 | ||
460 | case HW_VAR_ACK_PREAMBLE: | |
461 | { | |
462 | u32 regTmp = 0; | |
463 | priv->short_preamble = (bool)(*(u8*)val ); | |
464 | regTmp = priv->basic_rate; | |
465 | if (priv->short_preamble) | |
466 | regTmp |= BRSR_AckShortPmb; | |
467 | write_nic_dword(dev, RRSR, regTmp); | |
468 | } | |
469 | break; | |
470 | ||
471 | case HW_VAR_CPU_RST: | |
472 | write_nic_dword(dev, CPU_GEN, ((u32*)(val))[0]); | |
473 | break; | |
474 | ||
475 | default: | |
476 | break; | |
477 | } | |
478 | ||
479 | } | |
480 | ||
ecdfa446 GKH |
481 | |
482 | /////////////////////////////////////////////////////////// | |
483 | ||
484 | //u8 read_phy_cck(struct net_device *dev, u8 adr); | |
485 | //u8 read_phy_ofdm(struct net_device *dev, u8 adr); | |
486 | /* this might still called in what was the PHY rtl8185/rtl8192 common code | |
487 | * plans are to possibilty turn it again in one common code... | |
488 | */ | |
489 | inline void force_pci_posting(struct net_device *dev) | |
490 | { | |
491 | } | |
492 | ||
493 | ||
494 | //warning message WB | |
ecdfa446 | 495 | irqreturn_t rtl8192_interrupt(int irq, void *netdev); |
ecdfa446 GKH |
496 | //static struct net_device_stats *rtl8192_stats(struct net_device *dev); |
497 | void rtl8192_commit(struct net_device *dev); | |
498 | //void rtl8192_restart(struct net_device *dev); | |
ecdfa446 GKH |
499 | void rtl8192_restart(struct work_struct *work); |
500 | //void rtl8192_rq_tx_ack(struct work_struct *work); | |
ecdfa446 GKH |
501 | |
502 | void watch_dog_timer_callback(unsigned long data); | |
ecdfa446 GKH |
503 | /**************************************************************************** |
504 | -----------------------------PROCFS STUFF------------------------- | |
505 | *****************************************************************************/ | |
506 | ||
507 | static struct proc_dir_entry *rtl8192_proc = NULL; | |
508 | ||
509 | ||
510 | ||
511 | static int proc_get_stats_ap(char *page, char **start, | |
512 | off_t offset, int count, | |
513 | int *eof, void *data) | |
514 | { | |
515 | struct net_device *dev = data; | |
516 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
517 | struct ieee80211_device *ieee = priv->ieee80211; | |
518 | struct ieee80211_network *target; | |
519 | ||
520 | int len = 0; | |
521 | ||
522 | list_for_each_entry(target, &ieee->network_list, list) { | |
523 | ||
524 | len += snprintf(page + len, count - len, | |
525 | "%s ", target->ssid); | |
526 | ||
527 | if(target->wpa_ie_len>0 || target->rsn_ie_len>0){ | |
528 | len += snprintf(page + len, count - len, | |
529 | "WPA\n"); | |
530 | } | |
531 | else{ | |
532 | len += snprintf(page + len, count - len, | |
533 | "non_WPA\n"); | |
534 | } | |
535 | ||
536 | } | |
537 | ||
538 | *eof = 1; | |
539 | return len; | |
540 | } | |
541 | ||
542 | static int proc_get_registers(char *page, char **start, | |
543 | off_t offset, int count, | |
544 | int *eof, void *data) | |
545 | { | |
546 | struct net_device *dev = data; | |
547 | // struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
548 | ||
549 | int len = 0; | |
550 | int i,n; | |
551 | ||
552 | int max=0xff; | |
553 | ||
554 | /* This dump the current register page */ | |
555 | len += snprintf(page + len, count - len, | |
556 | "\n####################page 0##################\n "); | |
557 | ||
558 | for(n=0;n<=max;) | |
559 | { | |
560 | //printk( "\nD: %2x> ", n); | |
561 | len += snprintf(page + len, count - len, | |
562 | "\nD: %2x > ",n); | |
563 | ||
564 | for(i=0;i<16 && n<=max;i++,n++) | |
565 | len += snprintf(page + len, count - len, | |
566 | "%2x ",read_nic_byte(dev,n)); | |
567 | ||
568 | // printk("%2x ",read_nic_byte(dev,n)); | |
569 | } | |
570 | len += snprintf(page + len, count - len,"\n"); | |
571 | len += snprintf(page + len, count - len, | |
572 | "\n####################page 1##################\n "); | |
573 | for(n=0;n<=max;) | |
574 | { | |
575 | //printk( "\nD: %2x> ", n); | |
576 | len += snprintf(page + len, count - len, | |
577 | "\nD: %2x > ",n); | |
578 | ||
579 | for(i=0;i<16 && n<=max;i++,n++) | |
580 | len += snprintf(page + len, count - len, | |
581 | "%2x ",read_nic_byte(dev,0x100|n)); | |
582 | ||
583 | // printk("%2x ",read_nic_byte(dev,n)); | |
584 | } | |
585 | ||
586 | len += snprintf(page + len, count - len, | |
587 | "\n####################page 3##################\n "); | |
588 | for(n=0;n<=max;) | |
589 | { | |
590 | //printk( "\nD: %2x> ", n); | |
591 | len += snprintf(page + len, count - len, | |
592 | "\nD: %2x > ",n); | |
593 | ||
594 | for(i=0;i<16 && n<=max;i++,n++) | |
595 | len += snprintf(page + len, count - len, | |
596 | "%2x ",read_nic_byte(dev,0x300|n)); | |
597 | ||
598 | // printk("%2x ",read_nic_byte(dev,n)); | |
599 | } | |
600 | ||
601 | ||
602 | *eof = 1; | |
603 | return len; | |
604 | ||
605 | } | |
606 | ||
607 | ||
ecdfa446 GKH |
608 | |
609 | static int proc_get_stats_tx(char *page, char **start, | |
610 | off_t offset, int count, | |
611 | int *eof, void *data) | |
612 | { | |
613 | struct net_device *dev = data; | |
614 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
615 | ||
616 | int len = 0; | |
617 | ||
618 | len += snprintf(page + len, count - len, | |
619 | "TX VI priority ok int: %lu\n" | |
620 | // "TX VI priority error int: %lu\n" | |
621 | "TX VO priority ok int: %lu\n" | |
622 | // "TX VO priority error int: %lu\n" | |
623 | "TX BE priority ok int: %lu\n" | |
624 | // "TX BE priority error int: %lu\n" | |
625 | "TX BK priority ok int: %lu\n" | |
626 | // "TX BK priority error int: %lu\n" | |
627 | "TX MANAGE priority ok int: %lu\n" | |
628 | // "TX MANAGE priority error int: %lu\n" | |
629 | "TX BEACON priority ok int: %lu\n" | |
630 | "TX BEACON priority error int: %lu\n" | |
631 | "TX CMDPKT priority ok int: %lu\n" | |
632 | // "TX high priority ok int: %lu\n" | |
633 | // "TX high priority failed error int: %lu\n" | |
634 | // "TX queue resume: %lu\n" | |
635 | "TX queue stopped?: %d\n" | |
636 | "TX fifo overflow: %lu\n" | |
637 | // "TX beacon: %lu\n" | |
638 | // "TX VI queue: %d\n" | |
639 | // "TX VO queue: %d\n" | |
640 | // "TX BE queue: %d\n" | |
641 | // "TX BK queue: %d\n" | |
642 | // "TX HW queue: %d\n" | |
643 | // "TX VI dropped: %lu\n" | |
644 | // "TX VO dropped: %lu\n" | |
645 | // "TX BE dropped: %lu\n" | |
646 | // "TX BK dropped: %lu\n" | |
647 | "TX total data packets %lu\n" | |
648 | "TX total data bytes :%lu\n", | |
649 | // "TX beacon aborted: %lu\n", | |
650 | priv->stats.txviokint, | |
651 | // priv->stats.txvierr, | |
652 | priv->stats.txvookint, | |
653 | // priv->stats.txvoerr, | |
654 | priv->stats.txbeokint, | |
655 | // priv->stats.txbeerr, | |
656 | priv->stats.txbkokint, | |
657 | // priv->stats.txbkerr, | |
658 | priv->stats.txmanageokint, | |
659 | // priv->stats.txmanageerr, | |
660 | priv->stats.txbeaconokint, | |
661 | priv->stats.txbeaconerr, | |
662 | priv->stats.txcmdpktokint, | |
663 | // priv->stats.txhpokint, | |
664 | // priv->stats.txhperr, | |
665 | // priv->stats.txresumed, | |
666 | netif_queue_stopped(dev), | |
667 | priv->stats.txoverflow, | |
668 | // priv->stats.txbeacon, | |
669 | // atomic_read(&(priv->tx_pending[VI_QUEUE])), | |
670 | // atomic_read(&(priv->tx_pending[VO_QUEUE])), | |
671 | // atomic_read(&(priv->tx_pending[BE_QUEUE])), | |
672 | // atomic_read(&(priv->tx_pending[BK_QUEUE])), | |
673 | // read_nic_byte(dev, TXFIFOCOUNT), | |
674 | // priv->stats.txvidrop, | |
675 | // priv->stats.txvodrop, | |
676 | priv->ieee80211->stats.tx_packets, | |
677 | priv->ieee80211->stats.tx_bytes | |
678 | ||
679 | ||
680 | // priv->stats.txbedrop, | |
681 | // priv->stats.txbkdrop | |
682 | // priv->stats.txdatapkt | |
683 | // priv->stats.txbeaconerr | |
684 | ); | |
685 | ||
686 | *eof = 1; | |
687 | return len; | |
688 | } | |
689 | ||
690 | ||
691 | ||
692 | static int proc_get_stats_rx(char *page, char **start, | |
693 | off_t offset, int count, | |
694 | int *eof, void *data) | |
695 | { | |
696 | struct net_device *dev = data; | |
697 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
698 | ||
699 | int len = 0; | |
700 | ||
701 | len += snprintf(page + len, count - len, | |
702 | "RX packets: %lu\n" | |
703 | "RX desc err: %lu\n" | |
704 | "RX rx overflow error: %lu\n" | |
705 | "RX invalid urb error: %lu\n", | |
706 | priv->stats.rxint, | |
707 | priv->stats.rxrdu, | |
708 | priv->stats.rxoverflow, | |
709 | priv->stats.rxurberr); | |
710 | ||
711 | *eof = 1; | |
712 | return len; | |
713 | } | |
714 | ||
5e1ad18a | 715 | static void rtl8192_proc_module_init(void) |
ecdfa446 GKH |
716 | { |
717 | RT_TRACE(COMP_INIT, "Initializing proc filesystem"); | |
ecdfa446 | 718 | rtl8192_proc=create_proc_entry(RTL819xE_MODULE_NAME, S_IFDIR, init_net.proc_net); |
ecdfa446 GKH |
719 | } |
720 | ||
721 | ||
5e1ad18a | 722 | static void rtl8192_proc_module_remove(void) |
ecdfa446 | 723 | { |
ecdfa446 | 724 | remove_proc_entry(RTL819xE_MODULE_NAME, init_net.proc_net); |
ecdfa446 GKH |
725 | } |
726 | ||
727 | ||
5e1ad18a | 728 | static void rtl8192_proc_remove_one(struct net_device *dev) |
ecdfa446 GKH |
729 | { |
730 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
731 | ||
732 | printk("dev name=======> %s\n",dev->name); | |
733 | ||
734 | if (priv->dir_dev) { | |
735 | // remove_proc_entry("stats-hw", priv->dir_dev); | |
736 | remove_proc_entry("stats-tx", priv->dir_dev); | |
737 | remove_proc_entry("stats-rx", priv->dir_dev); | |
738 | // remove_proc_entry("stats-ieee", priv->dir_dev); | |
739 | remove_proc_entry("stats-ap", priv->dir_dev); | |
740 | remove_proc_entry("registers", priv->dir_dev); | |
741 | // remove_proc_entry("cck-registers",priv->dir_dev); | |
742 | // remove_proc_entry("ofdm-registers",priv->dir_dev); | |
743 | //remove_proc_entry(dev->name, rtl8192_proc); | |
744 | remove_proc_entry("wlan0", rtl8192_proc); | |
745 | priv->dir_dev = NULL; | |
746 | } | |
747 | } | |
748 | ||
749 | ||
5e1ad18a | 750 | static void rtl8192_proc_init_one(struct net_device *dev) |
ecdfa446 GKH |
751 | { |
752 | struct proc_dir_entry *e; | |
753 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
754 | priv->dir_dev = create_proc_entry(dev->name, | |
755 | S_IFDIR | S_IRUGO | S_IXUGO, | |
756 | rtl8192_proc); | |
757 | if (!priv->dir_dev) { | |
758 | RT_TRACE(COMP_ERR, "Unable to initialize /proc/net/rtl8192/%s\n", | |
759 | dev->name); | |
760 | return; | |
761 | } | |
ecdfa446 GKH |
762 | e = create_proc_read_entry("stats-rx", S_IFREG | S_IRUGO, |
763 | priv->dir_dev, proc_get_stats_rx, dev); | |
764 | ||
765 | if (!e) { | |
766 | RT_TRACE(COMP_ERR,"Unable to initialize " | |
767 | "/proc/net/rtl8192/%s/stats-rx\n", | |
768 | dev->name); | |
769 | } | |
770 | ||
771 | ||
772 | e = create_proc_read_entry("stats-tx", S_IFREG | S_IRUGO, | |
773 | priv->dir_dev, proc_get_stats_tx, dev); | |
774 | ||
775 | if (!e) { | |
776 | RT_TRACE(COMP_ERR, "Unable to initialize " | |
777 | "/proc/net/rtl8192/%s/stats-tx\n", | |
778 | dev->name); | |
779 | } | |
ecdfa446 GKH |
780 | |
781 | e = create_proc_read_entry("stats-ap", S_IFREG | S_IRUGO, | |
782 | priv->dir_dev, proc_get_stats_ap, dev); | |
783 | ||
784 | if (!e) { | |
785 | RT_TRACE(COMP_ERR, "Unable to initialize " | |
786 | "/proc/net/rtl8192/%s/stats-ap\n", | |
787 | dev->name); | |
788 | } | |
789 | ||
790 | e = create_proc_read_entry("registers", S_IFREG | S_IRUGO, | |
791 | priv->dir_dev, proc_get_registers, dev); | |
792 | if (!e) { | |
793 | RT_TRACE(COMP_ERR, "Unable to initialize " | |
794 | "/proc/net/rtl8192/%s/registers\n", | |
795 | dev->name); | |
796 | } | |
ecdfa446 GKH |
797 | } |
798 | /**************************************************************************** | |
799 | -----------------------------MISC STUFF------------------------- | |
800 | *****************************************************************************/ | |
801 | ||
ecdfa446 GKH |
802 | short check_nic_enough_desc(struct net_device *dev, int prio) |
803 | { | |
804 | struct r8192_priv *priv = ieee80211_priv(dev); | |
805 | struct rtl8192_tx_ring *ring = &priv->tx_ring[prio]; | |
806 | ||
807 | /* for now we reserve two free descriptor as a safety boundary | |
808 | * between the tail and the head | |
809 | */ | |
810 | if (ring->entries - skb_queue_len(&ring->queue) >= 2) { | |
811 | return 1; | |
812 | } else { | |
813 | return 0; | |
814 | } | |
815 | } | |
816 | ||
5e1ad18a | 817 | static void tx_timeout(struct net_device *dev) |
ecdfa446 GKH |
818 | { |
819 | struct r8192_priv *priv = ieee80211_priv(dev); | |
820 | //rtl8192_commit(dev); | |
821 | ||
ecdfa446 | 822 | schedule_work(&priv->reset_wq); |
ecdfa446 GKH |
823 | printk("TXTIMEOUT"); |
824 | } | |
825 | ||
826 | ||
ecdfa446 GKH |
827 | /**************************************************************************** |
828 | ------------------------------HW STUFF--------------------------- | |
829 | *****************************************************************************/ | |
830 | ||
831 | ||
5e1ad18a | 832 | static void rtl8192_irq_enable(struct net_device *dev) |
ecdfa446 GKH |
833 | { |
834 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
835 | priv->irq_enabled = 1; | |
836 | write_nic_dword(dev,INTA_MASK, priv->irq_mask); | |
837 | } | |
838 | ||
839 | ||
65a43784 | 840 | void rtl8192_irq_disable(struct net_device *dev) |
ecdfa446 GKH |
841 | { |
842 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
843 | ||
844 | write_nic_dword(dev,INTA_MASK,0); | |
845 | force_pci_posting(dev); | |
846 | priv->irq_enabled = 0; | |
847 | } | |
848 | ||
849 | ||
65a43784 | 850 | #if 0 |
5e1ad18a | 851 | static void rtl8192_set_mode(struct net_device *dev,int mode) |
ecdfa446 GKH |
852 | { |
853 | u8 ecmd; | |
854 | ecmd=read_nic_byte(dev, EPROM_CMD); | |
855 | ecmd=ecmd &~ EPROM_CMD_OPERATING_MODE_MASK; | |
856 | ecmd=ecmd | (mode<<EPROM_CMD_OPERATING_MODE_SHIFT); | |
857 | ecmd=ecmd &~ (1<<EPROM_CS_SHIFT); | |
858 | ecmd=ecmd &~ (1<<EPROM_CK_SHIFT); | |
859 | write_nic_byte(dev, EPROM_CMD, ecmd); | |
860 | } | |
65a43784 | 861 | #endif |
ecdfa446 GKH |
862 | |
863 | void rtl8192_update_msr(struct net_device *dev) | |
864 | { | |
865 | struct r8192_priv *priv = ieee80211_priv(dev); | |
866 | u8 msr; | |
867 | ||
868 | msr = read_nic_byte(dev, MSR); | |
869 | msr &= ~ MSR_LINK_MASK; | |
870 | ||
871 | /* do not change in link_state != WLAN_LINK_ASSOCIATED. | |
872 | * msr must be updated if the state is ASSOCIATING. | |
873 | * this is intentional and make sense for ad-hoc and | |
874 | * master (see the create BSS/IBSS func) | |
875 | */ | |
876 | if (priv->ieee80211->state == IEEE80211_LINKED){ | |
877 | ||
878 | if (priv->ieee80211->iw_mode == IW_MODE_INFRA) | |
879 | msr |= (MSR_LINK_MANAGED<<MSR_LINK_SHIFT); | |
880 | else if (priv->ieee80211->iw_mode == IW_MODE_ADHOC) | |
881 | msr |= (MSR_LINK_ADHOC<<MSR_LINK_SHIFT); | |
882 | else if (priv->ieee80211->iw_mode == IW_MODE_MASTER) | |
883 | msr |= (MSR_LINK_MASTER<<MSR_LINK_SHIFT); | |
884 | ||
885 | }else | |
886 | msr |= (MSR_LINK_NONE<<MSR_LINK_SHIFT); | |
887 | ||
888 | write_nic_byte(dev, MSR, msr); | |
889 | } | |
890 | ||
891 | void rtl8192_set_chan(struct net_device *dev,short ch) | |
892 | { | |
893 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
894 | RT_TRACE(COMP_RF, "=====>%s()====ch:%d\n", __FUNCTION__, ch); | |
895 | priv->chan=ch; | |
896 | #if 0 | |
897 | if(priv->ieee80211->iw_mode == IW_MODE_ADHOC || | |
898 | priv->ieee80211->iw_mode == IW_MODE_MASTER){ | |
899 | ||
900 | priv->ieee80211->link_state = WLAN_LINK_ASSOCIATED; | |
901 | priv->ieee80211->master_chan = ch; | |
902 | rtl8192_update_beacon_ch(dev); | |
903 | } | |
904 | #endif | |
905 | ||
906 | /* this hack should avoid frame TX during channel setting*/ | |
907 | ||
908 | ||
909 | // tx = read_nic_dword(dev,TX_CONF); | |
910 | // tx &= ~TX_LOOPBACK_MASK; | |
911 | ||
912 | #ifndef LOOP_TEST | |
913 | //TODO | |
914 | // write_nic_dword(dev,TX_CONF, tx |( TX_LOOPBACK_MAC<<TX_LOOPBACK_SHIFT)); | |
915 | ||
916 | //need to implement rf set channel here WB | |
917 | ||
918 | if (priv->rf_set_chan) | |
919 | priv->rf_set_chan(dev,priv->chan); | |
920 | // mdelay(10); | |
921 | // write_nic_dword(dev,TX_CONF,tx | (TX_LOOPBACK_NONE<<TX_LOOPBACK_SHIFT)); | |
922 | #endif | |
923 | } | |
924 | ||
925 | void rtl8192_rx_enable(struct net_device *dev) | |
926 | { | |
927 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
928 | write_nic_dword(dev, RDQDA,priv->rx_ring_dma); | |
929 | } | |
930 | ||
931 | /* the TX_DESC_BASE setting is according to the following queue index | |
932 | * BK_QUEUE ===> 0 | |
933 | * BE_QUEUE ===> 1 | |
934 | * VI_QUEUE ===> 2 | |
935 | * VO_QUEUE ===> 3 | |
936 | * HCCA_QUEUE ===> 4 | |
937 | * TXCMD_QUEUE ===> 5 | |
938 | * MGNT_QUEUE ===> 6 | |
939 | * HIGH_QUEUE ===> 7 | |
940 | * BEACON_QUEUE ===> 8 | |
941 | * */ | |
5e1ad18a | 942 | static u32 TX_DESC_BASE[] = {BKQDA, BEQDA, VIQDA, VOQDA, HCCAQDA, CQDA, MQDA, HQDA, BQDA}; |
ecdfa446 GKH |
943 | void rtl8192_tx_enable(struct net_device *dev) |
944 | { | |
945 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
946 | u32 i; | |
947 | for (i = 0; i < MAX_TX_QUEUE_COUNT; i++) | |
948 | write_nic_dword(dev, TX_DESC_BASE[i], priv->tx_ring[i].dma); | |
949 | ||
950 | ieee80211_reset_queue(priv->ieee80211); | |
951 | } | |
952 | ||
ecdfa446 GKH |
953 | |
954 | static void rtl8192_free_rx_ring(struct net_device *dev) | |
955 | { | |
956 | struct r8192_priv *priv = ieee80211_priv(dev); | |
957 | int i; | |
958 | ||
959 | for (i = 0; i < priv->rxringcount; i++) { | |
960 | struct sk_buff *skb = priv->rx_buf[i]; | |
961 | if (!skb) | |
962 | continue; | |
963 | ||
964 | pci_unmap_single(priv->pdev, | |
965 | *((dma_addr_t *)skb->cb), | |
966 | priv->rxbuffersize, PCI_DMA_FROMDEVICE); | |
967 | kfree_skb(skb); | |
968 | } | |
969 | ||
970 | pci_free_consistent(priv->pdev, sizeof(*priv->rx_ring) * priv->rxringcount, | |
971 | priv->rx_ring, priv->rx_ring_dma); | |
972 | priv->rx_ring = NULL; | |
973 | } | |
974 | ||
975 | static void rtl8192_free_tx_ring(struct net_device *dev, unsigned int prio) | |
976 | { | |
977 | struct r8192_priv *priv = ieee80211_priv(dev); | |
978 | struct rtl8192_tx_ring *ring = &priv->tx_ring[prio]; | |
979 | ||
980 | while (skb_queue_len(&ring->queue)) { | |
981 | tx_desc_819x_pci *entry = &ring->desc[ring->idx]; | |
982 | struct sk_buff *skb = __skb_dequeue(&ring->queue); | |
983 | ||
984 | pci_unmap_single(priv->pdev, le32_to_cpu(entry->TxBuffAddr), | |
985 | skb->len, PCI_DMA_TODEVICE); | |
986 | kfree_skb(skb); | |
987 | ring->idx = (ring->idx + 1) % ring->entries; | |
988 | } | |
989 | ||
990 | pci_free_consistent(priv->pdev, sizeof(*ring->desc)*ring->entries, | |
991 | ring->desc, ring->dma); | |
992 | ring->desc = NULL; | |
993 | } | |
994 | ||
65a43784 | 995 | #if 0 |
5e1ad18a | 996 | static void rtl8192_beacon_disable(struct net_device *dev) |
ecdfa446 GKH |
997 | { |
998 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
999 | u32 reg; | |
1000 | ||
1001 | reg = read_nic_dword(priv->ieee80211->dev,INTA_MASK); | |
1002 | ||
1003 | /* disable Beacon realted interrupt signal */ | |
1004 | reg &= ~(IMR_BcnInt | IMR_BcnInt | IMR_TBDOK | IMR_TBDER); | |
1005 | write_nic_dword(priv->ieee80211->dev, INTA_MASK, reg); | |
1006 | } | |
65a43784 | 1007 | #endif |
1008 | ||
1009 | void PHY_SetRtl8192eRfOff(struct net_device* dev ) | |
1010 | { | |
1011 | //struct r8192_priv *priv = ieee80211_priv(dev); | |
1012 | ||
1013 | //disable RF-Chip A/B | |
1014 | rtl8192_setBBreg(dev, rFPGA0_XA_RFInterfaceOE, BIT4, 0x0); | |
1015 | //analog to digital off, for power save | |
1016 | rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0x300, 0x0); | |
1017 | //digital to analog off, for power save | |
1018 | rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x18, 0x0); | |
1019 | //rx antenna off | |
1020 | rtl8192_setBBreg(dev, rOFDM0_TRxPathEnable, 0xf, 0x0); | |
1021 | //rx antenna off | |
1022 | rtl8192_setBBreg(dev, rOFDM1_TRxPathEnable, 0xf, 0x0); | |
1023 | //analog to digital part2 off, for power save | |
1024 | rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x60, 0x0); | |
1025 | rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x4, 0x0); | |
1026 | // Analog parameter!!Change bias and Lbus control. | |
1027 | write_nic_byte(dev, ANAPAR_FOR_8192PciE, 0x07); | |
1028 | ||
1029 | } | |
ecdfa446 | 1030 | |
65a43784 | 1031 | void rtl8192_halt_adapter(struct net_device *dev, bool reset) |
ecdfa446 | 1032 | { |
65a43784 | 1033 | //u8 cmd; |
ecdfa446 | 1034 | struct r8192_priv *priv = ieee80211_priv(dev); |
65a43784 | 1035 | int i; |
1036 | u8 OpMode; | |
1037 | u8 u1bTmp; | |
1038 | u32 ulRegRead; | |
1039 | ||
1040 | OpMode = RT_OP_MODE_NO_LINK; | |
1041 | priv->ieee80211->SetHwRegHandler(dev, HW_VAR_MEDIA_STATUS, &OpMode); | |
ecdfa446 | 1042 | |
65a43784 | 1043 | #if 1 |
1044 | if(!priv->ieee80211->bSupportRemoteWakeUp) | |
1045 | { | |
1046 | u1bTmp = 0x0; // disable tx/rx. In 8185 we write 0x10 (Reset bit), but here we make reference to WMAC and wirte 0x0. 2006.11.21 Emily | |
1047 | //priv->ieee80211->SetHwRegHandler(dev, HW_VAR_COMMAND, &u1bTmp ); // Using HW_VAR_COMMAND instead of writing CMDR directly. Rewrited by Annie, 2006-04-07. | |
1048 | write_nic_byte(dev, CMDR, u1bTmp); | |
1049 | } | |
1050 | #else | |
ecdfa446 | 1051 | cmd=read_nic_byte(dev,CMDR); |
65a43784 | 1052 | write_nic_byte(dev, CMDR, cmd &~ (CR_TE|CR_RE)); |
1053 | #endif | |
ecdfa446 | 1054 | |
65a43784 | 1055 | mdelay(20); |
ecdfa446 | 1056 | |
65a43784 | 1057 | if(!reset) |
1058 | { | |
1059 | //PlatformStallExecution(150000); | |
1060 | mdelay(150); | |
1061 | ||
1062 | #ifdef RTL8192E | |
1063 | priv->bHwRfOffAction = 2; | |
1064 | #endif | |
1065 | ||
1066 | // | |
1067 | // Call MgntActSet_RF_State instead to prevent RF config race condition. | |
1068 | // By Bruce, 2008-01-17. | |
1069 | // | |
1070 | if(!priv->ieee80211->bSupportRemoteWakeUp) | |
1071 | { | |
1072 | //MgntActSet_RF_State(Adapter, eRfOff, RF_CHANGE_BY_INIT); | |
1073 | //MgntActSet_RF_State(Adapter, eRfOff, Adapter->MgntInfo.RfOffReason); | |
1074 | //if(Adapter->HardwareType == HARDWARE_TYPE_RTL8190P) | |
1075 | ||
1076 | PHY_SetRtl8192eRfOff(dev); | |
1077 | ||
1078 | // 2006.11.30. System reset bit | |
1079 | //priv->ieee80211->GetHwRegHandler(dev, HW_VAR_CPU_RST, (u32*)(&ulRegRead) ); | |
1080 | ulRegRead = read_nic_dword(dev,CPU_GEN); | |
1081 | ulRegRead|=CPU_GEN_SYSTEM_RESET; | |
1082 | //priv->ieee80211->SetHwRegHandler(dev, HW_VAR_CPU_RST, &ulRegRead); | |
1083 | write_nic_dword(dev,CPU_GEN, ulRegRead); | |
1084 | } | |
1085 | else | |
1086 | { | |
1087 | //2008.06.03 for WOL | |
1088 | write_nic_dword(dev, WFCRC0, 0xffffffff); | |
1089 | write_nic_dword(dev, WFCRC1, 0xffffffff); | |
1090 | write_nic_dword(dev, WFCRC2, 0xffffffff); | |
1091 | ||
1092 | //Write PMR register | |
1093 | write_nic_byte(dev, PMR, 0x5); | |
1094 | //Disable tx, enanble rx | |
1095 | write_nic_byte(dev, MacBlkCtrl, 0xa); | |
1096 | } | |
1097 | } | |
1098 | ||
1099 | for(i = 0; i < MAX_QUEUE_SIZE; i++) { | |
1100 | skb_queue_purge(&priv->ieee80211->skb_waitQ [i]); | |
1101 | } | |
1102 | for(i = 0; i < MAX_QUEUE_SIZE; i++) { | |
1103 | skb_queue_purge(&priv->ieee80211->skb_aggQ [i]); | |
1104 | } | |
ecdfa446 GKH |
1105 | |
1106 | skb_queue_purge(&priv->skb_queue); | |
1107 | return; | |
1108 | } | |
1109 | ||
65a43784 | 1110 | #if 0 |
5e1ad18a | 1111 | static void rtl8192_reset(struct net_device *dev) |
ecdfa446 GKH |
1112 | { |
1113 | rtl8192_irq_disable(dev); | |
1114 | printk("This is RTL819xP Reset procedure\n"); | |
1115 | } | |
65a43784 | 1116 | #endif |
ecdfa446 GKH |
1117 | |
1118 | static u16 rtl_rate[] = {10,20,55,110,60,90,120,180,240,360,480,540}; | |
1119 | inline u16 rtl8192_rate2rate(short rate) | |
1120 | { | |
1121 | if (rate >11) return 0; | |
1122 | return rtl_rate[rate]; | |
1123 | } | |
1124 | ||
1125 | ||
1126 | ||
ecdfa446 | 1127 | |
5e1ad18a | 1128 | static void rtl8192_data_hard_stop(struct net_device *dev) |
ecdfa446 GKH |
1129 | { |
1130 | //FIXME !! | |
1131 | #if 0 | |
1132 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
1133 | priv->dma_poll_mask |= (1<<TX_DMA_STOP_LOWPRIORITY_SHIFT); | |
1134 | rtl8192_set_mode(dev,EPROM_CMD_CONFIG); | |
1135 | write_nic_byte(dev,TX_DMA_POLLING,priv->dma_poll_mask); | |
1136 | rtl8192_set_mode(dev,EPROM_CMD_NORMAL); | |
1137 | #endif | |
1138 | } | |
1139 | ||
1140 | ||
5e1ad18a | 1141 | static void rtl8192_data_hard_resume(struct net_device *dev) |
ecdfa446 GKH |
1142 | { |
1143 | // FIXME !! | |
1144 | #if 0 | |
1145 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
1146 | priv->dma_poll_mask &= ~(1<<TX_DMA_STOP_LOWPRIORITY_SHIFT); | |
1147 | rtl8192_set_mode(dev,EPROM_CMD_CONFIG); | |
1148 | write_nic_byte(dev,TX_DMA_POLLING,priv->dma_poll_mask); | |
1149 | rtl8192_set_mode(dev,EPROM_CMD_NORMAL); | |
1150 | #endif | |
1151 | } | |
1152 | ||
1153 | /* this function TX data frames when the ieee80211 stack requires this. | |
1154 | * It checks also if we need to stop the ieee tx queue, eventually do it | |
1155 | */ | |
5e1ad18a | 1156 | static void rtl8192_hard_data_xmit(struct sk_buff *skb, struct net_device *dev, int rate) |
ecdfa446 GKH |
1157 | { |
1158 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
1159 | int ret; | |
1160 | //unsigned long flags; | |
1161 | cb_desc *tcb_desc = (cb_desc *)(skb->cb + MAX_DEV_ADDR_SIZE); | |
1162 | u8 queue_index = tcb_desc->queue_index; | |
1163 | /* shall not be referred by command packet */ | |
1164 | assert(queue_index != TXCMD_QUEUE); | |
1165 | ||
65a43784 | 1166 | if((priv->bHwRadioOff == true)||(!priv->up)) |
1167 | { | |
1168 | kfree_skb(skb); | |
1169 | return; | |
1170 | } | |
1171 | ||
ecdfa446 GKH |
1172 | //spin_lock_irqsave(&priv->tx_lock,flags); |
1173 | ||
1174 | memcpy((unsigned char *)(skb->cb),&dev,sizeof(dev)); | |
1175 | #if 0 | |
1176 | tcb_desc->RATRIndex = 7; | |
1177 | tcb_desc->bTxDisableRateFallBack = 1; | |
1178 | tcb_desc->bTxUseDriverAssingedRate = 1; | |
1179 | tcb_desc->bTxEnableFwCalcDur = 1; | |
1180 | #endif | |
1181 | skb_push(skb, priv->ieee80211->tx_headroom); | |
1182 | ret = rtl8192_tx(dev, skb); | |
1183 | if(ret != 0) { | |
1184 | kfree_skb(skb); | |
1185 | }; | |
1186 | ||
1187 | // | |
1188 | if(queue_index!=MGNT_QUEUE) { | |
1189 | priv->ieee80211->stats.tx_bytes+=(skb->len - priv->ieee80211->tx_headroom); | |
1190 | priv->ieee80211->stats.tx_packets++; | |
1191 | } | |
1192 | ||
1193 | //spin_unlock_irqrestore(&priv->tx_lock,flags); | |
1194 | ||
1195 | // return ret; | |
1196 | return; | |
1197 | } | |
1198 | ||
1199 | /* This is a rough attempt to TX a frame | |
1200 | * This is called by the ieee 80211 stack to TX management frames. | |
1201 | * If the ring is full packet are dropped (for data frame the queue | |
1202 | * is stopped before this can happen). | |
1203 | */ | |
5e1ad18a | 1204 | static int rtl8192_hard_start_xmit(struct sk_buff *skb,struct net_device *dev) |
ecdfa446 GKH |
1205 | { |
1206 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
1207 | ||
1208 | ||
1209 | int ret; | |
1210 | //unsigned long flags; | |
1211 | cb_desc *tcb_desc = (cb_desc *)(skb->cb + MAX_DEV_ADDR_SIZE); | |
1212 | u8 queue_index = tcb_desc->queue_index; | |
1213 | ||
65a43784 | 1214 | if(queue_index != TXCMD_QUEUE){ |
1215 | if((priv->bHwRadioOff == true)||(!priv->up)) | |
1216 | { | |
1217 | kfree_skb(skb); | |
1218 | return 0; | |
1219 | } | |
1220 | } | |
ecdfa446 GKH |
1221 | |
1222 | //spin_lock_irqsave(&priv->tx_lock,flags); | |
1223 | ||
1224 | memcpy((unsigned char *)(skb->cb),&dev,sizeof(dev)); | |
1225 | if(queue_index == TXCMD_QUEUE) { | |
1226 | // skb_push(skb, USB_HWDESC_HEADER_LEN); | |
1227 | rtl819xE_tx_cmd(dev, skb); | |
1228 | ret = 0; | |
1229 | //spin_unlock_irqrestore(&priv->tx_lock,flags); | |
1230 | return ret; | |
1231 | } else { | |
1232 | // RT_TRACE(COMP_SEND, "To send management packet\n"); | |
1233 | tcb_desc->RATRIndex = 7; | |
1234 | tcb_desc->bTxDisableRateFallBack = 1; | |
1235 | tcb_desc->bTxUseDriverAssingedRate = 1; | |
1236 | tcb_desc->bTxEnableFwCalcDur = 1; | |
1237 | skb_push(skb, priv->ieee80211->tx_headroom); | |
1238 | ret = rtl8192_tx(dev, skb); | |
1239 | if(ret != 0) { | |
1240 | kfree_skb(skb); | |
1241 | }; | |
1242 | } | |
1243 | ||
1244 | // priv->ieee80211->stats.tx_bytes+=skb->len; | |
1245 | // priv->ieee80211->stats.tx_packets++; | |
1246 | ||
1247 | //spin_unlock_irqrestore(&priv->tx_lock,flags); | |
1248 | ||
1249 | return ret; | |
1250 | ||
1251 | } | |
1252 | ||
1253 | ||
1254 | void rtl8192_try_wake_queue(struct net_device *dev, int pri); | |
1255 | ||
5e1ad18a | 1256 | static void rtl8192_tx_isr(struct net_device *dev, int prio) |
ecdfa446 GKH |
1257 | { |
1258 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
1259 | ||
1260 | struct rtl8192_tx_ring *ring = &priv->tx_ring[prio]; | |
1261 | ||
1262 | while (skb_queue_len(&ring->queue)) { | |
1263 | tx_desc_819x_pci *entry = &ring->desc[ring->idx]; | |
1264 | struct sk_buff *skb; | |
1265 | ||
bbc9a991 | 1266 | /* beacon packet will only use the first descriptor defaultly, |
ecdfa446 GKH |
1267 | * and the OWN may not be cleared by the hardware |
1268 | * */ | |
1269 | if(prio != BEACON_QUEUE) { | |
1270 | if(entry->OWN) | |
1271 | return; | |
1272 | ring->idx = (ring->idx + 1) % ring->entries; | |
1273 | } | |
1274 | ||
1275 | skb = __skb_dequeue(&ring->queue); | |
1276 | pci_unmap_single(priv->pdev, le32_to_cpu(entry->TxBuffAddr), | |
1277 | skb->len, PCI_DMA_TODEVICE); | |
1278 | ||
1279 | kfree_skb(skb); | |
1280 | } | |
1281 | if (prio == MGNT_QUEUE){ | |
1282 | if (priv->ieee80211->ack_tx_to_ieee){ | |
1283 | if (rtl8192_is_tx_queue_empty(dev)){ | |
1284 | priv->ieee80211->ack_tx_to_ieee = 0; | |
1285 | ieee80211_ps_tx_ack(priv->ieee80211, 1); | |
1286 | } | |
1287 | } | |
1288 | } | |
1289 | ||
1290 | if(prio != BEACON_QUEUE) { | |
1291 | /* try to deal with the pending packets */ | |
1292 | tasklet_schedule(&priv->irq_tx_tasklet); | |
1293 | } | |
1294 | ||
1295 | } | |
1296 | ||
5e1ad18a | 1297 | static void rtl8192_stop_beacon(struct net_device *dev) |
ecdfa446 GKH |
1298 | { |
1299 | //rtl8192_beacon_disable(dev); | |
1300 | } | |
1301 | ||
5e1ad18a | 1302 | static void rtl8192_config_rate(struct net_device* dev, u16* rate_config) |
ecdfa446 GKH |
1303 | { |
1304 | struct r8192_priv *priv = ieee80211_priv(dev); | |
1305 | struct ieee80211_network *net; | |
1306 | u8 i=0, basic_rate = 0; | |
1307 | net = & priv->ieee80211->current_network; | |
1308 | ||
1309 | for (i=0; i<net->rates_len; i++) | |
1310 | { | |
1311 | basic_rate = net->rates[i]&0x7f; | |
1312 | switch(basic_rate) | |
1313 | { | |
1314 | case MGN_1M: *rate_config |= RRSR_1M; break; | |
1315 | case MGN_2M: *rate_config |= RRSR_2M; break; | |
1316 | case MGN_5_5M: *rate_config |= RRSR_5_5M; break; | |
1317 | case MGN_11M: *rate_config |= RRSR_11M; break; | |
1318 | case MGN_6M: *rate_config |= RRSR_6M; break; | |
1319 | case MGN_9M: *rate_config |= RRSR_9M; break; | |
1320 | case MGN_12M: *rate_config |= RRSR_12M; break; | |
1321 | case MGN_18M: *rate_config |= RRSR_18M; break; | |
1322 | case MGN_24M: *rate_config |= RRSR_24M; break; | |
1323 | case MGN_36M: *rate_config |= RRSR_36M; break; | |
1324 | case MGN_48M: *rate_config |= RRSR_48M; break; | |
1325 | case MGN_54M: *rate_config |= RRSR_54M; break; | |
1326 | } | |
1327 | } | |
1328 | for (i=0; i<net->rates_ex_len; i++) | |
1329 | { | |
1330 | basic_rate = net->rates_ex[i]&0x7f; | |
1331 | switch(basic_rate) | |
1332 | { | |
1333 | case MGN_1M: *rate_config |= RRSR_1M; break; | |
1334 | case MGN_2M: *rate_config |= RRSR_2M; break; | |
1335 | case MGN_5_5M: *rate_config |= RRSR_5_5M; break; | |
1336 | case MGN_11M: *rate_config |= RRSR_11M; break; | |
1337 | case MGN_6M: *rate_config |= RRSR_6M; break; | |
1338 | case MGN_9M: *rate_config |= RRSR_9M; break; | |
1339 | case MGN_12M: *rate_config |= RRSR_12M; break; | |
1340 | case MGN_18M: *rate_config |= RRSR_18M; break; | |
1341 | case MGN_24M: *rate_config |= RRSR_24M; break; | |
1342 | case MGN_36M: *rate_config |= RRSR_36M; break; | |
1343 | case MGN_48M: *rate_config |= RRSR_48M; break; | |
1344 | case MGN_54M: *rate_config |= RRSR_54M; break; | |
1345 | } | |
1346 | } | |
1347 | } | |
1348 | ||
1349 | ||
1350 | #define SHORT_SLOT_TIME 9 | |
1351 | #define NON_SHORT_SLOT_TIME 20 | |
1352 | ||
5e1ad18a | 1353 | static void rtl8192_update_cap(struct net_device* dev, u16 cap) |
ecdfa446 GKH |
1354 | { |
1355 | u32 tmp = 0; | |
1356 | struct r8192_priv *priv = ieee80211_priv(dev); | |
1357 | struct ieee80211_network *net = &priv->ieee80211->current_network; | |
1358 | priv->short_preamble = cap & WLAN_CAPABILITY_SHORT_PREAMBLE; | |
1359 | tmp = priv->basic_rate; | |
1360 | if (priv->short_preamble) | |
1361 | tmp |= BRSR_AckShortPmb; | |
1362 | write_nic_dword(dev, RRSR, tmp); | |
1363 | ||
1364 | if (net->mode & (IEEE_G|IEEE_N_24G)) | |
1365 | { | |
1366 | u8 slot_time = 0; | |
1367 | if ((cap & WLAN_CAPABILITY_SHORT_SLOT)&&(!priv->ieee80211->pHTInfo->bCurrentRT2RTLongSlotTime)) | |
1368 | {//short slot time | |
1369 | slot_time = SHORT_SLOT_TIME; | |
1370 | } | |
1371 | else //long slot time | |
1372 | slot_time = NON_SHORT_SLOT_TIME; | |
1373 | priv->slot_time = slot_time; | |
1374 | write_nic_byte(dev, SLOT_TIME, slot_time); | |
1375 | } | |
1376 | ||
1377 | } | |
5e1ad18a GKH |
1378 | |
1379 | static void rtl8192_net_update(struct net_device *dev) | |
ecdfa446 GKH |
1380 | { |
1381 | ||
1382 | struct r8192_priv *priv = ieee80211_priv(dev); | |
1383 | struct ieee80211_network *net; | |
1384 | u16 BcnTimeCfg = 0, BcnCW = 6, BcnIFS = 0xf; | |
1385 | u16 rate_config = 0; | |
1386 | net = &priv->ieee80211->current_network; | |
1387 | //update Basic rate: RR, BRSR | |
1388 | rtl8192_config_rate(dev, &rate_config); | |
1389 | // 2007.01.16, by Emily | |
1390 | // Select RRSR (in Legacy-OFDM and CCK) | |
1391 | // For 8190, we select only 24M, 12M, 6M, 11M, 5.5M, 2M, and 1M from the Basic rate. | |
1392 | // We do not use other rates. | |
1393 | priv->basic_rate = rate_config &= 0x15f; | |
1394 | //BSSID | |
1395 | write_nic_dword(dev,BSSIDR,((u32*)net->bssid)[0]); | |
1396 | write_nic_word(dev,BSSIDR+4,((u16*)net->bssid)[2]); | |
1397 | #if 0 | |
1398 | //MSR | |
1399 | rtl8192_update_msr(dev); | |
1400 | #endif | |
1401 | ||
1402 | ||
1403 | // rtl8192_update_cap(dev, net->capability); | |
1404 | if (priv->ieee80211->iw_mode == IW_MODE_ADHOC) | |
1405 | { | |
1406 | write_nic_word(dev, ATIMWND, 2); | |
1407 | write_nic_word(dev, BCN_DMATIME, 256); | |
1408 | write_nic_word(dev, BCN_INTERVAL, net->beacon_interval); | |
1409 | // write_nic_word(dev, BcnIntTime, 100); | |
1410 | //BIT15 of BCN_DRV_EARLY_INT will indicate whether software beacon or hw beacon is applied. | |
1411 | write_nic_word(dev, BCN_DRV_EARLY_INT, 10); | |
1412 | write_nic_byte(dev, BCN_ERR_THRESH, 100); | |
1413 | ||
1414 | BcnTimeCfg |= (BcnCW<<BCN_TCFG_CW_SHIFT); | |
1415 | // TODO: BcnIFS may required to be changed on ASIC | |
1416 | BcnTimeCfg |= BcnIFS<<BCN_TCFG_IFS; | |
1417 | ||
1418 | write_nic_word(dev, BCN_TCFG, BcnTimeCfg); | |
1419 | } | |
1420 | ||
1421 | ||
1422 | } | |
1423 | ||
ecdfa446 GKH |
1424 | void rtl819xE_tx_cmd(struct net_device *dev, struct sk_buff *skb) |
1425 | { | |
1426 | struct r8192_priv *priv = ieee80211_priv(dev); | |
1427 | struct rtl8192_tx_ring *ring; | |
1428 | tx_desc_819x_pci *entry; | |
1429 | unsigned int idx; | |
1430 | dma_addr_t mapping; | |
1431 | cb_desc *tcb_desc; | |
1432 | unsigned long flags; | |
1433 | ||
1434 | ring = &priv->tx_ring[TXCMD_QUEUE]; | |
1435 | mapping = pci_map_single(priv->pdev, skb->data, skb->len, PCI_DMA_TODEVICE); | |
1436 | ||
1437 | spin_lock_irqsave(&priv->irq_th_lock,flags); | |
1438 | idx = (ring->idx + skb_queue_len(&ring->queue)) % ring->entries; | |
1439 | entry = &ring->desc[idx]; | |
1440 | ||
1441 | tcb_desc = (cb_desc *)(skb->cb + MAX_DEV_ADDR_SIZE); | |
1442 | memset(entry,0,12); | |
1443 | entry->LINIP = tcb_desc->bLastIniPkt; | |
1444 | entry->FirstSeg = 1;//first segment | |
1445 | entry->LastSeg = 1; //last segment | |
1446 | if(tcb_desc->bCmdOrInit == DESC_PACKET_TYPE_INIT) { | |
1447 | entry->CmdInit = DESC_PACKET_TYPE_INIT; | |
1448 | } else { | |
1449 | entry->CmdInit = DESC_PACKET_TYPE_NORMAL; | |
1450 | entry->Offset = sizeof(TX_FWINFO_8190PCI) + 8; | |
1451 | entry->PktSize = (u16)(tcb_desc->pkt_size + entry->Offset); | |
1452 | entry->QueueSelect = QSLT_CMD; | |
1453 | entry->TxFWInfoSize = 0x08; | |
1454 | entry->RATid = (u8)DESC_PACKET_TYPE_INIT; | |
1455 | } | |
1456 | entry->TxBufferSize = skb->len; | |
1457 | entry->TxBuffAddr = cpu_to_le32(mapping); | |
1458 | entry->OWN = 1; | |
1459 | ||
1460 | #ifdef JOHN_DUMP_TXDESC | |
1461 | { int i; | |
1462 | tx_desc_819x_pci *entry1 = &ring->desc[0]; | |
1463 | unsigned int *ptr= (unsigned int *)entry1; | |
1464 | printk("<Tx descriptor>:\n"); | |
1465 | for (i = 0; i < 8; i++) | |
1466 | printk("%8x ", ptr[i]); | |
1467 | printk("\n"); | |
1468 | } | |
1469 | #endif | |
1470 | __skb_queue_tail(&ring->queue, skb); | |
1471 | spin_unlock_irqrestore(&priv->irq_th_lock,flags); | |
1472 | ||
1473 | write_nic_byte(dev, TPPoll, TPPoll_CQ); | |
1474 | ||
1475 | return; | |
1476 | } | |
1477 | ||
1478 | /* | |
1479 | * Mapping Software/Hardware descriptor queue id to "Queue Select Field" | |
1480 | * in TxFwInfo data structure | |
1481 | * 2006.10.30 by Emily | |
1482 | * | |
1483 | * \param QUEUEID Software Queue | |
1484 | */ | |
5e1ad18a | 1485 | static u8 MapHwQueueToFirmwareQueue(u8 QueueID) |
ecdfa446 GKH |
1486 | { |
1487 | u8 QueueSelect = 0x0; //defualt set to | |
1488 | ||
1489 | switch(QueueID) { | |
1490 | case BE_QUEUE: | |
1491 | QueueSelect = QSLT_BE; //or QSelect = pTcb->priority; | |
1492 | break; | |
1493 | ||
1494 | case BK_QUEUE: | |
1495 | QueueSelect = QSLT_BK; //or QSelect = pTcb->priority; | |
1496 | break; | |
1497 | ||
1498 | case VO_QUEUE: | |
1499 | QueueSelect = QSLT_VO; //or QSelect = pTcb->priority; | |
1500 | break; | |
1501 | ||
1502 | case VI_QUEUE: | |
1503 | QueueSelect = QSLT_VI; //or QSelect = pTcb->priority; | |
1504 | break; | |
1505 | case MGNT_QUEUE: | |
1506 | QueueSelect = QSLT_MGNT; | |
1507 | break; | |
1508 | ||
1509 | case BEACON_QUEUE: | |
1510 | QueueSelect = QSLT_BEACON; | |
1511 | break; | |
1512 | ||
1513 | // TODO: 2006.10.30 mark other queue selection until we verify it is OK | |
1514 | // TODO: Remove Assertions | |
1515 | //#if (RTL819X_FPGA_VER & RTL819X_FPGA_GUANGAN_070502) | |
1516 | case TXCMD_QUEUE: | |
1517 | QueueSelect = QSLT_CMD; | |
1518 | break; | |
1519 | //#endif | |
1520 | case HIGH_QUEUE: | |
1521 | //QueueSelect = QSLT_HIGH; | |
1522 | //break; | |
1523 | ||
1524 | default: | |
1525 | RT_TRACE(COMP_ERR, "TransmitTCB(): Impossible Queue Selection: %d \n", QueueID); | |
1526 | break; | |
1527 | } | |
1528 | return QueueSelect; | |
1529 | } | |
1530 | ||
5e1ad18a | 1531 | static u8 MRateToHwRate8190Pci(u8 rate) |
ecdfa446 GKH |
1532 | { |
1533 | u8 ret = DESC90_RATE1M; | |
1534 | ||
1535 | switch(rate) { | |
1536 | case MGN_1M: ret = DESC90_RATE1M; break; | |
1537 | case MGN_2M: ret = DESC90_RATE2M; break; | |
1538 | case MGN_5_5M: ret = DESC90_RATE5_5M; break; | |
1539 | case MGN_11M: ret = DESC90_RATE11M; break; | |
1540 | case MGN_6M: ret = DESC90_RATE6M; break; | |
1541 | case MGN_9M: ret = DESC90_RATE9M; break; | |
1542 | case MGN_12M: ret = DESC90_RATE12M; break; | |
1543 | case MGN_18M: ret = DESC90_RATE18M; break; | |
1544 | case MGN_24M: ret = DESC90_RATE24M; break; | |
1545 | case MGN_36M: ret = DESC90_RATE36M; break; | |
1546 | case MGN_48M: ret = DESC90_RATE48M; break; | |
1547 | case MGN_54M: ret = DESC90_RATE54M; break; | |
1548 | ||
1549 | // HT rate since here | |
1550 | case MGN_MCS0: ret = DESC90_RATEMCS0; break; | |
1551 | case MGN_MCS1: ret = DESC90_RATEMCS1; break; | |
1552 | case MGN_MCS2: ret = DESC90_RATEMCS2; break; | |
1553 | case MGN_MCS3: ret = DESC90_RATEMCS3; break; | |
1554 | case MGN_MCS4: ret = DESC90_RATEMCS4; break; | |
1555 | case MGN_MCS5: ret = DESC90_RATEMCS5; break; | |
1556 | case MGN_MCS6: ret = DESC90_RATEMCS6; break; | |
1557 | case MGN_MCS7: ret = DESC90_RATEMCS7; break; | |
1558 | case MGN_MCS8: ret = DESC90_RATEMCS8; break; | |
1559 | case MGN_MCS9: ret = DESC90_RATEMCS9; break; | |
1560 | case MGN_MCS10: ret = DESC90_RATEMCS10; break; | |
1561 | case MGN_MCS11: ret = DESC90_RATEMCS11; break; | |
1562 | case MGN_MCS12: ret = DESC90_RATEMCS12; break; | |
1563 | case MGN_MCS13: ret = DESC90_RATEMCS13; break; | |
1564 | case MGN_MCS14: ret = DESC90_RATEMCS14; break; | |
1565 | case MGN_MCS15: ret = DESC90_RATEMCS15; break; | |
1566 | case (0x80|0x20): ret = DESC90_RATEMCS32; break; | |
1567 | ||
1568 | default: break; | |
1569 | } | |
1570 | return ret; | |
1571 | } | |
1572 | ||
1573 | ||
5e1ad18a | 1574 | static u8 QueryIsShort(u8 TxHT, u8 TxRate, cb_desc *tcb_desc) |
ecdfa446 GKH |
1575 | { |
1576 | u8 tmp_Short; | |
1577 | ||
1578 | tmp_Short = (TxHT==1)?((tcb_desc->bUseShortGI)?1:0):((tcb_desc->bUseShortPreamble)?1:0); | |
1579 | ||
1580 | if(TxHT==1 && TxRate != DESC90_RATEMCS15) | |
1581 | tmp_Short = 0; | |
1582 | ||
1583 | return tmp_Short; | |
1584 | } | |
1585 | ||
1586 | /* | |
1587 | * The tx procedure is just as following, | |
1588 | * skb->cb will contain all the following information, | |
1589 | * priority, morefrag, rate, &dev. | |
1590 | * */ | |
1591 | short rtl8192_tx(struct net_device *dev, struct sk_buff* skb) | |
1592 | { | |
1593 | struct r8192_priv *priv = ieee80211_priv(dev); | |
1594 | struct rtl8192_tx_ring *ring; | |
1595 | unsigned long flags; | |
1596 | cb_desc *tcb_desc = (cb_desc *)(skb->cb + MAX_DEV_ADDR_SIZE); | |
1597 | tx_desc_819x_pci *pdesc = NULL; | |
1598 | TX_FWINFO_8190PCI *pTxFwInfo = NULL; | |
1599 | dma_addr_t mapping; | |
1600 | bool multi_addr=false,broad_addr=false,uni_addr=false; | |
1601 | u8* pda_addr = NULL; | |
1602 | int idx; | |
1603 | ||
65a43784 | 1604 | if(priv->bdisable_nic){ |
1605 | RT_TRACE(COMP_ERR,"%s: ERR!! Nic is disabled! Can't tx packet len=%d qidx=%d!!!\n", __FUNCTION__, skb->len, tcb_desc->queue_index); | |
1606 | return skb->len; | |
1607 | } | |
1608 | ||
1609 | #ifdef ENABLE_LPS | |
1610 | priv->ieee80211->bAwakePktSent = true; | |
1611 | #endif | |
1612 | ||
ecdfa446 GKH |
1613 | mapping = pci_map_single(priv->pdev, skb->data, skb->len, PCI_DMA_TODEVICE); |
1614 | /* collect the tx packets statitcs */ | |
1615 | pda_addr = ((u8*)skb->data) + sizeof(TX_FWINFO_8190PCI); | |
1616 | if(is_multicast_ether_addr(pda_addr)) | |
1617 | multi_addr = true; | |
1618 | else if(is_broadcast_ether_addr(pda_addr)) | |
1619 | broad_addr = true; | |
1620 | else | |
1621 | uni_addr = true; | |
1622 | ||
1623 | if(uni_addr) | |
1624 | priv->stats.txbytesunicast += (u8)(skb->len) - sizeof(TX_FWINFO_8190PCI); | |
1625 | else if(multi_addr) | |
1626 | priv->stats.txbytesmulticast +=(u8)(skb->len) - sizeof(TX_FWINFO_8190PCI); | |
1627 | else | |
1628 | priv->stats.txbytesbroadcast += (u8)(skb->len) - sizeof(TX_FWINFO_8190PCI); | |
1629 | ||
1630 | /* fill tx firmware */ | |
1631 | pTxFwInfo = (PTX_FWINFO_8190PCI)skb->data; | |
1632 | memset(pTxFwInfo,0,sizeof(TX_FWINFO_8190PCI)); | |
1633 | pTxFwInfo->TxHT = (tcb_desc->data_rate&0x80)?1:0; | |
1634 | pTxFwInfo->TxRate = MRateToHwRate8190Pci((u8)tcb_desc->data_rate); | |
1635 | pTxFwInfo->EnableCPUDur = tcb_desc->bTxEnableFwCalcDur; | |
1636 | pTxFwInfo->Short = QueryIsShort(pTxFwInfo->TxHT, pTxFwInfo->TxRate, tcb_desc); | |
1637 | ||
1638 | /* Aggregation related */ | |
1639 | if(tcb_desc->bAMPDUEnable) { | |
1640 | pTxFwInfo->AllowAggregation = 1; | |
1641 | pTxFwInfo->RxMF = tcb_desc->ampdu_factor; | |
1642 | pTxFwInfo->RxAMD = tcb_desc->ampdu_density; | |
1643 | } else { | |
1644 | pTxFwInfo->AllowAggregation = 0; | |
1645 | pTxFwInfo->RxMF = 0; | |
1646 | pTxFwInfo->RxAMD = 0; | |
1647 | } | |
1648 | ||
1649 | // | |
1650 | // Protection mode related | |
1651 | // | |
1652 | pTxFwInfo->RtsEnable = (tcb_desc->bRTSEnable)?1:0; | |
1653 | pTxFwInfo->CtsEnable = (tcb_desc->bCTSEnable)?1:0; | |
1654 | pTxFwInfo->RtsSTBC = (tcb_desc->bRTSSTBC)?1:0; | |
1655 | pTxFwInfo->RtsHT= (tcb_desc->rts_rate&0x80)?1:0; | |
1656 | pTxFwInfo->RtsRate = MRateToHwRate8190Pci((u8)tcb_desc->rts_rate); | |
1657 | pTxFwInfo->RtsBandwidth = 0; | |
1658 | pTxFwInfo->RtsSubcarrier = tcb_desc->RTSSC; | |
1659 | pTxFwInfo->RtsShort = (pTxFwInfo->RtsHT==0)?(tcb_desc->bRTSUseShortPreamble?1:0):(tcb_desc->bRTSUseShortGI?1:0); | |
1660 | // | |
1661 | // Set Bandwidth and sub-channel settings. | |
1662 | // | |
1663 | if(priv->CurrentChannelBW == HT_CHANNEL_WIDTH_20_40) | |
1664 | { | |
1665 | if(tcb_desc->bPacketBW) | |
1666 | { | |
1667 | pTxFwInfo->TxBandwidth = 1; | |
1668 | #ifdef RTL8190P | |
1669 | pTxFwInfo->TxSubCarrier = 3; | |
1670 | #else | |
1671 | pTxFwInfo->TxSubCarrier = 0; //By SD3's Jerry suggestion, use duplicated mode, cosa 04012008 | |
1672 | #endif | |
1673 | } | |
1674 | else | |
1675 | { | |
1676 | pTxFwInfo->TxBandwidth = 0; | |
1677 | pTxFwInfo->TxSubCarrier = priv->nCur40MhzPrimeSC; | |
1678 | } | |
1679 | } else { | |
1680 | pTxFwInfo->TxBandwidth = 0; | |
1681 | pTxFwInfo->TxSubCarrier = 0; | |
1682 | } | |
1683 | ||
1684 | if (0) | |
1685 | { | |
1686 | /* 2007/07/25 MH Copy current TX FW info.*/ | |
1687 | memcpy((void*)(&Tmp_TxFwInfo), (void*)(pTxFwInfo), sizeof(TX_FWINFO_8190PCI)); | |
1688 | printk("&&&&&&&&&&&&&&&&&&&&&&====>print out fwinf\n"); | |
1689 | printk("===>enable fwcacl:%d\n", Tmp_TxFwInfo.EnableCPUDur); | |
1690 | printk("===>RTS STBC:%d\n", Tmp_TxFwInfo.RtsSTBC); | |
1691 | printk("===>RTS Subcarrier:%d\n", Tmp_TxFwInfo.RtsSubcarrier); | |
1692 | printk("===>Allow Aggregation:%d\n", Tmp_TxFwInfo.AllowAggregation); | |
1693 | printk("===>TX HT bit:%d\n", Tmp_TxFwInfo.TxHT); | |
1694 | printk("===>Tx rate:%d\n", Tmp_TxFwInfo.TxRate); | |
1695 | printk("===>Received AMPDU Density:%d\n", Tmp_TxFwInfo.RxAMD); | |
1696 | printk("===>Received MPDU Factor:%d\n", Tmp_TxFwInfo.RxMF); | |
1697 | printk("===>TxBandwidth:%d\n", Tmp_TxFwInfo.TxBandwidth); | |
1698 | printk("===>TxSubCarrier:%d\n", Tmp_TxFwInfo.TxSubCarrier); | |
1699 | ||
1700 | printk("<=====**********************out of print\n"); | |
1701 | ||
1702 | } | |
1703 | spin_lock_irqsave(&priv->irq_th_lock,flags); | |
1704 | ring = &priv->tx_ring[tcb_desc->queue_index]; | |
1705 | if (tcb_desc->queue_index != BEACON_QUEUE) { | |
1706 | idx = (ring->idx + skb_queue_len(&ring->queue)) % ring->entries; | |
1707 | } else { | |
1708 | idx = 0; | |
1709 | } | |
1710 | ||
1711 | pdesc = &ring->desc[idx]; | |
1712 | if((pdesc->OWN == 1) && (tcb_desc->queue_index != BEACON_QUEUE)) { | |
1713 | RT_TRACE(COMP_ERR,"No more TX desc@%d, ring->idx = %d,idx = %d,%x", \ | |
1714 | tcb_desc->queue_index,ring->idx, idx,skb->len); | |
65a43784 | 1715 | spin_unlock_irqrestore(&priv->irq_th_lock,flags); |
ecdfa446 GKH |
1716 | return skb->len; |
1717 | } | |
1718 | ||
1719 | /* fill tx descriptor */ | |
1720 | memset((u8*)pdesc,0,12); | |
1721 | /*DWORD 0*/ | |
1722 | pdesc->LINIP = 0; | |
1723 | pdesc->CmdInit = 1; | |
1724 | pdesc->Offset = sizeof(TX_FWINFO_8190PCI) + 8; //We must add 8!! Emily | |
1725 | pdesc->PktSize = (u16)skb->len-sizeof(TX_FWINFO_8190PCI); | |
1726 | ||
1727 | /*DWORD 1*/ | |
1728 | pdesc->SecCAMID= 0; | |
1729 | pdesc->RATid = tcb_desc->RATRIndex; | |
1730 | ||
1731 | ||
1732 | pdesc->NoEnc = 1; | |
1733 | pdesc->SecType = 0x0; | |
1734 | if (tcb_desc->bHwSec) { | |
1735 | static u8 tmp =0; | |
1736 | if (!tmp) { | |
1737 | printk("==>================hw sec\n"); | |
1738 | tmp = 1; | |
1739 | } | |
1740 | switch (priv->ieee80211->pairwise_key_type) { | |
1741 | case KEY_TYPE_WEP40: | |
1742 | case KEY_TYPE_WEP104: | |
1743 | pdesc->SecType = 0x1; | |
1744 | pdesc->NoEnc = 0; | |
1745 | break; | |
1746 | case KEY_TYPE_TKIP: | |
1747 | pdesc->SecType = 0x2; | |
1748 | pdesc->NoEnc = 0; | |
1749 | break; | |
1750 | case KEY_TYPE_CCMP: | |
1751 | pdesc->SecType = 0x3; | |
1752 | pdesc->NoEnc = 0; | |
1753 | break; | |
1754 | case KEY_TYPE_NA: | |
1755 | pdesc->SecType = 0x0; | |
1756 | pdesc->NoEnc = 1; | |
1757 | break; | |
1758 | } | |
1759 | } | |
1760 | ||
1761 | // | |
1762 | // Set Packet ID | |
1763 | // | |
1764 | pdesc->PktId = 0x0; | |
1765 | ||
1766 | pdesc->QueueSelect = MapHwQueueToFirmwareQueue(tcb_desc->queue_index); | |
1767 | pdesc->TxFWInfoSize = sizeof(TX_FWINFO_8190PCI); | |
1768 | ||
1769 | pdesc->DISFB = tcb_desc->bTxDisableRateFallBack; | |
1770 | pdesc->USERATE = tcb_desc->bTxUseDriverAssingedRate; | |
1771 | ||
1772 | pdesc->FirstSeg =1; | |
1773 | pdesc->LastSeg = 1; | |
1774 | pdesc->TxBufferSize = skb->len; | |
1775 | ||
1776 | pdesc->TxBuffAddr = cpu_to_le32(mapping); | |
1777 | __skb_queue_tail(&ring->queue, skb); | |
1778 | pdesc->OWN = 1; | |
1779 | spin_unlock_irqrestore(&priv->irq_th_lock,flags); | |
1780 | dev->trans_start = jiffies; | |
1781 | write_nic_word(dev,TPPoll,0x01<<tcb_desc->queue_index); | |
1782 | return 0; | |
1783 | } | |
1784 | ||
5e1ad18a | 1785 | static short rtl8192_alloc_rx_desc_ring(struct net_device *dev) |
ecdfa446 GKH |
1786 | { |
1787 | struct r8192_priv *priv = ieee80211_priv(dev); | |
1788 | rx_desc_819x_pci *entry = NULL; | |
1789 | int i; | |
1790 | ||
1791 | priv->rx_ring = pci_alloc_consistent(priv->pdev, | |
1792 | sizeof(*priv->rx_ring) * priv->rxringcount, &priv->rx_ring_dma); | |
1793 | ||
1794 | if (!priv->rx_ring || (unsigned long)priv->rx_ring & 0xFF) { | |
1795 | RT_TRACE(COMP_ERR,"Cannot allocate RX ring\n"); | |
1796 | return -ENOMEM; | |
1797 | } | |
1798 | ||
1799 | memset(priv->rx_ring, 0, sizeof(*priv->rx_ring) * priv->rxringcount); | |
1800 | priv->rx_idx = 0; | |
1801 | ||
1802 | for (i = 0; i < priv->rxringcount; i++) { | |
1803 | struct sk_buff *skb = dev_alloc_skb(priv->rxbuffersize); | |
1804 | dma_addr_t *mapping; | |
1805 | entry = &priv->rx_ring[i]; | |
1806 | if (!skb) | |
1807 | return 0; | |
1808 | priv->rx_buf[i] = skb; | |
1809 | mapping = (dma_addr_t *)skb->cb; | |
1810 | *mapping = pci_map_single(priv->pdev, skb->tail,//skb_tail_pointer(skb), | |
1811 | priv->rxbuffersize, PCI_DMA_FROMDEVICE); | |
1812 | ||
1813 | entry->BufferAddress = cpu_to_le32(*mapping); | |
1814 | ||
1815 | entry->Length = priv->rxbuffersize; | |
1816 | entry->OWN = 1; | |
1817 | } | |
1818 | ||
1819 | entry->EOR = 1; | |
1820 | return 0; | |
1821 | } | |
1822 | ||
1823 | static int rtl8192_alloc_tx_desc_ring(struct net_device *dev, | |
1824 | unsigned int prio, unsigned int entries) | |
1825 | { | |
1826 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
1827 | tx_desc_819x_pci *ring; | |
1828 | dma_addr_t dma; | |
1829 | int i; | |
1830 | ||
1831 | ring = pci_alloc_consistent(priv->pdev, sizeof(*ring) * entries, &dma); | |
1832 | if (!ring || (unsigned long)ring & 0xFF) { | |
1833 | RT_TRACE(COMP_ERR, "Cannot allocate TX ring (prio = %d)\n", prio); | |
1834 | return -ENOMEM; | |
1835 | } | |
1836 | ||
1837 | memset(ring, 0, sizeof(*ring)*entries); | |
1838 | priv->tx_ring[prio].desc = ring; | |
1839 | priv->tx_ring[prio].dma = dma; | |
1840 | priv->tx_ring[prio].idx = 0; | |
1841 | priv->tx_ring[prio].entries = entries; | |
1842 | skb_queue_head_init(&priv->tx_ring[prio].queue); | |
1843 | ||
1844 | for (i = 0; i < entries; i++) | |
1845 | ring[i].NextDescAddress = | |
1846 | cpu_to_le32((u32)dma + ((i + 1) % entries) * sizeof(*ring)); | |
1847 | ||
1848 | return 0; | |
1849 | } | |
1850 | ||
1851 | ||
5e1ad18a | 1852 | static short rtl8192_pci_initdescring(struct net_device *dev) |
ecdfa446 GKH |
1853 | { |
1854 | u32 ret; | |
1855 | int i; | |
1856 | struct r8192_priv *priv = ieee80211_priv(dev); | |
1857 | ||
1858 | ret = rtl8192_alloc_rx_desc_ring(dev); | |
1859 | if (ret) { | |
1860 | return ret; | |
1861 | } | |
1862 | ||
1863 | ||
1864 | /* general process for other queue */ | |
1865 | for (i = 0; i < MAX_TX_QUEUE_COUNT; i++) { | |
1866 | if ((ret = rtl8192_alloc_tx_desc_ring(dev, i, priv->txringcount))) | |
1867 | goto err_free_rings; | |
1868 | } | |
1869 | ||
1870 | #if 0 | |
1871 | /* specific process for hardware beacon process */ | |
1872 | if ((ret = rtl8192_alloc_tx_desc_ring(dev, MAX_TX_QUEUE_COUNT - 1, 2))) | |
1873 | goto err_free_rings; | |
1874 | #endif | |
1875 | ||
1876 | return 0; | |
1877 | ||
1878 | err_free_rings: | |
1879 | rtl8192_free_rx_ring(dev); | |
1880 | for (i = 0; i < MAX_TX_QUEUE_COUNT; i++) | |
1881 | if (priv->tx_ring[i].desc) | |
1882 | rtl8192_free_tx_ring(dev, i); | |
1883 | return 1; | |
1884 | } | |
1885 | ||
5e1ad18a | 1886 | static void rtl8192_pci_resetdescring(struct net_device *dev) |
ecdfa446 GKH |
1887 | { |
1888 | struct r8192_priv *priv = ieee80211_priv(dev); | |
1889 | int i; | |
1890 | ||
1891 | /* force the rx_idx to the first one */ | |
1892 | if(priv->rx_ring) { | |
1893 | rx_desc_819x_pci *entry = NULL; | |
1894 | for (i = 0; i < priv->rxringcount; i++) { | |
1895 | entry = &priv->rx_ring[i]; | |
1896 | entry->OWN = 1; | |
1897 | } | |
1898 | priv->rx_idx = 0; | |
1899 | } | |
1900 | ||
1901 | /* after reset, release previous pending packet, and force the | |
1902 | * tx idx to the first one */ | |
1903 | for (i = 0; i < MAX_TX_QUEUE_COUNT; i++) { | |
1904 | if (priv->tx_ring[i].desc) { | |
1905 | struct rtl8192_tx_ring *ring = &priv->tx_ring[i]; | |
1906 | ||
1907 | while (skb_queue_len(&ring->queue)) { | |
1908 | tx_desc_819x_pci *entry = &ring->desc[ring->idx]; | |
1909 | struct sk_buff *skb = __skb_dequeue(&ring->queue); | |
1910 | ||
1911 | pci_unmap_single(priv->pdev, le32_to_cpu(entry->TxBuffAddr), | |
1912 | skb->len, PCI_DMA_TODEVICE); | |
1913 | kfree_skb(skb); | |
1914 | ring->idx = (ring->idx + 1) % ring->entries; | |
1915 | } | |
1916 | ring->idx = 0; | |
1917 | } | |
1918 | } | |
1919 | } | |
1920 | ||
1921 | #if 1 | |
1922 | extern void rtl8192_update_ratr_table(struct net_device* dev); | |
5e1ad18a | 1923 | static void rtl8192_link_change(struct net_device *dev) |
ecdfa446 GKH |
1924 | { |
1925 | // int i; | |
1926 | ||
1927 | struct r8192_priv *priv = ieee80211_priv(dev); | |
1928 | struct ieee80211_device* ieee = priv->ieee80211; | |
1929 | //write_nic_word(dev, BCN_INTR_ITV, net->beacon_interval); | |
1930 | if (ieee->state == IEEE80211_LINKED) | |
1931 | { | |
1932 | rtl8192_net_update(dev); | |
1933 | rtl8192_update_ratr_table(dev); | |
1934 | #if 1 | |
1935 | //add this as in pure N mode, wep encryption will use software way, but there is no chance to set this as wep will not set group key in wext. WB.2008.07.08 | |
1936 | if ((KEY_TYPE_WEP40 == ieee->pairwise_key_type) || (KEY_TYPE_WEP104 == ieee->pairwise_key_type)) | |
1937 | EnableHWSecurityConfig8192(dev); | |
1938 | #endif | |
1939 | } | |
1940 | else | |
1941 | { | |
1942 | write_nic_byte(dev, 0x173, 0); | |
1943 | } | |
1944 | /*update timing params*/ | |
1945 | //rtl8192_set_chan(dev, priv->chan); | |
1946 | //MSR | |
1947 | rtl8192_update_msr(dev); | |
1948 | ||
1949 | // 2007/10/16 MH MAC Will update TSF according to all received beacon, so we have | |
1950 | // // To set CBSSID bit when link with any AP or STA. | |
1951 | if (ieee->iw_mode == IW_MODE_INFRA || ieee->iw_mode == IW_MODE_ADHOC) | |
1952 | { | |
1953 | u32 reg = 0; | |
1954 | reg = read_nic_dword(dev, RCR); | |
1955 | if (priv->ieee80211->state == IEEE80211_LINKED) | |
1956 | priv->ReceiveConfig = reg |= RCR_CBSSID; | |
1957 | else | |
1958 | priv->ReceiveConfig = reg &= ~RCR_CBSSID; | |
1959 | write_nic_dword(dev, RCR, reg); | |
1960 | } | |
1961 | } | |
1962 | #endif | |
1963 | ||
1964 | ||
1965 | static struct ieee80211_qos_parameters def_qos_parameters = { | |
1966 | {3,3,3,3},/* cw_min */ | |
1967 | {7,7,7,7},/* cw_max */ | |
1968 | {2,2,2,2},/* aifs */ | |
1969 | {0,0,0,0},/* flags */ | |
1970 | {0,0,0,0} /* tx_op_limit */ | |
1971 | }; | |
1972 | ||
5e1ad18a | 1973 | static void rtl8192_update_beacon(struct work_struct * work) |
ecdfa446 GKH |
1974 | { |
1975 | struct r8192_priv *priv = container_of(work, struct r8192_priv, update_beacon_wq.work); | |
1976 | struct net_device *dev = priv->ieee80211->dev; | |
ecdfa446 GKH |
1977 | struct ieee80211_device* ieee = priv->ieee80211; |
1978 | struct ieee80211_network* net = &ieee->current_network; | |
1979 | ||
1980 | if (ieee->pHTInfo->bCurrentHTSupport) | |
1981 | HTUpdateSelfAndPeerSetting(ieee, net); | |
1982 | ieee->pHTInfo->bCurrentRT2RTLongSlotTime = net->bssht.bdRT2RTLongSlotTime; | |
1983 | rtl8192_update_cap(dev, net->capability); | |
1984 | } | |
1985 | /* | |
1986 | * background support to run QoS activate functionality | |
1987 | */ | |
5e1ad18a | 1988 | static int WDCAPARA_ADD[] = {EDCAPARA_BE,EDCAPARA_BK,EDCAPARA_VI,EDCAPARA_VO}; |
5e1ad18a | 1989 | static void rtl8192_qos_activate(struct work_struct * work) |
ecdfa446 GKH |
1990 | { |
1991 | struct r8192_priv *priv = container_of(work, struct r8192_priv, qos_activate); | |
1992 | struct net_device *dev = priv->ieee80211->dev; | |
ecdfa446 GKH |
1993 | struct ieee80211_qos_parameters *qos_parameters = &priv->ieee80211->current_network.qos_data.parameters; |
1994 | u8 mode = priv->ieee80211->current_network.mode; | |
1995 | // u32 size = sizeof(struct ieee80211_qos_parameters); | |
1996 | u8 u1bAIFS; | |
1997 | u32 u4bAcParam; | |
1998 | int i; | |
ecdfa446 | 1999 | |
ecdfa446 | 2000 | mutex_lock(&priv->mutex); |
ecdfa446 GKH |
2001 | if(priv->ieee80211->state != IEEE80211_LINKED) |
2002 | goto success; | |
2003 | RT_TRACE(COMP_QOS,"qos active process with associate response received\n"); | |
2004 | /* It better set slot time at first */ | |
2005 | /* For we just support b/g mode at present, let the slot time at 9/20 selection */ | |
2006 | /* update the ac parameter to related registers */ | |
2007 | for(i = 0; i < QOS_QUEUE_NUM; i++) { | |
2008 | //Mode G/A: slotTimeTimer = 9; Mode B: 20 | |
2009 | u1bAIFS = qos_parameters->aifs[i] * ((mode&(IEEE_G|IEEE_N_24G)) ?9:20) + aSifsTime; | |
2010 | u4bAcParam = ((((u32)(qos_parameters->tx_op_limit[i]))<< AC_PARAM_TXOP_LIMIT_OFFSET)| | |
2011 | (((u32)(qos_parameters->cw_max[i]))<< AC_PARAM_ECW_MAX_OFFSET)| | |
2012 | (((u32)(qos_parameters->cw_min[i]))<< AC_PARAM_ECW_MIN_OFFSET)| | |
2013 | ((u32)u1bAIFS << AC_PARAM_AIFS_OFFSET)); | |
65a43784 | 2014 | //printk("===>u4bAcParam:%x, ", u4bAcParam); |
ecdfa446 GKH |
2015 | write_nic_dword(dev, WDCAPARA_ADD[i], u4bAcParam); |
2016 | //write_nic_dword(dev, WDCAPARA_ADD[i], 0x005e4332); | |
2017 | } | |
2018 | ||
2019 | success: | |
ecdfa446 | 2020 | mutex_unlock(&priv->mutex); |
ecdfa446 GKH |
2021 | } |
2022 | ||
2023 | static int rtl8192_qos_handle_probe_response(struct r8192_priv *priv, | |
2024 | int active_network, | |
2025 | struct ieee80211_network *network) | |
2026 | { | |
2027 | int ret = 0; | |
2028 | u32 size = sizeof(struct ieee80211_qos_parameters); | |
2029 | ||
2030 | if(priv->ieee80211->state !=IEEE80211_LINKED) | |
2031 | return ret; | |
2032 | ||
2033 | if ((priv->ieee80211->iw_mode != IW_MODE_INFRA)) | |
2034 | return ret; | |
2035 | ||
2036 | if (network->flags & NETWORK_HAS_QOS_MASK) { | |
2037 | if (active_network && | |
2038 | (network->flags & NETWORK_HAS_QOS_PARAMETERS)) | |
2039 | network->qos_data.active = network->qos_data.supported; | |
2040 | ||
2041 | if ((network->qos_data.active == 1) && (active_network == 1) && | |
2042 | (network->flags & NETWORK_HAS_QOS_PARAMETERS) && | |
2043 | (network->qos_data.old_param_count != | |
2044 | network->qos_data.param_count)) { | |
2045 | network->qos_data.old_param_count = | |
2046 | network->qos_data.param_count; | |
ecdfa446 | 2047 | queue_work(priv->priv_wq, &priv->qos_activate); |
ecdfa446 GKH |
2048 | RT_TRACE (COMP_QOS, "QoS parameters change call " |
2049 | "qos_activate\n"); | |
2050 | } | |
2051 | } else { | |
2052 | memcpy(&priv->ieee80211->current_network.qos_data.parameters,\ | |
2053 | &def_qos_parameters, size); | |
2054 | ||
2055 | if ((network->qos_data.active == 1) && (active_network == 1)) { | |
ecdfa446 | 2056 | queue_work(priv->priv_wq, &priv->qos_activate); |
ecdfa446 GKH |
2057 | RT_TRACE(COMP_QOS, "QoS was disabled call qos_activate \n"); |
2058 | } | |
2059 | network->qos_data.active = 0; | |
2060 | network->qos_data.supported = 0; | |
2061 | } | |
2062 | ||
2063 | return 0; | |
2064 | } | |
2065 | ||
2066 | /* handle manage frame frame beacon and probe response */ | |
2067 | static int rtl8192_handle_beacon(struct net_device * dev, | |
2068 | struct ieee80211_beacon * beacon, | |
2069 | struct ieee80211_network * network) | |
2070 | { | |
2071 | struct r8192_priv *priv = ieee80211_priv(dev); | |
2072 | ||
2073 | rtl8192_qos_handle_probe_response(priv,1,network); | |
2074 | ||
ecdfa446 | 2075 | queue_delayed_work(priv->priv_wq, &priv->update_beacon_wq, 0); |
ecdfa446 GKH |
2076 | return 0; |
2077 | ||
2078 | } | |
2079 | ||
2080 | /* | |
2081 | * handling the beaconing responses. if we get different QoS setting | |
2082 | * off the network from the associated setting, adjust the QoS | |
2083 | * setting | |
2084 | */ | |
2085 | static int rtl8192_qos_association_resp(struct r8192_priv *priv, | |
2086 | struct ieee80211_network *network) | |
2087 | { | |
2088 | int ret = 0; | |
2089 | unsigned long flags; | |
2090 | u32 size = sizeof(struct ieee80211_qos_parameters); | |
2091 | int set_qos_param = 0; | |
2092 | ||
2093 | if ((priv == NULL) || (network == NULL)) | |
2094 | return ret; | |
2095 | ||
2096 | if(priv->ieee80211->state !=IEEE80211_LINKED) | |
2097 | return ret; | |
2098 | ||
2099 | if ((priv->ieee80211->iw_mode != IW_MODE_INFRA)) | |
2100 | return ret; | |
2101 | ||
2102 | spin_lock_irqsave(&priv->ieee80211->lock, flags); | |
2103 | if(network->flags & NETWORK_HAS_QOS_PARAMETERS) { | |
2104 | memcpy(&priv->ieee80211->current_network.qos_data.parameters,\ | |
2105 | &network->qos_data.parameters,\ | |
2106 | sizeof(struct ieee80211_qos_parameters)); | |
2107 | priv->ieee80211->current_network.qos_data.active = 1; | |
2108 | #if 0 | |
2109 | if((priv->ieee80211->current_network.qos_data.param_count != \ | |
2110 | network->qos_data.param_count)) | |
2111 | #endif | |
2112 | { | |
2113 | set_qos_param = 1; | |
2114 | /* update qos parameter for current network */ | |
2115 | priv->ieee80211->current_network.qos_data.old_param_count = \ | |
2116 | priv->ieee80211->current_network.qos_data.param_count; | |
2117 | priv->ieee80211->current_network.qos_data.param_count = \ | |
2118 | network->qos_data.param_count; | |
2119 | } | |
2120 | } else { | |
2121 | memcpy(&priv->ieee80211->current_network.qos_data.parameters,\ | |
2122 | &def_qos_parameters, size); | |
2123 | priv->ieee80211->current_network.qos_data.active = 0; | |
2124 | priv->ieee80211->current_network.qos_data.supported = 0; | |
2125 | set_qos_param = 1; | |
2126 | } | |
2127 | ||
2128 | spin_unlock_irqrestore(&priv->ieee80211->lock, flags); | |
2129 | ||
2130 | RT_TRACE(COMP_QOS, "%s: network->flags = %d,%d\n",__FUNCTION__,network->flags ,priv->ieee80211->current_network.qos_data.active); | |
2131 | if (set_qos_param == 1) | |
ecdfa446 | 2132 | queue_work(priv->priv_wq, &priv->qos_activate); |
ecdfa446 GKH |
2133 | |
2134 | return ret; | |
2135 | } | |
2136 | ||
2137 | ||
2138 | static int rtl8192_handle_assoc_response(struct net_device *dev, | |
2139 | struct ieee80211_assoc_response_frame *resp, | |
2140 | struct ieee80211_network *network) | |
2141 | { | |
2142 | struct r8192_priv *priv = ieee80211_priv(dev); | |
2143 | rtl8192_qos_association_resp(priv, network); | |
2144 | return 0; | |
2145 | } | |
2146 | ||
2147 | ||
2148 | //updateRATRTabel for MCS only. Basic rate is not implement. | |
2149 | void rtl8192_update_ratr_table(struct net_device* dev) | |
2150 | // POCTET_STRING posLegacyRate, | |
2151 | // u8* pMcsRate) | |
2152 | // PRT_WLAN_STA pEntry) | |
2153 | { | |
2154 | struct r8192_priv* priv = ieee80211_priv(dev); | |
2155 | struct ieee80211_device* ieee = priv->ieee80211; | |
2156 | u8* pMcsRate = ieee->dot11HTOperationalRateSet; | |
2157 | //struct ieee80211_network *net = &ieee->current_network; | |
2158 | u32 ratr_value = 0; | |
2159 | u8 rate_index = 0; | |
2160 | ||
2161 | rtl8192_config_rate(dev, (u16*)(&ratr_value)); | |
2162 | ratr_value |= (*(u16*)(pMcsRate)) << 12; | |
2163 | // switch (net->mode) | |
2164 | switch (ieee->mode) | |
2165 | { | |
2166 | case IEEE_A: | |
2167 | ratr_value &= 0x00000FF0; | |
2168 | break; | |
2169 | case IEEE_B: | |
2170 | ratr_value &= 0x0000000F; | |
2171 | break; | |
2172 | case IEEE_G: | |
2173 | ratr_value &= 0x00000FF7; | |
2174 | break; | |
2175 | case IEEE_N_24G: | |
2176 | case IEEE_N_5G: | |
2177 | if (ieee->pHTInfo->PeerMimoPs == 0) //MIMO_PS_STATIC | |
2178 | ratr_value &= 0x0007F007; | |
2179 | else{ | |
2180 | if (priv->rf_type == RF_1T2R) | |
2181 | ratr_value &= 0x000FF007; | |
2182 | else | |
2183 | ratr_value &= 0x0F81F007; | |
2184 | } | |
2185 | break; | |
2186 | default: | |
2187 | break; | |
2188 | } | |
2189 | ratr_value &= 0x0FFFFFFF; | |
2190 | if(ieee->pHTInfo->bCurTxBW40MHz && ieee->pHTInfo->bCurShortGI40MHz){ | |
2191 | ratr_value |= 0x80000000; | |
2192 | }else if(!ieee->pHTInfo->bCurTxBW40MHz && ieee->pHTInfo->bCurShortGI20MHz){ | |
2193 | ratr_value |= 0x80000000; | |
2194 | } | |
2195 | write_nic_dword(dev, RATR0+rate_index*4, ratr_value); | |
2196 | write_nic_byte(dev, UFWP, 1); | |
2197 | } | |
2198 | ||
65a43784 | 2199 | #if 0 |
ecdfa446 GKH |
2200 | static u8 ccmp_ie[4] = {0x00,0x50,0xf2,0x04}; |
2201 | static u8 ccmp_rsn_ie[4] = {0x00, 0x0f, 0xac, 0x04}; | |
65a43784 | 2202 | #endif |
2203 | ||
5e1ad18a | 2204 | static bool GetNmodeSupportBySecCfg8190Pci(struct net_device*dev) |
ecdfa446 GKH |
2205 | { |
2206 | #if 1 | |
65a43784 | 2207 | |
2208 | struct r8192_priv *priv = ieee80211_priv(dev); | |
2209 | struct ieee80211_device *ieee = priv->ieee80211; | |
2210 | if (ieee->rtllib_ap_sec_type && | |
2211 | (ieee->rtllib_ap_sec_type(ieee)&(SEC_ALG_WEP|SEC_ALG_TKIP))) { | |
2212 | return false; | |
2213 | } else { | |
2214 | return true; | |
2215 | } | |
2216 | #else | |
ecdfa446 GKH |
2217 | struct r8192_priv* priv = ieee80211_priv(dev); |
2218 | struct ieee80211_device* ieee = priv->ieee80211; | |
2219 | int wpa_ie_len= ieee->wpa_ie_len; | |
2220 | struct ieee80211_crypt_data* crypt; | |
2221 | int encrypt; | |
2222 | ||
2223 | crypt = ieee->crypt[ieee->tx_keyidx]; | |
2224 | encrypt = (ieee->current_network.capability & WLAN_CAPABILITY_PRIVACY) || (ieee->host_encrypt && crypt && crypt->ops && (0 == strcmp(crypt->ops->name,"WEP"))); | |
2225 | ||
2226 | /* simply judge */ | |
2227 | if(encrypt && (wpa_ie_len == 0)) { | |
2228 | /* wep encryption, no N mode setting */ | |
2229 | return false; | |
2230 | // } else if((wpa_ie_len != 0)&&(memcmp(&(ieee->wpa_ie[14]),ccmp_ie,4))) { | |
2231 | } else if((wpa_ie_len != 0)) { | |
2232 | /* parse pairwise key type */ | |
2233 | //if((pairwisekey = WEP40)||(pairwisekey = WEP104)||(pairwisekey = TKIP)) | |
2234 | if (((ieee->wpa_ie[0] == 0xdd) && (!memcmp(&(ieee->wpa_ie[14]),ccmp_ie,4))) || ((ieee->wpa_ie[0] == 0x30) && (!memcmp(&ieee->wpa_ie[10],ccmp_rsn_ie, 4)))) | |
2235 | return true; | |
2236 | else | |
2237 | return false; | |
2238 | } else { | |
2239 | //RT_TRACE(COMP_ERR,"In %s The GroupEncAlgorithm is [4]\n",__FUNCTION__ ); | |
2240 | return true; | |
2241 | } | |
2242 | ||
ecdfa446 GKH |
2243 | return true; |
2244 | #endif | |
2245 | } | |
2246 | ||
5e1ad18a | 2247 | static void rtl8192_refresh_supportrate(struct r8192_priv* priv) |
ecdfa446 GKH |
2248 | { |
2249 | struct ieee80211_device* ieee = priv->ieee80211; | |
2250 | //we donot consider set support rate for ABG mode, only HT MCS rate is set here. | |
2251 | if (ieee->mode == WIRELESS_MODE_N_24G || ieee->mode == WIRELESS_MODE_N_5G) | |
2252 | { | |
2253 | memcpy(ieee->Regdot11HTOperationalRateSet, ieee->RegHTSuppRateSet, 16); | |
2254 | //RT_DEBUG_DATA(COMP_INIT, ieee->RegHTSuppRateSet, 16); | |
2255 | //RT_DEBUG_DATA(COMP_INIT, ieee->Regdot11HTOperationalRateSet, 16); | |
2256 | } | |
2257 | else | |
2258 | memset(ieee->Regdot11HTOperationalRateSet, 0, 16); | |
2259 | return; | |
2260 | } | |
2261 | ||
5e1ad18a | 2262 | static u8 rtl8192_getSupportedWireleeMode(struct net_device*dev) |
ecdfa446 GKH |
2263 | { |
2264 | struct r8192_priv *priv = ieee80211_priv(dev); | |
2265 | u8 ret = 0; | |
2266 | switch(priv->rf_chip) | |
2267 | { | |
2268 | case RF_8225: | |
2269 | case RF_8256: | |
2270 | case RF_PSEUDO_11N: | |
2271 | ret = (WIRELESS_MODE_N_24G|WIRELESS_MODE_G|WIRELESS_MODE_B); | |
2272 | break; | |
2273 | case RF_8258: | |
2274 | ret = (WIRELESS_MODE_A|WIRELESS_MODE_N_5G); | |
2275 | break; | |
2276 | default: | |
2277 | ret = WIRELESS_MODE_B; | |
2278 | break; | |
2279 | } | |
2280 | return ret; | |
2281 | } | |
5e1ad18a GKH |
2282 | |
2283 | static void rtl8192_SetWirelessMode(struct net_device* dev, u8 wireless_mode) | |
ecdfa446 GKH |
2284 | { |
2285 | struct r8192_priv *priv = ieee80211_priv(dev); | |
2286 | u8 bSupportMode = rtl8192_getSupportedWireleeMode(dev); | |
2287 | ||
2288 | #if 1 | |
2289 | if ((wireless_mode == WIRELESS_MODE_AUTO) || ((wireless_mode&bSupportMode)==0)) | |
2290 | { | |
2291 | if(bSupportMode & WIRELESS_MODE_N_24G) | |
2292 | { | |
2293 | wireless_mode = WIRELESS_MODE_N_24G; | |
2294 | } | |
2295 | else if(bSupportMode & WIRELESS_MODE_N_5G) | |
2296 | { | |
2297 | wireless_mode = WIRELESS_MODE_N_5G; | |
2298 | } | |
2299 | else if((bSupportMode & WIRELESS_MODE_A)) | |
2300 | { | |
2301 | wireless_mode = WIRELESS_MODE_A; | |
2302 | } | |
2303 | else if((bSupportMode & WIRELESS_MODE_G)) | |
2304 | { | |
2305 | wireless_mode = WIRELESS_MODE_G; | |
2306 | } | |
2307 | else if((bSupportMode & WIRELESS_MODE_B)) | |
2308 | { | |
2309 | wireless_mode = WIRELESS_MODE_B; | |
2310 | } | |
2311 | else{ | |
2312 | RT_TRACE(COMP_ERR, "%s(), No valid wireless mode supported, SupportedWirelessMode(%x)!!!\n", __FUNCTION__,bSupportMode); | |
2313 | wireless_mode = WIRELESS_MODE_B; | |
2314 | } | |
2315 | } | |
39cfb97b | 2316 | #ifdef TO_DO_LIST //// TODO: this function doesn't work well at this time, we should wait for FPGA |
ecdfa446 GKH |
2317 | ActUpdateChannelAccessSetting( pAdapter, pHalData->CurrentWirelessMode, &pAdapter->MgntInfo.Info8185.ChannelAccessSetting ); |
2318 | #endif | |
2319 | priv->ieee80211->mode = wireless_mode; | |
2320 | ||
2321 | if ((wireless_mode == WIRELESS_MODE_N_24G) || (wireless_mode == WIRELESS_MODE_N_5G)) | |
2322 | priv->ieee80211->pHTInfo->bEnableHT = 1; | |
2323 | else | |
2324 | priv->ieee80211->pHTInfo->bEnableHT = 0; | |
2325 | RT_TRACE(COMP_INIT, "Current Wireless Mode is %x\n", wireless_mode); | |
2326 | rtl8192_refresh_supportrate(priv); | |
2327 | #endif | |
2328 | ||
2329 | } | |
2330 | //init priv variables here | |
2331 | ||
5e1ad18a | 2332 | static bool GetHalfNmodeSupportByAPs819xPci(struct net_device* dev) |
ecdfa446 GKH |
2333 | { |
2334 | bool Reval; | |
2335 | struct r8192_priv* priv = ieee80211_priv(dev); | |
2336 | struct ieee80211_device* ieee = priv->ieee80211; | |
2337 | ||
2338 | if(ieee->bHalfWirelessN24GMode == true) | |
2339 | Reval = true; | |
2340 | else | |
2341 | Reval = false; | |
2342 | ||
2343 | return Reval; | |
2344 | } | |
2345 | ||
2346 | short rtl8192_is_tx_queue_empty(struct net_device *dev) | |
2347 | { | |
2348 | int i=0; | |
2349 | struct r8192_priv *priv = ieee80211_priv(dev); | |
2350 | for (i=0; i<=MGNT_QUEUE; i++) | |
2351 | { | |
2352 | if ((i== TXCMD_QUEUE) || (i == HCCA_QUEUE) ) | |
2353 | continue; | |
2354 | if (skb_queue_len(&(&priv->tx_ring[i])->queue) > 0){ | |
2355 | printk("===>tx queue is not empty:%d, %d\n", i, skb_queue_len(&(&priv->tx_ring[i])->queue)); | |
2356 | return 0; | |
2357 | } | |
2358 | } | |
2359 | return 1; | |
2360 | } | |
5e1ad18a | 2361 | static void rtl8192_hw_sleep_down(struct net_device *dev) |
ecdfa446 | 2362 | { |
65a43784 | 2363 | struct r8192_priv *priv = ieee80211_priv(dev); |
2364 | unsigned long flags = 0; | |
2365 | ||
2366 | spin_lock_irqsave(&priv->rf_ps_lock,flags); | |
2367 | if (priv->RFChangeInProgress) { | |
2368 | spin_unlock_irqrestore(&priv->rf_ps_lock,flags); | |
2369 | RT_TRACE(COMP_RF, "rtl8192_hw_sleep_down(): RF Change in progress! \n"); | |
2370 | printk("rtl8192_hw_sleep_down(): RF Change in progress!\n"); | |
2371 | return; | |
2372 | } | |
2373 | spin_unlock_irqrestore(&priv->rf_ps_lock,flags); | |
2374 | //RT_TRACE(COMP_PS, "%s()============>come to sleep down\n", __FUNCTION__); | |
2375 | ||
ecdfa446 GKH |
2376 | MgntActSet_RF_State(dev, eRfSleep, RF_CHANGE_BY_PS); |
2377 | } | |
5e1ad18a | 2378 | static void rtl8192_hw_sleep_wq (struct work_struct *work) |
ecdfa446 GKH |
2379 | { |
2380 | // struct r8180_priv *priv = container_of(work, struct r8180_priv, watch_dog_wq); | |
2381 | // struct ieee80211_device * ieee = (struct ieee80211_device*) | |
2382 | // container_of(work, struct ieee80211_device, watch_dog_wq); | |
2383 | struct delayed_work *dwork = container_of(work,struct delayed_work,work); | |
2384 | struct ieee80211_device *ieee = container_of(dwork,struct ieee80211_device,hw_sleep_wq); | |
2385 | struct net_device *dev = ieee->dev; | |
65a43784 | 2386 | |
ecdfa446 GKH |
2387 | rtl8192_hw_sleep_down(dev); |
2388 | } | |
65a43784 | 2389 | |
5e1ad18a | 2390 | static void rtl8192_hw_wakeup(struct net_device* dev) |
ecdfa446 | 2391 | { |
65a43784 | 2392 | struct r8192_priv *priv = ieee80211_priv(dev); |
2393 | unsigned long flags = 0; | |
2394 | ||
2395 | spin_lock_irqsave(&priv->rf_ps_lock,flags); | |
2396 | if (priv->RFChangeInProgress) { | |
2397 | spin_unlock_irqrestore(&priv->rf_ps_lock,flags); | |
2398 | RT_TRACE(COMP_RF, "rtl8192_hw_wakeup(): RF Change in progress! \n"); | |
2399 | printk("rtl8192_hw_wakeup(): RF Change in progress! schedule wake up task again\n"); | |
2400 | queue_delayed_work(priv->ieee80211->wq,&priv->ieee80211->hw_wakeup_wq,MSECS(10));//PowerSave is not supported if kernel version is below 2.6.20 | |
2401 | return; | |
2402 | } | |
2403 | spin_unlock_irqrestore(&priv->rf_ps_lock,flags); | |
ecdfa446 | 2404 | |
65a43784 | 2405 | //RT_TRACE(COMP_PS, "%s()============>come to wake up\n", __FUNCTION__); |
ecdfa446 | 2406 | MgntActSet_RF_State(dev, eRfOn, RF_CHANGE_BY_PS); |
ecdfa446 | 2407 | } |
65a43784 | 2408 | |
ecdfa446 GKH |
2409 | void rtl8192_hw_wakeup_wq (struct work_struct *work) |
2410 | { | |
2411 | // struct r8180_priv *priv = container_of(work, struct r8180_priv, watch_dog_wq); | |
2412 | // struct ieee80211_device * ieee = (struct ieee80211_device*) | |
2413 | // container_of(work, struct ieee80211_device, watch_dog_wq); | |
2414 | struct delayed_work *dwork = container_of(work,struct delayed_work,work); | |
2415 | struct ieee80211_device *ieee = container_of(dwork,struct ieee80211_device,hw_wakeup_wq); | |
2416 | struct net_device *dev = ieee->dev; | |
ecdfa446 GKH |
2417 | rtl8192_hw_wakeup(dev); |
2418 | ||
2419 | } | |
2420 | ||
2421 | #define MIN_SLEEP_TIME 50 | |
2422 | #define MAX_SLEEP_TIME 10000 | |
5e1ad18a | 2423 | static void rtl8192_hw_to_sleep(struct net_device *dev, u32 th, u32 tl) |
ecdfa446 | 2424 | { |
ecdfa446 GKH |
2425 | struct r8192_priv *priv = ieee80211_priv(dev); |
2426 | ||
2427 | u32 rb = jiffies; | |
2428 | unsigned long flags; | |
2429 | ||
2430 | spin_lock_irqsave(&priv->ps_lock,flags); | |
2431 | ||
65a43784 | 2432 | // Writing HW register with 0 equals to disable |
2433 | // the timer, that is not really what we want | |
2434 | // | |
2435 | tl -= MSECS(8+16+7); | |
ecdfa446 | 2436 | |
65a43784 | 2437 | // If the interval in witch we are requested to sleep is too |
2438 | // short then give up and remain awake | |
2439 | // when we sleep after send null frame, the timer will be too short to sleep. | |
2440 | // | |
ecdfa446 | 2441 | if(((tl>=rb)&& (tl-rb) <= MSECS(MIN_SLEEP_TIME)) |
65a43784 | 2442 | ||((rb>tl)&& (rb-tl) < MSECS(MIN_SLEEP_TIME))) { |
ecdfa446 | 2443 | spin_unlock_irqrestore(&priv->ps_lock,flags); |
65a43784 | 2444 | printk("too short to sleep::%x, %x, %lx\n",tl, rb, MSECS(MIN_SLEEP_TIME)); |
ecdfa446 GKH |
2445 | return; |
2446 | } | |
2447 | ||
ecdfa446 | 2448 | if(((tl > rb) && ((tl-rb) > MSECS(MAX_SLEEP_TIME)))|| |
65a43784 | 2449 | ((tl < rb) && (tl>MSECS(69)) && ((rb-tl) > MSECS(MAX_SLEEP_TIME)))|| |
2450 | ((tl<rb)&&(tl<MSECS(69))&&((tl+0xffffffff-rb)>MSECS(MAX_SLEEP_TIME)))) { | |
ecdfa446 GKH |
2451 | printk("========>too long to sleep:%x, %x, %lx\n", tl, rb, MSECS(MAX_SLEEP_TIME)); |
2452 | spin_unlock_irqrestore(&priv->ps_lock,flags); | |
2453 | return; | |
2454 | } | |
65a43784 | 2455 | { |
2456 | u32 tmp = (tl>rb)?(tl-rb):(rb-tl); | |
2457 | queue_delayed_work(priv->ieee80211->wq, | |
2458 | &priv->ieee80211->hw_wakeup_wq,tmp); | |
2459 | //PowerSave not supported when kernel version less 2.6.20 | |
2460 | } | |
2461 | queue_delayed_work(priv->ieee80211->wq, | |
2462 | (void *)&priv->ieee80211->hw_sleep_wq,0); | |
ecdfa446 | 2463 | spin_unlock_irqrestore(&priv->ps_lock,flags); |
65a43784 | 2464 | |
ecdfa446 GKH |
2465 | } |
2466 | static void rtl8192_init_priv_variable(struct net_device* dev) | |
2467 | { | |
2468 | struct r8192_priv *priv = ieee80211_priv(dev); | |
2469 | u8 i; | |
65a43784 | 2470 | PRT_POWER_SAVE_CONTROL pPSC = (PRT_POWER_SAVE_CONTROL)(&(priv->ieee80211->PowerSaveControl)); |
2471 | ||
2472 | // Default Halt the NIC if RF is OFF. | |
2473 | pPSC->RegRfPsLevel |= RT_RF_OFF_LEVL_HALT_NIC; | |
2474 | pPSC->RegRfPsLevel |= RT_RF_OFF_LEVL_CLK_REQ; | |
2475 | pPSC->RegRfPsLevel |= RT_RF_OFF_LEVL_ASPM; | |
2476 | pPSC->RegRfPsLevel |= RT_RF_LPS_LEVEL_ASPM; | |
2477 | pPSC->bLeisurePs = true; | |
2478 | pPSC->RegMaxLPSAwakeIntvl = 5; | |
2479 | priv->bHwRadioOff = false; | |
2480 | ||
ecdfa446 GKH |
2481 | priv->being_init_adapter = false; |
2482 | priv->txbuffsize = 1600;//1024; | |
2483 | priv->txfwbuffersize = 4096; | |
2484 | priv->txringcount = 64;//32; | |
2485 | //priv->txbeaconcount = priv->txringcount; | |
2486 | priv->txbeaconcount = 2; | |
2487 | priv->rxbuffersize = 9100;//2048;//1024; | |
2488 | priv->rxringcount = MAX_RX_COUNT;//64; | |
2489 | priv->irq_enabled=0; | |
2490 | priv->card_8192 = NIC_8192E; | |
2491 | priv->rx_skb_complete = 1; | |
2492 | priv->chan = 1; //set to channel 1 | |
2493 | priv->RegWirelessMode = WIRELESS_MODE_AUTO; | |
2494 | priv->RegChannelPlan = 0xf; | |
2495 | priv->nrxAMPDU_size = 0; | |
2496 | priv->nrxAMPDU_aggr_num = 0; | |
2497 | priv->last_rxdesc_tsf_high = 0; | |
2498 | priv->last_rxdesc_tsf_low = 0; | |
2499 | priv->ieee80211->mode = WIRELESS_MODE_AUTO; //SET AUTO | |
2500 | priv->ieee80211->iw_mode = IW_MODE_INFRA; | |
2501 | priv->ieee80211->ieee_up=0; | |
2502 | priv->retry_rts = DEFAULT_RETRY_RTS; | |
2503 | priv->retry_data = DEFAULT_RETRY_DATA; | |
2504 | priv->ieee80211->rts = DEFAULT_RTS_THRESHOLD; | |
2505 | priv->ieee80211->rate = 110; //11 mbps | |
2506 | priv->ieee80211->short_slot = 1; | |
2507 | priv->promisc = (dev->flags & IFF_PROMISC) ? 1:0; | |
2508 | priv->bcck_in_ch14 = false; | |
2509 | priv->bfsync_processing = false; | |
2510 | priv->CCKPresentAttentuation = 0; | |
2511 | priv->rfa_txpowertrackingindex = 0; | |
2512 | priv->rfc_txpowertrackingindex = 0; | |
2513 | priv->CckPwEnl = 6; | |
2514 | priv->ScanDelay = 50;//for Scan TODO | |
2515 | //added by amy for silent reset | |
2516 | priv->ResetProgress = RESET_TYPE_NORESET; | |
2517 | priv->bForcedSilentReset = 0; | |
2518 | priv->bDisableNormalResetCheck = false; | |
2519 | priv->force_reset = false; | |
2520 | //added by amy for power save | |
2521 | priv->RegRfOff = 0; | |
2522 | priv->ieee80211->RfOffReason = 0; | |
2523 | priv->RFChangeInProgress = false; | |
2524 | priv->bHwRfOffAction = 0; | |
2525 | priv->SetRFPowerStateInProgress = false; | |
2526 | priv->ieee80211->PowerSaveControl.bInactivePs = true; | |
2527 | priv->ieee80211->PowerSaveControl.bIPSModeBackup = false; | |
2528 | //just for debug | |
2529 | priv->txpower_checkcnt = 0; | |
2530 | priv->thermal_readback_index =0; | |
2531 | priv->txpower_tracking_callback_cnt = 0; | |
2532 | priv->ccktxpower_adjustcnt_ch14 = 0; | |
2533 | priv->ccktxpower_adjustcnt_not_ch14 = 0; | |
2534 | ||
2535 | priv->ieee80211->current_network.beacon_interval = DEFAULT_BEACONINTERVAL; | |
2536 | priv->ieee80211->iw_mode = IW_MODE_INFRA; | |
2537 | priv->ieee80211->softmac_features = IEEE_SOFTMAC_SCAN | | |
2538 | IEEE_SOFTMAC_ASSOCIATE | IEEE_SOFTMAC_PROBERQ | | |
2539 | IEEE_SOFTMAC_PROBERS | IEEE_SOFTMAC_TX_QUEUE;/* | | |
2540 | IEEE_SOFTMAC_BEACONS;*///added by amy 080604 //| //IEEE_SOFTMAC_SINGLE_QUEUE; | |
2541 | ||
2542 | priv->ieee80211->active_scan = 1; | |
2543 | priv->ieee80211->modulation = IEEE80211_CCK_MODULATION | IEEE80211_OFDM_MODULATION; | |
2544 | priv->ieee80211->host_encrypt = 1; | |
2545 | priv->ieee80211->host_decrypt = 1; | |
2546 | //priv->ieee80211->start_send_beacons = NULL;//rtl819xusb_beacon_tx;//-by amy 080604 | |
2547 | //priv->ieee80211->stop_send_beacons = NULL;//rtl8192_beacon_stop;//-by amy 080604 | |
2548 | priv->ieee80211->start_send_beacons = rtl8192_start_beacon;//+by david 081107 | |
2549 | priv->ieee80211->stop_send_beacons = rtl8192_stop_beacon;//+by david 081107 | |
2550 | priv->ieee80211->softmac_hard_start_xmit = rtl8192_hard_start_xmit; | |
2551 | priv->ieee80211->set_chan = rtl8192_set_chan; | |
2552 | priv->ieee80211->link_change = rtl8192_link_change; | |
2553 | priv->ieee80211->softmac_data_hard_start_xmit = rtl8192_hard_data_xmit; | |
2554 | priv->ieee80211->data_hard_stop = rtl8192_data_hard_stop; | |
2555 | priv->ieee80211->data_hard_resume = rtl8192_data_hard_resume; | |
2556 | priv->ieee80211->init_wmmparam_flag = 0; | |
2557 | priv->ieee80211->fts = DEFAULT_FRAG_THRESHOLD; | |
2558 | priv->ieee80211->check_nic_enough_desc = check_nic_enough_desc; | |
2559 | priv->ieee80211->tx_headroom = sizeof(TX_FWINFO_8190PCI); | |
2560 | priv->ieee80211->qos_support = 1; | |
2561 | priv->ieee80211->dot11PowerSaveMode = 0; | |
2562 | //added by WB | |
2563 | // priv->ieee80211->SwChnlByTimerHandler = rtl8192_phy_SwChnl; | |
2564 | priv->ieee80211->SetBWModeHandler = rtl8192_SetBWMode; | |
2565 | priv->ieee80211->handle_assoc_response = rtl8192_handle_assoc_response; | |
2566 | priv->ieee80211->handle_beacon = rtl8192_handle_beacon; | |
2567 | ||
2568 | priv->ieee80211->sta_wake_up = rtl8192_hw_wakeup; | |
2569 | // priv->ieee80211->ps_request_tx_ack = rtl8192_rq_tx_ack; | |
2570 | priv->ieee80211->enter_sleep_state = rtl8192_hw_to_sleep; | |
2571 | priv->ieee80211->ps_is_queue_empty = rtl8192_is_tx_queue_empty; | |
2572 | //added by david | |
2573 | priv->ieee80211->GetNmodeSupportBySecCfg = GetNmodeSupportBySecCfg8190Pci; | |
2574 | priv->ieee80211->SetWirelessMode = rtl8192_SetWirelessMode; | |
2575 | priv->ieee80211->GetHalfNmodeSupportByAPsHandler = GetHalfNmodeSupportByAPs819xPci; | |
2576 | ||
2577 | //added by amy | |
2578 | priv->ieee80211->InitialGainHandler = InitialGain819xPci; | |
2579 | ||
65a43784 | 2580 | #ifdef ENABLE_IPS |
2581 | priv->ieee80211->ieee80211_ips_leave_wq = ieee80211_ips_leave_wq; | |
2582 | priv->ieee80211->ieee80211_ips_leave = ieee80211_ips_leave; | |
2583 | #endif | |
2584 | #ifdef ENABLE_LPS | |
2585 | priv->ieee80211->LeisurePSLeave = LeisurePSLeave; | |
2586 | #endif//ENABL | |
2587 | ||
2588 | priv->ieee80211->SetHwRegHandler = rtl8192e_SetHwReg; | |
2589 | priv->ieee80211->rtllib_ap_sec_type = rtl8192e_ap_sec_type; | |
2590 | ||
ecdfa446 GKH |
2591 | priv->card_type = USB; |
2592 | { | |
2593 | priv->ShortRetryLimit = 0x30; | |
2594 | priv->LongRetryLimit = 0x30; | |
2595 | } | |
2596 | priv->EarlyRxThreshold = 7; | |
2597 | priv->enable_gpio0 = 0; | |
2598 | ||
2599 | priv->TransmitConfig = 0; | |
2600 | ||
2601 | priv->ReceiveConfig = RCR_ADD3 | | |
2602 | RCR_AMF | RCR_ADF | //accept management/data | |
2603 | RCR_AICV | //accept control frame for SW AP needs PS-poll, 2005.07.07, by rcnjko. | |
2604 | RCR_AB | RCR_AM | RCR_APM | //accept BC/MC/UC | |
2605 | RCR_AAP | ((u32)7<<RCR_MXDMA_OFFSET) | | |
2606 | ((u32)7 << RCR_FIFO_OFFSET) | RCR_ONLYERLPKT; | |
2607 | ||
2608 | priv->irq_mask = (u32)(IMR_ROK | IMR_VODOK | IMR_VIDOK | IMR_BEDOK | IMR_BKDOK |\ | |
2609 | IMR_HCCADOK | IMR_MGNTDOK | IMR_COMDOK | IMR_HIGHDOK |\ | |
2610 | IMR_BDOK | IMR_RXCMDOK | IMR_TIMEOUT0 | IMR_RDU | IMR_RXFOVW |\ | |
2611 | IMR_TXFOVW | IMR_BcnInt | IMR_TBDOK | IMR_TBDER); | |
2612 | ||
2613 | priv->AcmControl = 0; | |
2614 | priv->pFirmware = (rt_firmware*)vmalloc(sizeof(rt_firmware)); | |
2615 | if (priv->pFirmware) | |
2616 | memset(priv->pFirmware, 0, sizeof(rt_firmware)); | |
2617 | ||
2618 | /* rx related queue */ | |
2619 | skb_queue_head_init(&priv->rx_queue); | |
2620 | skb_queue_head_init(&priv->skb_queue); | |
2621 | ||
2622 | /* Tx related queue */ | |
2623 | for(i = 0; i < MAX_QUEUE_SIZE; i++) { | |
2624 | skb_queue_head_init(&priv->ieee80211->skb_waitQ [i]); | |
2625 | } | |
2626 | for(i = 0; i < MAX_QUEUE_SIZE; i++) { | |
2627 | skb_queue_head_init(&priv->ieee80211->skb_aggQ [i]); | |
2628 | } | |
2629 | priv->rf_set_chan = rtl8192_phy_SwChnl; | |
2630 | } | |
2631 | ||
2632 | //init lock here | |
2633 | static void rtl8192_init_priv_lock(struct r8192_priv* priv) | |
2634 | { | |
2635 | spin_lock_init(&priv->tx_lock); | |
2636 | spin_lock_init(&priv->irq_lock);//added by thomas | |
2637 | spin_lock_init(&priv->irq_th_lock); | |
2638 | spin_lock_init(&priv->rf_ps_lock); | |
2639 | spin_lock_init(&priv->ps_lock); | |
2640 | //spin_lock_init(&priv->rf_lock); | |
2641 | sema_init(&priv->wx_sem,1); | |
2642 | sema_init(&priv->rf_sem,1); | |
ecdfa446 | 2643 | mutex_init(&priv->mutex); |
ecdfa446 GKH |
2644 | } |
2645 | ||
ecdfa446 | 2646 | extern void rtl819x_watchdog_wqcallback(struct work_struct *work); |
ecdfa446 GKH |
2647 | |
2648 | void rtl8192_irq_rx_tasklet(struct r8192_priv *priv); | |
2649 | void rtl8192_irq_tx_tasklet(struct r8192_priv *priv); | |
2650 | void rtl8192_prepare_beacon(struct r8192_priv *priv); | |
2651 | //init tasklet and wait_queue here. only 2.6 above kernel is considered | |
2652 | #define DRV_NAME "wlan0" | |
2653 | static void rtl8192_init_priv_task(struct net_device* dev) | |
2654 | { | |
2655 | struct r8192_priv *priv = ieee80211_priv(dev); | |
2656 | ||
ecdfa446 GKH |
2657 | #ifdef PF_SYNCTHREAD |
2658 | priv->priv_wq = create_workqueue(DRV_NAME,0); | |
2659 | #else | |
2660 | priv->priv_wq = create_workqueue(DRV_NAME); | |
2661 | #endif | |
ecdfa446 | 2662 | |
65a43784 | 2663 | #ifdef ENABLE_IPS |
2664 | INIT_WORK(&priv->ieee80211->ips_leave_wq, (void*)IPSLeave_wq); | |
2665 | #endif | |
2666 | ||
ecdfa446 GKH |
2667 | // INIT_WORK(&priv->reset_wq, (void(*)(void*)) rtl8192_restart); |
2668 | INIT_WORK(&priv->reset_wq, rtl8192_restart); | |
2669 | // INIT_DELAYED_WORK(&priv->watch_dog_wq, hal_dm_watchdog); | |
2670 | INIT_DELAYED_WORK(&priv->watch_dog_wq, rtl819x_watchdog_wqcallback); | |
2671 | INIT_DELAYED_WORK(&priv->txpower_tracking_wq, dm_txpower_trackingcallback); | |
2672 | INIT_DELAYED_WORK(&priv->rfpath_check_wq, dm_rf_pathcheck_workitemcallback); | |
2673 | INIT_DELAYED_WORK(&priv->update_beacon_wq, rtl8192_update_beacon); | |
2674 | //INIT_WORK(&priv->SwChnlWorkItem, rtl8192_SwChnl_WorkItem); | |
2675 | //INIT_WORK(&priv->SetBWModeWorkItem, rtl8192_SetBWModeWorkItem); | |
2676 | INIT_WORK(&priv->qos_activate, rtl8192_qos_activate); | |
2677 | INIT_DELAYED_WORK(&priv->ieee80211->hw_wakeup_wq,(void*) rtl8192_hw_wakeup_wq); | |
2678 | INIT_DELAYED_WORK(&priv->ieee80211->hw_sleep_wq,(void*) rtl8192_hw_sleep_wq); | |
2679 | ||
ecdfa446 GKH |
2680 | tasklet_init(&priv->irq_rx_tasklet, |
2681 | (void(*)(unsigned long))rtl8192_irq_rx_tasklet, | |
2682 | (unsigned long)priv); | |
2683 | tasklet_init(&priv->irq_tx_tasklet, | |
2684 | (void(*)(unsigned long))rtl8192_irq_tx_tasklet, | |
2685 | (unsigned long)priv); | |
2686 | tasklet_init(&priv->irq_prepare_beacon_tasklet, | |
2687 | (void(*)(unsigned long))rtl8192_prepare_beacon, | |
2688 | (unsigned long)priv); | |
2689 | } | |
2690 | ||
2691 | static void rtl8192_get_eeprom_size(struct net_device* dev) | |
2692 | { | |
2693 | u16 curCR = 0; | |
2694 | struct r8192_priv *priv = ieee80211_priv(dev); | |
2695 | RT_TRACE(COMP_INIT, "===========>%s()\n", __FUNCTION__); | |
2696 | curCR = read_nic_dword(dev, EPROM_CMD); | |
2697 | RT_TRACE(COMP_INIT, "read from Reg Cmd9346CR(%x):%x\n", EPROM_CMD, curCR); | |
2698 | //whether need I consider BIT5? | |
2699 | priv->epromtype = (curCR & EPROM_CMD_9356SEL) ? EPROM_93c56 : EPROM_93c46; | |
2700 | RT_TRACE(COMP_INIT, "<===========%s(), epromtype:%d\n", __FUNCTION__, priv->epromtype); | |
2701 | } | |
2702 | ||
2703 | //used to swap endian. as ntohl & htonl are not neccessary to swap endian, so use this instead. | |
2704 | static inline u16 endian_swap(u16* data) | |
2705 | { | |
2706 | u16 tmp = *data; | |
2707 | *data = (tmp >> 8) | (tmp << 8); | |
2708 | return *data; | |
2709 | } | |
2710 | ||
2711 | /* | |
2712 | * Note: Adapter->EEPROMAddressSize should be set before this function call. | |
2713 | * EEPROM address size can be got through GetEEPROMSize8185() | |
2714 | */ | |
2715 | static void rtl8192_read_eeprom_info(struct net_device* dev) | |
2716 | { | |
2717 | struct r8192_priv *priv = ieee80211_priv(dev); | |
2718 | ||
2719 | u8 tempval; | |
2720 | #ifdef RTL8192E | |
2721 | u8 ICVer8192, ICVer8256; | |
2722 | #endif | |
2723 | u16 i,usValue, IC_Version; | |
2724 | u16 EEPROMId; | |
2725 | #ifdef RTL8190P | |
2726 | u8 offset;//, tmpAFR; | |
2727 | u8 EepromTxPower[100]; | |
2728 | #endif | |
2729 | u8 bMac_Tmp_Addr[6] = {0x00, 0xe0, 0x4c, 0x00, 0x00, 0x01}; | |
2730 | RT_TRACE(COMP_INIT, "====> rtl8192_read_eeprom_info\n"); | |
2731 | ||
2732 | ||
2733 | // TODO: I don't know if we need to apply EF function to EEPROM read function | |
2734 | ||
2735 | //2 Read EEPROM ID to make sure autoload is success | |
2736 | EEPROMId = eprom_read(dev, 0); | |
2737 | if( EEPROMId != RTL8190_EEPROM_ID ) | |
2738 | { | |
2739 | RT_TRACE(COMP_ERR, "EEPROM ID is invalid:%x, %x\n", EEPROMId, RTL8190_EEPROM_ID); | |
2740 | priv->AutoloadFailFlag=true; | |
2741 | } | |
2742 | else | |
2743 | { | |
2744 | priv->AutoloadFailFlag=false; | |
2745 | } | |
2746 | ||
2747 | // | |
2748 | // Assign Chip Version ID | |
2749 | // | |
2750 | // Read IC Version && Channel Plan | |
2751 | if(!priv->AutoloadFailFlag) | |
2752 | { | |
2753 | // VID, PID | |
2754 | priv->eeprom_vid = eprom_read(dev, (EEPROM_VID >> 1)); | |
2755 | priv->eeprom_did = eprom_read(dev, (EEPROM_DID >> 1)); | |
2756 | ||
2757 | usValue = eprom_read(dev, (u16)(EEPROM_Customer_ID>>1)) >> 8 ; | |
2758 | priv->eeprom_CustomerID = (u8)( usValue & 0xff); | |
2759 | usValue = eprom_read(dev, (EEPROM_ICVersion_ChannelPlan>>1)); | |
2760 | priv->eeprom_ChannelPlan = usValue&0xff; | |
2761 | IC_Version = ((usValue&0xff00)>>8); | |
2762 | ||
2763 | #ifdef RTL8190P | |
2764 | priv->card_8192_version = (VERSION_8190)(IC_Version); | |
2765 | #else | |
2766 | #ifdef RTL8192E | |
2767 | ICVer8192 = (IC_Version&0xf); //bit0~3; 1:A cut, 2:B cut, 3:C cut... | |
2768 | ICVer8256 = ((IC_Version&0xf0)>>4);//bit4~6, bit7 reserved for other RF chip; 1:A cut, 2:B cut, 3:C cut... | |
2769 | RT_TRACE(COMP_INIT, "\nICVer8192 = 0x%x\n", ICVer8192); | |
2770 | RT_TRACE(COMP_INIT, "\nICVer8256 = 0x%x\n", ICVer8256); | |
2771 | if(ICVer8192 == 0x2) //B-cut | |
2772 | { | |
2773 | if(ICVer8256 == 0x5) //E-cut | |
2774 | priv->card_8192_version= VERSION_8190_BE; | |
2775 | } | |
2776 | #endif | |
2777 | #endif | |
2778 | switch(priv->card_8192_version) | |
2779 | { | |
2780 | case VERSION_8190_BD: | |
2781 | case VERSION_8190_BE: | |
2782 | break; | |
2783 | default: | |
2784 | priv->card_8192_version = VERSION_8190_BD; | |
2785 | break; | |
2786 | } | |
2787 | RT_TRACE(COMP_INIT, "\nIC Version = 0x%x\n", priv->card_8192_version); | |
2788 | } | |
2789 | else | |
2790 | { | |
2791 | priv->card_8192_version = VERSION_8190_BD; | |
2792 | priv->eeprom_vid = 0; | |
2793 | priv->eeprom_did = 0; | |
2794 | priv->eeprom_CustomerID = 0; | |
2795 | priv->eeprom_ChannelPlan = 0; | |
2796 | RT_TRACE(COMP_INIT, "\nIC Version = 0x%x\n", 0xff); | |
2797 | } | |
2798 | ||
2799 | RT_TRACE(COMP_INIT, "EEPROM VID = 0x%4x\n", priv->eeprom_vid); | |
2800 | RT_TRACE(COMP_INIT, "EEPROM DID = 0x%4x\n", priv->eeprom_did); | |
2801 | RT_TRACE(COMP_INIT,"EEPROM Customer ID: 0x%2x\n", priv->eeprom_CustomerID); | |
2802 | ||
2803 | //2 Read Permanent MAC address | |
2804 | if(!priv->AutoloadFailFlag) | |
2805 | { | |
2806 | for(i = 0; i < 6; i += 2) | |
2807 | { | |
2808 | usValue = eprom_read(dev, (u16) ((EEPROM_NODE_ADDRESS_BYTE_0+i)>>1)); | |
2809 | *(u16*)(&dev->dev_addr[i]) = usValue; | |
2810 | } | |
2811 | } else { | |
2812 | // when auto load failed, the last address byte set to be a random one. | |
2813 | // added by david woo.2007/11/7 | |
2814 | memcpy(dev->dev_addr, bMac_Tmp_Addr, 6); | |
ecdfa446 GKH |
2815 | } |
2816 | ||
2817 | RT_TRACE(COMP_INIT, "Permanent Address = %02x-%02x-%02x-%02x-%02x-%02x\n", | |
2818 | dev->dev_addr[0], dev->dev_addr[1], | |
2819 | dev->dev_addr[2], dev->dev_addr[3], | |
2820 | dev->dev_addr[4], dev->dev_addr[5]); | |
2821 | ||
2822 | //2 TX Power Check EEPROM Fail or not | |
2823 | if(priv->card_8192_version > VERSION_8190_BD) { | |
2824 | priv->bTXPowerDataReadFromEEPORM = true; | |
2825 | } else { | |
2826 | priv->bTXPowerDataReadFromEEPORM = false; | |
2827 | } | |
2828 | ||
bbc9a991 | 2829 | // 2007/11/15 MH 8190PCI Default=2T4R, 8192PCIE default=1T2R |
ecdfa446 GKH |
2830 | priv->rf_type = RTL819X_DEFAULT_RF_TYPE; |
2831 | ||
2832 | if(priv->card_8192_version > VERSION_8190_BD) | |
2833 | { | |
2834 | // Read RF-indication and Tx Power gain index diff of legacy to HT OFDM rate. | |
2835 | if(!priv->AutoloadFailFlag) | |
2836 | { | |
2837 | tempval = (eprom_read(dev, (EEPROM_RFInd_PowerDiff>>1))) & 0xff; | |
2838 | priv->EEPROMLegacyHTTxPowerDiff = tempval & 0xf; // bit[3:0] | |
2839 | ||
2840 | if (tempval&0x80) //RF-indication, bit[7] | |
2841 | priv->rf_type = RF_1T2R; | |
2842 | else | |
2843 | priv->rf_type = RF_2T4R; | |
2844 | } | |
2845 | else | |
2846 | { | |
2847 | priv->EEPROMLegacyHTTxPowerDiff = EEPROM_Default_LegacyHTTxPowerDiff; | |
2848 | } | |
2849 | RT_TRACE(COMP_INIT, "EEPROMLegacyHTTxPowerDiff = %d\n", | |
2850 | priv->EEPROMLegacyHTTxPowerDiff); | |
2851 | ||
2852 | // Read ThermalMeter from EEPROM | |
2853 | if(!priv->AutoloadFailFlag) | |
2854 | { | |
2855 | priv->EEPROMThermalMeter = (u8)(((eprom_read(dev, (EEPROM_ThermalMeter>>1))) & 0xff00)>>8); | |
2856 | } | |
2857 | else | |
2858 | { | |
2859 | priv->EEPROMThermalMeter = EEPROM_Default_ThermalMeter; | |
2860 | } | |
2861 | RT_TRACE(COMP_INIT, "ThermalMeter = %d\n", priv->EEPROMThermalMeter); | |
2862 | //vivi, for tx power track | |
2863 | priv->TSSI_13dBm = priv->EEPROMThermalMeter *100; | |
2864 | ||
2865 | if(priv->epromtype == EPROM_93c46) | |
2866 | { | |
2867 | // Read antenna tx power offset of B/C/D to A and CrystalCap from EEPROM | |
2868 | if(!priv->AutoloadFailFlag) | |
2869 | { | |
2870 | usValue = eprom_read(dev, (EEPROM_TxPwDiff_CrystalCap>>1)); | |
2871 | priv->EEPROMAntPwDiff = (usValue&0x0fff); | |
2872 | priv->EEPROMCrystalCap = (u8)((usValue&0xf000)>>12); | |
2873 | } | |
2874 | else | |
2875 | { | |
2876 | priv->EEPROMAntPwDiff = EEPROM_Default_AntTxPowerDiff; | |
2877 | priv->EEPROMCrystalCap = EEPROM_Default_TxPwDiff_CrystalCap; | |
2878 | } | |
2879 | RT_TRACE(COMP_INIT, "EEPROMAntPwDiff = %d\n", priv->EEPROMAntPwDiff); | |
2880 | RT_TRACE(COMP_INIT, "EEPROMCrystalCap = %d\n", priv->EEPROMCrystalCap); | |
2881 | ||
2882 | // | |
2883 | // Get per-channel Tx Power Level | |
2884 | // | |
2885 | for(i=0; i<14; i+=2) | |
2886 | { | |
2887 | if(!priv->AutoloadFailFlag) | |
2888 | { | |
2889 | usValue = eprom_read(dev, (u16) ((EEPROM_TxPwIndex_CCK+i)>>1) ); | |
2890 | } | |
2891 | else | |
2892 | { | |
2893 | usValue = EEPROM_Default_TxPower; | |
2894 | } | |
2895 | *((u16*)(&priv->EEPROMTxPowerLevelCCK[i])) = usValue; | |
2896 | RT_TRACE(COMP_INIT,"CCK Tx Power Level, Index %d = 0x%02x\n", i, priv->EEPROMTxPowerLevelCCK[i]); | |
2897 | RT_TRACE(COMP_INIT, "CCK Tx Power Level, Index %d = 0x%02x\n", i+1, priv->EEPROMTxPowerLevelCCK[i+1]); | |
2898 | } | |
2899 | for(i=0; i<14; i+=2) | |
2900 | { | |
2901 | if(!priv->AutoloadFailFlag) | |
2902 | { | |
2903 | usValue = eprom_read(dev, (u16) ((EEPROM_TxPwIndex_OFDM_24G+i)>>1) ); | |
2904 | } | |
2905 | else | |
2906 | { | |
2907 | usValue = EEPROM_Default_TxPower; | |
2908 | } | |
2909 | *((u16*)(&priv->EEPROMTxPowerLevelOFDM24G[i])) = usValue; | |
2910 | RT_TRACE(COMP_INIT, "OFDM 2.4G Tx Power Level, Index %d = 0x%02x\n", i, priv->EEPROMTxPowerLevelOFDM24G[i]); | |
2911 | RT_TRACE(COMP_INIT, "OFDM 2.4G Tx Power Level, Index %d = 0x%02x\n", i+1, priv->EEPROMTxPowerLevelOFDM24G[i+1]); | |
2912 | } | |
2913 | } | |
2914 | else if(priv->epromtype== EPROM_93c56) | |
2915 | { | |
2916 | #ifdef RTL8190P | |
2917 | // Read CrystalCap from EEPROM | |
2918 | if(!priv->AutoloadFailFlag) | |
2919 | { | |
2920 | priv->EEPROMAntPwDiff = EEPROM_Default_AntTxPowerDiff; | |
2921 | priv->EEPROMCrystalCap = (u8)(((eprom_read(dev, (EEPROM_C56_CrystalCap>>1))) & 0xf000)>>12); | |
2922 | } | |
2923 | else | |
2924 | { | |
2925 | priv->EEPROMAntPwDiff = EEPROM_Default_AntTxPowerDiff; | |
2926 | priv->EEPROMCrystalCap = EEPROM_Default_TxPwDiff_CrystalCap; | |
2927 | } | |
2928 | RT_TRACE(COMP_INIT,"EEPROMAntPwDiff = %d\n", priv->EEPROMAntPwDiff); | |
2929 | RT_TRACE(COMP_INIT, "EEPROMCrystalCap = %d\n", priv->EEPROMCrystalCap); | |
2930 | ||
2931 | // Get Tx Power Level by Channel | |
2932 | if(!priv->AutoloadFailFlag) | |
2933 | { | |
2934 | // Read Tx power of Channel 1 ~ 14 from EEPROM. | |
2935 | for(i = 0; i < 12; i+=2) | |
2936 | { | |
2937 | if (i <6) | |
2938 | offset = EEPROM_C56_RfA_CCK_Chnl1_TxPwIndex + i; | |
2939 | else | |
2940 | offset = EEPROM_C56_RfC_CCK_Chnl1_TxPwIndex + i - 6; | |
2941 | usValue = eprom_read(dev, (offset>>1)); | |
2942 | *((u16*)(&EepromTxPower[i])) = usValue; | |
2943 | } | |
2944 | ||
2945 | for(i = 0; i < 12; i++) | |
2946 | { | |
2947 | if (i <= 2) | |
2948 | priv->EEPROMRfACCKChnl1TxPwLevel[i] = EepromTxPower[i]; | |
2949 | else if ((i >=3 )&&(i <= 5)) | |
2950 | priv->EEPROMRfAOfdmChnlTxPwLevel[i-3] = EepromTxPower[i]; | |
2951 | else if ((i >=6 )&&(i <= 8)) | |
2952 | priv->EEPROMRfCCCKChnl1TxPwLevel[i-6] = EepromTxPower[i]; | |
2953 | else | |
2954 | priv->EEPROMRfCOfdmChnlTxPwLevel[i-9] = EepromTxPower[i]; | |
2955 | } | |
2956 | } | |
2957 | else | |
2958 | { | |
2959 | priv->EEPROMRfACCKChnl1TxPwLevel[0] = EEPROM_Default_TxPowerLevel; | |
2960 | priv->EEPROMRfACCKChnl1TxPwLevel[1] = EEPROM_Default_TxPowerLevel; | |
2961 | priv->EEPROMRfACCKChnl1TxPwLevel[2] = EEPROM_Default_TxPowerLevel; | |
2962 | ||
2963 | priv->EEPROMRfAOfdmChnlTxPwLevel[0] = EEPROM_Default_TxPowerLevel; | |
2964 | priv->EEPROMRfAOfdmChnlTxPwLevel[1] = EEPROM_Default_TxPowerLevel; | |
2965 | priv->EEPROMRfAOfdmChnlTxPwLevel[2] = EEPROM_Default_TxPowerLevel; | |
2966 | ||
2967 | priv->EEPROMRfCCCKChnl1TxPwLevel[0] = EEPROM_Default_TxPowerLevel; | |
2968 | priv->EEPROMRfCCCKChnl1TxPwLevel[1] = EEPROM_Default_TxPowerLevel; | |
2969 | priv->EEPROMRfCCCKChnl1TxPwLevel[2] = EEPROM_Default_TxPowerLevel; | |
2970 | ||
2971 | priv->EEPROMRfCOfdmChnlTxPwLevel[0] = EEPROM_Default_TxPowerLevel; | |
2972 | priv->EEPROMRfCOfdmChnlTxPwLevel[1] = EEPROM_Default_TxPowerLevel; | |
2973 | priv->EEPROMRfCOfdmChnlTxPwLevel[2] = EEPROM_Default_TxPowerLevel; | |
2974 | } | |
2975 | RT_TRACE(COMP_INIT, "priv->EEPROMRfACCKChnl1TxPwLevel[0] = 0x%x\n", priv->EEPROMRfACCKChnl1TxPwLevel[0]); | |
2976 | RT_TRACE(COMP_INIT, "priv->EEPROMRfACCKChnl1TxPwLevel[1] = 0x%x\n", priv->EEPROMRfACCKChnl1TxPwLevel[1]); | |
2977 | RT_TRACE(COMP_INIT, "priv->EEPROMRfACCKChnl1TxPwLevel[2] = 0x%x\n", priv->EEPROMRfACCKChnl1TxPwLevel[2]); | |
2978 | RT_TRACE(COMP_INIT, "priv->EEPROMRfAOfdmChnlTxPwLevel[0] = 0x%x\n", priv->EEPROMRfAOfdmChnlTxPwLevel[0]); | |
2979 | RT_TRACE(COMP_INIT, "priv->EEPROMRfAOfdmChnlTxPwLevel[1] = 0x%x\n", priv->EEPROMRfAOfdmChnlTxPwLevel[1]); | |
2980 | RT_TRACE(COMP_INIT, "priv->EEPROMRfAOfdmChnlTxPwLevel[2] = 0x%x\n", priv->EEPROMRfAOfdmChnlTxPwLevel[2]); | |
2981 | RT_TRACE(COMP_INIT, "priv->EEPROMRfCCCKChnl1TxPwLevel[0] = 0x%x\n", priv->EEPROMRfCCCKChnl1TxPwLevel[0]); | |
2982 | RT_TRACE(COMP_INIT, "priv->EEPROMRfCCCKChnl1TxPwLevel[1] = 0x%x\n", priv->EEPROMRfCCCKChnl1TxPwLevel[1]); | |
2983 | RT_TRACE(COMP_INIT, "priv->EEPROMRfCCCKChnl1TxPwLevel[2] = 0x%x\n", priv->EEPROMRfCCCKChnl1TxPwLevel[2]); | |
2984 | RT_TRACE(COMP_INIT, "priv->EEPROMRfCOfdmChnlTxPwLevel[0] = 0x%x\n", priv->EEPROMRfCOfdmChnlTxPwLevel[0]); | |
2985 | RT_TRACE(COMP_INIT, "priv->EEPROMRfCOfdmChnlTxPwLevel[1] = 0x%x\n", priv->EEPROMRfCOfdmChnlTxPwLevel[1]); | |
2986 | RT_TRACE(COMP_INIT, "priv->EEPROMRfCOfdmChnlTxPwLevel[2] = 0x%x\n", priv->EEPROMRfCOfdmChnlTxPwLevel[2]); | |
2987 | #endif | |
2988 | ||
2989 | } | |
2990 | // | |
2991 | // Update HAL variables. | |
2992 | // | |
2993 | if(priv->epromtype == EPROM_93c46) | |
2994 | { | |
2995 | for(i=0; i<14; i++) | |
2996 | { | |
2997 | priv->TxPowerLevelCCK[i] = priv->EEPROMTxPowerLevelCCK[i]; | |
2998 | priv->TxPowerLevelOFDM24G[i] = priv->EEPROMTxPowerLevelOFDM24G[i]; | |
2999 | } | |
3000 | priv->LegacyHTTxPowerDiff = priv->EEPROMLegacyHTTxPowerDiff; | |
3001 | // Antenna B gain offset to antenna A, bit0~3 | |
3002 | priv->AntennaTxPwDiff[0] = (priv->EEPROMAntPwDiff & 0xf); | |
3003 | // Antenna C gain offset to antenna A, bit4~7 | |
3004 | priv->AntennaTxPwDiff[1] = ((priv->EEPROMAntPwDiff & 0xf0)>>4); | |
3005 | // Antenna D gain offset to antenna A, bit8~11 | |
3006 | priv->AntennaTxPwDiff[2] = ((priv->EEPROMAntPwDiff & 0xf00)>>8); | |
3007 | // CrystalCap, bit12~15 | |
3008 | priv->CrystalCap = priv->EEPROMCrystalCap; | |
3009 | // ThermalMeter, bit0~3 for RFIC1, bit4~7 for RFIC2 | |
3010 | priv->ThermalMeter[0] = (priv->EEPROMThermalMeter & 0xf); | |
3011 | priv->ThermalMeter[1] = ((priv->EEPROMThermalMeter & 0xf0)>>4); | |
3012 | } | |
3013 | else if(priv->epromtype == EPROM_93c56) | |
3014 | { | |
3015 | //char cck_pwr_diff_a=0, cck_pwr_diff_c=0; | |
3016 | ||
3017 | //cck_pwr_diff_a = pHalData->EEPROMRfACCKChnl7TxPwLevel - pHalData->EEPROMRfAOfdmChnlTxPwLevel[1]; | |
3018 | //cck_pwr_diff_c = pHalData->EEPROMRfCCCKChnl7TxPwLevel - pHalData->EEPROMRfCOfdmChnlTxPwLevel[1]; | |
3019 | for(i=0; i<3; i++) // channel 1~3 use the same Tx Power Level. | |
3020 | { | |
3021 | priv->TxPowerLevelCCK_A[i] = priv->EEPROMRfACCKChnl1TxPwLevel[0]; | |
3022 | priv->TxPowerLevelOFDM24G_A[i] = priv->EEPROMRfAOfdmChnlTxPwLevel[0]; | |
3023 | priv->TxPowerLevelCCK_C[i] = priv->EEPROMRfCCCKChnl1TxPwLevel[0]; | |
3024 | priv->TxPowerLevelOFDM24G_C[i] = priv->EEPROMRfCOfdmChnlTxPwLevel[0]; | |
3025 | } | |
3026 | for(i=3; i<9; i++) // channel 4~9 use the same Tx Power Level | |
3027 | { | |
3028 | priv->TxPowerLevelCCK_A[i] = priv->EEPROMRfACCKChnl1TxPwLevel[1]; | |
3029 | priv->TxPowerLevelOFDM24G_A[i] = priv->EEPROMRfAOfdmChnlTxPwLevel[1]; | |
3030 | priv->TxPowerLevelCCK_C[i] = priv->EEPROMRfCCCKChnl1TxPwLevel[1]; | |
3031 | priv->TxPowerLevelOFDM24G_C[i] = priv->EEPROMRfCOfdmChnlTxPwLevel[1]; | |
3032 | } | |
3033 | for(i=9; i<14; i++) // channel 10~14 use the same Tx Power Level | |
3034 | { | |
3035 | priv->TxPowerLevelCCK_A[i] = priv->EEPROMRfACCKChnl1TxPwLevel[2]; | |
3036 | priv->TxPowerLevelOFDM24G_A[i] = priv->EEPROMRfAOfdmChnlTxPwLevel[2]; | |
3037 | priv->TxPowerLevelCCK_C[i] = priv->EEPROMRfCCCKChnl1TxPwLevel[2]; | |
3038 | priv->TxPowerLevelOFDM24G_C[i] = priv->EEPROMRfCOfdmChnlTxPwLevel[2]; | |
3039 | } | |
3040 | for(i=0; i<14; i++) | |
3041 | RT_TRACE(COMP_INIT, "priv->TxPowerLevelCCK_A[%d] = 0x%x\n", i, priv->TxPowerLevelCCK_A[i]); | |
3042 | for(i=0; i<14; i++) | |
3043 | RT_TRACE(COMP_INIT,"priv->TxPowerLevelOFDM24G_A[%d] = 0x%x\n", i, priv->TxPowerLevelOFDM24G_A[i]); | |
3044 | for(i=0; i<14; i++) | |
3045 | RT_TRACE(COMP_INIT, "priv->TxPowerLevelCCK_C[%d] = 0x%x\n", i, priv->TxPowerLevelCCK_C[i]); | |
3046 | for(i=0; i<14; i++) | |
3047 | RT_TRACE(COMP_INIT, "priv->TxPowerLevelOFDM24G_C[%d] = 0x%x\n", i, priv->TxPowerLevelOFDM24G_C[i]); | |
3048 | priv->LegacyHTTxPowerDiff = priv->EEPROMLegacyHTTxPowerDiff; | |
3049 | priv->AntennaTxPwDiff[0] = 0; | |
3050 | priv->AntennaTxPwDiff[1] = 0; | |
3051 | priv->AntennaTxPwDiff[2] = 0; | |
3052 | priv->CrystalCap = priv->EEPROMCrystalCap; | |
3053 | // ThermalMeter, bit0~3 for RFIC1, bit4~7 for RFIC2 | |
3054 | priv->ThermalMeter[0] = (priv->EEPROMThermalMeter & 0xf); | |
3055 | priv->ThermalMeter[1] = ((priv->EEPROMThermalMeter & 0xf0)>>4); | |
3056 | } | |
3057 | } | |
3058 | ||
3059 | if(priv->rf_type == RF_1T2R) | |
3060 | { | |
3061 | RT_TRACE(COMP_INIT, "\n1T2R config\n"); | |
3062 | } | |
3063 | else if (priv->rf_type == RF_2T4R) | |
3064 | { | |
3065 | RT_TRACE(COMP_INIT, "\n2T4R config\n"); | |
3066 | } | |
3067 | ||
3068 | // 2008/01/16 MH We can only know RF type in the function. So we have to init | |
3069 | // DIG RATR table again. | |
3070 | init_rate_adaptive(dev); | |
3071 | ||
3072 | //1 Make a copy for following variables and we can change them if we want | |
3073 | ||
3074 | priv->rf_chip= RF_8256; | |
3075 | ||
3076 | if(priv->RegChannelPlan == 0xf) | |
3077 | { | |
3078 | priv->ChannelPlan = priv->eeprom_ChannelPlan; | |
3079 | } | |
3080 | else | |
3081 | { | |
3082 | priv->ChannelPlan = priv->RegChannelPlan; | |
3083 | } | |
3084 | ||
3085 | // | |
3086 | // Used PID and DID to Set CustomerID | |
3087 | // | |
3088 | if( priv->eeprom_vid == 0x1186 && priv->eeprom_did == 0x3304 ) | |
3089 | { | |
3090 | priv->CustomerID = RT_CID_DLINK; | |
3091 | } | |
3092 | ||
3093 | switch(priv->eeprom_CustomerID) | |
3094 | { | |
3095 | case EEPROM_CID_DEFAULT: | |
3096 | priv->CustomerID = RT_CID_DEFAULT; | |
3097 | break; | |
3098 | case EEPROM_CID_CAMEO: | |
3099 | priv->CustomerID = RT_CID_819x_CAMEO; | |
3100 | break; | |
3101 | case EEPROM_CID_RUNTOP: | |
3102 | priv->CustomerID = RT_CID_819x_RUNTOP; | |
3103 | break; | |
3104 | case EEPROM_CID_NetCore: | |
3105 | priv->CustomerID = RT_CID_819x_Netcore; | |
3106 | break; | |
3107 | case EEPROM_CID_TOSHIBA: // Merge by Jacken, 2008/01/31 | |
3108 | priv->CustomerID = RT_CID_TOSHIBA; | |
3109 | if(priv->eeprom_ChannelPlan&0x80) | |
3110 | priv->ChannelPlan = priv->eeprom_ChannelPlan&0x7f; | |
3111 | else | |
3112 | priv->ChannelPlan = 0x0; | |
3113 | RT_TRACE(COMP_INIT, "Toshiba ChannelPlan = 0x%x\n", | |
3114 | priv->ChannelPlan); | |
3115 | break; | |
3116 | case EEPROM_CID_Nettronix: | |
3117 | priv->ScanDelay = 100; //cosa add for scan | |
3118 | priv->CustomerID = RT_CID_Nettronix; | |
3119 | break; | |
3120 | case EEPROM_CID_Pronet: | |
3121 | priv->CustomerID = RT_CID_PRONET; | |
3122 | break; | |
3123 | case EEPROM_CID_DLINK: | |
3124 | priv->CustomerID = RT_CID_DLINK; | |
3125 | break; | |
3126 | ||
3127 | case EEPROM_CID_WHQL: | |
3128 | //Adapter->bInHctTest = TRUE;//do not supported | |
3129 | ||
3130 | //priv->bSupportTurboMode = FALSE; | |
3131 | //priv->bAutoTurboBy8186 = FALSE; | |
3132 | ||
3133 | //pMgntInfo->PowerSaveControl.bInactivePs = FALSE; | |
3134 | //pMgntInfo->PowerSaveControl.bIPSModeBackup = FALSE; | |
3135 | //pMgntInfo->PowerSaveControl.bLeisurePs = FALSE; | |
3136 | ||
3137 | break; | |
3138 | default: | |
3139 | // value from RegCustomerID | |
3140 | break; | |
3141 | } | |
3142 | ||
3143 | //Avoid the channel plan array overflow, by Bruce, 2007-08-27. | |
3144 | if(priv->ChannelPlan > CHANNEL_PLAN_LEN - 1) | |
3145 | priv->ChannelPlan = 0; //FCC | |
3146 | ||
3147 | switch(priv->CustomerID) | |
3148 | { | |
3149 | case RT_CID_DEFAULT: | |
3150 | #ifdef RTL8190P | |
3151 | priv->LedStrategy = HW_LED; | |
3152 | #else | |
3153 | #ifdef RTL8192E | |
3154 | priv->LedStrategy = SW_LED_MODE1; | |
3155 | #endif | |
3156 | #endif | |
3157 | break; | |
3158 | ||
3159 | case RT_CID_819x_CAMEO: | |
3160 | priv->LedStrategy = SW_LED_MODE2; | |
3161 | break; | |
3162 | ||
3163 | case RT_CID_819x_RUNTOP: | |
3164 | priv->LedStrategy = SW_LED_MODE3; | |
3165 | break; | |
3166 | ||
3167 | case RT_CID_819x_Netcore: | |
3168 | priv->LedStrategy = SW_LED_MODE4; | |
3169 | break; | |
3170 | ||
3171 | case RT_CID_Nettronix: | |
3172 | priv->LedStrategy = SW_LED_MODE5; | |
3173 | break; | |
3174 | ||
3175 | case RT_CID_PRONET: | |
3176 | priv->LedStrategy = SW_LED_MODE6; | |
3177 | break; | |
3178 | ||
3179 | case RT_CID_TOSHIBA: //Modify by Jacken 2008/01/31 | |
3180 | // Do nothing. | |
3181 | //break; | |
3182 | ||
3183 | default: | |
3184 | #ifdef RTL8190P | |
3185 | priv->LedStrategy = HW_LED; | |
3186 | #else | |
3187 | #ifdef RTL8192E | |
3188 | priv->LedStrategy = SW_LED_MODE1; | |
3189 | #endif | |
3190 | #endif | |
3191 | break; | |
3192 | } | |
65a43784 | 3193 | |
3194 | ||
ecdfa446 | 3195 | if( priv->eeprom_vid == 0x1186 && priv->eeprom_did == 0x3304) |
65a43784 | 3196 | priv->ieee80211->bSupportRemoteWakeUp = true; |
ecdfa446 | 3197 | else |
65a43784 | 3198 | priv->ieee80211->bSupportRemoteWakeUp = false; |
3199 | ||
3200 | ||
ecdfa446 GKH |
3201 | RT_TRACE(COMP_INIT, "RegChannelPlan(%d)\n", priv->RegChannelPlan); |
3202 | RT_TRACE(COMP_INIT, "ChannelPlan = %d \n", priv->ChannelPlan); | |
3203 | RT_TRACE(COMP_INIT, "LedStrategy = %d \n", priv->LedStrategy); | |
3204 | RT_TRACE(COMP_TRACE, "<==== ReadAdapterInfo\n"); | |
3205 | ||
3206 | return ; | |
3207 | } | |
3208 | ||
3209 | ||
5e1ad18a | 3210 | static short rtl8192_get_channel_map(struct net_device * dev) |
ecdfa446 GKH |
3211 | { |
3212 | struct r8192_priv *priv = ieee80211_priv(dev); | |
3213 | #ifdef ENABLE_DOT11D | |
3214 | if(priv->ChannelPlan> COUNTRY_CODE_GLOBAL_DOMAIN){ | |
3215 | printk("rtl8180_init:Error channel plan! Set to default.\n"); | |
3216 | priv->ChannelPlan= 0; | |
3217 | } | |
3218 | RT_TRACE(COMP_INIT, "Channel plan is %d\n",priv->ChannelPlan); | |
3219 | ||
3220 | rtl819x_set_channel_map(priv->ChannelPlan, priv); | |
3221 | #else | |
3222 | int ch,i; | |
3223 | //Set Default Channel Plan | |
3224 | if(!channels){ | |
3225 | DMESG("No channels, aborting"); | |
3226 | return -1; | |
3227 | } | |
3228 | ch=channels; | |
3229 | priv->ChannelPlan= 0;//hikaru | |
3230 | // set channels 1..14 allowed in given locale | |
3231 | for (i=1; i<=14; i++) { | |
3232 | (priv->ieee80211->channel_map)[i] = (u8)(ch & 0x01); | |
3233 | ch >>= 1; | |
3234 | } | |
3235 | #endif | |
3236 | return 0; | |
3237 | } | |
5e1ad18a GKH |
3238 | |
3239 | static short rtl8192_init(struct net_device *dev) | |
ecdfa446 GKH |
3240 | { |
3241 | struct r8192_priv *priv = ieee80211_priv(dev); | |
3242 | memset(&(priv->stats),0,sizeof(struct Stats)); | |
3243 | rtl8192_init_priv_variable(dev); | |
3244 | rtl8192_init_priv_lock(priv); | |
3245 | rtl8192_init_priv_task(dev); | |
3246 | rtl8192_get_eeprom_size(dev); | |
3247 | rtl8192_read_eeprom_info(dev); | |
3248 | rtl8192_get_channel_map(dev); | |
3249 | init_hal_dm(dev); | |
3250 | init_timer(&priv->watch_dog_timer); | |
3251 | priv->watch_dog_timer.data = (unsigned long)dev; | |
3252 | priv->watch_dog_timer.function = watch_dog_timer_callback; | |
3253 | #if defined(IRQF_SHARED) | |
3254 | if(request_irq(dev->irq, (void*)rtl8192_interrupt, IRQF_SHARED, dev->name, dev)){ | |
3255 | #else | |
3256 | if(request_irq(dev->irq, (void *)rtl8192_interrupt, SA_SHIRQ, dev->name, dev)){ | |
3257 | #endif | |
3258 | printk("Error allocating IRQ %d",dev->irq); | |
3259 | return -1; | |
3260 | }else{ | |
3261 | priv->irq=dev->irq; | |
3262 | printk("IRQ %d",dev->irq); | |
3263 | } | |
3264 | if(rtl8192_pci_initdescring(dev)!=0){ | |
3265 | printk("Endopoints initialization failed"); | |
3266 | return -1; | |
3267 | } | |
3268 | ||
3269 | //rtl8192_rx_enable(dev); | |
3270 | //rtl8192_adapter_start(dev); | |
ecdfa446 GKH |
3271 | return 0; |
3272 | } | |
3273 | ||
3274 | /****************************************************************************** | |
3275 | *function: This function actually only set RRSR, RATR and BW_OPMODE registers | |
3276 | * not to do all the hw config as its name says | |
3277 | * input: net_device dev | |
3278 | * output: none | |
3279 | * return: none | |
3280 | * notice: This part need to modified according to the rate set we filtered | |
3281 | * ****************************************************************************/ | |
5e1ad18a | 3282 | static void rtl8192_hwconfig(struct net_device* dev) |
ecdfa446 GKH |
3283 | { |
3284 | u32 regRATR = 0, regRRSR = 0; | |
3285 | u8 regBwOpMode = 0, regTmp = 0; | |
3286 | struct r8192_priv *priv = ieee80211_priv(dev); | |
3287 | ||
3288 | // Set RRSR, RATR, and BW_OPMODE registers | |
3289 | // | |
3290 | switch(priv->ieee80211->mode) | |
3291 | { | |
3292 | case WIRELESS_MODE_B: | |
3293 | regBwOpMode = BW_OPMODE_20MHZ; | |
3294 | regRATR = RATE_ALL_CCK; | |
3295 | regRRSR = RATE_ALL_CCK; | |
3296 | break; | |
3297 | case WIRELESS_MODE_A: | |
3298 | regBwOpMode = BW_OPMODE_5G |BW_OPMODE_20MHZ; | |
3299 | regRATR = RATE_ALL_OFDM_AG; | |
3300 | regRRSR = RATE_ALL_OFDM_AG; | |
3301 | break; | |
3302 | case WIRELESS_MODE_G: | |
3303 | regBwOpMode = BW_OPMODE_20MHZ; | |
3304 | regRATR = RATE_ALL_CCK | RATE_ALL_OFDM_AG; | |
3305 | regRRSR = RATE_ALL_CCK | RATE_ALL_OFDM_AG; | |
3306 | break; | |
3307 | case WIRELESS_MODE_AUTO: | |
3308 | case WIRELESS_MODE_N_24G: | |
3309 | // It support CCK rate by default. | |
3310 | // CCK rate will be filtered out only when associated AP does not support it. | |
3311 | regBwOpMode = BW_OPMODE_20MHZ; | |
3312 | regRATR = RATE_ALL_CCK | RATE_ALL_OFDM_AG | RATE_ALL_OFDM_1SS | RATE_ALL_OFDM_2SS; | |
3313 | regRRSR = RATE_ALL_CCK | RATE_ALL_OFDM_AG; | |
3314 | break; | |
3315 | case WIRELESS_MODE_N_5G: | |
3316 | regBwOpMode = BW_OPMODE_5G; | |
3317 | regRATR = RATE_ALL_OFDM_AG | RATE_ALL_OFDM_1SS | RATE_ALL_OFDM_2SS; | |
3318 | regRRSR = RATE_ALL_OFDM_AG; | |
3319 | break; | |
3320 | } | |
3321 | ||
3322 | write_nic_byte(dev, BW_OPMODE, regBwOpMode); | |
3323 | { | |
3324 | u32 ratr_value = 0; | |
3325 | ratr_value = regRATR; | |
3326 | if (priv->rf_type == RF_1T2R) | |
3327 | { | |
3328 | ratr_value &= ~(RATE_ALL_OFDM_2SS); | |
3329 | } | |
3330 | write_nic_dword(dev, RATR0, ratr_value); | |
3331 | write_nic_byte(dev, UFWP, 1); | |
3332 | } | |
3333 | regTmp = read_nic_byte(dev, 0x313); | |
3334 | regRRSR = ((regTmp) << 24) | (regRRSR & 0x00ffffff); | |
3335 | write_nic_dword(dev, RRSR, regRRSR); | |
3336 | ||
3337 | // | |
3338 | // Set Retry Limit here | |
3339 | // | |
3340 | write_nic_word(dev, RETRY_LIMIT, | |
3341 | priv->ShortRetryLimit << RETRY_LIMIT_SHORT_SHIFT | \ | |
3342 | priv->LongRetryLimit << RETRY_LIMIT_LONG_SHIFT); | |
3343 | // Set Contention Window here | |
3344 | ||
3345 | // Set Tx AGC | |
3346 | ||
3347 | // Set Tx Antenna including Feedback control | |
3348 | ||
3349 | // Set Auto Rate fallback control | |
3350 | ||
3351 | ||
3352 | } | |
3353 | ||
3354 | ||
5e1ad18a | 3355 | static RT_STATUS rtl8192_adapter_start(struct net_device *dev) |
ecdfa446 GKH |
3356 | { |
3357 | struct r8192_priv *priv = ieee80211_priv(dev); | |
3358 | // struct ieee80211_device *ieee = priv->ieee80211; | |
3359 | u32 ulRegRead; | |
3360 | RT_STATUS rtStatus = RT_STATUS_SUCCESS; | |
3361 | // static char szMACPHYRegFile[] = RTL819X_PHY_MACPHY_REG; | |
3362 | // static char szMACPHYRegPGFile[] = RTL819X_PHY_MACPHY_REG_PG; | |
3363 | //u8 eRFPath; | |
3364 | u8 tmpvalue; | |
3365 | #ifdef RTL8192E | |
3366 | u8 ICVersion,SwitchingRegulatorOutput; | |
3367 | #endif | |
3368 | bool bfirmwareok = true; | |
3369 | #ifdef RTL8190P | |
3370 | u8 ucRegRead; | |
3371 | #endif | |
3372 | u32 tmpRegA, tmpRegC, TempCCk; | |
3373 | int i =0; | |
3374 | // u32 dwRegRead = 0; | |
3375 | ||
3376 | RT_TRACE(COMP_INIT, "====>%s()\n", __FUNCTION__); | |
3377 | priv->being_init_adapter = true; | |
3378 | rtl8192_pci_resetdescring(dev); | |
3379 | // 2007/11/02 MH Before initalizing RF. We can not use FW to do RF-R/W. | |
3380 | priv->Rf_Mode = RF_OP_By_SW_3wire; | |
3381 | #ifdef RTL8192E | |
3382 | //dPLL on | |
3383 | if(priv->ResetProgress == RESET_TYPE_NORESET) | |
3384 | { | |
3385 | write_nic_byte(dev, ANAPAR, 0x37); | |
3386 | // Accordign to designer's explain, LBUS active will never > 10ms. We delay 10ms | |
3387 | // Joseph increae the time to prevent firmware download fail | |
3388 | mdelay(500); | |
3389 | } | |
3390 | #endif | |
3391 | //PlatformSleepUs(10000); | |
3392 | // For any kind of InitializeAdapter process, we shall use system now!! | |
3393 | priv->pFirmware->firmware_status = FW_STATUS_0_INIT; | |
3394 | ||
3395 | // Set to eRfoff in order not to count receive count. | |
3396 | if(priv->RegRfOff == TRUE) | |
3397 | priv->ieee80211->eRFPowerState = eRfOff; | |
3398 | ||
3399 | // | |
3400 | //3 //Config CPUReset Register | |
3401 | //3// | |
3402 | //3 Firmware Reset Or Not | |
3403 | ulRegRead = read_nic_dword(dev, CPU_GEN); | |
3404 | if(priv->pFirmware->firmware_status == FW_STATUS_0_INIT) | |
3405 | { //called from MPInitialized. do nothing | |
3406 | ulRegRead |= CPU_GEN_SYSTEM_RESET; | |
3407 | }else if(priv->pFirmware->firmware_status == FW_STATUS_5_READY) | |
3408 | ulRegRead |= CPU_GEN_FIRMWARE_RESET; // Called from MPReset | |
3409 | else | |
3410 | RT_TRACE(COMP_ERR, "ERROR in %s(): undefined firmware state(%d)\n", __FUNCTION__, priv->pFirmware->firmware_status); | |
3411 | ||
3412 | #ifdef RTL8190P | |
3413 | //2008.06.03, for WOL 90 hw bug | |
3414 | ulRegRead &= (~(CPU_GEN_GPIO_UART)); | |
3415 | #endif | |
3416 | ||
3417 | write_nic_dword(dev, CPU_GEN, ulRegRead); | |
3418 | //mdelay(100); | |
3419 | ||
3420 | #ifdef RTL8192E | |
3421 | ||
3422 | //3// | |
3423 | //3 //Fix the issue of E-cut high temperature issue | |
3424 | //3// | |
3425 | // TODO: E cut only | |
3426 | ICVersion = read_nic_byte(dev, IC_VERRSION); | |
3427 | if(ICVersion >= 0x4) //E-cut only | |
3428 | { | |
3429 | // HW SD suggest that we should not wirte this register too often, so driver | |
3430 | // should readback this register. This register will be modified only when | |
3431 | // power on reset | |
3432 | SwitchingRegulatorOutput = read_nic_byte(dev, SWREGULATOR); | |
3433 | if(SwitchingRegulatorOutput != 0xb8) | |
3434 | { | |
3435 | write_nic_byte(dev, SWREGULATOR, 0xa8); | |
3436 | mdelay(1); | |
3437 | write_nic_byte(dev, SWREGULATOR, 0xb8); | |
3438 | } | |
3439 | } | |
3440 | #endif | |
3441 | ||
3442 | ||
3443 | //3// | |
3444 | //3// Initialize BB before MAC | |
3445 | //3// | |
ecdfa446 GKH |
3446 | RT_TRACE(COMP_INIT, "BB Config Start!\n"); |
3447 | rtStatus = rtl8192_BBConfig(dev); | |
3448 | if(rtStatus != RT_STATUS_SUCCESS) | |
3449 | { | |
3450 | RT_TRACE(COMP_ERR, "BB Config failed\n"); | |
3451 | return rtStatus; | |
3452 | } | |
3453 | RT_TRACE(COMP_INIT,"BB Config Finished!\n"); | |
3454 | ||
ecdfa446 GKH |
3455 | //3//Set Loopback mode or Normal mode |
3456 | //3// | |
3457 | //2006.12.13 by emily. Note!We should not merge these two CPU_GEN register writings | |
3458 | // because setting of System_Reset bit reset MAC to default transmission mode. | |
3459 | //Loopback mode or not | |
3460 | priv->LoopbackMode = RTL819X_NO_LOOPBACK; | |
3461 | //priv->LoopbackMode = RTL819X_MAC_LOOPBACK; | |
3462 | if(priv->ResetProgress == RESET_TYPE_NORESET) | |
3463 | { | |
3464 | ulRegRead = read_nic_dword(dev, CPU_GEN); | |
3465 | if(priv->LoopbackMode == RTL819X_NO_LOOPBACK) | |
3466 | { | |
3467 | ulRegRead = ((ulRegRead & CPU_GEN_NO_LOOPBACK_MSK) | CPU_GEN_NO_LOOPBACK_SET); | |
3468 | } | |
3469 | else if (priv->LoopbackMode == RTL819X_MAC_LOOPBACK ) | |
3470 | { | |
3471 | ulRegRead |= CPU_CCK_LOOPBACK; | |
3472 | } | |
3473 | else | |
3474 | { | |
3475 | RT_TRACE(COMP_ERR,"Serious error: wrong loopback mode setting\n"); | |
3476 | } | |
3477 | ||
3478 | //2008.06.03, for WOL | |
3479 | //ulRegRead &= (~(CPU_GEN_GPIO_UART)); | |
3480 | write_nic_dword(dev, CPU_GEN, ulRegRead); | |
3481 | ||
3482 | // 2006.11.29. After reset cpu, we sholud wait for a second, otherwise, it may fail to write registers. Emily | |
3483 | udelay(500); | |
3484 | } | |
3485 | //3Set Hardware(Do nothing now) | |
3486 | rtl8192_hwconfig(dev); | |
3487 | //2======================================================= | |
3488 | // Common Setting for all of the FPGA platform. (part 1) | |
3489 | //2======================================================= | |
3490 | // If there is changes, please make sure it applies to all of the FPGA version | |
3491 | //3 Turn on Tx/Rx | |
3492 | write_nic_byte(dev, CMDR, CR_RE|CR_TE); | |
3493 | ||
3494 | //2Set Tx dma burst | |
3495 | #ifdef RTL8190P | |
3496 | write_nic_byte(dev, PCIF, ((MXDMA2_NoLimit<<MXDMA2_RX_SHIFT) | \ | |
3497 | (MXDMA2_NoLimit<<MXDMA2_TX_SHIFT) | \ | |
3498 | (1<<MULRW_SHIFT))); | |
3499 | #else | |
3500 | #ifdef RTL8192E | |
3501 | write_nic_byte(dev, PCIF, ((MXDMA2_NoLimit<<MXDMA2_RX_SHIFT) |\ | |
3502 | (MXDMA2_NoLimit<<MXDMA2_TX_SHIFT) )); | |
3503 | #endif | |
3504 | #endif | |
3505 | //set IDR0 here | |
3506 | write_nic_dword(dev, MAC0, ((u32*)dev->dev_addr)[0]); | |
3507 | write_nic_word(dev, MAC4, ((u16*)(dev->dev_addr + 4))[0]); | |
3508 | //set RCR | |
3509 | write_nic_dword(dev, RCR, priv->ReceiveConfig); | |
3510 | ||
3511 | //3 Initialize Number of Reserved Pages in Firmware Queue | |
3512 | #ifdef TO_DO_LIST | |
3513 | if(priv->bInHctTest) | |
3514 | { | |
3515 | PlatformEFIOWrite4Byte(Adapter, RQPN1, NUM_OF_PAGE_IN_FW_QUEUE_BK_DTM << RSVD_FW_QUEUE_PAGE_BK_SHIFT |\ | |
3516 | NUM_OF_PAGE_IN_FW_QUEUE_BE_DTM << RSVD_FW_QUEUE_PAGE_BE_SHIFT | \ | |
3517 | NUM_OF_PAGE_IN_FW_QUEUE_VI_DTM << RSVD_FW_QUEUE_PAGE_VI_SHIFT | \ | |
3518 | NUM_OF_PAGE_IN_FW_QUEUE_VO_DTM <<RSVD_FW_QUEUE_PAGE_VO_SHIFT); | |
3519 | PlatformEFIOWrite4Byte(Adapter, RQPN2, NUM_OF_PAGE_IN_FW_QUEUE_MGNT << RSVD_FW_QUEUE_PAGE_MGNT_SHIFT); | |
3520 | PlatformEFIOWrite4Byte(Adapter, RQPN3, APPLIED_RESERVED_QUEUE_IN_FW| \ | |
3521 | NUM_OF_PAGE_IN_FW_QUEUE_BCN<<RSVD_FW_QUEUE_PAGE_BCN_SHIFT|\ | |
3522 | NUM_OF_PAGE_IN_FW_QUEUE_PUB_DTM<<RSVD_FW_QUEUE_PAGE_PUB_SHIFT); | |
3523 | } | |
3524 | else | |
3525 | #endif | |
3526 | { | |
3527 | write_nic_dword(dev, RQPN1, NUM_OF_PAGE_IN_FW_QUEUE_BK << RSVD_FW_QUEUE_PAGE_BK_SHIFT |\ | |
3528 | NUM_OF_PAGE_IN_FW_QUEUE_BE << RSVD_FW_QUEUE_PAGE_BE_SHIFT | \ | |
3529 | NUM_OF_PAGE_IN_FW_QUEUE_VI << RSVD_FW_QUEUE_PAGE_VI_SHIFT | \ | |
3530 | NUM_OF_PAGE_IN_FW_QUEUE_VO <<RSVD_FW_QUEUE_PAGE_VO_SHIFT); | |
3531 | write_nic_dword(dev, RQPN2, NUM_OF_PAGE_IN_FW_QUEUE_MGNT << RSVD_FW_QUEUE_PAGE_MGNT_SHIFT); | |
3532 | write_nic_dword(dev, RQPN3, APPLIED_RESERVED_QUEUE_IN_FW| \ | |
3533 | NUM_OF_PAGE_IN_FW_QUEUE_BCN<<RSVD_FW_QUEUE_PAGE_BCN_SHIFT|\ | |
3534 | NUM_OF_PAGE_IN_FW_QUEUE_PUB<<RSVD_FW_QUEUE_PAGE_PUB_SHIFT); | |
3535 | } | |
3536 | ||
3537 | rtl8192_tx_enable(dev); | |
3538 | rtl8192_rx_enable(dev); | |
3539 | //3Set Response Rate Setting Register | |
3540 | // CCK rate is supported by default. | |
3541 | // CCK rate will be filtered out only when associated AP does not support it. | |
3542 | ulRegRead = (0xFFF00000 & read_nic_dword(dev, RRSR)) | RATE_ALL_OFDM_AG | RATE_ALL_CCK; | |
3543 | write_nic_dword(dev, RRSR, ulRegRead); | |
3544 | write_nic_dword(dev, RATR0+4*7, (RATE_ALL_OFDM_AG | RATE_ALL_CCK)); | |
3545 | ||
3546 | //2Set AckTimeout | |
3547 | // TODO: (it value is only for FPGA version). need to be changed!!2006.12.18, by Emily | |
3548 | write_nic_byte(dev, ACK_TIMEOUT, 0x30); | |
3549 | ||
3550 | //rtl8192_actset_wirelessmode(dev,priv->RegWirelessMode); | |
3551 | if(priv->ResetProgress == RESET_TYPE_NORESET) | |
3552 | rtl8192_SetWirelessMode(dev, priv->ieee80211->mode); | |
3553 | //----------------------------------------------------------------------------- | |
3554 | // Set up security related. 070106, by rcnjko: | |
3555 | // 1. Clear all H/W keys. | |
3556 | // 2. Enable H/W encryption/decryption. | |
3557 | //----------------------------------------------------------------------------- | |
3558 | CamResetAllEntry(dev); | |
3559 | { | |
3560 | u8 SECR_value = 0x0; | |
3561 | SECR_value |= SCR_TxEncEnable; | |
3562 | SECR_value |= SCR_RxDecEnable; | |
3563 | SECR_value |= SCR_NoSKMC; | |
3564 | write_nic_byte(dev, SECR, SECR_value); | |
3565 | } | |
3566 | //3Beacon related | |
3567 | write_nic_word(dev, ATIMWND, 2); | |
3568 | write_nic_word(dev, BCN_INTERVAL, 100); | |
5e1ad18a | 3569 | for (i=0; i<QOS_QUEUE_NUM; i++) |
ecdfa446 | 3570 | write_nic_dword(dev, WDCAPARA_ADD[i], 0x005e4332); |
ecdfa446 GKH |
3571 | // |
3572 | // Switching regulator controller: This is set temporarily. | |
3573 | // It's not sure if this can be removed in the future. | |
3574 | // PJ advised to leave it by default. | |
3575 | // | |
3576 | write_nic_byte(dev, 0xbe, 0xc0); | |
3577 | ||
3578 | //2======================================================= | |
3579 | // Set PHY related configuration defined in MAC register bank | |
3580 | //2======================================================= | |
3581 | rtl8192_phy_configmac(dev); | |
3582 | ||
3583 | if (priv->card_8192_version > (u8) VERSION_8190_BD) { | |
3584 | rtl8192_phy_getTxPower(dev); | |
3585 | rtl8192_phy_setTxPower(dev, priv->chan); | |
3586 | } | |
3587 | ||
3588 | //if D or C cut | |
3589 | tmpvalue = read_nic_byte(dev, IC_VERRSION); | |
3590 | priv->IC_Cut = tmpvalue; | |
3591 | RT_TRACE(COMP_INIT, "priv->IC_Cut = 0x%x\n", priv->IC_Cut); | |
3592 | if(priv->IC_Cut >= IC_VersionCut_D) | |
3593 | { | |
3594 | //pHalData->bDcut = TRUE; | |
3595 | if(priv->IC_Cut == IC_VersionCut_D) | |
3596 | RT_TRACE(COMP_INIT, "D-cut\n"); | |
3597 | if(priv->IC_Cut == IC_VersionCut_E) | |
3598 | { | |
3599 | RT_TRACE(COMP_INIT, "E-cut\n"); | |
3600 | // HW SD suggest that we should not wirte this register too often, so driver | |
3601 | // should readback this register. This register will be modified only when | |
3602 | // power on reset | |
3603 | } | |
3604 | } | |
3605 | else | |
3606 | { | |
3607 | //pHalData->bDcut = FALSE; | |
3608 | RT_TRACE(COMP_INIT, "Before C-cut\n"); | |
3609 | } | |
3610 | ||
3611 | #if 1 | |
3612 | //Firmware download | |
3613 | RT_TRACE(COMP_INIT, "Load Firmware!\n"); | |
3614 | bfirmwareok = init_firmware(dev); | |
3615 | if(bfirmwareok != true) { | |
3616 | rtStatus = RT_STATUS_FAILURE; | |
3617 | return rtStatus; | |
3618 | } | |
3619 | RT_TRACE(COMP_INIT, "Load Firmware finished!\n"); | |
3620 | #endif | |
3621 | //RF config | |
3622 | if(priv->ResetProgress == RESET_TYPE_NORESET) | |
3623 | { | |
3624 | RT_TRACE(COMP_INIT, "RF Config Started!\n"); | |
3625 | rtStatus = rtl8192_phy_RFConfig(dev); | |
3626 | if(rtStatus != RT_STATUS_SUCCESS) | |
3627 | { | |
3628 | RT_TRACE(COMP_ERR, "RF Config failed\n"); | |
3629 | return rtStatus; | |
3630 | } | |
3631 | RT_TRACE(COMP_INIT, "RF Config Finished!\n"); | |
3632 | } | |
3633 | rtl8192_phy_updateInitGain(dev); | |
3634 | ||
3635 | /*---- Set CCK and OFDM Block "ON"----*/ | |
3636 | rtl8192_setBBreg(dev, rFPGA0_RFMOD, bCCKEn, 0x1); | |
3637 | rtl8192_setBBreg(dev, rFPGA0_RFMOD, bOFDMEn, 0x1); | |
3638 | ||
3639 | #ifdef RTL8192E | |
3640 | //Enable Led | |
3641 | write_nic_byte(dev, 0x87, 0x0); | |
3642 | #endif | |
3643 | #ifdef RTL8190P | |
3644 | //2008.06.03, for WOL | |
3645 | ucRegRead = read_nic_byte(dev, GPE); | |
3646 | ucRegRead |= BIT0; | |
3647 | write_nic_byte(dev, GPE, ucRegRead); | |
3648 | ||
3649 | ucRegRead = read_nic_byte(dev, GPO); | |
3650 | ucRegRead &= ~BIT0; | |
3651 | write_nic_byte(dev, GPO, ucRegRead); | |
3652 | #endif | |
3653 | ||
3654 | //2======================================================= | |
3655 | // RF Power Save | |
3656 | //2======================================================= | |
3657 | #ifdef ENABLE_IPS | |
3658 | ||
3659 | { | |
3660 | if(priv->RegRfOff == TRUE) | |
3661 | { // User disable RF via registry. | |
3662 | RT_TRACE((COMP_INIT|COMP_RF|COMP_POWER), "%s(): Turn off RF for RegRfOff ----------\n",__FUNCTION__); | |
3663 | MgntActSet_RF_State(dev, eRfOff, RF_CHANGE_BY_SW); | |
3664 | #if 0//cosa, ask SD3 willis and he doesn't know what is this for | |
3665 | // Those action will be discard in MgntActSet_RF_State because off the same state | |
3666 | for(eRFPath = 0; eRFPath <pHalData->NumTotalRFPath; eRFPath++) | |
3667 | PHY_SetRFReg(Adapter, (RF90_RADIO_PATH_E)eRFPath, 0x4, 0xC00, 0x0); | |
3668 | #endif | |
3669 | } | |
3670 | else if(priv->ieee80211->RfOffReason > RF_CHANGE_BY_PS) | |
3671 | { // H/W or S/W RF OFF before sleep. | |
3672 | RT_TRACE((COMP_INIT|COMP_RF|COMP_POWER), "%s(): Turn off RF for RfOffReason(%d) ----------\n", __FUNCTION__,priv->ieee80211->RfOffReason); | |
3673 | MgntActSet_RF_State(dev, eRfOff, priv->ieee80211->RfOffReason); | |
3674 | } | |
3675 | else if(priv->ieee80211->RfOffReason >= RF_CHANGE_BY_IPS) | |
3676 | { // H/W or S/W RF OFF before sleep. | |
3677 | RT_TRACE((COMP_INIT|COMP_RF|COMP_POWER), "%s(): Turn off RF for RfOffReason(%d) ----------\n", __FUNCTION__,priv->ieee80211->RfOffReason); | |
3678 | MgntActSet_RF_State(dev, eRfOff, priv->ieee80211->RfOffReason); | |
3679 | } | |
3680 | else | |
3681 | { | |
3682 | RT_TRACE((COMP_INIT|COMP_RF|COMP_POWER), "%s(): RF-ON \n",__FUNCTION__); | |
3683 | priv->ieee80211->eRFPowerState = eRfOn; | |
3684 | priv->ieee80211->RfOffReason = 0; | |
3685 | //DrvIFIndicateCurrentPhyStatus(Adapter); | |
3686 | // LED control | |
3687 | //Adapter->HalFunc.LedControlHandler(Adapter, LED_CTL_POWER_ON); | |
3688 | ||
3689 | // | |
3690 | // If inactive power mode is enabled, disable rf while in disconnected state. | |
3691 | // But we should still tell upper layer we are in rf on state. | |
3692 | // 2007.07.16, by shien chang. | |
3693 | // | |
3694 | //if(!Adapter->bInHctTest) | |
3695 | //IPSEnter(Adapter); | |
3696 | ||
3697 | } | |
3698 | } | |
3699 | #endif | |
3700 | if(1){ | |
3701 | #ifdef RTL8192E | |
3702 | // We can force firmware to do RF-R/W | |
3703 | if(priv->ieee80211->FwRWRF) | |
3704 | priv->Rf_Mode = RF_OP_By_FW; | |
3705 | else | |
3706 | priv->Rf_Mode = RF_OP_By_SW_3wire; | |
3707 | #else | |
3708 | priv->Rf_Mode = RF_OP_By_SW_3wire; | |
3709 | #endif | |
3710 | } | |
3711 | #ifdef RTL8190P | |
3712 | if(priv->ResetProgress == RESET_TYPE_NORESET) | |
3713 | { | |
3714 | dm_initialize_txpower_tracking(dev); | |
3715 | ||
3716 | tmpRegA= rtl8192_QueryBBReg(dev,rOFDM0_XATxIQImbalance,bMaskDWord); | |
3717 | tmpRegC= rtl8192_QueryBBReg(dev,rOFDM0_XCTxIQImbalance,bMaskDWord); | |
3718 | ||
3719 | if(priv->rf_type == RF_2T4R){ | |
3720 | for(i = 0; i<TxBBGainTableLength; i++) | |
3721 | { | |
3722 | if(tmpRegA == priv->txbbgain_table[i].txbbgain_value) | |
3723 | { | |
3724 | priv->rfa_txpowertrackingindex= (u8)i; | |
3725 | priv->rfa_txpowertrackingindex_real= (u8)i; | |
3726 | priv->rfa_txpowertracking_default = priv->rfa_txpowertrackingindex; | |
3727 | break; | |
3728 | } | |
3729 | } | |
3730 | } | |
3731 | for(i = 0; i<TxBBGainTableLength; i++) | |
3732 | { | |
3733 | if(tmpRegC == priv->txbbgain_table[i].txbbgain_value) | |
3734 | { | |
3735 | priv->rfc_txpowertrackingindex= (u8)i; | |
3736 | priv->rfc_txpowertrackingindex_real= (u8)i; | |
3737 | priv->rfc_txpowertracking_default = priv->rfc_txpowertrackingindex; | |
3738 | break; | |
3739 | } | |
3740 | } | |
3741 | TempCCk = rtl8192_QueryBBReg(dev, rCCK0_TxFilter1, bMaskByte2); | |
3742 | ||
3743 | for(i=0 ; i<CCKTxBBGainTableLength ; i++) | |
3744 | { | |
3745 | if(TempCCk == priv->cck_txbbgain_table[i].ccktxbb_valuearray[0]) | |
3746 | { | |
3747 | priv->CCKPresentAttentuation_20Mdefault =(u8) i; | |
3748 | break; | |
3749 | } | |
3750 | } | |
3751 | priv->CCKPresentAttentuation_40Mdefault = 0; | |
3752 | priv->CCKPresentAttentuation_difference = 0; | |
3753 | priv->CCKPresentAttentuation = priv->CCKPresentAttentuation_20Mdefault; | |
3754 | RT_TRACE(COMP_POWER_TRACKING, "priv->rfa_txpowertrackingindex_initial = %d\n", priv->rfa_txpowertrackingindex); | |
3755 | RT_TRACE(COMP_POWER_TRACKING, "priv->rfa_txpowertrackingindex_real__initial = %d\n", priv->rfa_txpowertrackingindex_real); | |
3756 | RT_TRACE(COMP_POWER_TRACKING, "priv->rfc_txpowertrackingindex_initial = %d\n", priv->rfc_txpowertrackingindex); | |
3757 | RT_TRACE(COMP_POWER_TRACKING, "priv->rfc_txpowertrackingindex_real_initial = %d\n", priv->rfc_txpowertrackingindex_real); | |
3758 | RT_TRACE(COMP_POWER_TRACKING, "priv->CCKPresentAttentuation_difference_initial = %d\n", priv->CCKPresentAttentuation_difference); | |
3759 | RT_TRACE(COMP_POWER_TRACKING, "priv->CCKPresentAttentuation_initial = %d\n", priv->CCKPresentAttentuation); | |
3760 | } | |
3761 | #else | |
3762 | #ifdef RTL8192E | |
3763 | if(priv->ResetProgress == RESET_TYPE_NORESET) | |
3764 | { | |
3765 | dm_initialize_txpower_tracking(dev); | |
3766 | ||
3767 | if(priv->IC_Cut >= IC_VersionCut_D) | |
3768 | { | |
3769 | tmpRegA= rtl8192_QueryBBReg(dev,rOFDM0_XATxIQImbalance,bMaskDWord); | |
3770 | tmpRegC= rtl8192_QueryBBReg(dev,rOFDM0_XCTxIQImbalance,bMaskDWord); | |
3771 | for(i = 0; i<TxBBGainTableLength; i++) | |
3772 | { | |
3773 | if(tmpRegA == priv->txbbgain_table[i].txbbgain_value) | |
3774 | { | |
3775 | priv->rfa_txpowertrackingindex= (u8)i; | |
3776 | priv->rfa_txpowertrackingindex_real= (u8)i; | |
3777 | priv->rfa_txpowertracking_default = priv->rfa_txpowertrackingindex; | |
3778 | break; | |
3779 | } | |
3780 | } | |
3781 | ||
3782 | TempCCk = rtl8192_QueryBBReg(dev, rCCK0_TxFilter1, bMaskByte2); | |
3783 | ||
3784 | for(i=0 ; i<CCKTxBBGainTableLength ; i++) | |
3785 | { | |
3786 | if(TempCCk == priv->cck_txbbgain_table[i].ccktxbb_valuearray[0]) | |
3787 | { | |
3788 | priv->CCKPresentAttentuation_20Mdefault =(u8) i; | |
3789 | break; | |
3790 | } | |
3791 | } | |
3792 | priv->CCKPresentAttentuation_40Mdefault = 0; | |
3793 | priv->CCKPresentAttentuation_difference = 0; | |
3794 | priv->CCKPresentAttentuation = priv->CCKPresentAttentuation_20Mdefault; | |
3795 | RT_TRACE(COMP_POWER_TRACKING, "priv->rfa_txpowertrackingindex_initial = %d\n", priv->rfa_txpowertrackingindex); | |
3796 | RT_TRACE(COMP_POWER_TRACKING, "priv->rfa_txpowertrackingindex_real__initial = %d\n", priv->rfa_txpowertrackingindex_real); | |
3797 | RT_TRACE(COMP_POWER_TRACKING, "priv->CCKPresentAttentuation_difference_initial = %d\n", priv->CCKPresentAttentuation_difference); | |
3798 | RT_TRACE(COMP_POWER_TRACKING, "priv->CCKPresentAttentuation_initial = %d\n", priv->CCKPresentAttentuation); | |
3799 | priv->btxpower_tracking = FALSE;//TEMPLY DISABLE | |
3800 | } | |
3801 | } | |
3802 | #endif | |
3803 | #endif | |
3804 | rtl8192_irq_enable(dev); | |
3805 | priv->being_init_adapter = false; | |
3806 | return rtStatus; | |
3807 | ||
3808 | } | |
3809 | ||
3810 | void rtl8192_prepare_beacon(struct r8192_priv *priv) | |
3811 | { | |
3812 | struct sk_buff *skb; | |
3813 | //unsigned long flags; | |
3814 | cb_desc *tcb_desc; | |
3815 | ||
3816 | skb = ieee80211_get_beacon(priv->ieee80211); | |
3817 | tcb_desc = (cb_desc *)(skb->cb + 8); | |
3818 | //printk("===========> %s\n", __FUNCTION__); | |
3819 | //spin_lock_irqsave(&priv->tx_lock,flags); | |
3820 | /* prepare misc info for the beacon xmit */ | |
3821 | tcb_desc->queue_index = BEACON_QUEUE; | |
bbc9a991 | 3822 | /* IBSS does not support HT yet, use 1M defaultly */ |
ecdfa446 GKH |
3823 | tcb_desc->data_rate = 2; |
3824 | tcb_desc->RATRIndex = 7; | |
3825 | tcb_desc->bTxDisableRateFallBack = 1; | |
3826 | tcb_desc->bTxUseDriverAssingedRate = 1; | |
3827 | ||
3828 | skb_push(skb, priv->ieee80211->tx_headroom); | |
3829 | if(skb){ | |
3830 | rtl8192_tx(priv->ieee80211->dev,skb); | |
3831 | } | |
3832 | //spin_unlock_irqrestore (&priv->tx_lock, flags); | |
3833 | } | |
3834 | ||
ecdfa446 GKH |
3835 | |
3836 | /* this configures registers for beacon tx and enables it via | |
3837 | * rtl8192_beacon_tx_enable(). rtl8192_beacon_tx_disable() might | |
3838 | * be used to stop beacon transmission | |
3839 | */ | |
3840 | void rtl8192_start_beacon(struct net_device *dev) | |
3841 | { | |
3842 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
3843 | struct ieee80211_network *net = &priv->ieee80211->current_network; | |
3844 | u16 BcnTimeCfg = 0; | |
3845 | u16 BcnCW = 6; | |
3846 | u16 BcnIFS = 0xf; | |
3847 | ||
3848 | DMESG("Enabling beacon TX"); | |
3849 | //rtl8192_prepare_beacon(dev); | |
3850 | rtl8192_irq_disable(dev); | |
3851 | //rtl8192_beacon_tx_enable(dev); | |
3852 | ||
3853 | /* ATIM window */ | |
3854 | write_nic_word(dev, ATIMWND, 2); | |
3855 | ||
3856 | /* Beacon interval (in unit of TU) */ | |
3857 | write_nic_word(dev, BCN_INTERVAL, net->beacon_interval); | |
3858 | ||
3859 | /* | |
3860 | * DrvErlyInt (in unit of TU). | |
3861 | * (Time to send interrupt to notify driver to c | |
3862 | * hange beacon content) | |
3863 | * */ | |
3864 | write_nic_word(dev, BCN_DRV_EARLY_INT, 10); | |
3865 | ||
3866 | /* | |
3867 | * BcnDMATIM(in unit of us). | |
3868 | * Indicates the time before TBTT to perform beacon queue DMA | |
3869 | * */ | |
3870 | write_nic_word(dev, BCN_DMATIME, 256); | |
3871 | ||
3872 | /* | |
3873 | * Force beacon frame transmission even after receiving | |
3874 | * beacon frame from other ad hoc STA | |
3875 | * */ | |
3876 | write_nic_byte(dev, BCN_ERR_THRESH, 100); | |
3877 | ||
3878 | /* Set CW and IFS */ | |
3879 | BcnTimeCfg |= BcnCW<<BCN_TCFG_CW_SHIFT; | |
3880 | BcnTimeCfg |= BcnIFS<<BCN_TCFG_IFS; | |
3881 | write_nic_word(dev, BCN_TCFG, BcnTimeCfg); | |
3882 | ||
3883 | ||
3884 | /* enable the interrupt for ad-hoc process */ | |
3885 | rtl8192_irq_enable(dev); | |
3886 | } | |
3887 | /*************************************************************************** | |
3888 | -------------------------------NET STUFF--------------------------- | |
3889 | ***************************************************************************/ | |
ecdfa446 GKH |
3890 | |
3891 | ||
3892 | ||
5e1ad18a | 3893 | static bool HalTxCheckStuck8190Pci(struct net_device *dev) |
ecdfa446 GKH |
3894 | { |
3895 | u16 RegTxCounter = read_nic_word(dev, 0x128); | |
3896 | struct r8192_priv *priv = ieee80211_priv(dev); | |
3897 | bool bStuck = FALSE; | |
3898 | RT_TRACE(COMP_RESET,"%s():RegTxCounter is %d,TxCounter is %d\n",__FUNCTION__,RegTxCounter,priv->TxCounter); | |
3899 | if(priv->TxCounter==RegTxCounter) | |
3900 | bStuck = TRUE; | |
3901 | ||
3902 | priv->TxCounter = RegTxCounter; | |
3903 | ||
3904 | return bStuck; | |
3905 | } | |
3906 | ||
3907 | /* | |
3908 | * <Assumption: RT_TX_SPINLOCK is acquired.> | |
3909 | * First added: 2006.11.19 by emily | |
3910 | */ | |
5e1ad18a | 3911 | static RESET_TYPE |
ecdfa446 GKH |
3912 | TxCheckStuck(struct net_device *dev) |
3913 | { | |
3914 | struct r8192_priv *priv = ieee80211_priv(dev); | |
3915 | u8 QueueID; | |
3916 | ptx_ring head=NULL,tail=NULL,txring = NULL; | |
3917 | u8 ResetThreshold = NIC_SEND_HANG_THRESHOLD_POWERSAVE; | |
3918 | bool bCheckFwTxCnt = false; | |
3919 | //unsigned long flags; | |
3920 | ||
3921 | // | |
3922 | // Decide Stuch threshold according to current power save mode | |
3923 | // | |
3924 | //printk("++++++++++++>%s()\n",__FUNCTION__); | |
3925 | switch (priv->ieee80211->dot11PowerSaveMode) | |
3926 | { | |
3927 | // The threshold value may required to be adjusted . | |
3928 | case eActive: // Active/Continuous access. | |
3929 | ResetThreshold = NIC_SEND_HANG_THRESHOLD_NORMAL; | |
3930 | break; | |
3931 | case eMaxPs: // Max power save mode. | |
3932 | ResetThreshold = NIC_SEND_HANG_THRESHOLD_POWERSAVE; | |
3933 | break; | |
3934 | case eFastPs: // Fast power save mode. | |
3935 | ResetThreshold = NIC_SEND_HANG_THRESHOLD_POWERSAVE; | |
3936 | break; | |
3937 | } | |
3938 | ||
3939 | // | |
3940 | // Check whether specific tcb has been queued for a specific time | |
3941 | // | |
3942 | for(QueueID = 0; QueueID < MAX_TX_QUEUE; QueueID++) | |
3943 | { | |
3944 | ||
3945 | ||
3946 | if(QueueID == TXCMD_QUEUE) | |
3947 | continue; | |
3948 | ||
3949 | switch(QueueID) { | |
3950 | case MGNT_QUEUE: | |
3951 | tail=priv->txmapringtail; | |
3952 | head=priv->txmapringhead; | |
3953 | break; | |
3954 | ||
3955 | case BK_QUEUE: | |
3956 | tail=priv->txbkpringtail; | |
3957 | head=priv->txbkpringhead; | |
3958 | break; | |
3959 | ||
3960 | case BE_QUEUE: | |
3961 | tail=priv->txbepringtail; | |
3962 | head=priv->txbepringhead; | |
3963 | break; | |
3964 | ||
3965 | case VI_QUEUE: | |
3966 | tail=priv->txvipringtail; | |
3967 | head=priv->txvipringhead; | |
3968 | break; | |
3969 | ||
3970 | case VO_QUEUE: | |
3971 | tail=priv->txvopringtail; | |
3972 | head=priv->txvopringhead; | |
3973 | break; | |
3974 | ||
3975 | default: | |
3976 | tail=head=NULL; | |
3977 | break; | |
3978 | } | |
3979 | ||
3980 | if(tail == head) | |
3981 | continue; | |
3982 | else | |
3983 | { | |
3984 | txring = head; | |
3985 | if(txring == NULL) | |
3986 | { | |
3987 | RT_TRACE(COMP_ERR,"%s():txring is NULL , BUG!\n",__FUNCTION__); | |
3988 | continue; | |
3989 | } | |
3990 | txring->nStuckCount++; | |
ecdfa446 GKH |
3991 | bCheckFwTxCnt = TRUE; |
3992 | } | |
3993 | } | |
3994 | #if 1 | |
3995 | if(bCheckFwTxCnt) | |
3996 | { | |
3997 | if(HalTxCheckStuck8190Pci(dev)) | |
3998 | { | |
3999 | RT_TRACE(COMP_RESET, "TxCheckStuck(): Fw indicates no Tx condition! \n"); | |
4000 | return RESET_TYPE_SILENT; | |
4001 | } | |
4002 | } | |
4003 | #endif | |
4004 | return RESET_TYPE_NORESET; | |
4005 | } | |
4006 | ||
4007 | ||
5e1ad18a | 4008 | static bool HalRxCheckStuck8190Pci(struct net_device *dev) |
ecdfa446 GKH |
4009 | { |
4010 | struct r8192_priv *priv = ieee80211_priv(dev); | |
4011 | u16 RegRxCounter = read_nic_word(dev, 0x130); | |
4012 | bool bStuck = FALSE; | |
4013 | static u8 rx_chk_cnt = 0; | |
4014 | RT_TRACE(COMP_RESET,"%s(): RegRxCounter is %d,RxCounter is %d\n",__FUNCTION__,RegRxCounter,priv->RxCounter); | |
4015 | // If rssi is small, we should check rx for long time because of bad rx. | |
4016 | // or maybe it will continuous silent reset every 2 seconds. | |
4017 | rx_chk_cnt++; | |
4018 | if(priv->undecorated_smoothed_pwdb >= (RateAdaptiveTH_High+5)) | |
4019 | { | |
4020 | rx_chk_cnt = 0; //high rssi, check rx stuck right now. | |
4021 | } | |
4022 | else if(priv->undecorated_smoothed_pwdb < (RateAdaptiveTH_High+5) && | |
4023 | ((priv->CurrentChannelBW!=HT_CHANNEL_WIDTH_20&&priv->undecorated_smoothed_pwdb>=RateAdaptiveTH_Low_40M) || | |
4024 | (priv->CurrentChannelBW==HT_CHANNEL_WIDTH_20&&priv->undecorated_smoothed_pwdb>=RateAdaptiveTH_Low_20M)) ) | |
4025 | ||
4026 | { | |
4027 | if(rx_chk_cnt < 2) | |
4028 | { | |
4029 | return bStuck; | |
4030 | } | |
4031 | else | |
4032 | { | |
4033 | rx_chk_cnt = 0; | |
4034 | } | |
4035 | } | |
4036 | else if(((priv->CurrentChannelBW!=HT_CHANNEL_WIDTH_20&&priv->undecorated_smoothed_pwdb<RateAdaptiveTH_Low_40M) || | |
4037 | (priv->CurrentChannelBW==HT_CHANNEL_WIDTH_20&&priv->undecorated_smoothed_pwdb<RateAdaptiveTH_Low_20M)) && | |
4038 | priv->undecorated_smoothed_pwdb >= VeryLowRSSI) | |
4039 | { | |
4040 | if(rx_chk_cnt < 4) | |
4041 | { | |
4042 | //DbgPrint("RSSI < %d && RSSI >= %d, no check this time \n", RateAdaptiveTH_Low, VeryLowRSSI); | |
4043 | return bStuck; | |
4044 | } | |
4045 | else | |
4046 | { | |
4047 | rx_chk_cnt = 0; | |
4048 | //DbgPrint("RSSI < %d && RSSI >= %d, check this time \n", RateAdaptiveTH_Low, VeryLowRSSI); | |
4049 | } | |
4050 | } | |
4051 | else | |
4052 | { | |
4053 | if(rx_chk_cnt < 8) | |
4054 | { | |
4055 | //DbgPrint("RSSI <= %d, no check this time \n", VeryLowRSSI); | |
4056 | return bStuck; | |
4057 | } | |
4058 | else | |
4059 | { | |
4060 | rx_chk_cnt = 0; | |
4061 | //DbgPrint("RSSI <= %d, check this time \n", VeryLowRSSI); | |
4062 | } | |
4063 | } | |
ecdfa446 GKH |
4064 | if(priv->RxCounter==RegRxCounter) |
4065 | bStuck = TRUE; | |
4066 | ||
4067 | priv->RxCounter = RegRxCounter; | |
4068 | ||
4069 | return bStuck; | |
4070 | } | |
4071 | ||
5e1ad18a | 4072 | static RESET_TYPE RxCheckStuck(struct net_device *dev) |
ecdfa446 GKH |
4073 | { |
4074 | ||
4075 | if(HalRxCheckStuck8190Pci(dev)) | |
4076 | { | |
4077 | RT_TRACE(COMP_RESET, "RxStuck Condition\n"); | |
4078 | return RESET_TYPE_SILENT; | |
4079 | } | |
4080 | ||
4081 | return RESET_TYPE_NORESET; | |
4082 | } | |
4083 | ||
5e1ad18a | 4084 | static RESET_TYPE |
ecdfa446 GKH |
4085 | rtl819x_ifcheck_resetornot(struct net_device *dev) |
4086 | { | |
4087 | struct r8192_priv *priv = ieee80211_priv(dev); | |
4088 | RESET_TYPE TxResetType = RESET_TYPE_NORESET; | |
4089 | RESET_TYPE RxResetType = RESET_TYPE_NORESET; | |
4090 | RT_RF_POWER_STATE rfState; | |
4091 | ||
4092 | rfState = priv->ieee80211->eRFPowerState; | |
4093 | ||
4094 | TxResetType = TxCheckStuck(dev); | |
4095 | #if 1 | |
4096 | if( rfState != eRfOff && | |
4097 | /*ADAPTER_TEST_STATUS_FLAG(Adapter, ADAPTER_STATUS_FW_DOWNLOAD_FAILURE)) &&*/ | |
4098 | (priv->ieee80211->iw_mode != IW_MODE_ADHOC)) | |
4099 | { | |
4100 | // If driver is in the status of firmware download failure , driver skips RF initialization and RF is | |
4101 | // in turned off state. Driver should check whether Rx stuck and do silent reset. And | |
4102 | // if driver is in firmware download failure status, driver should initialize RF in the following | |
4103 | // silent reset procedure Emily, 2008.01.21 | |
4104 | ||
4105 | // Driver should not check RX stuck in IBSS mode because it is required to | |
4106 | // set Check BSSID in order to send beacon, however, if check BSSID is | |
4107 | // set, STA cannot hear any packet a all. Emily, 2008.04.12 | |
4108 | RxResetType = RxCheckStuck(dev); | |
4109 | } | |
4110 | #endif | |
4111 | ||
4112 | RT_TRACE(COMP_RESET,"%s(): TxResetType is %d, RxResetType is %d\n",__FUNCTION__,TxResetType,RxResetType); | |
4113 | if(TxResetType==RESET_TYPE_NORMAL || RxResetType==RESET_TYPE_NORMAL) | |
4114 | return RESET_TYPE_NORMAL; | |
4115 | else if(TxResetType==RESET_TYPE_SILENT || RxResetType==RESET_TYPE_SILENT) | |
4116 | return RESET_TYPE_SILENT; | |
4117 | else | |
4118 | return RESET_TYPE_NORESET; | |
4119 | ||
4120 | } | |
4121 | ||
4122 | ||
5e1ad18a | 4123 | static void CamRestoreAllEntry(struct net_device *dev) |
ecdfa446 GKH |
4124 | { |
4125 | u8 EntryId = 0; | |
4126 | struct r8192_priv *priv = ieee80211_priv(dev); | |
4127 | u8* MacAddr = priv->ieee80211->current_network.bssid; | |
4128 | ||
4129 | static u8 CAM_CONST_ADDR[4][6] = { | |
4130 | {0x00, 0x00, 0x00, 0x00, 0x00, 0x00}, | |
4131 | {0x00, 0x00, 0x00, 0x00, 0x00, 0x01}, | |
4132 | {0x00, 0x00, 0x00, 0x00, 0x00, 0x02}, | |
4133 | {0x00, 0x00, 0x00, 0x00, 0x00, 0x03}}; | |
4134 | static u8 CAM_CONST_BROAD[] = | |
4135 | {0xff, 0xff, 0xff, 0xff, 0xff, 0xff}; | |
4136 | ||
4137 | RT_TRACE(COMP_SEC, "CamRestoreAllEntry: \n"); | |
4138 | ||
4139 | ||
4140 | if ((priv->ieee80211->pairwise_key_type == KEY_TYPE_WEP40)|| | |
4141 | (priv->ieee80211->pairwise_key_type == KEY_TYPE_WEP104)) | |
4142 | { | |
4143 | ||
4144 | for(EntryId=0; EntryId<4; EntryId++) | |
4145 | { | |
4146 | { | |
4147 | MacAddr = CAM_CONST_ADDR[EntryId]; | |
4148 | setKey(dev, | |
4149 | EntryId , | |
4150 | EntryId, | |
4151 | priv->ieee80211->pairwise_key_type, | |
4152 | MacAddr, | |
4153 | 0, | |
4154 | NULL); | |
4155 | } | |
4156 | } | |
4157 | ||
4158 | } | |
4159 | else if(priv->ieee80211->pairwise_key_type == KEY_TYPE_TKIP) | |
4160 | { | |
4161 | ||
4162 | { | |
4163 | if(priv->ieee80211->iw_mode == IW_MODE_ADHOC) | |
4164 | setKey(dev, | |
4165 | 4, | |
4166 | 0, | |
4167 | priv->ieee80211->pairwise_key_type, | |
4168 | (u8*)dev->dev_addr, | |
4169 | 0, | |
4170 | NULL); | |
4171 | else | |
4172 | setKey(dev, | |
4173 | 4, | |
4174 | 0, | |
4175 | priv->ieee80211->pairwise_key_type, | |
4176 | MacAddr, | |
4177 | 0, | |
4178 | NULL); | |
4179 | } | |
4180 | } | |
4181 | else if(priv->ieee80211->pairwise_key_type == KEY_TYPE_CCMP) | |
4182 | { | |
4183 | ||
4184 | { | |
4185 | if(priv->ieee80211->iw_mode == IW_MODE_ADHOC) | |
4186 | setKey(dev, | |
4187 | 4, | |
4188 | 0, | |
4189 | priv->ieee80211->pairwise_key_type, | |
4190 | (u8*)dev->dev_addr, | |
4191 | 0, | |
4192 | NULL); | |
4193 | else | |
4194 | setKey(dev, | |
4195 | 4, | |
4196 | 0, | |
4197 | priv->ieee80211->pairwise_key_type, | |
4198 | MacAddr, | |
4199 | 0, | |
4200 | NULL); | |
4201 | } | |
4202 | } | |
4203 | ||
4204 | ||
4205 | ||
4206 | if(priv->ieee80211->group_key_type == KEY_TYPE_TKIP) | |
4207 | { | |
4208 | MacAddr = CAM_CONST_BROAD; | |
4209 | for(EntryId=1 ; EntryId<4 ; EntryId++) | |
4210 | { | |
4211 | { | |
4212 | setKey(dev, | |
4213 | EntryId, | |
4214 | EntryId, | |
4215 | priv->ieee80211->group_key_type, | |
4216 | MacAddr, | |
4217 | 0, | |
4218 | NULL); | |
4219 | } | |
4220 | } | |
4221 | if(priv->ieee80211->iw_mode == IW_MODE_ADHOC) | |
4222 | setKey(dev, | |
4223 | 0, | |
4224 | 0, | |
4225 | priv->ieee80211->group_key_type, | |
4226 | CAM_CONST_ADDR[0], | |
4227 | 0, | |
4228 | NULL); | |
4229 | } | |
4230 | else if(priv->ieee80211->group_key_type == KEY_TYPE_CCMP) | |
4231 | { | |
4232 | MacAddr = CAM_CONST_BROAD; | |
4233 | for(EntryId=1; EntryId<4 ; EntryId++) | |
4234 | { | |
4235 | { | |
4236 | setKey(dev, | |
4237 | EntryId , | |
4238 | EntryId, | |
4239 | priv->ieee80211->group_key_type, | |
4240 | MacAddr, | |
4241 | 0, | |
4242 | NULL); | |
4243 | } | |
4244 | } | |
4245 | ||
4246 | if(priv->ieee80211->iw_mode == IW_MODE_ADHOC) | |
4247 | setKey(dev, | |
4248 | 0 , | |
4249 | 0, | |
4250 | priv->ieee80211->group_key_type, | |
4251 | CAM_CONST_ADDR[0], | |
4252 | 0, | |
4253 | NULL); | |
4254 | } | |
4255 | } | |
4256 | ||
4257 | void rtl8192_cancel_deferred_work(struct r8192_priv* priv); | |
4258 | int _rtl8192_up(struct net_device *dev); | |
4259 | ||
4260 | /* | |
4261 | * This function is used to fix Tx/Rx stop bug temporarily. | |
4262 | * This function will do "system reset" to NIC when Tx or Rx is stuck. | |
4263 | * The method checking Tx/Rx stuck of this function is supported by FW, | |
4264 | * which reports Tx and Rx counter to register 0x128 and 0x130. | |
4265 | * */ | |
5e1ad18a | 4266 | static void rtl819x_ifsilentreset(struct net_device *dev) |
ecdfa446 GKH |
4267 | { |
4268 | struct r8192_priv *priv = ieee80211_priv(dev); | |
4269 | u8 reset_times = 0; | |
4270 | int reset_status = 0; | |
4271 | struct ieee80211_device *ieee = priv->ieee80211; | |
4272 | ||
4273 | ||
65a43784 | 4274 | return; |
4275 | ||
ecdfa446 GKH |
4276 | // 2007.07.20. If we need to check CCK stop, please uncomment this line. |
4277 | //bStuck = Adapter->HalFunc.CheckHWStopHandler(Adapter); | |
4278 | ||
4279 | if(priv->ResetProgress==RESET_TYPE_NORESET) | |
4280 | { | |
4281 | RESET_START: | |
65a43784 | 4282 | #ifdef ENABLE_LPS |
4283 | //LZM for PS-Poll AID issue. 090429 | |
4284 | if(priv->ieee80211->state == IEEE80211_LINKED) | |
4285 | LeisurePSLeave(dev); | |
4286 | #endif | |
ecdfa446 GKH |
4287 | |
4288 | RT_TRACE(COMP_RESET,"=========>Reset progress!! \n"); | |
4289 | ||
4290 | // Set the variable for reset. | |
4291 | priv->ResetProgress = RESET_TYPE_SILENT; | |
4292 | // rtl8192_close(dev); | |
4293 | #if 1 | |
4294 | down(&priv->wx_sem); | |
4295 | if(priv->up == 0) | |
4296 | { | |
4297 | RT_TRACE(COMP_ERR,"%s():the driver is not up! return\n",__FUNCTION__); | |
4298 | up(&priv->wx_sem); | |
4299 | return ; | |
4300 | } | |
4301 | priv->up = 0; | |
4302 | RT_TRACE(COMP_RESET,"%s():======>start to down the driver\n",__FUNCTION__); | |
4303 | if(!netif_queue_stopped(dev)) | |
4304 | netif_stop_queue(dev); | |
4305 | ||
4306 | dm_backup_dynamic_mechanism_state(dev); | |
4307 | ||
4308 | rtl8192_irq_disable(dev); | |
4309 | rtl8192_cancel_deferred_work(priv); | |
4310 | deinit_hal_dm(dev); | |
4311 | del_timer_sync(&priv->watch_dog_timer); | |
4312 | ieee->sync_scan_hurryup = 1; | |
4313 | if(ieee->state == IEEE80211_LINKED) | |
4314 | { | |
4315 | down(&ieee->wx_sem); | |
4316 | printk("ieee->state is IEEE80211_LINKED\n"); | |
4317 | ieee80211_stop_send_beacons(priv->ieee80211); | |
4318 | del_timer_sync(&ieee->associate_timer); | |
ecdfa446 | 4319 | cancel_delayed_work(&ieee->associate_retry_wq); |
ecdfa446 GKH |
4320 | ieee80211_stop_scan(ieee); |
4321 | netif_carrier_off(dev); | |
4322 | up(&ieee->wx_sem); | |
4323 | } | |
4324 | else{ | |
4325 | printk("ieee->state is NOT LINKED\n"); | |
65a43784 | 4326 | ieee80211_softmac_stop_protocol(priv->ieee80211,true); |
ecdfa446 | 4327 | } |
65a43784 | 4328 | rtl8192_halt_adapter(dev, true); |
ecdfa446 GKH |
4329 | up(&priv->wx_sem); |
4330 | RT_TRACE(COMP_RESET,"%s():<==========down process is finished\n",__FUNCTION__); | |
4331 | RT_TRACE(COMP_RESET,"%s():===========>start to up the driver\n",__FUNCTION__); | |
4332 | reset_status = _rtl8192_up(dev); | |
4333 | ||
4334 | RT_TRACE(COMP_RESET,"%s():<===========up process is finished\n",__FUNCTION__); | |
4335 | if(reset_status == -1) | |
4336 | { | |
4337 | if(reset_times < 3) | |
4338 | { | |
4339 | reset_times++; | |
4340 | goto RESET_START; | |
4341 | } | |
4342 | else | |
4343 | { | |
4344 | RT_TRACE(COMP_ERR," ERR!!! %s(): Reset Failed!!\n",__FUNCTION__); | |
4345 | } | |
4346 | } | |
4347 | #endif | |
4348 | ieee->is_silent_reset = 1; | |
4349 | #if 1 | |
4350 | EnableHWSecurityConfig8192(dev); | |
4351 | #if 1 | |
4352 | if(ieee->state == IEEE80211_LINKED && ieee->iw_mode == IW_MODE_INFRA) | |
4353 | { | |
4354 | ieee->set_chan(ieee->dev, ieee->current_network.channel); | |
4355 | ||
4356 | #if 1 | |
ecdfa446 | 4357 | queue_work(ieee->wq, &ieee->associate_complete_wq); |
ecdfa446 GKH |
4358 | #endif |
4359 | ||
4360 | } | |
4361 | else if(ieee->state == IEEE80211_LINKED && ieee->iw_mode == IW_MODE_ADHOC) | |
4362 | { | |
4363 | ieee->set_chan(ieee->dev, ieee->current_network.channel); | |
4364 | ieee->link_change(ieee->dev); | |
4365 | ||
4366 | // notify_wx_assoc_event(ieee); | |
4367 | ||
4368 | ieee80211_start_send_beacons(ieee); | |
4369 | ||
4370 | if (ieee->data_hard_resume) | |
4371 | ieee->data_hard_resume(ieee->dev); | |
4372 | netif_carrier_on(ieee->dev); | |
4373 | } | |
4374 | #endif | |
4375 | ||
4376 | CamRestoreAllEntry(dev); | |
4377 | ||
4378 | // Restore the previous setting for all dynamic mechanism | |
4379 | dm_restore_dynamic_mechanism_state(dev); | |
4380 | ||
4381 | priv->ResetProgress = RESET_TYPE_NORESET; | |
4382 | priv->reset_count++; | |
4383 | ||
4384 | priv->bForcedSilentReset =false; | |
4385 | priv->bResetInProgress = false; | |
4386 | ||
4387 | // For test --> force write UFWP. | |
4388 | write_nic_byte(dev, UFWP, 1); | |
4389 | RT_TRACE(COMP_RESET, "Reset finished!! ====>[%d]\n", priv->reset_count); | |
4390 | #endif | |
4391 | } | |
4392 | } | |
4393 | ||
4394 | #ifdef ENABLE_IPS | |
4395 | void InactivePsWorkItemCallback(struct net_device *dev) | |
4396 | { | |
4397 | struct r8192_priv *priv = ieee80211_priv(dev); | |
4398 | PRT_POWER_SAVE_CONTROL pPSC = (PRT_POWER_SAVE_CONTROL)(&(priv->ieee80211->PowerSaveControl)); | |
4399 | //u8 index = 0; | |
4400 | ||
4401 | RT_TRACE(COMP_POWER, "InactivePsWorkItemCallback() ---------> \n"); | |
4402 | // | |
4403 | // This flag "bSwRfProcessing", indicates the status of IPS procedure, should be set if the IPS workitem | |
4404 | // is really scheduled. | |
4405 | // The old code, sets this flag before scheduling the IPS workitem and however, at the same time the | |
4406 | // previous IPS workitem did not end yet, fails to schedule the current workitem. Thus, bSwRfProcessing | |
4407 | // blocks the IPS procedure of switching RF. | |
4408 | // By Bruce, 2007-12-25. | |
4409 | // | |
4410 | pPSC->bSwRfProcessing = TRUE; | |
4411 | ||
4412 | RT_TRACE(COMP_RF, "InactivePsWorkItemCallback(): Set RF to %s.\n", \ | |
4413 | pPSC->eInactivePowerState == eRfOff?"OFF":"ON"); | |
4414 | ||
4415 | ||
4416 | MgntActSet_RF_State(dev, pPSC->eInactivePowerState, RF_CHANGE_BY_IPS); | |
4417 | ||
4418 | // | |
4419 | // To solve CAM values miss in RF OFF, rewrite CAM values after RF ON. By Bruce, 2007-09-20. | |
4420 | // | |
ecdfa446 GKH |
4421 | pPSC->bSwRfProcessing = FALSE; |
4422 | RT_TRACE(COMP_POWER, "InactivePsWorkItemCallback() <--------- \n"); | |
4423 | } | |
4424 | ||
65a43784 | 4425 | #ifdef ENABLE_LPS |
4426 | // | |
4427 | // Change current and default preamble mode. | |
4428 | // 2005.01.06, by rcnjko. | |
4429 | // | |
4430 | bool MgntActSet_802_11_PowerSaveMode(struct net_device *dev, u8 rtPsMode) | |
4431 | { | |
4432 | struct r8192_priv *priv = ieee80211_priv(dev); | |
4433 | //PRT_POWER_SAVE_CONTROL pPSC = (PRT_POWER_SAVE_CONTROL)(&(priv->ieee80211->PowerSaveControl)); | |
4434 | //u8 RpwmVal, FwPwrMode; | |
4435 | ||
4436 | // Currently, we do not change power save mode on IBSS mode. | |
4437 | if(priv->ieee80211->iw_mode == IW_MODE_ADHOC) | |
4438 | { | |
4439 | return false; | |
4440 | } | |
4441 | ||
4442 | // | |
4443 | // <RJ_NOTE> If we make HW to fill up the PwrMgt bit for us, | |
4444 | // some AP will not response to our mgnt frames with PwrMgt bit set, | |
4445 | // e.g. cannot associate the AP. | |
4446 | // So I commented out it. 2005.02.16, by rcnjko. | |
4447 | // | |
4448 | // // Change device's power save mode. | |
4449 | // Adapter->HalFunc.SetPSModeHandler( Adapter, rtPsMode ); | |
4450 | ||
4451 | // Update power save mode configured. | |
4452 | //RT_TRACE(COMP_LPS,"%s(): set ieee->ps = %x\n",__FUNCTION__,rtPsMode); | |
4453 | if(!priv->ps_force) { | |
4454 | priv->ieee80211->ps = rtPsMode; | |
4455 | } | |
4456 | ||
4457 | // Awake immediately | |
4458 | if(priv->ieee80211->sta_sleep != 0 && rtPsMode == IEEE80211_PS_DISABLED) | |
4459 | { | |
4460 | unsigned long flags; | |
4461 | ||
4462 | //PlatformSetTimer(Adapter, &(pMgntInfo->AwakeTimer), 0); | |
4463 | // Notify the AP we awke. | |
4464 | rtl8192_hw_wakeup(dev); | |
4465 | priv->ieee80211->sta_sleep = 0; | |
4466 | ||
4467 | spin_lock_irqsave(&(priv->ieee80211->mgmt_tx_lock), flags); | |
4468 | printk("LPS leave: notify AP we are awaked ++++++++++ SendNullFunctionData\n"); | |
4469 | ieee80211_sta_ps_send_null_frame(priv->ieee80211, 0); | |
4470 | spin_unlock_irqrestore(&(priv->ieee80211->mgmt_tx_lock), flags); | |
4471 | } | |
4472 | ||
4473 | return true; | |
4474 | } | |
4475 | ||
4476 | //================================================================================ | |
4477 | // Leisure Power Save in linked state. | |
4478 | //================================================================================ | |
4479 | ||
4480 | // | |
4481 | // Description: | |
4482 | // Enter the leisure power save mode. | |
4483 | // | |
4484 | void LeisurePSEnter(struct net_device *dev) | |
4485 | { | |
4486 | struct r8192_priv *priv = ieee80211_priv(dev); | |
4487 | PRT_POWER_SAVE_CONTROL pPSC = (PRT_POWER_SAVE_CONTROL)(&(priv->ieee80211->PowerSaveControl)); | |
4488 | ||
4489 | //RT_TRACE(COMP_PS, "LeisurePSEnter()...\n"); | |
4490 | //RT_TRACE(COMP_PS, "pPSC->bLeisurePs = %d, ieee->ps = %d,pPSC->LpsIdleCount is %d,RT_CHECK_FOR_HANG_PERIOD is %d\n", | |
4491 | // pPSC->bLeisurePs, priv->ieee80211->ps,pPSC->LpsIdleCount,RT_CHECK_FOR_HANG_PERIOD); | |
4492 | ||
4493 | if(!((priv->ieee80211->iw_mode == IW_MODE_INFRA) && | |
4494 | (priv->ieee80211->state == IEEE80211_LINKED)) || | |
4495 | (priv->ieee80211->iw_mode == IW_MODE_ADHOC) || | |
4496 | (priv->ieee80211->iw_mode == IW_MODE_MASTER)) | |
4497 | return; | |
4498 | ||
4499 | if (pPSC->bLeisurePs) | |
4500 | { | |
4501 | // Idle for a while if we connect to AP a while ago. | |
4502 | if(pPSC->LpsIdleCount >= RT_CHECK_FOR_HANG_PERIOD) // 4 Sec | |
4503 | { | |
4504 | ||
4505 | if(priv->ieee80211->ps == IEEE80211_PS_DISABLED) | |
4506 | { | |
4507 | ||
4508 | //RT_TRACE(COMP_LPS, "LeisurePSEnter(): Enter 802.11 power save mode...\n"); | |
4509 | MgntActSet_802_11_PowerSaveMode(dev, IEEE80211_PS_MBCAST|IEEE80211_PS_UNICAST); | |
4510 | ||
4511 | } | |
4512 | } | |
4513 | else | |
4514 | pPSC->LpsIdleCount++; | |
4515 | } | |
4516 | } | |
4517 | ||
4518 | ||
4519 | // | |
4520 | // Description: | |
4521 | // Leave the leisure power save mode. | |
4522 | // | |
4523 | void LeisurePSLeave(struct net_device *dev) | |
4524 | { | |
4525 | struct r8192_priv *priv = ieee80211_priv(dev); | |
4526 | PRT_POWER_SAVE_CONTROL pPSC = (PRT_POWER_SAVE_CONTROL)(&(priv->ieee80211->PowerSaveControl)); | |
4527 | ||
4528 | ||
4529 | //RT_TRACE(COMP_PS, "LeisurePSLeave()...\n"); | |
4530 | //RT_TRACE(COMP_PS, "pPSC->bLeisurePs = %d, ieee->ps = %d\n", | |
4531 | // pPSC->bLeisurePs, priv->ieee80211->ps); | |
4532 | ||
4533 | if (pPSC->bLeisurePs) | |
4534 | { | |
4535 | if(priv->ieee80211->ps != IEEE80211_PS_DISABLED) | |
4536 | { | |
4537 | // move to lps_wakecomplete() | |
4538 | //RT_TRACE(COMP_LPS, "LeisurePSLeave(): Busy Traffic , Leave 802.11 power save..\n"); | |
4539 | MgntActSet_802_11_PowerSaveMode(dev, IEEE80211_PS_DISABLED); | |
4540 | ||
4541 | } | |
4542 | } | |
4543 | } | |
4544 | #endif | |
4545 | ||
4546 | ||
ecdfa446 GKH |
4547 | // |
4548 | // Description: | |
4549 | // Enter the inactive power save mode. RF will be off | |
4550 | // 2007.08.17, by shien chang. | |
4551 | // | |
4552 | void | |
4553 | IPSEnter(struct net_device *dev) | |
4554 | { | |
4555 | struct r8192_priv *priv = ieee80211_priv(dev); | |
4556 | PRT_POWER_SAVE_CONTROL pPSC = (PRT_POWER_SAVE_CONTROL)(&(priv->ieee80211->PowerSaveControl)); | |
4557 | RT_RF_POWER_STATE rtState; | |
4558 | ||
4559 | if (pPSC->bInactivePs) | |
4560 | { | |
4561 | rtState = priv->ieee80211->eRFPowerState; | |
4562 | // | |
4563 | // Added by Bruce, 2007-12-25. | |
4564 | // Do not enter IPS in the following conditions: | |
4565 | // (1) RF is already OFF or Sleep | |
4566 | // (2) bSwRfProcessing (indicates the IPS is still under going) | |
4567 | // (3) Connectted (only disconnected can trigger IPS) | |
4568 | // (4) IBSS (send Beacon) | |
4569 | // (5) AP mode (send Beacon) | |
4570 | // | |
4571 | if (rtState == eRfOn && !pPSC->bSwRfProcessing | |
4572 | && (priv->ieee80211->state != IEEE80211_LINKED) ) | |
4573 | { | |
4574 | RT_TRACE(COMP_RF,"IPSEnter(): Turn off RF.\n"); | |
65a43784 | 4575 | //printk("IPSEnter(): Turn off RF.\n"); |
ecdfa446 GKH |
4576 | pPSC->eInactivePowerState = eRfOff; |
4577 | // queue_work(priv->priv_wq,&(pPSC->InactivePsWorkItem)); | |
4578 | InactivePsWorkItemCallback(dev); | |
4579 | } | |
4580 | } | |
4581 | } | |
4582 | ||
4583 | // | |
4584 | // Description: | |
4585 | // Leave the inactive power save mode, RF will be on. | |
4586 | // 2007.08.17, by shien chang. | |
4587 | // | |
4588 | void | |
4589 | IPSLeave(struct net_device *dev) | |
4590 | { | |
4591 | struct r8192_priv *priv = ieee80211_priv(dev); | |
4592 | PRT_POWER_SAVE_CONTROL pPSC = (PRT_POWER_SAVE_CONTROL)(&(priv->ieee80211->PowerSaveControl)); | |
4593 | RT_RF_POWER_STATE rtState; | |
4594 | ||
4595 | if (pPSC->bInactivePs) | |
4596 | { | |
4597 | rtState = priv->ieee80211->eRFPowerState; | |
4598 | if (rtState != eRfOn && !pPSC->bSwRfProcessing && priv->ieee80211->RfOffReason <= RF_CHANGE_BY_IPS) | |
4599 | { | |
4600 | RT_TRACE(COMP_POWER, "IPSLeave(): Turn on RF.\n"); | |
65a43784 | 4601 | //printk("IPSLeave(): Turn on RF.\n"); |
ecdfa446 GKH |
4602 | pPSC->eInactivePowerState = eRfOn; |
4603 | // queue_work(priv->priv_wq,&(pPSC->InactivePsWorkItem)); | |
4604 | InactivePsWorkItemCallback(dev); | |
4605 | } | |
4606 | } | |
4607 | } | |
65a43784 | 4608 | |
4609 | void IPSLeave_wq(void *data) | |
4610 | { | |
4611 | struct ieee80211_device *ieee = container_of(data,struct ieee80211_device,ips_leave_wq); | |
4612 | struct net_device *dev = ieee->dev; | |
4613 | ||
4614 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
4615 | down(&priv->ieee80211->ips_sem); | |
4616 | IPSLeave(dev); | |
4617 | up(&priv->ieee80211->ips_sem); | |
4618 | } | |
4619 | ||
4620 | void ieee80211_ips_leave_wq(struct net_device *dev) | |
4621 | { | |
4622 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
4623 | RT_RF_POWER_STATE rtState; | |
4624 | rtState = priv->ieee80211->eRFPowerState; | |
4625 | ||
4626 | if(priv->ieee80211->PowerSaveControl.bInactivePs){ | |
4627 | if(rtState == eRfOff){ | |
4628 | if(priv->ieee80211->RfOffReason > RF_CHANGE_BY_IPS) | |
4629 | { | |
4630 | RT_TRACE(COMP_ERR, "%s(): RF is OFF.\n",__FUNCTION__); | |
4631 | return; | |
4632 | } | |
4633 | else{ | |
4634 | printk("=========>%s(): IPSLeave\n",__FUNCTION__); | |
4635 | queue_work(priv->ieee80211->wq,&priv->ieee80211->ips_leave_wq); | |
4636 | } | |
4637 | } | |
4638 | } | |
4639 | } | |
4640 | //added by amy 090331 end | |
4641 | void ieee80211_ips_leave(struct net_device *dev) | |
4642 | { | |
4643 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
4644 | down(&priv->ieee80211->ips_sem); | |
4645 | IPSLeave(dev); | |
4646 | up(&priv->ieee80211->ips_sem); | |
4647 | } | |
ecdfa446 | 4648 | #endif |
ecdfa446 | 4649 | |
5e1ad18a | 4650 | static void rtl819x_update_rxcounts( |
ecdfa446 GKH |
4651 | struct r8192_priv *priv, |
4652 | u32* TotalRxBcnNum, | |
4653 | u32* TotalRxDataNum | |
4654 | ) | |
4655 | { | |
4656 | u16 SlotIndex; | |
4657 | u8 i; | |
4658 | ||
4659 | *TotalRxBcnNum = 0; | |
4660 | *TotalRxDataNum = 0; | |
4661 | ||
4662 | SlotIndex = (priv->ieee80211->LinkDetectInfo.SlotIndex++)%(priv->ieee80211->LinkDetectInfo.SlotNum); | |
4663 | priv->ieee80211->LinkDetectInfo.RxBcnNum[SlotIndex] = priv->ieee80211->LinkDetectInfo.NumRecvBcnInPeriod; | |
4664 | priv->ieee80211->LinkDetectInfo.RxDataNum[SlotIndex] = priv->ieee80211->LinkDetectInfo.NumRecvDataInPeriod; | |
4665 | for( i=0; i<priv->ieee80211->LinkDetectInfo.SlotNum; i++ ){ | |
4666 | *TotalRxBcnNum += priv->ieee80211->LinkDetectInfo.RxBcnNum[i]; | |
4667 | *TotalRxDataNum += priv->ieee80211->LinkDetectInfo.RxDataNum[i]; | |
4668 | } | |
4669 | } | |
4670 | ||
4671 | ||
5e1ad18a | 4672 | void rtl819x_watchdog_wqcallback(struct work_struct *work) |
ecdfa446 GKH |
4673 | { |
4674 | struct delayed_work *dwork = container_of(work,struct delayed_work,work); | |
4675 | struct r8192_priv *priv = container_of(dwork,struct r8192_priv,watch_dog_wq); | |
4676 | struct net_device *dev = priv->ieee80211->dev; | |
ecdfa446 GKH |
4677 | struct ieee80211_device* ieee = priv->ieee80211; |
4678 | RESET_TYPE ResetType = RESET_TYPE_NORESET; | |
4679 | static u8 check_reset_cnt=0; | |
4680 | unsigned long flags; | |
4681 | bool bBusyTraffic = false; | |
4682 | static u8 last_time = 0; | |
65a43784 | 4683 | bool bEnterPS = false; |
4684 | ||
4685 | if((!priv->up) || (priv->bHwRadioOff == true)) | |
4686 | return; | |
4687 | ||
ecdfa446 GKH |
4688 | if(!priv->up) |
4689 | return; | |
4690 | hal_dm_watchdog(dev); | |
4691 | #ifdef ENABLE_IPS | |
4692 | // printk("watch_dog ENABLE_IPS\n"); | |
4693 | if(ieee->actscanning == false){ | |
65a43784 | 4694 | //printk("%d,%d,%d,%d\n", ieee->eRFPowerState, ieee->is_set_key, ieee->proto_stoppping, ieee->wx_set_enc); |
4695 | if((ieee->iw_mode == IW_MODE_INFRA) && (ieee->state == IEEE80211_NOLINK) &&\ | |
4696 | (ieee->eRFPowerState == eRfOn)&&!ieee->is_set_key &&\ | |
4697 | (!ieee->proto_stoppping) && !ieee->wx_set_enc){ | |
ecdfa446 | 4698 | if(ieee->PowerSaveControl.ReturnPoint == IPS_CALLBACK_NONE){ |
65a43784 | 4699 | //printk("====================>haha:IPSEnter()\n"); |
ecdfa446 GKH |
4700 | IPSEnter(dev); |
4701 | //ieee80211_stop_scan(priv->ieee80211); | |
4702 | } | |
4703 | } | |
4704 | } | |
4705 | #endif | |
4706 | {//to get busy traffic condition | |
4707 | if(ieee->state == IEEE80211_LINKED) | |
4708 | { | |
65a43784 | 4709 | if( ieee->LinkDetectInfo.NumRxOkInPeriod> 100 || |
4710 | ieee->LinkDetectInfo.NumTxOkInPeriod> 100 ) { | |
ecdfa446 GKH |
4711 | bBusyTraffic = true; |
4712 | } | |
4713 | ||
65a43784 | 4714 | #ifdef ENABLE_LPS |
4715 | //added by amy for Leisure PS | |
4716 | if( ((ieee->LinkDetectInfo.NumRxUnicastOkInPeriod + ieee->LinkDetectInfo.NumTxOkInPeriod) > 8 ) || | |
4717 | (ieee->LinkDetectInfo.NumRxUnicastOkInPeriod > 2) ) | |
4718 | { | |
4719 | //printk("ieee->LinkDetectInfo.NumRxUnicastOkInPeriod is %d,ieee->LinkDetectInfo.NumTxOkInPeriod is %d\n", | |
4720 | // ieee->LinkDetectInfo.NumRxUnicastOkInPeriod,ieee->LinkDetectInfo.NumTxOkInPeriod); | |
4721 | bEnterPS= false; | |
4722 | } | |
4723 | else | |
4724 | { | |
4725 | bEnterPS= true; | |
4726 | } | |
4727 | ||
4728 | //printk("***bEnterPS = %d\n", bEnterPS); | |
4729 | // LeisurePS only work in infra mode. | |
4730 | if(bEnterPS) | |
4731 | { | |
4732 | LeisurePSEnter(dev); | |
4733 | } | |
4734 | else | |
4735 | { | |
4736 | LeisurePSLeave(dev); | |
4737 | } | |
4738 | #endif | |
4739 | ||
4740 | } | |
4741 | else | |
4742 | { | |
4743 | #ifdef ENABLE_LPS | |
4744 | //RT_TRACE(COMP_LPS,"====>no link LPS leave\n"); | |
4745 | LeisurePSLeave(dev); | |
4746 | #endif | |
ecdfa446 | 4747 | } |
65a43784 | 4748 | |
ecdfa446 GKH |
4749 | ieee->LinkDetectInfo.NumRxOkInPeriod = 0; |
4750 | ieee->LinkDetectInfo.NumTxOkInPeriod = 0; | |
65a43784 | 4751 | ieee->LinkDetectInfo.NumRxUnicastOkInPeriod = 0; |
ecdfa446 GKH |
4752 | ieee->LinkDetectInfo.bBusyTraffic = bBusyTraffic; |
4753 | } | |
4754 | ||
4755 | ||
4756 | //added by amy for AP roaming | |
4757 | if (1) | |
4758 | { | |
4759 | if(ieee->state == IEEE80211_LINKED && ieee->iw_mode == IW_MODE_INFRA) | |
4760 | { | |
4761 | u32 TotalRxBcnNum = 0; | |
4762 | u32 TotalRxDataNum = 0; | |
4763 | ||
4764 | rtl819x_update_rxcounts(priv, &TotalRxBcnNum, &TotalRxDataNum); | |
4765 | if((TotalRxBcnNum+TotalRxDataNum) == 0) | |
4766 | { | |
4767 | if( ieee->eRFPowerState == eRfOff) | |
4768 | RT_TRACE(COMP_ERR,"========>%s()\n",__FUNCTION__); | |
4769 | printk("===>%s(): AP is power off,connect another one\n",__FUNCTION__); | |
65a43784 | 4770 | // Dot11d_Reset(dev); |
ecdfa446 GKH |
4771 | ieee->state = IEEE80211_ASSOCIATING; |
4772 | notify_wx_assoc_event(priv->ieee80211); | |
65a43784 | 4773 | RemovePeerTS(priv->ieee80211,priv->ieee80211->current_network.bssid); |
ecdfa446 GKH |
4774 | ieee->is_roaming = true; |
4775 | ieee->is_set_key = false; | |
65a43784 | 4776 | ieee->link_change(dev); |
4777 | queue_work(ieee->wq, &ieee->associate_procedure_wq); | |
ecdfa446 GKH |
4778 | } |
4779 | } | |
4780 | ieee->LinkDetectInfo.NumRecvBcnInPeriod=0; | |
4781 | ieee->LinkDetectInfo.NumRecvDataInPeriod=0; | |
4782 | ||
4783 | } | |
ecdfa446 GKH |
4784 | //check if reset the driver |
4785 | spin_lock_irqsave(&priv->tx_lock,flags); | |
4786 | if(check_reset_cnt++ >= 3 && !ieee->is_roaming && (last_time != 1)) | |
4787 | { | |
4788 | ResetType = rtl819x_ifcheck_resetornot(dev); | |
4789 | check_reset_cnt = 3; | |
4790 | //DbgPrint("Start to check silent reset\n"); | |
4791 | } | |
4792 | spin_unlock_irqrestore(&priv->tx_lock,flags); | |
4793 | if(!priv->bDisableNormalResetCheck && ResetType == RESET_TYPE_NORMAL) | |
4794 | { | |
4795 | priv->ResetProgress = RESET_TYPE_NORMAL; | |
4796 | RT_TRACE(COMP_RESET,"%s(): NOMAL RESET\n",__FUNCTION__); | |
4797 | return; | |
4798 | } | |
4799 | /* disable silent reset temply 2008.9.11*/ | |
4800 | #if 1 | |
4801 | if( ((priv->force_reset) || (!priv->bDisableNormalResetCheck && ResetType==RESET_TYPE_SILENT))) // This is control by OID set in Pomelo | |
4802 | { | |
4803 | last_time = 1; | |
4804 | rtl819x_ifsilentreset(dev); | |
4805 | } | |
4806 | else | |
4807 | last_time = 0; | |
4808 | #endif | |
4809 | priv->force_reset = false; | |
4810 | priv->bForcedSilentReset = false; | |
4811 | priv->bResetInProgress = false; | |
4812 | RT_TRACE(COMP_TRACE, " <==RtUsbCheckForHangWorkItemCallback()\n"); | |
4813 | ||
4814 | } | |
4815 | ||
4816 | void watch_dog_timer_callback(unsigned long data) | |
4817 | { | |
4818 | struct r8192_priv *priv = ieee80211_priv((struct net_device *) data); | |
ecdfa446 | 4819 | queue_delayed_work(priv->priv_wq,&priv->watch_dog_wq,0); |
ecdfa446 GKH |
4820 | mod_timer(&priv->watch_dog_timer, jiffies + MSECS(IEEE80211_WATCH_DOG_TIME)); |
4821 | ||
4822 | } | |
4823 | int _rtl8192_up(struct net_device *dev) | |
4824 | { | |
4825 | struct r8192_priv *priv = ieee80211_priv(dev); | |
4826 | //int i; | |
4827 | RT_STATUS init_status = RT_STATUS_SUCCESS; | |
4828 | priv->up=1; | |
4829 | priv->ieee80211->ieee_up=1; | |
65a43784 | 4830 | priv->bdisable_nic = false; //YJ,add,091111 |
ecdfa446 GKH |
4831 | RT_TRACE(COMP_INIT, "Bringing up iface"); |
4832 | ||
4833 | init_status = rtl8192_adapter_start(dev); | |
4834 | if(init_status != RT_STATUS_SUCCESS) | |
4835 | { | |
4836 | RT_TRACE(COMP_ERR,"ERR!!! %s(): initialization is failed!\n",__FUNCTION__); | |
4837 | return -1; | |
4838 | } | |
4839 | RT_TRACE(COMP_INIT, "start adapter finished\n"); | |
4840 | #ifdef RTL8192E | |
4841 | if(priv->ieee80211->eRFPowerState!=eRfOn) | |
4842 | MgntActSet_RF_State(dev, eRfOn, priv->ieee80211->RfOffReason); | |
4843 | #endif | |
4844 | if(priv->ieee80211->state != IEEE80211_LINKED) | |
4845 | ieee80211_softmac_start_protocol(priv->ieee80211); | |
4846 | ieee80211_reset_queue(priv->ieee80211); | |
4847 | watch_dog_timer_callback((unsigned long) dev); | |
4848 | if(!netif_queue_stopped(dev)) | |
4849 | netif_start_queue(dev); | |
4850 | else | |
4851 | netif_wake_queue(dev); | |
4852 | ||
4853 | return 0; | |
4854 | } | |
4855 | ||
4856 | ||
5e1ad18a | 4857 | static int rtl8192_open(struct net_device *dev) |
ecdfa446 GKH |
4858 | { |
4859 | struct r8192_priv *priv = ieee80211_priv(dev); | |
4860 | int ret; | |
4861 | ||
4862 | down(&priv->wx_sem); | |
4863 | ret = rtl8192_up(dev); | |
4864 | up(&priv->wx_sem); | |
4865 | return ret; | |
4866 | ||
4867 | } | |
4868 | ||
4869 | ||
4870 | int rtl8192_up(struct net_device *dev) | |
4871 | { | |
4872 | struct r8192_priv *priv = ieee80211_priv(dev); | |
4873 | ||
4874 | if (priv->up == 1) return -1; | |
4875 | ||
4876 | return _rtl8192_up(dev); | |
4877 | } | |
4878 | ||
4879 | ||
5e1ad18a | 4880 | static int rtl8192_close(struct net_device *dev) |
ecdfa446 GKH |
4881 | { |
4882 | struct r8192_priv *priv = ieee80211_priv(dev); | |
4883 | int ret; | |
4884 | ||
4885 | down(&priv->wx_sem); | |
4886 | ||
4887 | ret = rtl8192_down(dev); | |
4888 | ||
4889 | up(&priv->wx_sem); | |
4890 | ||
4891 | return ret; | |
4892 | ||
4893 | } | |
4894 | ||
4895 | int rtl8192_down(struct net_device *dev) | |
4896 | { | |
4897 | struct r8192_priv *priv = ieee80211_priv(dev); | |
4898 | // int i; | |
4899 | #if 0 | |
4900 | u8 ucRegRead; | |
4901 | u32 ulRegRead; | |
4902 | #endif | |
4903 | if (priv->up == 0) return -1; | |
4904 | ||
65a43784 | 4905 | #ifdef ENABLE_LPS |
4906 | //LZM for PS-Poll AID issue. 090429 | |
4907 | if(priv->ieee80211->state == IEEE80211_LINKED) | |
4908 | LeisurePSLeave(dev); | |
4909 | #endif | |
4910 | ||
ecdfa446 GKH |
4911 | priv->up=0; |
4912 | priv->ieee80211->ieee_up = 0; | |
4913 | RT_TRACE(COMP_DOWN, "==========>%s()\n", __FUNCTION__); | |
4914 | /* FIXME */ | |
4915 | if (!netif_queue_stopped(dev)) | |
4916 | netif_stop_queue(dev); | |
4917 | ||
4918 | rtl8192_irq_disable(dev); | |
4919 | #if 0 | |
4920 | if(!priv->ieee80211->bSupportRemoteWakeUp) { | |
4921 | MgntActSet_RF_State(dev, eRfOff, RF_CHANGE_BY_INIT); | |
4922 | // 2006.11.30. System reset bit | |
4923 | ulRegRead = read_nic_dword(dev, CPU_GEN); | |
4924 | ulRegRead|=CPU_GEN_SYSTEM_RESET; | |
4925 | write_nic_dword(dev, CPU_GEN, ulRegRead); | |
4926 | } else { | |
4927 | //2008.06.03 for WOL | |
4928 | write_nic_dword(dev, WFCRC0, 0xffffffff); | |
4929 | write_nic_dword(dev, WFCRC1, 0xffffffff); | |
4930 | write_nic_dword(dev, WFCRC2, 0xffffffff); | |
4931 | #ifdef RTL8190P | |
4932 | //GPIO 0 = TRUE | |
4933 | ucRegRead = read_nic_byte(dev, GPO); | |
4934 | ucRegRead |= BIT0; | |
4935 | write_nic_byte(dev, GPO, ucRegRead); | |
4936 | #endif | |
4937 | //Write PMR register | |
4938 | write_nic_byte(dev, PMR, 0x5); | |
4939 | //Disable tx, enanble rx | |
4940 | write_nic_byte(dev, MacBlkCtrl, 0xa); | |
4941 | } | |
4942 | #endif | |
4943 | // flush_scheduled_work(); | |
4944 | rtl8192_cancel_deferred_work(priv); | |
4945 | deinit_hal_dm(dev); | |
4946 | del_timer_sync(&priv->watch_dog_timer); | |
4947 | ||
65a43784 | 4948 | ieee80211_softmac_stop_protocol(priv->ieee80211,true); |
4949 | ||
4950 | rtl8192_halt_adapter(dev,false); | |
ecdfa446 GKH |
4951 | memset(&priv->ieee80211->current_network, 0 , offsetof(struct ieee80211_network, list)); |
4952 | ||
4953 | RT_TRACE(COMP_DOWN, "<==========%s()\n", __FUNCTION__); | |
4954 | ||
4955 | return 0; | |
4956 | } | |
4957 | ||
4958 | ||
4959 | void rtl8192_commit(struct net_device *dev) | |
4960 | { | |
4961 | struct r8192_priv *priv = ieee80211_priv(dev); | |
4962 | ||
4963 | if (priv->up == 0) return ; | |
4964 | ||
4965 | ||
65a43784 | 4966 | ieee80211_softmac_stop_protocol(priv->ieee80211,true); |
ecdfa446 GKH |
4967 | |
4968 | rtl8192_irq_disable(dev); | |
65a43784 | 4969 | rtl8192_halt_adapter(dev,true); |
ecdfa446 GKH |
4970 | _rtl8192_up(dev); |
4971 | } | |
4972 | ||
ecdfa446 GKH |
4973 | void rtl8192_restart(struct work_struct *work) |
4974 | { | |
4975 | struct r8192_priv *priv = container_of(work, struct r8192_priv, reset_wq); | |
4976 | struct net_device *dev = priv->ieee80211->dev; | |
ecdfa446 GKH |
4977 | |
4978 | down(&priv->wx_sem); | |
4979 | ||
4980 | rtl8192_commit(dev); | |
4981 | ||
4982 | up(&priv->wx_sem); | |
4983 | } | |
4984 | ||
4985 | static void r8192_set_multicast(struct net_device *dev) | |
4986 | { | |
4987 | struct r8192_priv *priv = ieee80211_priv(dev); | |
4988 | short promisc; | |
4989 | ||
4990 | //down(&priv->wx_sem); | |
4991 | ||
4992 | /* FIXME FIXME */ | |
4993 | ||
4994 | promisc = (dev->flags & IFF_PROMISC) ? 1:0; | |
4995 | ||
4996 | if (promisc != priv->promisc) { | |
4997 | ; | |
4998 | // rtl8192_commit(dev); | |
4999 | } | |
5000 | ||
5001 | priv->promisc = promisc; | |
5002 | ||
5003 | //schedule_work(&priv->reset_wq); | |
5004 | //up(&priv->wx_sem); | |
5005 | } | |
5006 | ||
5007 | ||
5e1ad18a | 5008 | static int r8192_set_mac_adr(struct net_device *dev, void *mac) |
ecdfa446 GKH |
5009 | { |
5010 | struct r8192_priv *priv = ieee80211_priv(dev); | |
5011 | struct sockaddr *addr = mac; | |
5012 | ||
5013 | down(&priv->wx_sem); | |
5014 | ||
5015 | memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN); | |
5016 | ||
ecdfa446 | 5017 | schedule_work(&priv->reset_wq); |
ecdfa446 GKH |
5018 | up(&priv->wx_sem); |
5019 | ||
5020 | return 0; | |
5021 | } | |
5022 | ||
5023 | /* based on ipw2200 driver */ | |
5e1ad18a | 5024 | static int rtl8192_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) |
ecdfa446 GKH |
5025 | { |
5026 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
5027 | struct iwreq *wrq = (struct iwreq *)rq; | |
5028 | int ret=-1; | |
5029 | struct ieee80211_device *ieee = priv->ieee80211; | |
5030 | u32 key[4]; | |
5031 | u8 broadcast_addr[6] = {0xff,0xff,0xff,0xff,0xff,0xff}; | |
5032 | struct iw_point *p = &wrq->u.data; | |
5033 | struct ieee_param *ipw = NULL;//(struct ieee_param *)wrq->u.data.pointer; | |
5034 | ||
5035 | down(&priv->wx_sem); | |
5036 | ||
5037 | ||
5038 | if (p->length < sizeof(struct ieee_param) || !p->pointer){ | |
5039 | ret = -EINVAL; | |
5040 | goto out; | |
5041 | } | |
5042 | ||
5043 | ipw = (struct ieee_param *)kmalloc(p->length, GFP_KERNEL); | |
5044 | if (ipw == NULL){ | |
5045 | ret = -ENOMEM; | |
5046 | goto out; | |
5047 | } | |
5048 | if (copy_from_user(ipw, p->pointer, p->length)) { | |
5049 | kfree(ipw); | |
5050 | ret = -EFAULT; | |
5051 | goto out; | |
5052 | } | |
5053 | ||
5054 | switch (cmd) { | |
5055 | case RTL_IOCTL_WPA_SUPPLICANT: | |
5056 | //parse here for HW security | |
5057 | if (ipw->cmd == IEEE_CMD_SET_ENCRYPTION) | |
5058 | { | |
5059 | if (ipw->u.crypt.set_tx) | |
5060 | { | |
5061 | if (strcmp(ipw->u.crypt.alg, "CCMP") == 0) | |
5062 | ieee->pairwise_key_type = KEY_TYPE_CCMP; | |
5063 | else if (strcmp(ipw->u.crypt.alg, "TKIP") == 0) | |
5064 | ieee->pairwise_key_type = KEY_TYPE_TKIP; | |
5065 | else if (strcmp(ipw->u.crypt.alg, "WEP") == 0) | |
5066 | { | |
5067 | if (ipw->u.crypt.key_len == 13) | |
5068 | ieee->pairwise_key_type = KEY_TYPE_WEP104; | |
5069 | else if (ipw->u.crypt.key_len == 5) | |
5070 | ieee->pairwise_key_type = KEY_TYPE_WEP40; | |
5071 | } | |
5072 | else | |
5073 | ieee->pairwise_key_type = KEY_TYPE_NA; | |
5074 | ||
5075 | if (ieee->pairwise_key_type) | |
5076 | { | |
5077 | memcpy((u8*)key, ipw->u.crypt.key, 16); | |
5078 | EnableHWSecurityConfig8192(dev); | |
5079 | //we fill both index entry and 4th entry for pairwise key as in IPW interface, adhoc will only get here, so we need index entry for its default key serching! | |
5080 | //added by WB. | |
5081 | setKey(dev, 4, ipw->u.crypt.idx, ieee->pairwise_key_type, (u8*)ieee->ap_mac_addr, 0, key); | |
5082 | if (ieee->auth_mode != 2) //LEAP WEP will never set this. | |
5083 | setKey(dev, ipw->u.crypt.idx, ipw->u.crypt.idx, ieee->pairwise_key_type, (u8*)ieee->ap_mac_addr, 0, key); | |
5084 | } | |
5085 | if ((ieee->pairwise_key_type == KEY_TYPE_CCMP) && ieee->pHTInfo->bCurrentHTSupport){ | |
5086 | write_nic_byte(dev, 0x173, 1); //fix aes bug | |
5087 | } | |
5088 | ||
5089 | } | |
5090 | else //if (ipw->u.crypt.idx) //group key use idx > 0 | |
5091 | { | |
5092 | memcpy((u8*)key, ipw->u.crypt.key, 16); | |
5093 | if (strcmp(ipw->u.crypt.alg, "CCMP") == 0) | |
5094 | ieee->group_key_type= KEY_TYPE_CCMP; | |
5095 | else if (strcmp(ipw->u.crypt.alg, "TKIP") == 0) | |
5096 | ieee->group_key_type = KEY_TYPE_TKIP; | |
5097 | else if (strcmp(ipw->u.crypt.alg, "WEP") == 0) | |
5098 | { | |
5099 | if (ipw->u.crypt.key_len == 13) | |
5100 | ieee->group_key_type = KEY_TYPE_WEP104; | |
5101 | else if (ipw->u.crypt.key_len == 5) | |
5102 | ieee->group_key_type = KEY_TYPE_WEP40; | |
5103 | } | |
5104 | else | |
5105 | ieee->group_key_type = KEY_TYPE_NA; | |
5106 | ||
5107 | if (ieee->group_key_type) | |
5108 | { | |
5109 | setKey( dev, | |
5110 | ipw->u.crypt.idx, | |
5111 | ipw->u.crypt.idx, //KeyIndex | |
5112 | ieee->group_key_type, //KeyType | |
5113 | broadcast_addr, //MacAddr | |
5114 | 0, //DefaultKey | |
5115 | key); //KeyContent | |
5116 | } | |
5117 | } | |
5118 | } | |
5119 | #ifdef JOHN_DEBUG | |
5120 | //john's test 0711 | |
5121 | { | |
5122 | int i; | |
5123 | printk("@@ wrq->u pointer = "); | |
5124 | for(i=0;i<wrq->u.data.length;i++){ | |
5125 | if(i%10==0) printk("\n"); | |
5126 | printk( "%8x|", ((u32*)wrq->u.data.pointer)[i] ); | |
5127 | } | |
5128 | printk("\n"); | |
5129 | } | |
5130 | #endif /*JOHN_DEBUG*/ | |
5131 | ret = ieee80211_wpa_supplicant_ioctl(priv->ieee80211, &wrq->u.data); | |
5132 | break; | |
5133 | ||
5134 | default: | |
5135 | ret = -EOPNOTSUPP; | |
5136 | break; | |
5137 | } | |
5138 | ||
5139 | kfree(ipw); | |
5140 | out: | |
5141 | up(&priv->wx_sem); | |
5142 | ||
5143 | return ret; | |
5144 | } | |
5145 | ||
5e1ad18a | 5146 | static u8 HwRateToMRate90(bool bIsHT, u8 rate) |
ecdfa446 GKH |
5147 | { |
5148 | u8 ret_rate = 0x02; | |
5149 | ||
5150 | if(!bIsHT) { | |
5151 | switch(rate) { | |
5152 | case DESC90_RATE1M: ret_rate = MGN_1M; break; | |
5153 | case DESC90_RATE2M: ret_rate = MGN_2M; break; | |
5154 | case DESC90_RATE5_5M: ret_rate = MGN_5_5M; break; | |
5155 | case DESC90_RATE11M: ret_rate = MGN_11M; break; | |
5156 | case DESC90_RATE6M: ret_rate = MGN_6M; break; | |
5157 | case DESC90_RATE9M: ret_rate = MGN_9M; break; | |
5158 | case DESC90_RATE12M: ret_rate = MGN_12M; break; | |
5159 | case DESC90_RATE18M: ret_rate = MGN_18M; break; | |
5160 | case DESC90_RATE24M: ret_rate = MGN_24M; break; | |
5161 | case DESC90_RATE36M: ret_rate = MGN_36M; break; | |
5162 | case DESC90_RATE48M: ret_rate = MGN_48M; break; | |
5163 | case DESC90_RATE54M: ret_rate = MGN_54M; break; | |
5164 | ||
5165 | default: | |
5166 | RT_TRACE(COMP_RECV, "HwRateToMRate90(): Non supported Rate [%x], bIsHT = %d!!!\n", rate, bIsHT); | |
5167 | break; | |
5168 | } | |
5169 | ||
5170 | } else { | |
5171 | switch(rate) { | |
5172 | case DESC90_RATEMCS0: ret_rate = MGN_MCS0; break; | |
5173 | case DESC90_RATEMCS1: ret_rate = MGN_MCS1; break; | |
5174 | case DESC90_RATEMCS2: ret_rate = MGN_MCS2; break; | |
5175 | case DESC90_RATEMCS3: ret_rate = MGN_MCS3; break; | |
5176 | case DESC90_RATEMCS4: ret_rate = MGN_MCS4; break; | |
5177 | case DESC90_RATEMCS5: ret_rate = MGN_MCS5; break; | |
5178 | case DESC90_RATEMCS6: ret_rate = MGN_MCS6; break; | |
5179 | case DESC90_RATEMCS7: ret_rate = MGN_MCS7; break; | |
5180 | case DESC90_RATEMCS8: ret_rate = MGN_MCS8; break; | |
5181 | case DESC90_RATEMCS9: ret_rate = MGN_MCS9; break; | |
5182 | case DESC90_RATEMCS10: ret_rate = MGN_MCS10; break; | |
5183 | case DESC90_RATEMCS11: ret_rate = MGN_MCS11; break; | |
5184 | case DESC90_RATEMCS12: ret_rate = MGN_MCS12; break; | |
5185 | case DESC90_RATEMCS13: ret_rate = MGN_MCS13; break; | |
5186 | case DESC90_RATEMCS14: ret_rate = MGN_MCS14; break; | |
5187 | case DESC90_RATEMCS15: ret_rate = MGN_MCS15; break; | |
5188 | case DESC90_RATEMCS32: ret_rate = (0x80|0x20); break; | |
5189 | ||
5190 | default: | |
5191 | RT_TRACE(COMP_RECV, "HwRateToMRate90(): Non supported Rate [%x], bIsHT = %d!!!\n",rate, bIsHT); | |
5192 | break; | |
5193 | } | |
5194 | } | |
5195 | ||
5196 | return ret_rate; | |
5197 | } | |
5198 | ||
5199 | /** | |
5200 | * Function: UpdateRxPktTimeStamp | |
5201 | * Overview: Recored down the TSF time stamp when receiving a packet | |
5202 | * | |
5203 | * Input: | |
5204 | * PADAPTER Adapter | |
5205 | * PRT_RFD pRfd, | |
5206 | * | |
5207 | * Output: | |
5208 | * PRT_RFD pRfd | |
5209 | * (pRfd->Status.TimeStampHigh is updated) | |
5210 | * (pRfd->Status.TimeStampLow is updated) | |
5211 | * Return: | |
5212 | * None | |
5213 | */ | |
5e1ad18a | 5214 | static void UpdateRxPktTimeStamp8190 (struct net_device *dev, struct ieee80211_rx_stats *stats) |
ecdfa446 GKH |
5215 | { |
5216 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
5217 | ||
5218 | if(stats->bIsAMPDU && !stats->bFirstMPDU) { | |
5219 | stats->mac_time[0] = priv->LastRxDescTSFLow; | |
5220 | stats->mac_time[1] = priv->LastRxDescTSFHigh; | |
5221 | } else { | |
5222 | priv->LastRxDescTSFLow = stats->mac_time[0]; | |
5223 | priv->LastRxDescTSFHigh = stats->mac_time[1]; | |
5224 | } | |
5225 | } | |
5226 | ||
5e1ad18a | 5227 | static long rtl819x_translate_todbm(u8 signal_strength_index)// 0-100 index. |
ecdfa446 GKH |
5228 | { |
5229 | long signal_power; // in dBm. | |
5230 | ||
5231 | // Translate to dBm (x=0.5y-95). | |
5232 | signal_power = (long)((signal_strength_index + 1) >> 1); | |
5233 | signal_power -= 95; | |
5234 | ||
5235 | return signal_power; | |
5236 | } | |
5237 | ||
5238 | // | |
5239 | // Description: | |
5240 | // Update Rx signal related information in the packet reeived | |
5241 | // to RxStats. User application can query RxStats to realize | |
5242 | // current Rx signal status. | |
5243 | // | |
5244 | // Assumption: | |
5245 | // In normal operation, user only care about the information of the BSS | |
5246 | // and we shall invoke this function if the packet received is from the BSS. | |
5247 | // | |
5e1ad18a | 5248 | static void |
ecdfa446 GKH |
5249 | rtl819x_update_rxsignalstatistics8190pci( |
5250 | struct r8192_priv * priv, | |
5251 | struct ieee80211_rx_stats * pprevious_stats | |
5252 | ) | |
5253 | { | |
5254 | int weighting = 0; | |
5255 | ||
5256 | //2 <ToDo> Update Rx Statistics (such as signal strength and signal quality). | |
5257 | ||
5258 | // Initila state | |
5259 | if(priv->stats.recv_signal_power == 0) | |
5260 | priv->stats.recv_signal_power = pprevious_stats->RecvSignalPower; | |
5261 | ||
5262 | // To avoid the past result restricting the statistics sensitivity, weight the current power (5/6) to speed up the | |
5263 | // reaction of smoothed Signal Power. | |
5264 | if(pprevious_stats->RecvSignalPower > priv->stats.recv_signal_power) | |
5265 | weighting = 5; | |
5266 | else if(pprevious_stats->RecvSignalPower < priv->stats.recv_signal_power) | |
5267 | weighting = (-5); | |
5268 | // | |
5269 | // We need more correct power of received packets and the "SignalStrength" of RxStats have been beautified or translated, | |
5270 | // so we record the correct power in Dbm here. By Bruce, 2008-03-07. | |
5271 | // | |
5272 | priv->stats.recv_signal_power = (priv->stats.recv_signal_power * 5 + pprevious_stats->RecvSignalPower + weighting) / 6; | |
5273 | } | |
5274 | ||
5e1ad18a | 5275 | static void |
ecdfa446 GKH |
5276 | rtl8190_process_cck_rxpathsel( |
5277 | struct r8192_priv * priv, | |
5278 | struct ieee80211_rx_stats * pprevious_stats | |
5279 | ) | |
5280 | { | |
5281 | #ifdef RTL8190P //Only 90P 2T4R need to check | |
5282 | char last_cck_adc_pwdb[4]={0,0,0,0}; | |
5283 | u8 i; | |
5284 | //cosa add for Rx path selection | |
5285 | if(priv->rf_type == RF_2T4R && DM_RxPathSelTable.Enable) | |
5286 | { | |
5287 | if(pprevious_stats->bIsCCK && | |
5288 | (pprevious_stats->bPacketToSelf ||pprevious_stats->bPacketBeacon)) | |
5289 | { | |
5290 | /* record the cck adc_pwdb to the sliding window. */ | |
5291 | if(priv->stats.cck_adc_pwdb.TotalNum++ >= PHY_RSSI_SLID_WIN_MAX) | |
5292 | { | |
5293 | priv->stats.cck_adc_pwdb.TotalNum = PHY_RSSI_SLID_WIN_MAX; | |
5294 | for(i=RF90_PATH_A; i<RF90_PATH_MAX; i++) | |
5295 | { | |
5296 | last_cck_adc_pwdb[i] = priv->stats.cck_adc_pwdb.elements[i][priv->stats.cck_adc_pwdb.index]; | |
5297 | priv->stats.cck_adc_pwdb.TotalVal[i] -= last_cck_adc_pwdb[i]; | |
5298 | } | |
5299 | } | |
5300 | for(i=RF90_PATH_A; i<RF90_PATH_MAX; i++) | |
5301 | { | |
5302 | priv->stats.cck_adc_pwdb.TotalVal[i] += pprevious_stats->cck_adc_pwdb[i]; | |
5303 | priv->stats.cck_adc_pwdb.elements[i][priv->stats.cck_adc_pwdb.index] = pprevious_stats->cck_adc_pwdb[i]; | |
5304 | } | |
5305 | priv->stats.cck_adc_pwdb.index++; | |
5306 | if(priv->stats.cck_adc_pwdb.index >= PHY_RSSI_SLID_WIN_MAX) | |
5307 | priv->stats.cck_adc_pwdb.index = 0; | |
5308 | ||
5309 | for(i=RF90_PATH_A; i<RF90_PATH_MAX; i++) | |
5310 | { | |
5311 | DM_RxPathSelTable.cck_pwdb_sta[i] = priv->stats.cck_adc_pwdb.TotalVal[i]/priv->stats.cck_adc_pwdb.TotalNum; | |
5312 | } | |
5313 | ||
5314 | for(i=RF90_PATH_A; i<RF90_PATH_MAX; i++) | |
5315 | { | |
5316 | if(pprevious_stats->cck_adc_pwdb[i] > (char)priv->undecorated_smoothed_cck_adc_pwdb[i]) | |
5317 | { | |
5318 | priv->undecorated_smoothed_cck_adc_pwdb[i] = | |
5319 | ( (priv->undecorated_smoothed_cck_adc_pwdb[i]*(Rx_Smooth_Factor-1)) + | |
5320 | (pprevious_stats->cck_adc_pwdb[i])) /(Rx_Smooth_Factor); | |
5321 | priv->undecorated_smoothed_cck_adc_pwdb[i] = priv->undecorated_smoothed_cck_adc_pwdb[i] + 1; | |
5322 | } | |
5323 | else | |
5324 | { | |
5325 | priv->undecorated_smoothed_cck_adc_pwdb[i] = | |
5326 | ( (priv->undecorated_smoothed_cck_adc_pwdb[i]*(Rx_Smooth_Factor-1)) + | |
5327 | (pprevious_stats->cck_adc_pwdb[i])) /(Rx_Smooth_Factor); | |
5328 | } | |
5329 | } | |
5330 | } | |
5331 | } | |
5332 | #endif | |
5333 | } | |
5334 | ||
5335 | ||
5336 | /* 2008/01/22 MH We can not delcare RSSI/EVM total value of sliding window to | |
5337 | be a local static. Otherwise, it may increase when we return from S3/S4. The | |
5338 | value will be kept in memory or disk. We must delcare the value in adapter | |
5339 | and it will be reinitialized when return from S3/S4. */ | |
5e1ad18a | 5340 | static void rtl8192_process_phyinfo(struct r8192_priv * priv, u8* buffer,struct ieee80211_rx_stats * pprevious_stats, struct ieee80211_rx_stats * pcurrent_stats) |
ecdfa446 GKH |
5341 | { |
5342 | bool bcheck = false; | |
5343 | u8 rfpath; | |
5344 | u32 nspatial_stream, tmp_val; | |
5345 | //u8 i; | |
5346 | static u32 slide_rssi_index=0, slide_rssi_statistics=0; | |
5347 | static u32 slide_evm_index=0, slide_evm_statistics=0; | |
5348 | static u32 last_rssi=0, last_evm=0; | |
5349 | //cosa add for rx path selection | |
5350 | // static long slide_cck_adc_pwdb_index=0, slide_cck_adc_pwdb_statistics=0; | |
5351 | // static char last_cck_adc_pwdb[4]={0,0,0,0}; | |
5352 | //cosa add for beacon rssi smoothing | |
5353 | static u32 slide_beacon_adc_pwdb_index=0, slide_beacon_adc_pwdb_statistics=0; | |
5354 | static u32 last_beacon_adc_pwdb=0; | |
5355 | ||
5356 | struct ieee80211_hdr_3addr *hdr; | |
5357 | u16 sc ; | |
5358 | unsigned int frag,seq; | |
5359 | hdr = (struct ieee80211_hdr_3addr *)buffer; | |
5360 | sc = le16_to_cpu(hdr->seq_ctl); | |
5361 | frag = WLAN_GET_SEQ_FRAG(sc); | |
5362 | seq = WLAN_GET_SEQ_SEQ(sc); | |
5363 | //cosa add 04292008 to record the sequence number | |
5364 | pcurrent_stats->Seq_Num = seq; | |
5365 | // | |
5366 | // Check whether we should take the previous packet into accounting | |
5367 | // | |
5368 | if(!pprevious_stats->bIsAMPDU) | |
5369 | { | |
5370 | // if previous packet is not aggregated packet | |
5371 | bcheck = true; | |
5372 | }else | |
5373 | { | |
5374 | //remve for that we don't use AMPDU to calculate PWDB,because the reported PWDB of some AP is fault. | |
5375 | #if 0 | |
5376 | // if previous packet is aggregated packet, and current packet | |
5377 | // (1) is not AMPDU | |
5378 | // (2) is the first packet of one AMPDU | |
5379 | // that means the previous packet is the last one aggregated packet | |
5380 | if( !pcurrent_stats->bIsAMPDU || pcurrent_stats->bFirstMPDU) | |
5381 | bcheck = true; | |
5382 | #endif | |
5383 | } | |
5384 | ||
5385 | if(slide_rssi_statistics++ >= PHY_RSSI_SLID_WIN_MAX) | |
5386 | { | |
5387 | slide_rssi_statistics = PHY_RSSI_SLID_WIN_MAX; | |
5388 | last_rssi = priv->stats.slide_signal_strength[slide_rssi_index]; | |
5389 | priv->stats.slide_rssi_total -= last_rssi; | |
5390 | } | |
5391 | priv->stats.slide_rssi_total += pprevious_stats->SignalStrength; | |
5392 | ||
5393 | priv->stats.slide_signal_strength[slide_rssi_index++] = pprevious_stats->SignalStrength; | |
5394 | if(slide_rssi_index >= PHY_RSSI_SLID_WIN_MAX) | |
5395 | slide_rssi_index = 0; | |
5396 | ||
5397 | // <1> Showed on UI for user, in dbm | |
5398 | tmp_val = priv->stats.slide_rssi_total/slide_rssi_statistics; | |
5399 | priv->stats.signal_strength = rtl819x_translate_todbm((u8)tmp_val); | |
5400 | pcurrent_stats->rssi = priv->stats.signal_strength; | |
5401 | // | |
5402 | // If the previous packet does not match the criteria, neglect it | |
5403 | // | |
5404 | if(!pprevious_stats->bPacketMatchBSSID) | |
5405 | { | |
5406 | if(!pprevious_stats->bToSelfBA) | |
5407 | return; | |
5408 | } | |
5409 | ||
5410 | if(!bcheck) | |
5411 | return; | |
5412 | ||
5413 | rtl8190_process_cck_rxpathsel(priv,pprevious_stats); | |
5414 | ||
5415 | // | |
5416 | // Check RSSI | |
5417 | // | |
5418 | priv->stats.num_process_phyinfo++; | |
5419 | #if 0 | |
5420 | /* record the general signal strength to the sliding window. */ | |
5421 | if(slide_rssi_statistics++ >= PHY_RSSI_SLID_WIN_MAX) | |
5422 | { | |
5423 | slide_rssi_statistics = PHY_RSSI_SLID_WIN_MAX; | |
5424 | last_rssi = priv->stats.slide_signal_strength[slide_rssi_index]; | |
5425 | priv->stats.slide_rssi_total -= last_rssi; | |
5426 | } | |
5427 | priv->stats.slide_rssi_total += pprevious_stats->SignalStrength; | |
5428 | ||
5429 | priv->stats.slide_signal_strength[slide_rssi_index++] = pprevious_stats->SignalStrength; | |
5430 | if(slide_rssi_index >= PHY_RSSI_SLID_WIN_MAX) | |
5431 | slide_rssi_index = 0; | |
5432 | ||
5433 | // <1> Showed on UI for user, in dbm | |
5434 | tmp_val = priv->stats.slide_rssi_total/slide_rssi_statistics; | |
5435 | priv->stats.signal_strength = rtl819x_translate_todbm((u8)tmp_val); | |
5436 | ||
5437 | #endif | |
5438 | // <2> Showed on UI for engineering | |
5439 | // hardware does not provide rssi information for each rf path in CCK | |
5440 | if(!pprevious_stats->bIsCCK && pprevious_stats->bPacketToSelf) | |
5441 | { | |
5442 | for (rfpath = RF90_PATH_A; rfpath < RF90_PATH_C; rfpath++) | |
5443 | { | |
5444 | if (!rtl8192_phy_CheckIsLegalRFPath(priv->ieee80211->dev, rfpath)) | |
5445 | continue; | |
5446 | RT_TRACE(COMP_DBG,"Jacken -> pPreviousstats->RxMIMOSignalStrength[rfpath] = %d \n" ,pprevious_stats->RxMIMOSignalStrength[rfpath] ); | |
5447 | //Fixed by Jacken 2008-03-20 | |
5448 | if(priv->stats.rx_rssi_percentage[rfpath] == 0) | |
5449 | { | |
5450 | priv->stats.rx_rssi_percentage[rfpath] = pprevious_stats->RxMIMOSignalStrength[rfpath]; | |
5451 | //DbgPrint("MIMO RSSI initialize \n"); | |
5452 | } | |
5453 | if(pprevious_stats->RxMIMOSignalStrength[rfpath] > priv->stats.rx_rssi_percentage[rfpath]) | |
5454 | { | |
5455 | priv->stats.rx_rssi_percentage[rfpath] = | |
5456 | ( (priv->stats.rx_rssi_percentage[rfpath]*(Rx_Smooth_Factor-1)) + | |
5457 | (pprevious_stats->RxMIMOSignalStrength[rfpath])) /(Rx_Smooth_Factor); | |
5458 | priv->stats.rx_rssi_percentage[rfpath] = priv->stats.rx_rssi_percentage[rfpath] + 1; | |
5459 | } | |
5460 | else | |
5461 | { | |
5462 | priv->stats.rx_rssi_percentage[rfpath] = | |
5463 | ( (priv->stats.rx_rssi_percentage[rfpath]*(Rx_Smooth_Factor-1)) + | |
5464 | (pprevious_stats->RxMIMOSignalStrength[rfpath])) /(Rx_Smooth_Factor); | |
5465 | } | |
5466 | RT_TRACE(COMP_DBG,"Jacken -> priv->RxStats.RxRSSIPercentage[rfPath] = %d \n" ,priv->stats.rx_rssi_percentage[rfpath] ); | |
5467 | } | |
5468 | } | |
5469 | ||
5470 | ||
5471 | // | |
5472 | // Check PWDB. | |
5473 | // | |
5474 | //cosa add for beacon rssi smoothing by average. | |
5475 | if(pprevious_stats->bPacketBeacon) | |
5476 | { | |
5477 | /* record the beacon pwdb to the sliding window. */ | |
5478 | if(slide_beacon_adc_pwdb_statistics++ >= PHY_Beacon_RSSI_SLID_WIN_MAX) | |
5479 | { | |
5480 | slide_beacon_adc_pwdb_statistics = PHY_Beacon_RSSI_SLID_WIN_MAX; | |
5481 | last_beacon_adc_pwdb = priv->stats.Slide_Beacon_pwdb[slide_beacon_adc_pwdb_index]; | |
5482 | priv->stats.Slide_Beacon_Total -= last_beacon_adc_pwdb; | |
5483 | //DbgPrint("slide_beacon_adc_pwdb_index = %d, last_beacon_adc_pwdb = %d, Adapter->RxStats.Slide_Beacon_Total = %d\n", | |
5484 | // slide_beacon_adc_pwdb_index, last_beacon_adc_pwdb, Adapter->RxStats.Slide_Beacon_Total); | |
5485 | } | |
5486 | priv->stats.Slide_Beacon_Total += pprevious_stats->RxPWDBAll; | |
5487 | priv->stats.Slide_Beacon_pwdb[slide_beacon_adc_pwdb_index] = pprevious_stats->RxPWDBAll; | |
5488 | //DbgPrint("slide_beacon_adc_pwdb_index = %d, pPreviousRfd->Status.RxPWDBAll = %d\n", slide_beacon_adc_pwdb_index, pPreviousRfd->Status.RxPWDBAll); | |
5489 | slide_beacon_adc_pwdb_index++; | |
5490 | if(slide_beacon_adc_pwdb_index >= PHY_Beacon_RSSI_SLID_WIN_MAX) | |
5491 | slide_beacon_adc_pwdb_index = 0; | |
5492 | pprevious_stats->RxPWDBAll = priv->stats.Slide_Beacon_Total/slide_beacon_adc_pwdb_statistics; | |
5493 | if(pprevious_stats->RxPWDBAll >= 3) | |
5494 | pprevious_stats->RxPWDBAll -= 3; | |
5495 | } | |
5496 | ||
5497 | RT_TRACE(COMP_RXDESC, "Smooth %s PWDB = %d\n", | |
5498 | pprevious_stats->bIsCCK? "CCK": "OFDM", | |
5499 | pprevious_stats->RxPWDBAll); | |
5500 | ||
5501 | if(pprevious_stats->bPacketToSelf || pprevious_stats->bPacketBeacon || pprevious_stats->bToSelfBA) | |
5502 | { | |
5503 | if(priv->undecorated_smoothed_pwdb < 0) // initialize | |
5504 | { | |
5505 | priv->undecorated_smoothed_pwdb = pprevious_stats->RxPWDBAll; | |
5506 | //DbgPrint("First pwdb initialize \n"); | |
5507 | } | |
5508 | #if 1 | |
5509 | if(pprevious_stats->RxPWDBAll > (u32)priv->undecorated_smoothed_pwdb) | |
5510 | { | |
5511 | priv->undecorated_smoothed_pwdb = | |
5512 | ( ((priv->undecorated_smoothed_pwdb)*(Rx_Smooth_Factor-1)) + | |
5513 | (pprevious_stats->RxPWDBAll)) /(Rx_Smooth_Factor); | |
5514 | priv->undecorated_smoothed_pwdb = priv->undecorated_smoothed_pwdb + 1; | |
5515 | } | |
5516 | else | |
5517 | { | |
5518 | priv->undecorated_smoothed_pwdb = | |
5519 | ( ((priv->undecorated_smoothed_pwdb)*(Rx_Smooth_Factor-1)) + | |
5520 | (pprevious_stats->RxPWDBAll)) /(Rx_Smooth_Factor); | |
5521 | } | |
5522 | #else | |
5523 | //Fixed by Jacken 2008-03-20 | |
5524 | if(pPreviousRfd->Status.RxPWDBAll > (u32)pHalData->UndecoratedSmoothedPWDB) | |
5525 | { | |
5526 | pHalData->UndecoratedSmoothedPWDB = | |
5527 | ( ((pHalData->UndecoratedSmoothedPWDB)* 5) + (pPreviousRfd->Status.RxPWDBAll)) / 6; | |
5528 | pHalData->UndecoratedSmoothedPWDB = pHalData->UndecoratedSmoothedPWDB + 1; | |
5529 | } | |
5530 | else | |
5531 | { | |
5532 | pHalData->UndecoratedSmoothedPWDB = | |
5533 | ( ((pHalData->UndecoratedSmoothedPWDB)* 5) + (pPreviousRfd->Status.RxPWDBAll)) / 6; | |
5534 | } | |
5535 | #endif | |
5536 | rtl819x_update_rxsignalstatistics8190pci(priv,pprevious_stats); | |
5537 | } | |
5538 | ||
5539 | // | |
5540 | // Check EVM | |
5541 | // | |
5542 | /* record the general EVM to the sliding window. */ | |
5543 | if(pprevious_stats->SignalQuality == 0) | |
5544 | { | |
5545 | } | |
5546 | else | |
5547 | { | |
5548 | if(pprevious_stats->bPacketToSelf || pprevious_stats->bPacketBeacon || pprevious_stats->bToSelfBA){ | |
5549 | if(slide_evm_statistics++ >= PHY_RSSI_SLID_WIN_MAX){ | |
5550 | slide_evm_statistics = PHY_RSSI_SLID_WIN_MAX; | |
5551 | last_evm = priv->stats.slide_evm[slide_evm_index]; | |
5552 | priv->stats.slide_evm_total -= last_evm; | |
5553 | } | |
5554 | ||
5555 | priv->stats.slide_evm_total += pprevious_stats->SignalQuality; | |
5556 | ||
5557 | priv->stats.slide_evm[slide_evm_index++] = pprevious_stats->SignalQuality; | |
5558 | if(slide_evm_index >= PHY_RSSI_SLID_WIN_MAX) | |
5559 | slide_evm_index = 0; | |
5560 | ||
5561 | // <1> Showed on UI for user, in percentage. | |
5562 | tmp_val = priv->stats.slide_evm_total/slide_evm_statistics; | |
5563 | priv->stats.signal_quality = tmp_val; | |
5564 | //cosa add 10/11/2007, Showed on UI for user in Windows Vista, for Link quality. | |
5565 | priv->stats.last_signal_strength_inpercent = tmp_val; | |
5566 | } | |
5567 | ||
5568 | // <2> Showed on UI for engineering | |
5569 | if(pprevious_stats->bPacketToSelf || pprevious_stats->bPacketBeacon || pprevious_stats->bToSelfBA) | |
5570 | { | |
5571 | for(nspatial_stream = 0; nspatial_stream<2 ; nspatial_stream++) // 2 spatial stream | |
5572 | { | |
5573 | if(pprevious_stats->RxMIMOSignalQuality[nspatial_stream] != -1) | |
5574 | { | |
5575 | if(priv->stats.rx_evm_percentage[nspatial_stream] == 0) // initialize | |
5576 | { | |
5577 | priv->stats.rx_evm_percentage[nspatial_stream] = pprevious_stats->RxMIMOSignalQuality[nspatial_stream]; | |
5578 | } | |
5579 | priv->stats.rx_evm_percentage[nspatial_stream] = | |
5580 | ( (priv->stats.rx_evm_percentage[nspatial_stream]* (Rx_Smooth_Factor-1)) + | |
5581 | (pprevious_stats->RxMIMOSignalQuality[nspatial_stream]* 1)) / (Rx_Smooth_Factor); | |
5582 | } | |
5583 | } | |
5584 | } | |
5585 | } | |
5586 | ||
5587 | } | |
5588 | ||
5589 | /*----------------------------------------------------------------------------- | |
5590 | * Function: rtl819x_query_rxpwrpercentage() | |
5591 | * | |
5592 | * Overview: | |
5593 | * | |
5594 | * Input: char antpower | |
5595 | * | |
5596 | * Output: NONE | |
5597 | * | |
5598 | * Return: 0-100 percentage | |
5599 | * | |
5600 | * Revised History: | |
5601 | * When Who Remark | |
5602 | * 05/26/2008 amy Create Version 0 porting from windows code. | |
5603 | * | |
5604 | *---------------------------------------------------------------------------*/ | |
5605 | static u8 rtl819x_query_rxpwrpercentage( | |
5606 | char antpower | |
5607 | ) | |
5608 | { | |
5609 | if ((antpower <= -100) || (antpower >= 20)) | |
5610 | { | |
5611 | return 0; | |
5612 | } | |
5613 | else if (antpower >= 0) | |
5614 | { | |
5615 | return 100; | |
5616 | } | |
5617 | else | |
5618 | { | |
5619 | return (100+antpower); | |
5620 | } | |
5621 | ||
5622 | } /* QueryRxPwrPercentage */ | |
5623 | ||
5624 | static u8 | |
5625 | rtl819x_evm_dbtopercentage( | |
5626 | char value | |
5627 | ) | |
5628 | { | |
5629 | char ret_val; | |
5630 | ||
5631 | ret_val = value; | |
5632 | ||
5633 | if(ret_val >= 0) | |
5634 | ret_val = 0; | |
5635 | if(ret_val <= -33) | |
5636 | ret_val = -33; | |
5637 | ret_val = 0 - ret_val; | |
5638 | ret_val*=3; | |
5639 | if(ret_val == 99) | |
5640 | ret_val = 100; | |
5641 | return(ret_val); | |
5642 | } | |
5643 | ||
5644 | // | |
5645 | // Description: | |
5646 | // We want good-looking for signal strength/quality | |
5647 | // 2007/7/19 01:09, by cosa. | |
5648 | // | |
5e1ad18a | 5649 | static long rtl819x_signal_scale_mapping(long currsig) |
ecdfa446 GKH |
5650 | { |
5651 | long retsig; | |
5652 | ||
5653 | // Step 1. Scale mapping. | |
5654 | if(currsig >= 61 && currsig <= 100) | |
5655 | { | |
5656 | retsig = 90 + ((currsig - 60) / 4); | |
5657 | } | |
5658 | else if(currsig >= 41 && currsig <= 60) | |
5659 | { | |
5660 | retsig = 78 + ((currsig - 40) / 2); | |
5661 | } | |
5662 | else if(currsig >= 31 && currsig <= 40) | |
5663 | { | |
5664 | retsig = 66 + (currsig - 30); | |
5665 | } | |
5666 | else if(currsig >= 21 && currsig <= 30) | |
5667 | { | |
5668 | retsig = 54 + (currsig - 20); | |
5669 | } | |
5670 | else if(currsig >= 5 && currsig <= 20) | |
5671 | { | |
5672 | retsig = 42 + (((currsig - 5) * 2) / 3); | |
5673 | } | |
5674 | else if(currsig == 4) | |
5675 | { | |
5676 | retsig = 36; | |
5677 | } | |
5678 | else if(currsig == 3) | |
5679 | { | |
5680 | retsig = 27; | |
5681 | } | |
5682 | else if(currsig == 2) | |
5683 | { | |
5684 | retsig = 18; | |
5685 | } | |
5686 | else if(currsig == 1) | |
5687 | { | |
5688 | retsig = 9; | |
5689 | } | |
5690 | else | |
5691 | { | |
5692 | retsig = currsig; | |
5693 | } | |
5694 | ||
5695 | return retsig; | |
5696 | } | |
5697 | ||
5698 | static void rtl8192_query_rxphystatus( | |
5699 | struct r8192_priv * priv, | |
5700 | struct ieee80211_rx_stats * pstats, | |
5701 | prx_desc_819x_pci pdesc, | |
5702 | prx_fwinfo_819x_pci pdrvinfo, | |
5703 | struct ieee80211_rx_stats * precord_stats, | |
5704 | bool bpacket_match_bssid, | |
5705 | bool bpacket_toself, | |
5706 | bool bPacketBeacon, | |
5707 | bool bToSelfBA | |
5708 | ) | |
5709 | { | |
5710 | //PRT_RFD_STATUS pRtRfdStatus = &(pRfd->Status); | |
5711 | phy_sts_ofdm_819xpci_t* pofdm_buf; | |
5712 | phy_sts_cck_819xpci_t * pcck_buf; | |
5713 | phy_ofdm_rx_status_rxsc_sgien_exintfflag* prxsc; | |
5714 | u8 *prxpkt; | |
5715 | u8 i,max_spatial_stream, tmp_rxsnr, tmp_rxevm, rxsc_sgien_exflg; | |
5716 | char rx_pwr[4], rx_pwr_all=0; | |
5717 | //long rx_avg_pwr = 0; | |
5718 | char rx_snrX, rx_evmX; | |
5719 | u8 evm, pwdb_all; | |
5720 | u32 RSSI, total_rssi=0;//, total_evm=0; | |
5721 | // long signal_strength_index = 0; | |
5722 | u8 is_cck_rate=0; | |
5723 | u8 rf_rx_num = 0; | |
5724 | ||
5725 | /* 2007/07/04 MH For OFDM RSSI. For high power or not. */ | |
5726 | static u8 check_reg824 = 0; | |
5727 | static u32 reg824_bit9 = 0; | |
5728 | ||
5729 | priv->stats.numqry_phystatus++; | |
5730 | ||
5731 | is_cck_rate = rx_hal_is_cck_rate(pdrvinfo); | |
5732 | ||
5733 | // Record it for next packet processing | |
5734 | memset(precord_stats, 0, sizeof(struct ieee80211_rx_stats)); | |
5735 | pstats->bPacketMatchBSSID = precord_stats->bPacketMatchBSSID = bpacket_match_bssid; | |
5736 | pstats->bPacketToSelf = precord_stats->bPacketToSelf = bpacket_toself; | |
5737 | pstats->bIsCCK = precord_stats->bIsCCK = is_cck_rate;//RX_HAL_IS_CCK_RATE(pDrvInfo); | |
5738 | pstats->bPacketBeacon = precord_stats->bPacketBeacon = bPacketBeacon; | |
5739 | pstats->bToSelfBA = precord_stats->bToSelfBA = bToSelfBA; | |
5740 | /*2007.08.30 requested by SD3 Jerry */ | |
5741 | if(check_reg824 == 0) | |
5742 | { | |
5743 | reg824_bit9 = rtl8192_QueryBBReg(priv->ieee80211->dev, rFPGA0_XA_HSSIParameter2, 0x200); | |
5744 | check_reg824 = 1; | |
5745 | } | |
5746 | ||
5747 | ||
5748 | prxpkt = (u8*)pdrvinfo; | |
5749 | ||
5750 | /* Move pointer to the 16th bytes. Phy status start address. */ | |
5751 | prxpkt += sizeof(rx_fwinfo_819x_pci); | |
5752 | ||
5753 | /* Initial the cck and ofdm buffer pointer */ | |
5754 | pcck_buf = (phy_sts_cck_819xpci_t *)prxpkt; | |
5755 | pofdm_buf = (phy_sts_ofdm_819xpci_t *)prxpkt; | |
5756 | ||
5757 | pstats->RxMIMOSignalQuality[0] = -1; | |
5758 | pstats->RxMIMOSignalQuality[1] = -1; | |
5759 | precord_stats->RxMIMOSignalQuality[0] = -1; | |
5760 | precord_stats->RxMIMOSignalQuality[1] = -1; | |
5761 | ||
5762 | if(is_cck_rate) | |
5763 | { | |
5764 | // | |
5765 | // (1)Hardware does not provide RSSI for CCK | |
5766 | // | |
5767 | ||
5768 | // | |
5769 | // (2)PWDB, Average PWDB cacluated by hardware (for rate adaptive) | |
5770 | // | |
5771 | u8 report;//, cck_agc_rpt; | |
5772 | #ifdef RTL8190P | |
5773 | u8 tmp_pwdb; | |
5774 | char cck_adc_pwdb[4]; | |
5775 | #endif | |
5776 | priv->stats.numqry_phystatusCCK++; | |
5777 | ||
5778 | #ifdef RTL8190P //Only 90P 2T4R need to check | |
5779 | if(priv->rf_type == RF_2T4R && DM_RxPathSelTable.Enable && bpacket_match_bssid) | |
5780 | { | |
5781 | for(i=RF90_PATH_A; i<RF90_PATH_MAX; i++) | |
5782 | { | |
5783 | tmp_pwdb = pcck_buf->adc_pwdb_X[i]; | |
5784 | cck_adc_pwdb[i] = (char)tmp_pwdb; | |
5785 | cck_adc_pwdb[i] /= 2; | |
5786 | pstats->cck_adc_pwdb[i] = precord_stats->cck_adc_pwdb[i] = cck_adc_pwdb[i]; | |
5787 | //DbgPrint("RF-%d tmp_pwdb = 0x%x, cck_adc_pwdb = %d", i, tmp_pwdb, cck_adc_pwdb[i]); | |
5788 | } | |
5789 | } | |
5790 | #endif | |
5791 | ||
5792 | if(!reg824_bit9) | |
5793 | { | |
5794 | report = pcck_buf->cck_agc_rpt & 0xc0; | |
5795 | report = report>>6; | |
5796 | switch(report) | |
5797 | { | |
5798 | //Fixed by Jacken from Bryant 2008-03-20 | |
5799 | //Original value is -38 , -26 , -14 , -2 | |
5800 | //Fixed value is -35 , -23 , -11 , 6 | |
5801 | case 0x3: | |
5802 | rx_pwr_all = -35 - (pcck_buf->cck_agc_rpt & 0x3e); | |
5803 | break; | |
5804 | case 0x2: | |
5805 | rx_pwr_all = -23 - (pcck_buf->cck_agc_rpt & 0x3e); | |
5806 | break; | |
5807 | case 0x1: | |
5808 | rx_pwr_all = -11 - (pcck_buf->cck_agc_rpt & 0x3e); | |
5809 | break; | |
5810 | case 0x0: | |
5811 | rx_pwr_all = 8 - (pcck_buf->cck_agc_rpt & 0x3e); | |
5812 | break; | |
5813 | } | |
5814 | } | |
5815 | else | |
5816 | { | |
5817 | report = pcck_buf->cck_agc_rpt & 0x60; | |
5818 | report = report>>5; | |
5819 | switch(report) | |
5820 | { | |
5821 | case 0x3: | |
5822 | rx_pwr_all = -35 - ((pcck_buf->cck_agc_rpt & 0x1f)<<1) ; | |
5823 | break; | |
5824 | case 0x2: | |
5825 | rx_pwr_all = -23 - ((pcck_buf->cck_agc_rpt & 0x1f)<<1); | |
5826 | break; | |
5827 | case 0x1: | |
5828 | rx_pwr_all = -11 - ((pcck_buf->cck_agc_rpt & 0x1f)<<1) ; | |
5829 | break; | |
5830 | case 0x0: | |
5831 | rx_pwr_all = -8 - ((pcck_buf->cck_agc_rpt & 0x1f)<<1) ; | |
5832 | break; | |
5833 | } | |
5834 | } | |
5835 | ||
5836 | pwdb_all = rtl819x_query_rxpwrpercentage(rx_pwr_all); | |
5837 | pstats->RxPWDBAll = precord_stats->RxPWDBAll = pwdb_all; | |
5838 | pstats->RecvSignalPower = rx_pwr_all; | |
5839 | ||
5840 | // | |
5841 | // (3) Get Signal Quality (EVM) | |
5842 | // | |
5843 | if(bpacket_match_bssid) | |
5844 | { | |
5845 | u8 sq; | |
5846 | ||
5847 | if(pstats->RxPWDBAll > 40) | |
5848 | { | |
5849 | sq = 100; | |
5850 | }else | |
5851 | { | |
5852 | sq = pcck_buf->sq_rpt; | |
5853 | ||
5854 | if(pcck_buf->sq_rpt > 64) | |
5855 | sq = 0; | |
5856 | else if (pcck_buf->sq_rpt < 20) | |
5857 | sq = 100; | |
5858 | else | |
5859 | sq = ((64-sq) * 100) / 44; | |
5860 | } | |
5861 | pstats->SignalQuality = precord_stats->SignalQuality = sq; | |
5862 | pstats->RxMIMOSignalQuality[0] = precord_stats->RxMIMOSignalQuality[0] = sq; | |
5863 | pstats->RxMIMOSignalQuality[1] = precord_stats->RxMIMOSignalQuality[1] = -1; | |
5864 | } | |
5865 | } | |
5866 | else | |
5867 | { | |
5868 | priv->stats.numqry_phystatusHT++; | |
5869 | // | |
5870 | // (1)Get RSSI for HT rate | |
5871 | // | |
5872 | for(i=RF90_PATH_A; i<RF90_PATH_MAX; i++) | |
5873 | { | |
5874 | // 2008/01/30 MH we will judge RF RX path now. | |
5875 | if (priv->brfpath_rxenable[i]) | |
5876 | rf_rx_num++; | |
5877 | //else | |
5878 | //continue; | |
5879 | ||
5880 | //Fixed by Jacken from Bryant 2008-03-20 | |
5881 | //Original value is 106 | |
5882 | #ifdef RTL8190P //Modify by Jacken 2008/03/31 | |
5883 | rx_pwr[i] = ((pofdm_buf->trsw_gain_X[i]&0x3F)*2) - 106; | |
5884 | #else | |
5885 | rx_pwr[i] = ((pofdm_buf->trsw_gain_X[i]&0x3F)*2) - 110; | |
5886 | #endif | |
5887 | ||
5888 | //Get Rx snr value in DB | |
5889 | tmp_rxsnr = pofdm_buf->rxsnr_X[i]; | |
5890 | rx_snrX = (char)(tmp_rxsnr); | |
5891 | rx_snrX /= 2; | |
5892 | priv->stats.rxSNRdB[i] = (long)rx_snrX; | |
5893 | ||
5894 | /* Translate DBM to percentage. */ | |
5895 | RSSI = rtl819x_query_rxpwrpercentage(rx_pwr[i]); | |
5896 | if (priv->brfpath_rxenable[i]) | |
5897 | total_rssi += RSSI; | |
5898 | ||
5899 | /* Record Signal Strength for next packet */ | |
5900 | if(bpacket_match_bssid) | |
5901 | { | |
5902 | pstats->RxMIMOSignalStrength[i] =(u8) RSSI; | |
5903 | precord_stats->RxMIMOSignalStrength[i] =(u8) RSSI; | |
5904 | } | |
5905 | } | |
5906 | ||
5907 | ||
5908 | // | |
5909 | // (2)PWDB, Average PWDB cacluated by hardware (for rate adaptive) | |
5910 | // | |
5911 | //Fixed by Jacken from Bryant 2008-03-20 | |
5912 | //Original value is 106 | |
5913 | rx_pwr_all = (((pofdm_buf->pwdb_all ) >> 1 )& 0x7f) -106; | |
5914 | pwdb_all = rtl819x_query_rxpwrpercentage(rx_pwr_all); | |
5915 | ||
5916 | pstats->RxPWDBAll = precord_stats->RxPWDBAll = pwdb_all; | |
5917 | pstats->RxPower = precord_stats->RxPower = rx_pwr_all; | |
5918 | pstats->RecvSignalPower = rx_pwr_all; | |
5919 | // | |
5920 | // (3)EVM of HT rate | |
5921 | // | |
5922 | if(pdrvinfo->RxHT && pdrvinfo->RxRate>=DESC90_RATEMCS8 && | |
5923 | pdrvinfo->RxRate<=DESC90_RATEMCS15) | |
5924 | max_spatial_stream = 2; //both spatial stream make sense | |
5925 | else | |
5926 | max_spatial_stream = 1; //only spatial stream 1 makes sense | |
5927 | ||
5928 | for(i=0; i<max_spatial_stream; i++) | |
5929 | { | |
5930 | tmp_rxevm = pofdm_buf->rxevm_X[i]; | |
5931 | rx_evmX = (char)(tmp_rxevm); | |
5932 | ||
5933 | // Do not use shift operation like "rx_evmX >>= 1" because the compilor of free build environment | |
5934 | // fill most significant bit to "zero" when doing shifting operation which may change a negative | |
5935 | // value to positive one, then the dbm value (which is supposed to be negative) is not correct anymore. | |
5936 | rx_evmX /= 2; //dbm | |
5937 | ||
5938 | evm = rtl819x_evm_dbtopercentage(rx_evmX); | |
5939 | #if 0 | |
5940 | EVM = SignalScaleMapping(EVM);//make it good looking, from 0~100 | |
5941 | #endif | |
5942 | if(bpacket_match_bssid) | |
5943 | { | |
5944 | if(i==0) // Fill value in RFD, Get the first spatial stream only | |
5945 | pstats->SignalQuality = precord_stats->SignalQuality = (u8)(evm & 0xff); | |
5946 | pstats->RxMIMOSignalQuality[i] = precord_stats->RxMIMOSignalQuality[i] = (u8)(evm & 0xff); | |
5947 | } | |
5948 | } | |
5949 | ||
5950 | ||
5951 | /* record rx statistics for debug */ | |
5952 | rxsc_sgien_exflg = pofdm_buf->rxsc_sgien_exflg; | |
5953 | prxsc = (phy_ofdm_rx_status_rxsc_sgien_exintfflag *)&rxsc_sgien_exflg; | |
5954 | if(pdrvinfo->BW) //40M channel | |
5955 | priv->stats.received_bwtype[1+prxsc->rxsc]++; | |
5956 | else //20M channel | |
5957 | priv->stats.received_bwtype[0]++; | |
5958 | } | |
5959 | ||
5960 | //UI BSS List signal strength(in percentage), make it good looking, from 0~100. | |
5961 | //It is assigned to the BSS List in GetValueFromBeaconOrProbeRsp(). | |
5962 | if(is_cck_rate) | |
5963 | { | |
5964 | pstats->SignalStrength = precord_stats->SignalStrength = (u8)(rtl819x_signal_scale_mapping((long)pwdb_all));//PWDB_ALL; | |
5965 | ||
5966 | } | |
5967 | else | |
5968 | { | |
5969 | //pRfd->Status.SignalStrength = pRecordRfd->Status.SignalStrength = (u1Byte)(SignalScaleMapping(total_rssi/=RF90_PATH_MAX));//(u1Byte)(total_rssi/=RF90_PATH_MAX); | |
5970 | // We can judge RX path number now. | |
5971 | if (rf_rx_num != 0) | |
5972 | pstats->SignalStrength = precord_stats->SignalStrength = (u8)(rtl819x_signal_scale_mapping((long)(total_rssi/=rf_rx_num))); | |
5973 | } | |
5974 | } /* QueryRxPhyStatus8190Pci */ | |
5975 | ||
5e1ad18a | 5976 | static void |
ecdfa446 GKH |
5977 | rtl8192_record_rxdesc_forlateruse( |
5978 | struct ieee80211_rx_stats * psrc_stats, | |
5979 | struct ieee80211_rx_stats * ptarget_stats | |
5980 | ) | |
5981 | { | |
5982 | ptarget_stats->bIsAMPDU = psrc_stats->bIsAMPDU; | |
5983 | ptarget_stats->bFirstMPDU = psrc_stats->bFirstMPDU; | |
5984 | //ptarget_stats->Seq_Num = psrc_stats->Seq_Num; | |
5985 | } | |
5986 | ||
5987 | ||
5988 | ||
5e1ad18a | 5989 | static void TranslateRxSignalStuff819xpci(struct net_device *dev, |
ecdfa446 GKH |
5990 | struct sk_buff *skb, |
5991 | struct ieee80211_rx_stats * pstats, | |
5992 | prx_desc_819x_pci pdesc, | |
5993 | prx_fwinfo_819x_pci pdrvinfo) | |
5994 | { | |
5995 | // TODO: We must only check packet for current MAC address. Not finish | |
5996 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
5997 | bool bpacket_match_bssid, bpacket_toself; | |
5998 | bool bPacketBeacon=false, bToSelfBA=false; | |
5999 | static struct ieee80211_rx_stats previous_stats; | |
6000 | struct ieee80211_hdr_3addr *hdr; | |
6001 | u16 fc,type; | |
6002 | ||
6003 | // Get Signal Quality for only RX data queue (but not command queue) | |
6004 | ||
6005 | u8* tmp_buf; | |
6006 | u8 *praddr; | |
6007 | ||
6008 | /* Get MAC frame start address. */ | |
6009 | tmp_buf = skb->data; | |
6010 | ||
6011 | hdr = (struct ieee80211_hdr_3addr *)tmp_buf; | |
6012 | fc = le16_to_cpu(hdr->frame_ctl); | |
6013 | type = WLAN_FC_GET_TYPE(fc); | |
6014 | praddr = hdr->addr1; | |
6015 | ||
6016 | /* Check if the received packet is acceptabe. */ | |
6017 | bpacket_match_bssid = ((IEEE80211_FTYPE_CTL != type) && | |
6018 | (eqMacAddr(priv->ieee80211->current_network.bssid, (fc & IEEE80211_FCTL_TODS)? hdr->addr1 : (fc & IEEE80211_FCTL_FROMDS )? hdr->addr2 : hdr->addr3)) | |
6019 | && (!pstats->bHwError) && (!pstats->bCRC)&& (!pstats->bICV)); | |
6020 | bpacket_toself = bpacket_match_bssid & (eqMacAddr(praddr, priv->ieee80211->dev->dev_addr)); | |
6021 | #if 1//cosa | |
6022 | if(WLAN_FC_GET_FRAMETYPE(fc)== IEEE80211_STYPE_BEACON) | |
6023 | { | |
6024 | bPacketBeacon = true; | |
6025 | //DbgPrint("Beacon 2, MatchBSSID = %d, ToSelf = %d \n", bPacketMatchBSSID, bPacketToSelf); | |
6026 | } | |
6027 | if(WLAN_FC_GET_FRAMETYPE(fc) == IEEE80211_STYPE_BLOCKACK) | |
6028 | { | |
6029 | if((eqMacAddr(praddr,dev->dev_addr))) | |
6030 | bToSelfBA = true; | |
6031 | //DbgPrint("BlockAck, MatchBSSID = %d, ToSelf = %d \n", bPacketMatchBSSID, bPacketToSelf); | |
6032 | } | |
6033 | ||
6034 | #endif | |
6035 | if(bpacket_match_bssid) | |
6036 | { | |
6037 | priv->stats.numpacket_matchbssid++; | |
6038 | } | |
6039 | if(bpacket_toself){ | |
6040 | priv->stats.numpacket_toself++; | |
6041 | } | |
6042 | // | |
6043 | // Process PHY information for previous packet (RSSI/PWDB/EVM) | |
6044 | // | |
6045 | // Because phy information is contained in the last packet of AMPDU only, so driver | |
6046 | // should process phy information of previous packet | |
6047 | rtl8192_process_phyinfo(priv, tmp_buf,&previous_stats, pstats); | |
6048 | rtl8192_query_rxphystatus(priv, pstats, pdesc, pdrvinfo, &previous_stats, bpacket_match_bssid, | |
6049 | bpacket_toself ,bPacketBeacon, bToSelfBA); | |
6050 | rtl8192_record_rxdesc_forlateruse(pstats, &previous_stats); | |
6051 | ||
6052 | } | |
6053 | ||
6054 | ||
5e1ad18a | 6055 | static void rtl8192_tx_resume(struct net_device *dev) |
ecdfa446 GKH |
6056 | { |
6057 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
6058 | struct ieee80211_device *ieee = priv->ieee80211; | |
6059 | struct sk_buff *skb; | |
6060 | int queue_index; | |
6061 | ||
6062 | for(queue_index = BK_QUEUE; queue_index < TXCMD_QUEUE;queue_index++) { | |
6063 | while((!skb_queue_empty(&ieee->skb_waitQ[queue_index]))&& | |
6064 | (priv->ieee80211->check_nic_enough_desc(dev,queue_index) > 0)) { | |
6065 | /* 1. dequeue the packet from the wait queue */ | |
6066 | skb = skb_dequeue(&ieee->skb_waitQ[queue_index]); | |
6067 | /* 2. tx the packet directly */ | |
6068 | ieee->softmac_data_hard_start_xmit(skb,dev,0/* rate useless now*/); | |
6069 | #if 0 | |
6070 | if(queue_index!=MGNT_QUEUE) { | |
6071 | ieee->stats.tx_packets++; | |
6072 | ieee->stats.tx_bytes += skb->len; | |
6073 | } | |
6074 | #endif | |
6075 | } | |
6076 | } | |
6077 | } | |
6078 | ||
6079 | void rtl8192_irq_tx_tasklet(struct r8192_priv *priv) | |
6080 | { | |
6081 | rtl8192_tx_resume(priv->ieee80211->dev); | |
6082 | } | |
6083 | ||
6084 | /** | |
6085 | * Function: UpdateReceivedRateHistogramStatistics | |
6086 | * Overview: Recored down the received data rate | |
6087 | * | |
6088 | * Input: | |
6089 | * PADAPTER Adapter | |
6090 | * PRT_RFD pRfd, | |
6091 | * | |
6092 | * Output: | |
6093 | * PRT_TCB Adapter | |
6094 | * (Adapter->RxStats.ReceivedRateHistogram[] is updated) | |
6095 | * Return: | |
6096 | * None | |
6097 | */ | |
5e1ad18a | 6098 | static void UpdateReceivedRateHistogramStatistics8190( |
ecdfa446 GKH |
6099 | struct net_device *dev, |
6100 | struct ieee80211_rx_stats* pstats | |
6101 | ) | |
6102 | { | |
6103 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
6104 | u32 rcvType=1; //0: Total, 1:OK, 2:CRC, 3:ICV | |
6105 | u32 rateIndex; | |
6106 | u32 preamble_guardinterval; //1: short preamble/GI, 0: long preamble/GI | |
6107 | ||
6108 | /* 2007/03/09 MH We will not update rate of packet from rx cmd queue. */ | |
6109 | #if 0 | |
6110 | if (pRfd->queue_id == CMPK_RX_QUEUE_ID) | |
6111 | return; | |
6112 | #endif | |
6113 | if(pstats->bCRC) | |
6114 | rcvType = 2; | |
6115 | else if(pstats->bICV) | |
6116 | rcvType = 3; | |
6117 | ||
6118 | if(pstats->bShortPreamble) | |
6119 | preamble_guardinterval = 1;// short | |
6120 | else | |
6121 | preamble_guardinterval = 0;// long | |
6122 | ||
6123 | switch(pstats->rate) | |
6124 | { | |
6125 | // | |
6126 | // CCK rate | |
6127 | // | |
6128 | case MGN_1M: rateIndex = 0; break; | |
6129 | case MGN_2M: rateIndex = 1; break; | |
6130 | case MGN_5_5M: rateIndex = 2; break; | |
6131 | case MGN_11M: rateIndex = 3; break; | |
6132 | // | |
6133 | // Legacy OFDM rate | |
6134 | // | |
6135 | case MGN_6M: rateIndex = 4; break; | |
6136 | case MGN_9M: rateIndex = 5; break; | |
6137 | case MGN_12M: rateIndex = 6; break; | |
6138 | case MGN_18M: rateIndex = 7; break; | |
6139 | case MGN_24M: rateIndex = 8; break; | |
6140 | case MGN_36M: rateIndex = 9; break; | |
6141 | case MGN_48M: rateIndex = 10; break; | |
6142 | case MGN_54M: rateIndex = 11; break; | |
6143 | // | |
6144 | // 11n High throughput rate | |
6145 | // | |
6146 | case MGN_MCS0: rateIndex = 12; break; | |
6147 | case MGN_MCS1: rateIndex = 13; break; | |
6148 | case MGN_MCS2: rateIndex = 14; break; | |
6149 | case MGN_MCS3: rateIndex = 15; break; | |
6150 | case MGN_MCS4: rateIndex = 16; break; | |
6151 | case MGN_MCS5: rateIndex = 17; break; | |
6152 | case MGN_MCS6: rateIndex = 18; break; | |
6153 | case MGN_MCS7: rateIndex = 19; break; | |
6154 | case MGN_MCS8: rateIndex = 20; break; | |
6155 | case MGN_MCS9: rateIndex = 21; break; | |
6156 | case MGN_MCS10: rateIndex = 22; break; | |
6157 | case MGN_MCS11: rateIndex = 23; break; | |
6158 | case MGN_MCS12: rateIndex = 24; break; | |
6159 | case MGN_MCS13: rateIndex = 25; break; | |
6160 | case MGN_MCS14: rateIndex = 26; break; | |
6161 | case MGN_MCS15: rateIndex = 27; break; | |
6162 | default: rateIndex = 28; break; | |
6163 | } | |
6164 | priv->stats.received_preamble_GI[preamble_guardinterval][rateIndex]++; | |
6165 | priv->stats.received_rate_histogram[0][rateIndex]++; //total | |
6166 | priv->stats.received_rate_histogram[rcvType][rateIndex]++; | |
6167 | } | |
6168 | ||
5e1ad18a | 6169 | static void rtl8192_rx(struct net_device *dev) |
ecdfa446 GKH |
6170 | { |
6171 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
6172 | struct ieee80211_hdr_1addr *ieee80211_hdr = NULL; | |
6173 | bool unicast_packet = false; | |
6174 | struct ieee80211_rx_stats stats = { | |
6175 | .signal = 0, | |
6176 | .noise = -98, | |
6177 | .rate = 0, | |
6178 | .freq = IEEE80211_24GHZ_BAND, | |
6179 | }; | |
6180 | unsigned int count = priv->rxringcount; | |
6181 | ||
6182 | stats.nic_type = NIC_8192E; | |
6183 | ||
6184 | while (count--) { | |
6185 | rx_desc_819x_pci *pdesc = &priv->rx_ring[priv->rx_idx];//rx descriptor | |
6186 | struct sk_buff *skb = priv->rx_buf[priv->rx_idx];//rx pkt | |
6187 | ||
6188 | if (pdesc->OWN){ | |
6189 | /* wait data to be filled by hardware */ | |
6190 | return; | |
6191 | } else { | |
6192 | stats.bICV = pdesc->ICV; | |
6193 | stats.bCRC = pdesc->CRC32; | |
6194 | stats.bHwError = pdesc->CRC32 | pdesc->ICV; | |
6195 | ||
6196 | stats.Length = pdesc->Length; | |
6197 | if(stats.Length < 24) | |
6198 | stats.bHwError |= 1; | |
6199 | ||
6200 | if(stats.bHwError) { | |
6201 | stats.bShift = false; | |
6202 | ||
6203 | if(pdesc->CRC32) { | |
6204 | if (pdesc->Length <500) | |
6205 | priv->stats.rxcrcerrmin++; | |
6206 | else if (pdesc->Length >1000) | |
6207 | priv->stats.rxcrcerrmax++; | |
6208 | else | |
6209 | priv->stats.rxcrcerrmid++; | |
6210 | } | |
6211 | goto done; | |
6212 | } else { | |
6213 | prx_fwinfo_819x_pci pDrvInfo = NULL; | |
6214 | struct sk_buff *new_skb = dev_alloc_skb(priv->rxbuffersize); | |
6215 | ||
6216 | if (unlikely(!new_skb)) { | |
6217 | goto done; | |
6218 | } | |
6219 | ||
6220 | stats.RxDrvInfoSize = pdesc->RxDrvInfoSize; | |
6221 | stats.RxBufShift = ((pdesc->Shift)&0x03); | |
6222 | stats.Decrypted = !pdesc->SWDec; | |
6223 | ||
ecdfa446 | 6224 | pci_dma_sync_single_for_cpu(priv->pdev, |
ecdfa446 GKH |
6225 | *((dma_addr_t *)skb->cb), |
6226 | priv->rxbuffersize, | |
6227 | PCI_DMA_FROMDEVICE); | |
6228 | skb_put(skb, pdesc->Length); | |
6229 | pDrvInfo = (rx_fwinfo_819x_pci *)(skb->data + stats.RxBufShift); | |
6230 | skb_reserve(skb, stats.RxDrvInfoSize + stats.RxBufShift); | |
6231 | ||
6232 | stats.rate = HwRateToMRate90((bool)pDrvInfo->RxHT, (u8)pDrvInfo->RxRate); | |
6233 | stats.bShortPreamble = pDrvInfo->SPLCP; | |
6234 | ||
6235 | /* it is debug only. It should be disabled in released driver. | |
6236 | * 2007.1.11 by Emily | |
6237 | * */ | |
6238 | UpdateReceivedRateHistogramStatistics8190(dev, &stats); | |
6239 | ||
6240 | stats.bIsAMPDU = (pDrvInfo->PartAggr==1); | |
6241 | stats.bFirstMPDU = (pDrvInfo->PartAggr==1) && (pDrvInfo->FirstAGGR==1); | |
6242 | ||
6243 | stats.TimeStampLow = pDrvInfo->TSFL; | |
6244 | stats.TimeStampHigh = read_nic_dword(dev, TSFR+4); | |
6245 | ||
6246 | UpdateRxPktTimeStamp8190(dev, &stats); | |
6247 | ||
6248 | // | |
6249 | // Get Total offset of MPDU Frame Body | |
6250 | // | |
6251 | if((stats.RxBufShift + stats.RxDrvInfoSize) > 0) | |
6252 | stats.bShift = 1; | |
6253 | ||
6254 | stats.RxIs40MHzPacket = pDrvInfo->BW; | |
6255 | ||
6256 | /* ???? */ | |
6257 | TranslateRxSignalStuff819xpci(dev,skb, &stats, pdesc, pDrvInfo); | |
6258 | ||
6259 | /* Rx A-MPDU */ | |
6260 | if(pDrvInfo->FirstAGGR==1 || pDrvInfo->PartAggr == 1) | |
6261 | RT_TRACE(COMP_RXDESC, "pDrvInfo->FirstAGGR = %d, pDrvInfo->PartAggr = %d\n", | |
6262 | pDrvInfo->FirstAGGR, pDrvInfo->PartAggr); | |
6263 | skb_trim(skb, skb->len - 4/*sCrcLng*/); | |
6264 | /* rx packets statistics */ | |
6265 | ieee80211_hdr = (struct ieee80211_hdr_1addr *)skb->data; | |
6266 | unicast_packet = false; | |
6267 | ||
6268 | if(is_broadcast_ether_addr(ieee80211_hdr->addr1)) { | |
6269 | //TODO | |
6270 | }else if(is_multicast_ether_addr(ieee80211_hdr->addr1)){ | |
6271 | //TODO | |
6272 | }else { | |
6273 | /* unicast packet */ | |
6274 | unicast_packet = true; | |
6275 | } | |
6276 | ||
6277 | stats.packetlength = stats.Length-4; | |
6278 | stats.fraglength = stats.packetlength; | |
6279 | stats.fragoffset = 0; | |
6280 | stats.ntotalfrag = 1; | |
6281 | ||
fb5fe277 | 6282 | if(!ieee80211_rtl_rx(priv->ieee80211, skb, &stats)){ |
ecdfa446 GKH |
6283 | dev_kfree_skb_any(skb); |
6284 | } else { | |
6285 | priv->stats.rxok++; | |
6286 | if(unicast_packet) { | |
6287 | priv->stats.rxbytesunicast += skb->len; | |
6288 | } | |
6289 | } | |
6290 | ||
6291 | skb = new_skb; | |
6292 | priv->rx_buf[priv->rx_idx] = skb; | |
6293 | *((dma_addr_t *) skb->cb) = pci_map_single(priv->pdev, skb->tail, priv->rxbuffersize, PCI_DMA_FROMDEVICE); | |
6294 | // *((dma_addr_t *) skb->cb) = pci_map_single(priv->pdev, skb_tail_pointer(skb), priv->rxbuffersize, PCI_DMA_FROMDEVICE); | |
6295 | } | |
6296 | ||
6297 | } | |
6298 | done: | |
6299 | pdesc->BufferAddress = cpu_to_le32(*((dma_addr_t *)skb->cb)); | |
6300 | pdesc->OWN = 1; | |
6301 | pdesc->Length = priv->rxbuffersize; | |
6302 | if (priv->rx_idx == priv->rxringcount-1) | |
6303 | pdesc->EOR = 1; | |
6304 | priv->rx_idx = (priv->rx_idx + 1) % priv->rxringcount; | |
6305 | } | |
6306 | ||
6307 | } | |
6308 | ||
6309 | void rtl8192_irq_rx_tasklet(struct r8192_priv *priv) | |
6310 | { | |
6311 | rtl8192_rx(priv->ieee80211->dev); | |
6312 | /* unmask RDU */ | |
6313 | write_nic_dword(priv->ieee80211->dev, INTA_MASK,read_nic_dword(priv->ieee80211->dev, INTA_MASK) | IMR_RDU); | |
6314 | } | |
6315 | ||
6316 | static const struct net_device_ops rtl8192_netdev_ops = { | |
6317 | .ndo_open = rtl8192_open, | |
6318 | .ndo_stop = rtl8192_close, | |
6319 | /* .ndo_get_stats = rtl8192_stats, */ | |
6320 | .ndo_tx_timeout = tx_timeout, | |
6321 | .ndo_do_ioctl = rtl8192_ioctl, | |
6322 | .ndo_set_multicast_list = r8192_set_multicast, | |
6323 | .ndo_set_mac_address = r8192_set_mac_adr, | |
fb5fe277 | 6324 | .ndo_start_xmit = ieee80211_rtl_xmit, |
ecdfa446 GKH |
6325 | }; |
6326 | ||
6327 | /**************************************************************************** | |
6328 | ---------------------------- PCI_STUFF--------------------------- | |
6329 | *****************************************************************************/ | |
6330 | ||
6331 | static int __devinit rtl8192_pci_probe(struct pci_dev *pdev, | |
6332 | const struct pci_device_id *id) | |
6333 | { | |
6334 | unsigned long ioaddr = 0; | |
6335 | struct net_device *dev = NULL; | |
6336 | struct r8192_priv *priv= NULL; | |
6337 | u8 unit = 0; | |
6338 | ||
6339 | #ifdef CONFIG_RTL8192_IO_MAP | |
6340 | unsigned long pio_start, pio_len, pio_flags; | |
6341 | #else | |
6342 | unsigned long pmem_start, pmem_len, pmem_flags; | |
6343 | #endif //end #ifdef RTL_IO_MAP | |
6344 | ||
6345 | RT_TRACE(COMP_INIT,"Configuring chip resources"); | |
6346 | ||
6347 | if( pci_enable_device (pdev) ){ | |
6348 | RT_TRACE(COMP_ERR,"Failed to enable PCI device"); | |
6349 | return -EIO; | |
6350 | } | |
6351 | ||
6352 | pci_set_master(pdev); | |
6353 | //pci_set_wmi(pdev); | |
6354 | pci_set_dma_mask(pdev, 0xffffff00ULL); | |
ecdfa446 | 6355 | pci_set_consistent_dma_mask(pdev,0xffffff00ULL); |
ecdfa446 GKH |
6356 | dev = alloc_ieee80211(sizeof(struct r8192_priv)); |
6357 | if (!dev) | |
6358 | return -ENOMEM; | |
6359 | ||
ecdfa446 | 6360 | pci_set_drvdata(pdev, dev); |
ecdfa446 | 6361 | SET_NETDEV_DEV(dev, &pdev->dev); |
ecdfa446 | 6362 | priv = ieee80211_priv(dev); |
ecdfa446 | 6363 | priv->ieee80211 = netdev_priv(dev); |
ecdfa446 | 6364 | priv->pdev=pdev; |
ecdfa446 GKH |
6365 | if((pdev->subsystem_vendor == PCI_VENDOR_ID_DLINK)&&(pdev->subsystem_device == 0x3304)){ |
6366 | priv->ieee80211->bSupportRemoteWakeUp = 1; | |
6367 | } else | |
ecdfa446 GKH |
6368 | { |
6369 | priv->ieee80211->bSupportRemoteWakeUp = 0; | |
6370 | } | |
6371 | ||
6372 | #ifdef CONFIG_RTL8192_IO_MAP | |
6373 | ||
6374 | pio_start = (unsigned long)pci_resource_start (pdev, 0); | |
6375 | pio_len = (unsigned long)pci_resource_len (pdev, 0); | |
6376 | pio_flags = (unsigned long)pci_resource_flags (pdev, 0); | |
6377 | ||
6378 | if (!(pio_flags & IORESOURCE_IO)) { | |
6379 | RT_TRACE(COMP_ERR,"region #0 not a PIO resource, aborting"); | |
6380 | goto fail; | |
6381 | } | |
6382 | ||
6383 | //DMESG("IO space @ 0x%08lx", pio_start ); | |
6384 | if( ! request_region( pio_start, pio_len, RTL819xE_MODULE_NAME ) ){ | |
6385 | RT_TRACE(COMP_ERR,"request_region failed!"); | |
6386 | goto fail; | |
6387 | } | |
6388 | ||
6389 | ioaddr = pio_start; | |
6390 | dev->base_addr = ioaddr; // device I/O address | |
6391 | ||
6392 | #else | |
6393 | ||
6394 | pmem_start = pci_resource_start(pdev, 1); | |
6395 | pmem_len = pci_resource_len(pdev, 1); | |
6396 | pmem_flags = pci_resource_flags (pdev, 1); | |
6397 | ||
6398 | if (!(pmem_flags & IORESOURCE_MEM)) { | |
6399 | RT_TRACE(COMP_ERR,"region #1 not a MMIO resource, aborting"); | |
6400 | goto fail; | |
6401 | } | |
6402 | ||
6403 | //DMESG("Memory mapped space @ 0x%08lx ", pmem_start); | |
6404 | if( ! request_mem_region(pmem_start, pmem_len, RTL819xE_MODULE_NAME)) { | |
6405 | RT_TRACE(COMP_ERR,"request_mem_region failed!"); | |
6406 | goto fail; | |
6407 | } | |
6408 | ||
6409 | ||
6410 | ioaddr = (unsigned long)ioremap_nocache( pmem_start, pmem_len); | |
6411 | if( ioaddr == (unsigned long)NULL ){ | |
6412 | RT_TRACE(COMP_ERR,"ioremap failed!"); | |
6413 | // release_mem_region( pmem_start, pmem_len ); | |
6414 | goto fail1; | |
6415 | } | |
6416 | ||
6417 | dev->mem_start = ioaddr; // shared mem start | |
6418 | dev->mem_end = ioaddr + pci_resource_len(pdev, 0); // shared mem end | |
6419 | ||
6420 | #endif //end #ifdef RTL_IO_MAP | |
6421 | ||
6422 | /* We disable the RETRY_TIMEOUT register (0x41) to keep | |
6423 | * PCI Tx retries from interfering with C3 CPU state */ | |
6424 | pci_write_config_byte(pdev, 0x41, 0x00); | |
6425 | ||
6426 | ||
6427 | pci_read_config_byte(pdev, 0x05, &unit); | |
6428 | pci_write_config_byte(pdev, 0x05, unit & (~0x04)); | |
6429 | ||
6430 | dev->irq = pdev->irq; | |
6431 | priv->irq = 0; | |
6432 | ||
6433 | dev->netdev_ops = &rtl8192_netdev_ops; | |
6434 | #if 0 | |
6435 | dev->open = rtl8192_open; | |
6436 | dev->stop = rtl8192_close; | |
6437 | //dev->hard_start_xmit = rtl8192_8023_hard_start_xmit; | |
6438 | dev->tx_timeout = tx_timeout; | |
6439 | //dev->wireless_handlers = &r8192_wx_handlers_def; | |
6440 | dev->do_ioctl = rtl8192_ioctl; | |
6441 | dev->set_multicast_list = r8192_set_multicast; | |
6442 | dev->set_mac_address = r8192_set_mac_adr; | |
6443 | #endif | |
6444 | ||
6445 | //DMESG("Oops: i'm coming\n"); | |
6446 | #if WIRELESS_EXT >= 12 | |
6447 | #if WIRELESS_EXT < 17 | |
6448 | dev->get_wireless_stats = r8192_get_wireless_stats; | |
6449 | #endif | |
6450 | dev->wireless_handlers = (struct iw_handler_def *) &r8192_wx_handlers_def; | |
6451 | #endif | |
6452 | //dev->get_wireless_stats = r8192_get_wireless_stats; | |
6453 | dev->type=ARPHRD_ETHER; | |
6454 | ||
6455 | dev->watchdog_timeo = HZ*3; //modified by john, 0805 | |
6456 | ||
6457 | if (dev_alloc_name(dev, ifname) < 0){ | |
6458 | RT_TRACE(COMP_INIT, "Oops: devname already taken! Trying wlan%%d...\n"); | |
6459 | ifname = "wlan%d"; | |
6460 | dev_alloc_name(dev, ifname); | |
6461 | } | |
6462 | ||
6463 | RT_TRACE(COMP_INIT, "Driver probe completed1\n"); | |
6464 | if(rtl8192_init(dev)!=0){ | |
6465 | RT_TRACE(COMP_ERR, "Initialization failed"); | |
6466 | goto fail; | |
6467 | } | |
6468 | ||
6469 | netif_carrier_off(dev); | |
6470 | netif_stop_queue(dev); | |
6471 | ||
6472 | register_netdev(dev); | |
6473 | RT_TRACE(COMP_INIT, "dev name=======> %s\n",dev->name); | |
6474 | rtl8192_proc_init_one(dev); | |
6475 | ||
6476 | ||
6477 | RT_TRACE(COMP_INIT, "Driver probe completed\n"); | |
ecdfa446 | 6478 | return 0; |
ecdfa446 GKH |
6479 | |
6480 | fail1: | |
6481 | ||
6482 | #ifdef CONFIG_RTL8180_IO_MAP | |
6483 | ||
6484 | if( dev->base_addr != 0 ){ | |
6485 | ||
6486 | release_region(dev->base_addr, | |
6487 | pci_resource_len(pdev, 0) ); | |
6488 | } | |
6489 | #else | |
6490 | if( dev->mem_start != (unsigned long)NULL ){ | |
6491 | iounmap( (void *)dev->mem_start ); | |
6492 | release_mem_region( pci_resource_start(pdev, 1), | |
6493 | pci_resource_len(pdev, 1) ); | |
6494 | } | |
6495 | #endif //end #ifdef RTL_IO_MAP | |
6496 | ||
6497 | fail: | |
6498 | if(dev){ | |
6499 | ||
6500 | if (priv->irq) { | |
6501 | free_irq(dev->irq, dev); | |
6502 | dev->irq=0; | |
6503 | } | |
6504 | free_ieee80211(dev); | |
6505 | } | |
6506 | ||
6507 | pci_disable_device(pdev); | |
6508 | ||
6509 | DMESG("wlan driver load failed\n"); | |
6510 | pci_set_drvdata(pdev, NULL); | |
6511 | return -ENODEV; | |
6512 | ||
6513 | } | |
6514 | ||
6515 | /* detach all the work and timer structure declared or inititialized | |
6516 | * in r8192_init function. | |
6517 | * */ | |
6518 | void rtl8192_cancel_deferred_work(struct r8192_priv* priv) | |
6519 | { | |
6520 | /* call cancel_work_sync instead of cancel_delayed_work if and only if Linux_version_code | |
6521 | * is or is newer than 2.6.20 and work structure is defined to be struct work_struct. | |
6522 | * Otherwise call cancel_delayed_work is enough. | |
39cfb97b | 6523 | * FIXME (2.6.20 should 2.6.22, work_struct should not cancel) |
ecdfa446 | 6524 | * */ |
ecdfa446 GKH |
6525 | cancel_delayed_work(&priv->watch_dog_wq); |
6526 | cancel_delayed_work(&priv->update_beacon_wq); | |
6527 | cancel_delayed_work(&priv->ieee80211->hw_wakeup_wq); | |
6528 | cancel_delayed_work(&priv->ieee80211->hw_sleep_wq); | |
6529 | #ifdef RTL8192E | |
6530 | cancel_delayed_work(&priv->gpio_change_rf_wq); | |
6531 | #endif | |
ecdfa446 GKH |
6532 | cancel_work_sync(&priv->reset_wq); |
6533 | cancel_work_sync(&priv->qos_activate); | |
6534 | //cancel_work_sync(&priv->SetBWModeWorkItem); | |
6535 | //cancel_work_sync(&priv->SwChnlWorkItem); | |
ecdfa446 GKH |
6536 | |
6537 | } | |
6538 | ||
6539 | ||
6540 | static void __devexit rtl8192_pci_disconnect(struct pci_dev *pdev) | |
6541 | { | |
6542 | struct net_device *dev = pci_get_drvdata(pdev); | |
6543 | struct r8192_priv *priv ; | |
6544 | ||
6545 | if(dev){ | |
6546 | ||
6547 | unregister_netdev(dev); | |
6548 | ||
6549 | priv=ieee80211_priv(dev); | |
6550 | ||
6551 | rtl8192_proc_remove_one(dev); | |
6552 | ||
6553 | rtl8192_down(dev); | |
6554 | if (priv->pFirmware) | |
6555 | { | |
6556 | vfree(priv->pFirmware); | |
6557 | priv->pFirmware = NULL; | |
6558 | } | |
6559 | // priv->rf_close(dev); | |
6560 | // rtl8192_usb_deleteendpoints(dev); | |
ecdfa446 | 6561 | destroy_workqueue(priv->priv_wq); |
ecdfa446 GKH |
6562 | /* redundant with rtl8192_down */ |
6563 | // rtl8192_irq_disable(dev); | |
6564 | // rtl8192_reset(dev); | |
6565 | // mdelay(10); | |
6566 | { | |
6567 | u32 i; | |
6568 | /* free tx/rx rings */ | |
6569 | rtl8192_free_rx_ring(dev); | |
6570 | for (i = 0; i < MAX_TX_QUEUE_COUNT; i++) { | |
6571 | rtl8192_free_tx_ring(dev, i); | |
6572 | } | |
6573 | } | |
6574 | if(priv->irq){ | |
6575 | ||
6576 | printk("Freeing irq %d\n",dev->irq); | |
6577 | free_irq(dev->irq, dev); | |
6578 | priv->irq=0; | |
6579 | ||
6580 | } | |
6581 | ||
6582 | ||
6583 | ||
6584 | // free_beacon_desc_ring(dev,priv->txbeaconcount); | |
6585 | ||
6586 | #ifdef CONFIG_RTL8180_IO_MAP | |
6587 | ||
6588 | if( dev->base_addr != 0 ){ | |
6589 | ||
6590 | release_region(dev->base_addr, | |
6591 | pci_resource_len(pdev, 0) ); | |
6592 | } | |
6593 | #else | |
6594 | if( dev->mem_start != (unsigned long)NULL ){ | |
6595 | iounmap( (void *)dev->mem_start ); | |
6596 | release_mem_region( pci_resource_start(pdev, 1), | |
6597 | pci_resource_len(pdev, 1) ); | |
6598 | } | |
6599 | #endif /*end #ifdef RTL_IO_MAP*/ | |
6600 | free_ieee80211(dev); | |
6601 | ||
6602 | } | |
6603 | ||
6604 | pci_disable_device(pdev); | |
6605 | RT_TRACE(COMP_DOWN, "wlan driver removed\n"); | |
6606 | } | |
6607 | ||
fb5fe277 GK |
6608 | extern int ieee80211_rtl_init(void); |
6609 | extern void ieee80211_rtl_exit(void); | |
ecdfa446 GKH |
6610 | |
6611 | static int __init rtl8192_pci_module_init(void) | |
6612 | { | |
6613 | int retval; | |
6614 | ||
fb5fe277 | 6615 | retval = ieee80211_rtl_init(); |
ecdfa446 GKH |
6616 | if (retval) |
6617 | return retval; | |
6618 | ||
6619 | printk(KERN_INFO "\nLinux kernel driver for RTL8192 based WLAN cards\n"); | |
6620 | printk(KERN_INFO "Copyright (c) 2007-2008, Realsil Wlan\n"); | |
6621 | RT_TRACE(COMP_INIT, "Initializing module"); | |
6622 | RT_TRACE(COMP_INIT, "Wireless extensions version %d", WIRELESS_EXT); | |
6623 | rtl8192_proc_module_init(); | |
ecdfa446 | 6624 | if(0!=pci_register_driver(&rtl8192_pci_driver)) |
ecdfa446 GKH |
6625 | { |
6626 | DMESG("No device found"); | |
6627 | /*pci_unregister_driver (&rtl8192_pci_driver);*/ | |
6628 | return -ENODEV; | |
6629 | } | |
6630 | return 0; | |
6631 | } | |
6632 | ||
6633 | ||
6634 | static void __exit rtl8192_pci_module_exit(void) | |
6635 | { | |
6636 | pci_unregister_driver(&rtl8192_pci_driver); | |
6637 | ||
6638 | RT_TRACE(COMP_DOWN, "Exiting"); | |
6639 | rtl8192_proc_module_remove(); | |
fb5fe277 | 6640 | ieee80211_rtl_exit(); |
ecdfa446 GKH |
6641 | } |
6642 | ||
6643 | //warning message WB | |
ecdfa446 | 6644 | irqreturn_t rtl8192_interrupt(int irq, void *netdev) |
ecdfa446 GKH |
6645 | { |
6646 | struct net_device *dev = (struct net_device *) netdev; | |
6647 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
6648 | unsigned long flags; | |
6649 | u32 inta; | |
6650 | /* We should return IRQ_NONE, but for now let me keep this */ | |
6651 | if(priv->irq_enabled == 0){ | |
ecdfa446 | 6652 | return IRQ_HANDLED; |
ecdfa446 GKH |
6653 | } |
6654 | ||
6655 | spin_lock_irqsave(&priv->irq_th_lock,flags); | |
6656 | ||
6657 | //ISR: 4bytes | |
6658 | ||
6659 | inta = read_nic_dword(dev, ISR);// & priv->IntrMask; | |
6660 | write_nic_dword(dev,ISR,inta); // reset int situation | |
6661 | ||
6662 | priv->stats.shints++; | |
6663 | //DMESG("Enter interrupt, ISR value = 0x%08x", inta); | |
6664 | if(!inta){ | |
6665 | spin_unlock_irqrestore(&priv->irq_th_lock,flags); | |
ecdfa446 | 6666 | return IRQ_HANDLED; |
ecdfa446 GKH |
6667 | /* |
6668 | most probably we can safely return IRQ_NONE, | |
6669 | but for now is better to avoid problems | |
6670 | */ | |
6671 | } | |
6672 | ||
6673 | if(inta == 0xffff){ | |
6674 | /* HW disappared */ | |
6675 | spin_unlock_irqrestore(&priv->irq_th_lock,flags); | |
ecdfa446 | 6676 | return IRQ_HANDLED; |
ecdfa446 GKH |
6677 | } |
6678 | ||
6679 | priv->stats.ints++; | |
6680 | #ifdef DEBUG_IRQ | |
6681 | DMESG("NIC irq %x",inta); | |
6682 | #endif | |
6683 | //priv->irqpending = inta; | |
6684 | ||
6685 | ||
6686 | if(!netif_running(dev)) { | |
6687 | spin_unlock_irqrestore(&priv->irq_th_lock,flags); | |
ecdfa446 | 6688 | return IRQ_HANDLED; |
ecdfa446 GKH |
6689 | } |
6690 | ||
6691 | if(inta & IMR_TIMEOUT0){ | |
6692 | // write_nic_dword(dev, TimerInt, 0); | |
6693 | //DMESG("=================>waking up"); | |
6694 | // rtl8180_hw_wakeup(dev); | |
6695 | } | |
6696 | ||
6697 | if(inta & IMR_TBDOK){ | |
6698 | RT_TRACE(COMP_INTR, "beacon ok interrupt!\n"); | |
6699 | rtl8192_tx_isr(dev, BEACON_QUEUE); | |
6700 | priv->stats.txbeaconokint++; | |
6701 | } | |
6702 | ||
6703 | if(inta & IMR_TBDER){ | |
6704 | RT_TRACE(COMP_INTR, "beacon ok interrupt!\n"); | |
6705 | rtl8192_tx_isr(dev, BEACON_QUEUE); | |
6706 | priv->stats.txbeaconerr++; | |
6707 | } | |
6708 | ||
6709 | if(inta & IMR_MGNTDOK ) { | |
6710 | RT_TRACE(COMP_INTR, "Manage ok interrupt!\n"); | |
6711 | priv->stats.txmanageokint++; | |
6712 | rtl8192_tx_isr(dev,MGNT_QUEUE); | |
6713 | ||
6714 | } | |
6715 | ||
6716 | if(inta & IMR_COMDOK) | |
6717 | { | |
6718 | priv->stats.txcmdpktokint++; | |
6719 | rtl8192_tx_isr(dev,TXCMD_QUEUE); | |
6720 | } | |
6721 | ||
6722 | if(inta & IMR_ROK){ | |
6723 | #ifdef DEBUG_RX | |
6724 | DMESG("Frame arrived !"); | |
6725 | #endif | |
6726 | priv->stats.rxint++; | |
6727 | tasklet_schedule(&priv->irq_rx_tasklet); | |
6728 | } | |
6729 | ||
6730 | if(inta & IMR_BcnInt) { | |
6731 | RT_TRACE(COMP_INTR, "prepare beacon for interrupt!\n"); | |
6732 | tasklet_schedule(&priv->irq_prepare_beacon_tasklet); | |
6733 | } | |
6734 | ||
6735 | if(inta & IMR_RDU){ | |
6736 | RT_TRACE(COMP_INTR, "rx descriptor unavailable!\n"); | |
6737 | priv->stats.rxrdu++; | |
6738 | /* reset int situation */ | |
6739 | write_nic_dword(dev,INTA_MASK,read_nic_dword(dev, INTA_MASK) & ~IMR_RDU); | |
6740 | tasklet_schedule(&priv->irq_rx_tasklet); | |
6741 | } | |
6742 | ||
6743 | if(inta & IMR_RXFOVW){ | |
6744 | RT_TRACE(COMP_INTR, "rx overflow !\n"); | |
6745 | priv->stats.rxoverflow++; | |
6746 | tasklet_schedule(&priv->irq_rx_tasklet); | |
6747 | } | |
6748 | ||
6749 | if(inta & IMR_TXFOVW) priv->stats.txoverflow++; | |
6750 | ||
6751 | if(inta & IMR_BKDOK){ | |
6752 | RT_TRACE(COMP_INTR, "BK Tx OK interrupt!\n"); | |
6753 | priv->stats.txbkokint++; | |
6754 | priv->ieee80211->LinkDetectInfo.NumTxOkInPeriod++; | |
6755 | rtl8192_tx_isr(dev,BK_QUEUE); | |
6756 | rtl8192_try_wake_queue(dev, BK_QUEUE); | |
6757 | } | |
6758 | ||
6759 | if(inta & IMR_BEDOK){ | |
6760 | RT_TRACE(COMP_INTR, "BE TX OK interrupt!\n"); | |
6761 | priv->stats.txbeokint++; | |
6762 | priv->ieee80211->LinkDetectInfo.NumTxOkInPeriod++; | |
6763 | rtl8192_tx_isr(dev,BE_QUEUE); | |
6764 | rtl8192_try_wake_queue(dev, BE_QUEUE); | |
6765 | } | |
6766 | ||
6767 | if(inta & IMR_VIDOK){ | |
6768 | RT_TRACE(COMP_INTR, "VI TX OK interrupt!\n"); | |
6769 | priv->stats.txviokint++; | |
6770 | priv->ieee80211->LinkDetectInfo.NumTxOkInPeriod++; | |
6771 | rtl8192_tx_isr(dev,VI_QUEUE); | |
6772 | rtl8192_try_wake_queue(dev, VI_QUEUE); | |
6773 | } | |
6774 | ||
6775 | if(inta & IMR_VODOK){ | |
6776 | priv->stats.txvookint++; | |
6777 | priv->ieee80211->LinkDetectInfo.NumTxOkInPeriod++; | |
6778 | rtl8192_tx_isr(dev,VO_QUEUE); | |
6779 | rtl8192_try_wake_queue(dev, VO_QUEUE); | |
6780 | } | |
6781 | ||
6782 | force_pci_posting(dev); | |
6783 | spin_unlock_irqrestore(&priv->irq_th_lock,flags); | |
6784 | ||
ecdfa446 | 6785 | return IRQ_HANDLED; |
ecdfa446 GKH |
6786 | } |
6787 | ||
6788 | void rtl8192_try_wake_queue(struct net_device *dev, int pri) | |
6789 | { | |
6790 | #if 0 | |
6791 | unsigned long flags; | |
6792 | short enough_desc; | |
6793 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
6794 | ||
6795 | spin_lock_irqsave(&priv->tx_lock,flags); | |
6796 | enough_desc = check_nic_enough_desc(dev,pri); | |
6797 | spin_unlock_irqrestore(&priv->tx_lock,flags); | |
6798 | ||
6799 | if(enough_desc) | |
fb5fe277 | 6800 | ieee80211_rtl_wake_queue(priv->ieee80211); |
ecdfa446 GKH |
6801 | #endif |
6802 | } | |
6803 | ||
6804 | ||
6805 | void EnableHWSecurityConfig8192(struct net_device *dev) | |
6806 | { | |
6807 | u8 SECR_value = 0x0; | |
6808 | // struct ieee80211_device* ieee1 = container_of(&dev, struct ieee80211_device, dev); | |
6809 | //printk("==>ieee1:%p, dev:%p\n", ieee1, dev); | |
6810 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
6811 | struct ieee80211_device* ieee = priv->ieee80211; | |
6812 | //printk("==>ieee:%p, dev:%p\n", ieee, dev); | |
6813 | SECR_value = SCR_TxEncEnable | SCR_RxDecEnable; | |
6814 | #if 1 | |
6815 | if (((KEY_TYPE_WEP40 == ieee->pairwise_key_type) || (KEY_TYPE_WEP104 == ieee->pairwise_key_type)) && (priv->ieee80211->auth_mode != 2)) | |
6816 | { | |
6817 | SECR_value |= SCR_RxUseDK; | |
6818 | SECR_value |= SCR_TxUseDK; | |
6819 | } | |
6820 | else if ((ieee->iw_mode == IW_MODE_ADHOC) && (ieee->pairwise_key_type & (KEY_TYPE_CCMP | KEY_TYPE_TKIP))) | |
6821 | { | |
6822 | SECR_value |= SCR_RxUseDK; | |
6823 | SECR_value |= SCR_TxUseDK; | |
6824 | } | |
6825 | ||
6826 | #endif | |
6827 | ||
6828 | //add HWSec active enable here. | |
6829 | //default using hwsec. when peer AP is in N mode only and pairwise_key_type is none_aes(which HT_IOT_ACT_PURE_N_MODE indicates it), use software security. when peer AP is in b,g,n mode mixed and pairwise_key_type is none_aes, use g mode hw security. WB on 2008.7.4 | |
6830 | ieee->hwsec_active = 1; | |
6831 | ||
6832 | if ((ieee->pHTInfo->IOTAction&HT_IOT_ACT_PURE_N_MODE) || !hwwep)//!ieee->hwsec_support) //add hwsec_support flag to totol control hw_sec on/off | |
6833 | { | |
6834 | ieee->hwsec_active = 0; | |
6835 | SECR_value &= ~SCR_RxDecEnable; | |
6836 | } | |
6837 | ||
6838 | RT_TRACE(COMP_SEC,"%s:, hwsec:%d, pairwise_key:%d, SECR_value:%x\n", __FUNCTION__, \ | |
6839 | ieee->hwsec_active, ieee->pairwise_key_type, SECR_value); | |
6840 | { | |
6841 | write_nic_byte(dev, SECR, SECR_value);//SECR_value | SCR_UseDK ); | |
6842 | } | |
6843 | ||
6844 | } | |
6845 | #define TOTAL_CAM_ENTRY 32 | |
6846 | //#define CAM_CONTENT_COUNT 8 | |
6847 | void setKey( struct net_device *dev, | |
6848 | u8 EntryNo, | |
6849 | u8 KeyIndex, | |
6850 | u16 KeyType, | |
6851 | u8 *MacAddr, | |
6852 | u8 DefaultKey, | |
6853 | u32 *KeyContent ) | |
6854 | { | |
6855 | u32 TargetCommand = 0; | |
6856 | u32 TargetContent = 0; | |
6857 | u16 usConfig = 0; | |
6858 | u8 i; | |
6859 | #ifdef ENABLE_IPS | |
6860 | struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev); | |
6861 | RT_RF_POWER_STATE rtState; | |
6862 | rtState = priv->ieee80211->eRFPowerState; | |
6863 | if(priv->ieee80211->PowerSaveControl.bInactivePs){ | |
6864 | if(rtState == eRfOff){ | |
6865 | if(priv->ieee80211->RfOffReason > RF_CHANGE_BY_IPS) | |
6866 | { | |
6867 | RT_TRACE(COMP_ERR, "%s(): RF is OFF.\n",__FUNCTION__); | |
65a43784 | 6868 | //up(&priv->wx_sem); |
ecdfa446 GKH |
6869 | return ; |
6870 | } | |
6871 | else{ | |
65a43784 | 6872 | down(&priv->ieee80211->ips_sem); |
ecdfa446 | 6873 | IPSLeave(dev); |
65a43784 | 6874 | up(&priv->ieee80211->ips_sem); |
ecdfa446 GKH |
6875 | } |
6876 | } | |
6877 | } | |
6878 | priv->ieee80211->is_set_key = true; | |
6879 | #endif | |
6880 | if (EntryNo >= TOTAL_CAM_ENTRY) | |
6881 | RT_TRACE(COMP_ERR, "cam entry exceeds in setKey()\n"); | |
6882 | ||
0ee9f67c | 6883 | RT_TRACE(COMP_SEC, "====>to setKey(), dev:%p, EntryNo:%d, KeyIndex:%d, KeyType:%d, MacAddr%pM\n", dev,EntryNo, KeyIndex, KeyType, MacAddr); |
ecdfa446 GKH |
6884 | |
6885 | if (DefaultKey) | |
6886 | usConfig |= BIT15 | (KeyType<<2); | |
6887 | else | |
6888 | usConfig |= BIT15 | (KeyType<<2) | KeyIndex; | |
6889 | // usConfig |= BIT15 | (KeyType<<2) | (DefaultKey<<5) | KeyIndex; | |
6890 | ||
6891 | ||
6892 | for(i=0 ; i<CAM_CONTENT_COUNT; i++){ | |
6893 | TargetCommand = i+CAM_CONTENT_COUNT*EntryNo; | |
6894 | TargetCommand |= BIT31|BIT16; | |
6895 | ||
6896 | if(i==0){//MAC|Config | |
6897 | TargetContent = (u32)(*(MacAddr+0)) << 16| | |
6898 | (u32)(*(MacAddr+1)) << 24| | |
6899 | (u32)usConfig; | |
6900 | ||
6901 | write_nic_dword(dev, WCAMI, TargetContent); | |
6902 | write_nic_dword(dev, RWCAM, TargetCommand); | |
6903 | // printk("setkey cam =%8x\n", read_cam(dev, i+6*EntryNo)); | |
6904 | } | |
6905 | else if(i==1){//MAC | |
6906 | TargetContent = (u32)(*(MacAddr+2)) | | |
6907 | (u32)(*(MacAddr+3)) << 8| | |
6908 | (u32)(*(MacAddr+4)) << 16| | |
6909 | (u32)(*(MacAddr+5)) << 24; | |
6910 | write_nic_dword(dev, WCAMI, TargetContent); | |
6911 | write_nic_dword(dev, RWCAM, TargetCommand); | |
6912 | } | |
6913 | else { //Key Material | |
6914 | if(KeyContent != NULL) | |
6915 | { | |
6916 | write_nic_dword(dev, WCAMI, (u32)(*(KeyContent+i-2)) ); | |
6917 | write_nic_dword(dev, RWCAM, TargetCommand); | |
6918 | } | |
6919 | } | |
6920 | } | |
6921 | RT_TRACE(COMP_SEC,"=========>after set key, usconfig:%x\n", usConfig); | |
ecdfa446 GKH |
6922 | } |
6923 | // This function seems not ready! WB | |
6924 | void CamPrintDbgReg(struct net_device* dev) | |
6925 | { | |
6926 | unsigned long rvalue; | |
6927 | unsigned char ucValue; | |
6928 | write_nic_dword(dev, DCAM, 0x80000000); | |
6929 | msleep(40); | |
6930 | rvalue = read_nic_dword(dev, DCAM); //delay_ms(40); | |
6931 | RT_TRACE(COMP_SEC, " TX CAM=%8lX ",rvalue); | |
6932 | if((rvalue & 0x40000000) != 0x4000000) | |
6933 | RT_TRACE(COMP_SEC, "-->TX Key Not Found "); | |
6934 | msleep(20); | |
6935 | write_nic_dword(dev, DCAM, 0x00000000); //delay_ms(40); | |
6936 | rvalue = read_nic_dword(dev, DCAM); //delay_ms(40); | |
6937 | RT_TRACE(COMP_SEC, "RX CAM=%8lX ",rvalue); | |
6938 | if((rvalue & 0x40000000) != 0x4000000) | |
6939 | RT_TRACE(COMP_SEC, "-->CAM Key Not Found "); | |
6940 | ucValue = read_nic_byte(dev, SECR); | |
6941 | RT_TRACE(COMP_SEC, "WPA_Config=%x \n",ucValue); | |
6942 | } | |
6943 | ||
65a43784 | 6944 | bool NicIFEnableNIC(struct net_device* dev) |
6945 | { | |
6946 | RT_STATUS init_status = RT_STATUS_SUCCESS; | |
6947 | struct r8192_priv* priv = ieee80211_priv(dev); | |
6948 | PRT_POWER_SAVE_CONTROL pPSC = (PRT_POWER_SAVE_CONTROL)(&(priv->ieee80211->PowerSaveControl)); | |
6949 | ||
6950 | //YJ,add,091109 | |
6951 | if (priv->up == 0){ | |
6952 | RT_TRACE(COMP_ERR, "ERR!!! %s(): Driver is already down!\n",__FUNCTION__); | |
6953 | priv->bdisable_nic = false; //YJ,add,091111 | |
6954 | return false; | |
6955 | } | |
6956 | // <1> Reset memory: descriptor, buffer,.. | |
6957 | //NicIFResetMemory(Adapter); | |
6958 | ||
6959 | // <2> Enable Adapter | |
6960 | //printk("===========>%s()\n",__FUNCTION__); | |
6961 | //priv->bfirst_init = true; | |
6962 | init_status = rtl8192_adapter_start(dev); | |
6963 | if (init_status != RT_STATUS_SUCCESS) { | |
6964 | RT_TRACE(COMP_ERR,"ERR!!! %s(): initialization is failed!\n",__FUNCTION__); | |
6965 | priv->bdisable_nic = false; //YJ,add,091111 | |
6966 | return -1; | |
6967 | } | |
6968 | //printk("start adapter finished\n"); | |
6969 | RT_CLEAR_PS_LEVEL(pPSC, RT_RF_OFF_LEVL_HALT_NIC); | |
6970 | //priv->bfirst_init = false; | |
6971 | ||
6972 | // <3> Enable Interrupt | |
6973 | rtl8192_irq_enable(dev); | |
6974 | priv->bdisable_nic = false; | |
6975 | //RT_TRACE(COMP_PS,"<===========%s()\n",__FUNCTION__); | |
6976 | return (init_status == RT_STATUS_SUCCESS) ? true:false; | |
6977 | } | |
6978 | bool NicIFDisableNIC(struct net_device* dev) | |
6979 | { | |
6980 | bool status = true; | |
6981 | struct r8192_priv* priv = ieee80211_priv(dev); | |
6982 | u8 tmp_state = 0; | |
6983 | // <1> Disable Interrupt | |
6984 | //RT_TRACE(COMP_PS, "=========>%s()\n",__FUNCTION__); | |
6985 | priv->bdisable_nic = true; //YJ,move,091109 | |
6986 | tmp_state = priv->ieee80211->state; | |
6987 | ||
6988 | ieee80211_softmac_stop_protocol(priv->ieee80211, false); | |
6989 | ||
6990 | priv->ieee80211->state = tmp_state; | |
6991 | rtl8192_cancel_deferred_work(priv); | |
6992 | rtl8192_irq_disable(dev); | |
6993 | // <2> Stop all timer | |
6994 | ||
6995 | // <3> Disable Adapter | |
6996 | rtl8192_halt_adapter(dev, false); | |
6997 | // priv->bdisable_nic = true; | |
6998 | //RT_TRACE(COMP_PS, "<=========%s()\n",__FUNCTION__); | |
6999 | ||
7000 | return status; | |
7001 | } | |
7002 | ||
ecdfa446 GKH |
7003 | |
7004 | /*************************************************************************** | |
7005 | ------------------- module init / exit stubs ---------------- | |
7006 | ****************************************************************************/ | |
7007 | module_init(rtl8192_pci_module_init); | |
7008 | module_exit(rtl8192_pci_module_exit); |